Interfacial Reconstructed Layer Controls the Orientation of Monolayer Transition-Metal Dichalcogenides.

Growing continuous monolayer films of transition-metal dichalcogenides (TMDs) without the disruption of grain boundaries is essential to realize the full potential of these materials for future electronics and optoelectronics, but it remains a formidable challenge. It is generally believed that controlling the TMDs orientations on epitaxial substrates stems from matching the atomic registry, symmetry, and penetrable van der Waals forces. Interfacial reconstruction within the exceedingly narrow substrate-epilayer gap has been anticipated. However, its role in the growth mechanism has not been intensively investigated. Here, we report the experimental conformation of an interfacial reconstructed (IR) layer within the substrate-epilayer gap. Such an IR layer profoundly impacts the orientations of nucleating TMDs domains and, thus, affects the materials' properties. These findings provide deeper insights into the buried interface that could have profound implications for the development of TMD-based electronics and optoelectronics.

The Energy Level Conundrum of Organic Semiconductors in Solar Cells.

The frontier molecular energy levels of organic semiconductors are decisive for their fundamental function and efficiency in optoelectronics. However, the precise determination of these energy levels and their variation when using different techniques makes it hard to compare and establish design rules. In this work, the energy levels of 33 organic semiconductors via cyclic voltammetry (CV), density functional theory, ultraviolet photoelectron spectroscopy, and low-energy inverse photoelectron spectroscopy are determined. Solar cells are fabricated to obtain key device parameters and relate them to the significant differences in the energy levels and offsets obtained from different methods. In contrast to CV, the photovoltaic gap measured using photoelectron spectroscopy (PES) correlates well with the experimental device VOC . It is demonstrated that high-performing systems such as PM6:Y6 and WF3F:Y6, which are previously reported to have negligible ionization energy (IE) offsets (ΔIE), possess sizable ΔIE of ≈0.5 eV, determined by PES. Using various D-A blends, it is demonstrated that ΔIE plays a key role in charge generation. In contrast to earlier reports, it is shown that a vanishing ΔIE is detrimental to device performance. Overall, these findings establish a solid base for reliably evaluating material energetics and interpreting property-performance relationships in organic solar cells.

Rapid and up-scalable manufacturing of gigahertz nanogap diodes.

The massive deployment of fifth generation and internet of things technologies requires precise and high-throughput fabrication techniques for the mass production of radio frequency electronics. We use printable indium-gallium-zinc-oxide semiconductor in spontaneously formed self-aligned <10 nm nanogaps and flash-lamp annealing to demonstrate rapid manufacturing of nanogap Schottky diodes over arbitrary size substrates operating in 5 G frequencies. These diodes combine low junction capacitance with low turn-on voltage while exhibiting cut-off frequencies (intrinsic) of >100 GHz. Rectifier circuits constructed with these co-planar diodes can operate at ~47 GHz (extrinsic), making them the fastest large-area electronic devices demonstrated to date.

14 GHz Schottky Diodes Using a p-Doped Organic Polymer.

The low carrier mobility of organic semiconductors and the high parasitic resistance and capacitance often encountered in conventional organic Schottky diodes hinder their deployment in emerging radio frequency (RF) electronics. Here, these limitations are overcome by combining self-aligned asymmetric nanogap electrodes (≈25 nm) produced by adhesion lithography, with a high mobility organic semiconductor, and RF Schottky diodes able to operate in the 5G frequency spectrum are demonstrated. C16 IDT-BT is used, as the high hole mobility polymer, and the impact of p-doping on the diode performance is studied. Pristine C16 IDT-BT-based diodes exhibit maximum intrinsic and extrinsic cutoff frequencies (fC ) of >100 and 6 GHz, respectively. This extraordinary performance is attributed to the planar nature of the nanogap channel and the diode's small junction capacitance (<2 pF). Doping of C16 IDT-BT with the molecular p-dopant C60 F48 improves the diode's performance further by reducing the series resistance resulting to intrinsic and extrinsic fC of >100 and ≈14 GHz respectively, while the DC output voltage of an RF rectifier circuit increases by a tenfold. Our work highlights the importance of the planar nanogap architecture and paves the way for the use of organic Schottky diodes in large-area RF electronics of the future.

