Microwave-Assisted Conversion of 5-Hydroxymethylfurfural into 2,5-Furandicarboxylic Acid over CuCo Oxide.

A series of CuCo bimetallic catalysts were prepared via the co-precipitation method for the catalytic transformation of biomass-derived 5-hydroxymethylfurfural (HMF) into 2,5-furandicarboxylic acid (FDCA). FDCA acts as a precursor for biodegradable biopolymer polyethylene furanoate production, thereby achieving a carbon-neutral approach. Out of all the synthesized catalysts, CuCo(1:1) showed remarkable catalytic activity and yielded 70.67% FDCA while achieving 100% HMF conversion in 5 minutes at 50 ℃ temperature in the presence of tert-butyl hydroperoxide as an oxidant. Synergistic effects of the catalyst, such as adsorbed oxygen, relative oxygen vacancy, lesser pore size, and pore volume, were key factors attributed to the catalyst's excellent activity. The synthesized catalyst showed good recyclability with a minimal decrease in FDCA yield up to 5 cycles. Pre and post-characterization of catalysts such as BET, TEM, FE-SEM, XRD, H2-TPR, CO2 TPD, ICP-OES, and XPS were done to correlate the catalyst's properties with its activity. In addition, the effect of reaction parameters such as stirring speed, temperature reaction time, catalyst weight, base, and oxidant was studied to achieve optimum reaction conditions. The reaction products were analyzed quantitatively and qualitatively using HPLC and HR-MS.

Bifunctional MoNi4/nickel foam electro-catalyst for ultra-efficient oxidation of high-concentration 5-hydroxymethylfurfural and HER.

The electro-catalytic oxidation of biomass-derived 5-hydroxymethylfurfural (HMF) provides an attractive route to produce 2, 5-furandicarboxylic acid (FDCA) as a substitute for terephthalic acid used in the plastics industry. Herein, we prepared MoNi4 alloy on nickel foam (NF) using a simple hydrothermal method followed by hydrogen reduction. Applied MoNi4/NF as the bifunctional electrodes for the electro-catalytic HMF oxidation reaction (HMFOR) and HER, 98.7% FDCA yield and 97.3% Faraday efficiency (FE) can be achieved even with HMF concentration as high as 200 mM. Notably, no obvious deactivation was observed after ten consecutive cycles. In-situ Raman, XANES and EXAFS results show that the nickel species of MoNi4/NF is first oxidized to Ni3+ species under the applied voltage, and after undergoing the electro-catalytic HMFOR, then reduced to Ni2-δ state (with a valence between 0 and +2) due to the electron-donating effect from Mo. MoNi4/NF with more than one electron transfer between Ni3+ and Ni2-δ during the HMFOR enables it to have excellent electro-catalytic oxidation ability toward HMFOR.

Non-noble metal catalysts for electrooxidation of 5-hydroxymethylfurfural.

2,5-Furandicarboxylic acid (FDCA) is a class of valuable biomass-based platform compounds. The creation of FDCA involves the catalytic oxidation of 5-hydroxymethylfurfural (HMF). As a novel catalytic method, electrocatalysis has been utilized in the 5-hydroxymethylfurfural oxidation reaction (HMFOR). Common noble metal catalysts show catalytic activity, which is limited by price and reaction conditions. Non-noble metal catalyst is known for its environmental friendliness, affordability and high efficiency. The development of energy efficient non-noble metal catalysts plays a crucial role in enhancing the HMFOR process. It can greatly upgrade the demand of industrial production, and has important research significance for electrocatalytic oxidation of HMF. In this paper, the reaction mechanism of HMF undergoes electrocatalytic oxidation to produce FDCA are elaborately summarized. There are two reaction pathways and two oxidation mechanisms of HMFOR discussed deeply. In addition, the speculation on the response of the electrode potential to HMFOR is presented in this paper. The main non-noble metal electrocatalysts currently used are classified and summarized by targeting metal element species. Finally, the paper focus on the mechanistic effects of non-noble metal catalysts in the reaction, and provide the present prospects and challenges in the electrocatalytic oxidation reaction of HMF.

Recent Advances in the Synthesis of 2-Furoic Acid and 2,5-Furandicarboxylic Acid from Furfural.

