2 × 4†kW near-single-mode laser output assisted by an optimized bidirectional oscillating-amplifying integrated fiber laser configuration.

Bidirectional output oscillating-amplifying integrated fiber laser (B-OAIFL) can achieve the two-ports laser amplification based on a single cavity, showcasing a promising prospect. In order to improve both the laser power and beam quality, we first simulate and optimize the stimulated Raman scattering (SRS) effect in the B-OAIFL. The simulation results show the SRS effect can be suppressed by optimizing the diameter as well as the length of the active fiber at different locations. With the guidance of theoretical and experimental analysis for the combined suppression of SRS and transverse mode instability (TMI), a near-single-mode B-OAIFL with 2 × 4 kW was demonstrated. Based on this foundation, we further devoted ourselves to the pursuit of the optimization of the structure and performance. The necessity of the configuration of side pump, which was initially introduced for its exceptional performance in stabilizing temporal chaos, was reevaluated in detail. With its negative impacts on efficiency improvement and SRS suppression were analyzed and verified, we removed this configuration and finally demonstrated a more simplified design with superior performance. A total bidirectional output of 8105 W was achieved, with an O-O efficiency of 79.6% and a near-single-mode beam quality of M A 2∼1.36,M B 2∼1.63. No signs of TMI were observed, and the signal-to-SRS suppression ratio was over 38 dB. The results still demonstrate a promising potential for power scaling based on this configuration and parameters.

Novel Bidirectional Output Ytterbium-Doped High Power Fiber Lasers: From Continuous to Quasi-Continuous.

Traditional ytterbium-doped high-power fiber lasers generally use a unidirectional output structure. To reduce the cost and improve the efficiency of the fiber laser, we propose a bidirectional output fiber laser (BOFL). The BOFL has many advantages over that of the traditional unidirectional output fiber laser (UOFL) and has a wide application in the industrial field. In theory, the model of the BOFL is established, and a comparison of the nonlinear effect in the traditional UOFL and the BOFL is studied. Experimentally, high-power continuous wave (CW) and quasi-continuous wave (QCW) BOFLs are demonstrated. In the continuous laser, we first combine the BOFL with the oscillating amplifying integrated structure, and a near-single-mode bidirectional 2 × 4 kW output with a total power of above 8 kW is demonstrated. Then, with the simple BOFL, a CW bidirectional 2 × 5 kW output with a total power of above 10 kW is demonstrated. By means of pump source modulation, a QCW BOFL is developed, and the output of a near-single mode QCW laser with a peak output of 2 × 4.5 kW with a total peak power of more than 9 kW is realized. Both CW and QCW output BOFL are the highest powers reported at present.

2 × 4.5 kW bidirectional output near-single-mode quasi-continuous wave monolithic fiber laser.

Quasi-continuous wave (QCW) laser has a very broad application in the industrial field, especially in additive manufacturing, surface treatment, laser cutting, laser cleaning, and laser drilling. Compared with the unidirectional fiber laser, the bidirectional output can be achieved two ports high power output with only one resonator, which can greatly reduce the industrial cost. However, there are few researches on QCW fiber lasers with bidirectional output. Here, we optimized and demonstrated a bidirectional output QCW laser with output power of 2 × 4.5 kW based on a double-clad ytterbium-doped fiber with a core/cladding diameter of 25/400 µm. The peak power at both ends reached 4515 W and 4694 W, respectively. The Raman suppression ratio at both ends of A and B is about 12 dB, and the beam quality factor M2 is about 1.37 and 1.42, respectively. The corresponding optical-to-optical efficiency is 79%. To the best of our knowledge, this is the highest peak power of QCW laser with near-single-mode beam quality in a bidirectional structure laser.

Demonstration of 3kW × 2 ports bidirectional output oscillating-amplifying integrated fiber laser employing chirped and tilted fiber Bragg gratings for co-SRS suppression.

Bidirectional output oscillating-amplifying integrated fiber laser (B-OAIFL) is a newly developed configuration with many advantages like compactness and good reliability. In this work, a B-OAIFL with a low time-stabilized threshold was constructed by employing a pair of side pump/signal combiner in the oscillating section, which demonstrates smooth temporal characteristics with no pulse detected by the photodetector at the output power level of only a few of tens Watts. We investigated the effect of side pumping on the Raman Stokes light and verified its contribution to mitigating the temporal-chaos-induced stimulated Raman scattering (SRS). The phenomenon of co-SRS caused by the mutual excitation of backward Stokes light from two amplifying sections under bidirectional pumping was first reported and studied. A pair of chirped and tilted fiber Bragg gratings (CTFBGs) were applied between the oscillating and amplifying sections to suppress the co-SRS, and the effect of the number of CTFBGs on the suppression of co-SRS was studied in detail experimentally. Finally, we successfully suppressed the co-SRS, and achieved a 3kW × 2 ports laser output, with a near-single-mode beam quality of M A 2∼1.3,M B 2∼1.4. In contrast, without the use of CTFBG, only a 2 kW-level output was obtained from each port, limited by co-SRS (with an SRS suppression ratio of less than 15 dB). The maximum output power of end A and end B is 3133 W and 3213 W, with the SRS suppression ratio of about 27.6 dB and 28.1 dB, respectively. No TMI features were observed under bidirectional pumping. The results demonstrate a significant potential for further power scaling based on this configuration. To the best of our knowledge, it is the highest output power achieved based on the B-OAIFL.