A Universal Cosolvent Evaporation Strategy Enables Direct Printing of Perovskite Single Crystals for Optoelectronic Device Applications.

Solution-processed metal halide perovskite (MHP) single crystals (SCs) are in high demand for a growing number of printed electronic applications due to their superior optoelectronic properties compared to polycrystalline thin films. There is an urgent need to make SC fabrication facile, scalable, and compatible with the printed electronic manufacturing infrastructure. Here, a universal cosolvent evaporation (CSE) strategy is presented by which perovskite SCs and arrays are produced directly on substrates via printing and coating methods within minutes at room temperature from drying droplets. The CSE strategy successfully guides the supersaturation via controlled drying of droplets to suppress all crystallization pathways but one, and is shown to produce SCs of a wide variety of 3D, 2D, and mixed-cation/halide perovskites with consistency. This approach works with commonly used precursors and solvents, making it universal. Importantly, the SC consumes the precursor in the droplet, which enables the large-scale fabrication of SC arrays with minimal residue. Direct on-chip fabrication of 3D and 2D perovskite photodetector devices with outstanding performance is demonstrated. The approach shows that any MHP SC can now be manufactured on substrates using precision printing and scalable, high-throughput coating methods.

Printed Memtransistor Utilizing a Hybrid Perovskite/Organic Heterojunction Channel.

Neuromorphic computing has the potential to address the inherent limitations of conventional integrated circuit technology, ranging from perception, pattern recognition, to memory and decision-making ( Acc. Chem. Res. 2019, 52 (4), 964-974) ( Nature 2004, 431 (7010), 796-803) ( Nat. Nanotechnol. 2013, 8 (1), 13-24). Despite their low power consumption ( Nano Lett. 2016, 16 (11), 6724-6732), traditional two-terminal memristors can perform only a single function while lacking heterosynaptic plasticity ( Nanotechnology 2013, 24 (38), 382001). Inspired by the unconditioned reflex, multiterminal memristive transistors (memtransistor) were developed to realize complex functions, such as multiterminal modulation and heterosynaptic plasticity ( Nature 2018, 554, (7693), 500-504). Here we combine a hybrid metal halide perovskite with an organic conjugated polymer to form heterojunction transistors that are responsive to both electrical and optical stimuli. We show that the synergistic effects of photoinduced ion migration in the perovskite and electronic transport in the polymer layers can be exploited to realize memristive functions. The device combines reversible, nonvolatile conductance modulation with large switching current ratios, high endurance, and long retention times. Using in situ scanning Kelvin probe microscopy and variable-temperature charge transport measurement, we correlate the collective effects of bias-induced and photoinduced ion migration with the heterosynaptic behavior observed in this hybrid memtransistor. The hybrid heterojunction channel concept is expected to be applicable to other material combinations making it a promising platform for deployment in innovative neuromorphic devices of the future.

18.4 % Organic Solar Cells Using a High Ionization Energy Self-Assembled Monolayer as Hole-Extraction Interlayer.