2,5-furandicarboxylic acid (FDCA) is an important organic platform compound that has been widely used in the fields of medicine, pesticides, dyes, plastics and resins due to its unique structure and properties. In recent years, with the emphasis on sustainable development and green chemistry, the synthesis of FDCA from biomass has attracted extensive attention. The catalytic conversion of furfural (FF) to FDCA has the advantages of easy availability of the raw material, environmental friendliness, economic feasibility and so on, which is an important direction for FDCA synthesis in the future. This paper mainly reviews the prepare pathways of furoic acid (FA) and FDCA using FF as a starting material, including the selective conversion of FF and FA to target products under different types of catalysts. First, the research progress in the synthesis of FA from FF was summarized, and then the advances in the catalytic conversion of FA to FDCA was reviewed. In addition, the development of efficient and green catalysts and the optimization of existing synthesis protocols are emphasized as key factors to improve the yield and purity of FDCA while reducing production costs. Finally, the opportunities and challenges were discussed.

One-pot, Solvent Free Synthesis of 2,5-Furandicarboxylic Acid from Deep Eutectic Mixtures of Sugars as Mediated by Bifunctional Catalyst.

Currently one-pot conversion of sugars to 2,5-furandicarboxylic acid (FDCA) is of significant interest due to the attainability of sugars as a feedstock and the enormous potential of FDCA as a bioplastic monomer. However, it remains challenging to construct efficient catalysts for this process. In this study, Co3O4 species were anchored to a sulfonated covalent organic framework thus affording a bifunctional catalyst (Co3O4@COF-SO3H). The sulfonic acid sites dehydrate sugars to 5-hydroxymethylfurfural (HMF), which is next oxidized to FDCA as catalyzed by the Co3O4 species. Such a process was applied in the conversion of various binary and ternary deep eutectic mixtures involving choline chloride and sugars without additional solvent. The maximum FDCA yield of 84% was obtained using glucose-fructose eutectic mixture as the substrates. Moreover, the catalyst was recyclable and stable under the applied reaction conditions. Our process eliminates the employment of organic solvents and expensive noble metal catalysts, resulting in green and economic biomass conversions.

Co@NC Chainmail Nanowires for Thermo- and Electrocatalytic Oxidation of 2,5-Bis(hydroxymethyl)furan to 2,5-Furandicarboxylic Acid.

2,5-Furandicarboxylic acid (FDCA) has emerged as an important bio-based furanic compound, which has broad application prospects in renewable energy and materials, especially in the preparation of polyethylene 2,5-furandicarboxylate (PEF). While the  conventional synthesis of FDCA involves oxidation of 5-hydroxymethylfurfural (HMF) as a substitute, the thermal and chemical instability of HMF due to its aldehyde group poses challenges. A more favorable alternative is the utilization of 2,5-bis(hydroxymethyl)furan (BHMF), a non-aldehyde and more stable precursor. This study pioneeringly reports nitrogen-doped-carbon encapsulated cobalt (Co@NC) chainmail nanowires for the thermal and electrocatalytic oxidation of BHMF to FDCA. The Co@NC/NF achieved a 97.9% conversion of BHMF with a 93.3% yield of FDCA  at 1.475 V vs. RHE, whereas thermal catalysis only obtained 14.9% FDCA yield after 10 hours. Kinetic studies indicated that the large electrochemically active surface area and excellent kinetic parameters contribute its superior electrochemical performance. Mechanistic analysis revealed that the migration of inner electrons to the exterior modified the electronic properties of the carbon layer, thereby facilitating the oxidation of BHMF. Furthermore, the in-situ generation of high-valent cobalt species markedly accelerated the BHMF oxidation. This research underscores the potential of carbon-encapsulated metal chainmail catalysts in thermal and electrochemical biomass conversion.

Optimization of operating parameters for 2,5-furandicarboxylic acid recovery using electrodialysis with bipolar membrane and traditional electrodialysis systems.

Electrodialysis (ED) is an eco-friendly and feasible method to separate or recover ionic compounds by electric field attraction and configuration of ion exchange membranes. Strain Burkholderia sp. H-2 could biotransform 5-hydroxymethylfurfural (5-HMF) into a green platform compound, 2,5-furandicarboxylic acid (FDCA), using a bioreactor system. In this study, electrodialysis with the bipolar membrane (EDBM) and traditional ED systems were applied to recover and concentrate FDCA. Artificial and real FDCA effluents of the 5-HMF biotransformation bioreactor were used as the feedstock to establish the optimal conditions for FDCA recovery. The optimal FDCA concentration and pH of the artificial FDCA effluent were 2100 mg/L and 5, respectively. The suitable current density of the EDBM was 8.93 mA/cm2. For FDCA recovery and concentration using the ED, the feedstock volume and FDCA concentration in the concentration chamber were 1.5 L and 1000 mg/L, respectively. The FDCA recovery efficiency of the real FDCA effluent was 55.6 %. Suppose the pretreatment procedure of the real bioreactor effluent is further optimized. It is believed to benefit the enhancement of FDCA recovery efficiency and reduce energy consumption.