Origin of SRS-induced beam quality distortion under TMI threshold.

In high power fiber lasers, the degradation of beam quality caused by Raman effect has attracted more and more attention in recent years, but its physical mechanism is still unclear. We're going to differentiate between heat effect and nonlinear effect by duty cycle operation. The evolution of beam quality at different pump duty cycles has been studied based on a quasi-continuous wave (QCW) fiber laser. It is found that even if the Stokes intensity is only -6 dB (energy proportion: 26%) lower than that of the signal light intensity, the beam quality has no obvious change with the duty cycle of 5%; on the contrary, when the duty cycle gradually approaches 100% (CW-pumped scheme), the beam quality distortion changes faster and faster with the increase of Stokes intensity. The experimental results are contrary to core-pumped Raman effect theory [IEEE Photon. Technol. Lett.34, 215 (2022)10.1109/LPT.2022.3148999], and further analysis confirms that the heat accumulation in the process of Stokes frequency shift should be responsible for this phenomenon. That is the first time, to the best of our knowledge, for intuitive reveal of the origin of stimulated Raman scattering (SRS)-induced beam quality distortion under transverse mode instability (TMI) threshold in an experiment.

Demonstration of the reliability of a 5-kW-level oscillating-amplifying integrated fiber laser.

A novel fiber laser called an oscillating-amplifying integrated fiber laser was studied experimentally, in which the oscillating section and amplifying section share the pump between them. Based on this configuration, a 5-kW fiber laser system with optical-optical efficiency of 80.9% and M2 factor of 1.5 was achieved. The startup and shutdown sequence of the laser was studied in detail. When pumps of the laser were deliberately turned on in an inverted order, such as switching on/off the amplifying section before/after the oscillating section, which is normally disastrous in a classic fiber amplifier, the laser system turned out to operate stably at full power level. Thus, it is verified that there is no priority between the amplifier and the seed in this laser system. It combines the advantages of conventional fiber oscillators and fiber amplifiers, including high efficiency, high reliability, good anti-backreflection, and simple control logic.

5 kW monolithic fiber amplifier employing homemade spindle-shaped ytterbium-doped fiber.

We have demonstrated a 5 kW high-power monolithic fiber amplifier employing a homemade spindle-shaped ytterbium-doped fiber (YDF) based on the main oscillator power amplifier configuration. The YDF consists of a spindle-shaped core and cladding along the fiber length, with a core/cladding diameter of 27/410 µm at both ends and 39.5/600 µm in the middle. An output power of over 5 kW and beam quality of about 1.9 and an optical-to-optical conversion efficiency of 66.6% were achieved in the amplifier under a bidirectional pump scheme. While operating at the maximum power, the laser performance was evaluated, and the transverse mode instability and stimulated Raman scattering effects were well mitigated. To the best of our knowledge, this is the highest power demonstration in a continuous-wave fiber laser employing a tapered fiber. Further power scaling is promising by optimizing the structure of the YDF.

Near-single-mode 3 kW monolithic fiber oscillator based on a longitudinally spindle-shaped Yb-doped fiber: publisher's note.

This publisher's note contains corrections to Opt. Lett.45, 5792 (2020)OPLEDP0146-959210.1364/OL.404893.

Near-single-mode 3 kW monolithic fiber oscillator based on a longitudinally spindle-shaped Yb-doped fiber.

In order to balance the mitigation of transverse mode instability and stimulated Raman scattering effect in the high power fiber lasers, a specially designed Yb-doped fiber, named spindle-shaped Yb-doped fiber, was fabricated with a core/cladding diameter of 20/400 µm at both ends and 30/600 µm in the middle. Based on this fiber, an all-fiber laser oscillator was built and over 3 kW near-single-mode (M2 factor ∼1.3) laser was achieved with an optical-to-optical conversion efficiency of 78.4%. While operating at the maximum power, the transverse mode instability is well mitigated and the stimulated Raman scattering effect is well suppressed (>34dB lower than signal laser). Further power scaling is promising by optimizing the structure of the Yb-doped fiber.