Self-assembled monolayers (SAMs) based on Br-2PACz ([2-(3,6-dibromo-9H-carbazol-9-yl)ethyl]phosphonic acid) 2PACz ([2-(9H-Carbazol-9-yl)ethyl]phosphonic acid) and MeO-2PACz ([2-(3,6-dimethoxy-9H-carbazol-9-yl)ethyl]phosphonic acid) molecules were investigated as hole-extracting interlayers in organic photovoltaics (OPVs). The highest occupied molecular orbital (HOMO) energies of these SAMs were measured at -6.01 and -5.30 eV for Br-2PACz and MeO-2PACz, respectively, and found to induce significant changes in the work function (WF) of indium-tin-oxide (ITO) electrodes upon chemical functionalization. OPV cells based on PM6 (poly[(2,6-(4,8-bis(5-(2-ethylhexyl-3-fluoro)thiophen-2-yl)-benzo[1,2-b:4,5-b']dithiophene))-alt-(5,5-(1',3'-di-2-thienyl-5',7'-bis(2-ethylhexyl)benzo[1',2'-c:4',5'-c']dithiophene-4,8-dione)]) : BTP-eC9 : PC71 BM ([6,6]-phenyl-C71-butyric acid methyl ester) using ITO/Br-2PACz anodes exhibited a maximum power conversion efficiency (PCE) of 18.4 %, outperforming devices with ITO/MeO-2PACz (14.5 %) and ITO/poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT : PSS) (17.5 %). The higher PCE was found to originate from the much higher WF of ITO/Br-2PACz (-5.81 eV) compared to ITO/MeO-2PACz (4.58 eV) and ITO/PEDOT : PSS (4.9 eV), resulting in lower interface resistance, improved hole transport/extraction, lower trap-assisted recombination, and longer carrier lifetimes. Importantly, the ITO/Br-2PACz electrode was chemically stable, and after removal of the SAM it could be recycled and reused to construct fresh OPVs with equally impressive performance.

Ruddlesden-Popper-Phase Hybrid Halide Perovskite/Small-Molecule Organic Blend Memory Transistors.

Controlling the morphology of metal halide perovskite layers during processing is critical for the manufacturing of optoelectronics. Here, a strategy to control the microstructure of solution-processed layered Ruddlesden-Popper-phase perovskite films based on phenethylammonium lead bromide ((PEA)2 PbBr4 ) is reported. The method relies on the addition of the organic semiconductor 2,7-dioctyl[1]benzothieno[3,2-b]benzothiophene (C8 -BTBT) into the perovskite formulation, where it facilitates the formation of large, near-single-crystalline-quality platelet-like (PEA)2 PbBr4 domains overlaid by a ≈5-nm-thin C8 -BTBT layer. Transistors with (PEA)2 PbBr4 /C8 -BTBT channels exhibit an unexpectedly large hysteresis window between forward and return bias sweeps. Material and device analysis combined with theoretical calculations suggest that the C8 -BTBT-rich phase acts as the hole-transporting channel, while the quantum wells in (PEA)2 PbBr4 act as the charge storage element where carriers from the channel are injected, stored, or extracted via tunneling. When tested as a non-volatile memory, the devices exhibit a record memory window (>180 V), a high erase/write channel current ratio (104 ), good data retention, and high endurance (>104 cycles). The results here highlight a new memory device concept for application in large-area electronics, while the growth technique can potentially be exploited for the development of other optoelectronic devices including solar cells, photodetectors, and light-emitting diodes.

Ledge-directed epitaxy of continuously self-aligned single-crystalline nanoribbons of transition metal dichalcogenides.

Two-dimensional transition metal dichalcogenide nanoribbons are touted as the future extreme device downscaling for advanced logic and memory devices but remain a formidable synthetic challenge. Here, we demonstrate a ledge-directed epitaxy (LDE) of dense arrays of continuous, self-aligned, monolayer and single-crystalline MoS2 nanoribbons on ß-gallium (III) oxide (ß-Ga2O3) (100) substrates. LDE MoS2 nanoribbons have spatial uniformity over a long range and transport characteristics on par with those seen in exfoliated benchmarks. Prototype MoS2-nanoribbon-based field-effect transistors exhibit high on/off ratios of 108 and an averaged room temperature electron mobility of 65 cm2 V-1 s-1. The MoS2 nanoribbons can be readily transferred to arbitrary substrates while the underlying ß-Ga2O3 can be reused after mechanical exfoliation. We further demonstrate LDE as a versatile epitaxy platform for the growth of p-type WSe2 nanoribbons and lateral heterostructures made of p-WSe2 and n-MoS2 nanoribbons for futuristic electronics applications.