Base-Free Oxidation of HMF to FDCA over Ru/Cu-Co-O·MgO under Aqueous Conditions.

The copper-cobalt metal oxide composite magnesium oxide catalyst loaded with Ru has achieved the aerobic oxidation of 5-hydroxymethylfurfural (HMF) to the bio-based polyester monomer 2,5-furandicarboxylic acid (FDCA) under base-free conditions. Several Ru/Cu-Co-O·MgO catalysts were prepared, with Cu-Co-O being a combination of CuO and Co3O4. The catalyst's activity was boosted by the synergistic interaction between copper and cobalt, as well as an optimal copper-to-cobalt molar ratio. Optimal catalytic activity was observed in the Ru4/Cu1-Co1-O·MgO catalyst, loaded with 4 wt% Ru when copper-to-cobalt molar ratio of 1:1 and magnesium oxide compounding amount of 6 mmol were employed. The inclusion of MgO and the load of Ru not only expanded the specific surface area of the catalyst but also heightened its basicity. Additionally, the presence of loaded Ru improved the catalyst's reducibility at low temperatures. In aqueous solution under oxygen pressure, the conversion rate of HMF achieved 100%, and the yield of FDCA was 86.1%. After five reaction cycles, examining the catalyst and solution revealed that Ru nanoparticles resisted leaching or oxidation, and MgO exhibited only slight dissolution. The green separation of the product was achieved using semi-preparative liquid chromatography, selectively collecting the FDCA-containing solution by exploiting variations in interactions between solutes and the stationary/mobile phases. The subsequent steps involved rotary evaporation and drying, resulting in FDCA powder with a purity exceeding 99%. Notably, this approach eliminated the need to introduce concentrated hydrochloric acid into the system for FDCA separation, providing a novel method for synthesising powdered FDCA.

Multistep Biooxidation of 5-(Hydroxymethyl)furfural to 2,5-Furandicarboxylic Acid with H2O2 by Unspecific Peroxygenases.

5-(Hydroxymethyl)furfural (HMF) is a key platform chemical derived from renewable biomass sources, holding great potential as starting material for the synthesis of valuable compounds, thereby replacing petrochemical-derived counterparts. Among these valorised compounds, 2,5-furandicarboxylic acid (FDCA) has emerged as a versatile building block. Here we demonstrate the biocatalytic synthesis of FDCA from HMF via a one-pot three-step oxidative cascade performed via two operative steps under mild reaction conditions employing two unspecific peroxygenases (UPOs) using hydrogen peroxide as the only oxidant. The challenge of HMF oxidation by UPOs is the chemoselectivity of the first step, as one of the two possible oxidation products is only a poor substrate for further oxidation. The unspecific peroxygenase from Marasmius oreades (MorUPO) was found to oxidize 100 mM of HMF to 5-formyl-2-furoic acid (FFCA) with 95 % chemoselectivity. In the sequential one-pot cascade employing MorUPO (TON up to 13535) and the UPO from Agrocybe aegerita (AaeUPO, TON up to 7079), 100 mM of HMF were oxidized to FDCA reaching up to 99 % conversion and yielding 861 mg isolated pure crystalline FDCA, presenting the first example of a gram scale biocatalytic synthesis of FDCA involving UPOs.

Highly Effective Non-Noble MnO2 Catalysts for 5-Hydroxymethylfurfural Oxidation to 2,5-Furandicarboxylic Acid.

Noble metal-free catalyst or catalytic oxidation of 5-hydroxymethylfurfural into 2,5-furandicarboxylic acid are proposed in this study as a proposal to solve one of the great disadvantages of this reaction of using preferably noble metal-based catalysts. The catalytic activity of six MnO2 crystal structures is studied as alternative. The obtained results showed a strong connection between catalytic activity the type of MnO2 structure organization and redox behavior. Among all tested catalysts, ϵ-MnO2 showed the best performance with an excellent yield of 74 % of 2,5-furandicarboxylic acid at full -hydroxymethylfurfural conversion.

Ultra-Dense Supported Ruthenium Oxide Clusters via Directed Ion Exchange for Efficient Valorization of 5-Hydroxymethylfurfural.

