Chitosan-induced biomodification on demineralized dentin to improve the adhesive interface.

Objectives: Metalloproteinase-inhibiting agents, such as chitosan, can prevent collagen degradation in demineralized dental substrates, thereby improving the adhesive interface. This study evaluated the bond strength (BS) and chemical and morphological characterization of the adhesive interface after applying chitosan solution to demineralized dentin. Materials and Methods: The 80 third molars were selected. Forty teeth underwent caries induction using the pH cycling method. The teeth were divided according to the treatment: distilled water (control) and 2.5% chitosan solution. The surfaces were restored using adhesive and composite resins. Half of the specimens in each group were aged, and the other half underwent immediate analyses. The teeth were sectioned and underwent the microtensile bond strength test (µTBS), and chemical and morphological analyses using energy-dispersive spectroscopy and scanning electron microscopy, respectively. Data analysis was performed using 3-way analysis of variance. Results: For µTBS, sound dentin was superior to demineralized dentin (p < 0.001), chitosan-treated specimens had higher bond strength than the untreated ones (p < 0.001), and those that underwent immediate analysis had higher values than the aged specimens (p = 0.019). No significant differences were observed in the chemical or morphological compositions. Conclusions: Chitosan treatment improved bond strength both immediately and after aging, even in demineralized dentin.

Chitosan improves the durability of resin-dentin interface with etch-and-rinse or self-etch adhesive systems.

OBJECTIVE: Degradation of the dentin-resin interface can occur due to hydrolysis of exposed collagen, resulting in reduced bond strength. This study assessed the effect of dentin treatment with chitosan combined with an etch-and-rinse or self-etch adhesive system on improvement of bond strength and preservation of the interface durability. METHODOLOGY: Enamel was removed from 80 molars and the teeth were divided into two groups: without chitosan (control) or with 2.5% chitosan gel (1 min). They were further subdivided into two subgroups according to the adhesive system: etch-and-rinse or self-etch. Dentin was restored using a composite resin. Half of the specimens from each restored group were subjected to interface aging and the remaining specimens were used for immediate analysis. The specimens were sectioned and subjected to microtensile bond strength (µTBS) test (n=10), chemical composition testing using Fourier-transform infrared (FTIR) spectroscopy (n=4) and energy-dispersive spectroscopy (EDS) (n=5), and morphological analysis of the adhesive interface using scanning electron microscopy (SEM) (n=5). Data were analyzed using three-way ANOVA. RESULTS: Chitosan improved the µTBS of the adhesive interface when compared with the control group (p=0.004). No significant differences were observed in dentin adhesion between the adhesive systems (p=0.652). Immediate µTBS was not significantly different from that after 6 months (p=0.274). EDS and SEM did not show significant differences in the chemical and structural composition of the specimens. FTIR showed a decrease in the intensity of phosphate and carbonate bands after using chitosan. CONCLUSIONS: Dentin treatment with chitosan combined with an etch-and-rinse or self-etch adhesive system improved the immediate and preserved the 6-month bond strength of the adhesive interface.

Protocols for sodium ascorbate application on intracoronary dentin bleached with high-concentrated agent.

PURPOSE: Composite resin restorations are normally replaced after the internal bleaching of endodontically treated-teeth because the bleaching agent does not alter the color of the restorative material. This study evaluated the effect of 10% sodium ascorbate (SA) applied at different protocols on bleached dentin. MATERIALS AND METHODS: One-hundred slabs of intracoronary bovine dentin were divided into 5 groups: 2 controls-GI without bleaching (positive), GII bleached with 35% hydrogen peroxide (HP) (negative); and 3 experimentals - GIII. 35% HP + SA at protocol 1 (dripping, washing and drying the solution), GIV. 35% HP + SA at protocol 2 (dripping and aspirating the solution) and GV. 35% HP + SA at protocol 3 (dripping, rubbing and aspirating the solution). Sixty fragments were restored and subjected to shear bond strength test (n = 12). Forty fragments (n = 8) were prepared for chemical analysis (energy dispersive X-ray spectrometry) and surface morphology (scanning electron microscopy). Data were analyzed by ANOVA and Tukey test (P < 0.05). RESULTS: GI (3.169 ± 1.510a) had the highest means values, similar to GIV (2.752 ± 0.961a) and GV (2.981 ± 1.185a) (P < 0.05). Inferior values were obtained in GII (1.472 ± 0.342b) and GIII (2.037 ± 0.742ab) had intermediate values (P > 0.05). Oxygen concentration was reduced in groups treated with SA, and the surface exhibited residual granules of the solution. CONCLUSION: The 10% SA solution reestablishes the bond strength of restorative material to bleached dentin, especially if active protocols of application and aspiration were used.