Rapid Photonic Processing of High-Electron-Mobility PbS Colloidal Quantum Dot Transistors.

Recent advances in solution-processable semiconducting colloidal quantum dots (CQDs) have enabled their use in a range of (opto)electronic devices. In most of these studies, device fabrication relied almost exclusively on thermal annealing to remove organic residues and enhance inter-CQD electronic coupling. Despite its widespread use, however, thermal annealing is a lengthy process, while its effectiveness to eliminate organic residues remains limited. Here, we exploit the use of xenon flash lamp sintering to post-treat solution-deposited layers of lead sulfide (PbS) CQDs and their application in n-channel thin-film transistors (TFTs). The process is simple, fast, and highly scalable and allows for efficient removal of organic residues while preserving both quantum confinement and high channel current modulation. Bottom-gate, top-contact PbS CQD TFTs incorporating SiO2 as the gate dielectric exhibit a maximum electron mobility of 0.2 cm2 V-1 s-1, a value higher than that of control transistors (≈10-2 cm2 V-1 s-1) processed via thermal annealing for 30 min at 120 °C. Replacing SiO2 with a polymeric dielectric improves the transistor's channel interface, leading to a significant increase in electron mobility to 3.7 cm2 V-1 s-1. The present work highlights the potential of flash lamp annealing as a promising method for the rapid manufacture of PbS CQD-based (opto)electronic devices and circuits.

17.1% Efficient Single-Junction Organic Solar Cells Enabled by n-Type Doping of the Bulk-Heterojunction.

Molecular doping is often used in organic semiconductors to tune their (opto)electronic properties. Despite its versatility, however, its application in organic photovoltaics (OPVs) remains limited and restricted to p-type dopants. In an effort to control the charge transport within the bulk-heterojunction (BHJ) of OPVs, the n-type dopant benzyl viologen (BV) is incorporated in a BHJ composed of the donor polymer PM6 and the small-molecule acceptor IT-4F. The power conversion efficiency (PCE) of the cells is found to increase from 13.2% to 14.4% upon addition of 0.004 wt% BV. Analysis of the photoactive materials and devices reveals that BV acts simultaneously as n-type dopant and microstructure modifier for the BHJ. Under optimal BV concentrations, these synergistic effects result in balanced hole and electron mobilities, higher absorption coefficients and increased charge-carrier density within the BHJ, while significantly extending the cells' shelf-lifetime. The n-type doping strategy is applied to five additional BHJ systems, for which similarly remarkable performance improvements are obtained. OPVs of particular interest are based on the ternary PM6:Y6:PC71BM:BV(0.004 wt%) blend for which a maximum PCE of 17.1%, is obtained. The effectiveness of the n-doping strategy highlights electron transport in NFA-based OPVs as being a key issue.

17% Efficient Organic Solar Cells Based on Liquid Exfoliated WS2 as a Replacement for PEDOT:PSS.

The application of liquid-exfoliated 2D transition metal disulfides (TMDs) as the hole transport layers (HTLs) in nonfullerene-based organic solar cells is reported. It is shown that solution processing of few-layer WS2 or MoS2 suspensions directly onto transparent indium tin oxide (ITO) electrodes changes their work function without the need for any further treatment. HTLs comprising WS2 are found to exhibit higher uniformity on ITO than those of MoS2 and consistently yield solar cells with superior power conversion efficiency (PCE), improved fill factor (FF), enhanced short-circuit current (JSC ), and lower series resistance than devices based on poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) and MoS2 . Cells based on the ternary bulk-heterojunction PBDB-T-2F:Y6:PC71 BM with WS2 as the HTL exhibit the highest PCE of 17%, with an FF of 78%, open-circuit voltage of 0.84 V, and a JSC of 26 mA cm-2 . Analysis of the cells' optical and carrier recombination characteristics indicates that the enhanced performance is most likely attributed to a combination of favorable photonic structure and reduced bimolecular recombination losses in WS2 -based cells. The achieved PCE is the highest reported to date for organic solar cells comprised of 2D charge transport interlayers and highlights the potential of TMDs as inexpensive HTLs for high-efficiency organic photovoltaics.