Maximizing the loadings of active centers without aggregation for a supported catalyst is a grand challenge but essential for achieving high gravimetric catalytic activity, especially toward multi-step reactions. The oxidation of 5-hydroxymethylfurfural (HMF), a key biomass-derived platform molecule, into 2,5-furandicarboxylic acid (FDCA), a promising alternative to polyester monomer, is such a multi-step reaction that involves 6 proton and electron transfers. This process often demands strong alkaline environment but also suffers from the alkali-driven polymerization side-reaction. Meanwhile, neutral media ameliorates the polymerization, but lacks efficient catalyst toward deep oxidation. Herein, we devised a strategy of creating ultra-dense supported Ru oxide clusters via directed ion exchange in a Co hydroxyanion (CoHA) support material. Pyrimidine ligands were first incorporated into the CoHA interlayers, and the subsequent evacuation of pyrimidines created porous channels for the directed ion exchange with the built-in anions in CoHA, which allowed the dense and mono-disperse functionalization of RuCl6 2- anions and their resulting Ru oxide clusters. These ultra-dense Ru oxide clusters not only enable high HMF electrooxidation currents under neutral conditions but also create microscopic channels in-between the clusters for the expedited re-adsorption and oxidation of intermediates toward highly oxidized product, such as 5-formyl-2-furoic acid (FFCA) and FDCA. A two-stage HMF oxidation process, consisting of ambient conversion of HMF into FFCA and FFCA oxidation into FDCA under 60 °C, was eventually developed to first achieve a high FDCA yield of 92.1 % under neutral media with significantly reduced polymerization.

Electron Structure Tuned Oxygen Vacancy-Rich AuPd/CeO2 for Enhancing 5-Hydroxymethylfurfural Oxidation.

The design of high activity catalyst for the efficiently conversion of 5-hydroxymethylfurfural (HMF) to 2,5-furandicarboxylic acid (FDCA) gains great interest. The rationally tailoring of electronic structure directly affects the interaction between catalysts and organic substrates, especially molecular oxygen as the oxidant. This work, the bimetallic catalysts AuPd/CeO2 were prepared by the combining method of chemical reduction and photo-deposition, effectively concerting charge between Au and Pd and forming the electron-rich state of Au. The increasing of oxygen vacancy concentration of CeO2 by acidic treatment can facilitate the adsorption of HMF for catalysts and enhance the yield of FDCA (99.0 %). Moreover, a series of experiment results combining with density functional theory calculation illustrated that the oxidation performance of catalyst in HMF conversion was strongly related to the electronic state of interfacial Au-Pd-CeO2. Furthermore, the electron-rich state sites strengthen the adsorption and activation of molecular oxygen, greatly promoting the elimination of ß-hydride for the selective oxidation of 5-hydroxymethyl-2-furancarboxylic acid (HMFCA) to FDCA, accompanied with an outgoing FDCA formation rate of 13.21 mmol ⋅ g-1 ⋅ min-1 at 80 °C. The perception exhibited in this research could be benefit to understanding the effects of electronic state for interfacial sites and designing excellent catalysts for the oxidation of HMF.

Crosslinked Polyesters as Fully Biobased Coatings with Cutin Monomer from Tomato Peel Wastes.

Cutin, one of the main structural components of tomato peels, is a waxy biopolymer rich in hydroxylated fatty acids. In this study, 10,16-dihydroxyhexadecanoic acid (10,16-diHHDA) was extracted and isolated from tomato peels and exploited to develop fully crosslinked polyesters as potential candidates for replacing fossil-based metal protective coatings. A preliminary screening was conducted to select the base formulation, and then a design of experiments (DoE) was used as a methodology to identify the optimal composition to develop a suitable coating material. Different formulations containing 10,16-diHHDA and other biorefinery monomers, including 2,5-furandicarboxylic acid, were considered. To this end, all polyesters were characterized through differential scanning calorimetry (DSC) and gel content measurements to determine their Tg value and crosslinking efficiency. Compositions exhibiting the best trade-off between Tg value, chemical resistance, and sufficiently high 10,16-diHHDA content between 39 and 48 wt.% were used to prepare model coatings that were characterized for assessing their wettability, scratch hardness, chemical resistance, and adhesion to metal substrates. These polyester coatings showed a Tg in the range of 45-55 °C, a hydrophobic behavior with a water contact angle of around 100°, a good solvent resistance (>100 MEK double rubs), and an adhesion strength to steel higher than 2 MPa. The results obtained confirmed the potential of cutin-based resins as coatings for metal protection, meeting the requirements for ensuring physicochemical properties of the final product, as well as for optimizing the valorization of such an abundant agri-food waste as tomato peels.

Identification of redox activators for continuous reactivation of glyoxal oxidase from Trametes versicolor in a two-enzyme reaction cascade.