Double Charged Surface Layers in Lead Halide Perovskite Crystals.

Understanding defect chemistry, particularly ion migration, and its significant effect on the surface's optical and electronic properties is one of the major challenges impeding the development of hybrid perovskite-based devices. Here, using both experimental and theoretical approaches, we demonstrated that the surface layers of the perovskite crystals may acquire a high concentration of positively charged vacancies with the complementary negatively charged halide ions pushed to the surface. This charge separation near the surface generates an electric field that can induce an increase of optical band gap in the surface layers relative to the bulk. We found that the charge separation, electric field, and the amplitude of shift in the bandgap strongly depend on the halides and organic moieties of perovskite crystals. Our findings reveal the peculiarity of surface effects that are currently limiting the applications of perovskite crystals and more importantly explain their origins, thus enabling viable surface passivation strategies to remediate them.

Zero-Dimensional Cs4PbBr6 Perovskite Nanocrystals.

Perovskite nanocrystals (NCs) have become leading candidates for solution-processed optoelectronics applications. While substantial work has been published on 3-D perovskite phases, the NC form of the zero-dimensional (0-D) phase of this promising class of materials remains elusive. Here we report the synthesis of a new class of colloidal semiconductor NCs based on Cs4PbBr6, the 0-D perovskite, enabled through the design of a novel low-temperature reverse microemulsion method with 85% reaction yield. These 0-D perovskite NCs exhibit high photoluminescence quantum yield (PLQY) in the colloidal form (PLQY: 65%), and, more importantly, in the form of thin film (PLQY: 54%). Notably, the latter is among the highest values reported so far for perovskite NCs in the solid form. Our work brings the 0-D phase of perovskite into the realm of colloidal NCs with appealingly high PLQY in the film form, which paves the way for their practical application in real devices.

Temperature-Induced Lattice Relaxation of Perovskite Crystal Enhances Optoelectronic Properties and Solar Cell Performance.

Hybrid organic-inorganic perovskite crystals have recently become one of the most important classes of photoactive materials in the solar cell and optoelectronic communities. Albeit improvements have focused on state-of-the-art technology including various fabrication methods, device architectures, and surface passivation, progress is yet to be made in understanding the actual operational temperature on the electronic properties and the device performances. Therefore, the substantial effect of temperature on the optoelectronic properties, charge separation, charge recombination dynamics, and photoconversion efficiency are explored. The results clearly demonstrated a significant enhancement in the carrier mobility, photocurrent, charge carrier lifetime, and solar cell performance in the 60 ± 5 °C temperature range. In this temperature range, perovskite crystal exhibits a highly symmetrical relaxed cubic structure with well-aligned domains that are perpendicular to a principal axis, thereby remarkably improving the device operation. This finding provides a new key variable component and paves the way toward using perovskite crystals in highly efficient photovoltaic cells.

Harnessing Knowledge on Very Important Pharmacogenes CYP2C9 and CYP2C19 Variation for Precision Medicine in Resource-Limited Global Conflict Zones.

Pharmacogenomics harnesses the utility of a patient's genome (n = 1) in decisions on which therapeutic drugs and in what amounts should be administered. Often, patients with shared ancestry present with comparable genetic profiles that predict drug response. However, populations are not static, thus, often, population mobility through migration, especially enmasse as is seen for refugees, changes the pharmacogenetic profiles of resultant populations and therefore observed responses to commonly used therapeutic drugs. For example, in the aftermath of the Syrian civil war since 2011, millions have fled their homes to neighboring countries in the Middle East. The growing permanence of refugees and mass migrations is a call to shift our focus in the life sciences community from old models of pharmaceutical innovation. These seismic social changes demand faster decisions for "population-to-population bridging," whereby novel drugs developed in or for particular regions/countries can meet with rational regulatory decisions/approval in world regions impacted by migrant/refugee populations whose profiles are dynamic, such as in the Eastern Mediterranean region at present. Thus, it is important to characterize and report on the prevalence of pharmacogenes that affect commonly used medications and predict if population changes may call for attention to particular differences that may impact health of patients. Thus, we report here on four single-nucleotide polymorphism (SNP) variations in CYP2C9 and CYP2C19 genes among Mersin-Turkish healthy volunteers in the Mersin Province in the Eastern Mediterranean region that is currently hosting a vast number of migrant populations from Syria. Both CYP2C9 and CYP2C19 are very important pharmacogene molecular targets. We compare and report here on the observed SNP genetic variation in our sample with data on 12 world populations from dbSNP and discuss the feasibility of forecasting the pharmacokinetics of drugs utilized by migrant communities in Mersin and the Eastern Mediterranean region. This study can serve as a catalyst to invest in research in Syrian populations currently living in the Eastern Mediterranean. The findings have salience for rapid and rational regulatory decision-making for worldwide precision medicine and, specifically, "pharmacogenovigilance-guided bridging of pharmacokinetics" across world populations in the current era of planetary scale migration.

Modified sequential Helicobacter pylori eradication therapy using high dose omeprazole and amoxicillin in the initial phase in the extensive metaboliser Turkish patients for CYP2C19 polymorphism is ineffective.

AIM: To investigate whether the sequential therapy composed of high dose omeprazole and high dose amoxicillin in the first step was effective in eradication of H. pylori and whether there was a relation between effectiveness of the therapy and CYP2C19 gene polymorphism. METHOD: 134 dyspeptic patients with H. pylori were administered a modified sequential therapy composed of omeprazole 40 mg t.i.d. and amoxicillin 1000 mg t.i.d, for the first five days followed by omeprazole 20 mg b.d., metronidazole 500 mg t.i.d. and tetracycline 500 mg t.i.d, for the next five days. CYP2C19 genotype status was determined in patients. Hp eradication status was investigated by C14 UNT four weeks after treatment. RESULTS: The eradication rates were 64.9% in ITT and 74.3% in PP analysis. In subgroup analyses, eradication rates were 73.8% and 60.8% (p: 0.145) in ITT for peptic ulcer and non-ulcer dyspepsia patients respectively and 86.1% and 69.1% (p: 0.052) in PP analysis for peptic ulcer and non-ulcer dyspepsia patients respectively. The difference was not significant. As for the CYP2C19 gene status, 81.5% of the patients had HoEM and 17.3% of the patients had HeEM, and eradication rates were 72% and 75% in ITT analysis for HoEM and HeEM respectively (p: 0.803) and 73.9% and 85.7% in PP analysis for HoEM and HeEM respectively (p: 0.347). There was not a significant difference in H. pylori eradication rates between the two groups. CONCLUSION: This modified high-dose sequential therapy was ineffective in a Turkish sample, nearly all of whom had EM in terms of CYP2C19 gene status.

Label free DNA detection using large area graphene based field effect transistor biosensors.

We describe the fabrication of highly sensitive graphene based field effect transistor (FET) biosensors with a cost-effective approach and their application in label-free Deoxyribonucleic acid (DNA) detection. Chemical vapor deposition (CVD) grown graphene layers were used to achieve mass production of FET devices via conventional photolithographic patterning. Non-covalent functionalization of the graphene layer with 1-Pyrenebutanoic acid succinimidyl ester ensures high conductivity and sensitivity of the FET device. The present device could reach a detection limit as low as 3 x 10(-9) M.