Glyoxal oxidases, belonging to the group of copper radical oxidases (CROs), oxidize aldehydes to carboxylic acids, while reducing O2 to H2O2. Their activity on furan derivatives like 5-hydroxymethylfurfural (HMF) makes these enzymes promising biocatalysts for the environmentally friendly synthesis of the bioplastics precursor 2,5-furandicarboxylic acid (FDCA). However, glyoxal oxidases suffer from inactivation, which requires the identification of suitable redox activators for efficient substrate conversion. Furthermore, only a few glyoxal oxidases have been expressed and characterized so far. Here, we report on a new glyoxal oxidase from Trametes versicolor (TvGLOX) that was expressed at high levels in Pichia pastoris (reclassified as Komagataella phaffii). TvGLOX was found to catalyze the oxidation of aldehyde groups in glyoxylic acid, methyl glyoxal, HMF, 2,5-diformylfuran (DFF) and 5-formyl-2-furancarboxylic acid (FFCA), but barely accepted alcohol groups as in 5-hydroxymethyl-2-furancarboxylic acid (HMFCA), preventing formation of FDCA from HMF. Various redox activators were tested for TvGLOX reactivation during catalyzed reactions. Among them, a combination of horseradish peroxidase and its substrate 2,2'-azino-di-(3-ethylbenzthiazoline sulfonic acid) (ABTS) most efficiently reactivated TvGLOX. Through continuous reactivation of TvGLOX in a two-enzyme system employing a recombinant Moesziomyces antarcticus aryl-alcohol oxidase (MaAAO) almost complete conversion of 8 mM HMF to FDCA was achieved within 24 h.

-COOH & -OH Condensation Reaction Utilization for Biomass FDCA-based Polyesters.

A green and sustainable -COOH & -OH condensation solution polymerization method was hereby reported for FDCA-based polyesters to avoid discoloration and toxic solvents. First, taking poly(ethylene 2,5-furandicarboxylate) (PEF) as the representative of FDCA-based polyester, enabling good white appearance PEF with Mn=6.51×103 g mol-1 from FDCA and ethylene glycol in green solvent γ-valerolactone (GVL), catalyzed by 4-dimethylaminopyridine (DMAP) and N-(3-dimethylaminopropyl)-N'-ethylcarbodiimide hydrochloride (EDC). Additionally, the molecular weight of PEF was rapidly improved (Mn >2.5×104 g mol-1) via remelting polycondensation within minutes, with the dispersity still kept relatively low dispersity (D<1.40). Importantly, the -COOH & -OH condensation solution polymerization method was successfully applied for the synthesis of various FDCA-based polyesters, including diols with varying carbon chain lengths (3 to 11 carbons) and cycloalkyl diols, especially the applicability of this method to diols containing C=C double bonds, which was found to exhibit low heat resistance. Lastly, assisting with 13C labeled 1,4-succinic acid and in-situ 13C-NMR, an in-depth study of the possible catalytic mechanism was proposed, by which, EDC activated FDCA, and then DMAP catalyzed it with diol to yield macromolecular chain of polyester. Overall, the results provided a green and sustainable strategy for the synthesis of FDCA-based polyesters.

Enhancing Low-Potential Electrosynthesis of 2,5-Furandicarboxylic Acid on Monolithic CuO by Constructing Oxygen Vacancies.

Electrosynthesis of 2,5-furandicarboxylic acid (FDCA) from the biomass-derived 5-hydroxymethylfurfural (HMF) is one of the most potential means to produce a bioplastic monomer. Copper oxide (CuO) catalyst shows promising prospects due to its high surface activity, conductivity, and stability, but relatively poor capability of oxygen evolution; however, the weak adsorption of substrates and the lack of facile synthetic strategies largely restrict its practical application. Here, a novel facile in situ method, alternate cycle voltammetry (denoted as c) and potentiostatic electrolysis (denoted as p), was proposed to prepare a monolithic cpc-CuO/Cu-foam electrocatalyst. Along with the increment of CuO and its surficial oxygen vacancies (OV), the FDCA yield, productivity, and Faradaic efficiency can reach up to ∼98.5%, ∼0.2 mmol/cm2, and ∼94.5% under low potential of 1.404 VRHE. Such an efficient electrosynthesis system can be easily scaled up to afford pure FDCA powders. In a combinatory analysis via electron paramagnetic resonance spectroscopy, H2 temperature-programmed reduction, open circuit potential, infrared spectroscopy, zeta potential, electrochemical measurement, and theoretical calculation, we found that the CuO was the active phase and OV generated on CuO surface can dramatically enhance the adsorption of *HMF and *OH (* denotes an active site), accounting for its superior FDCA production. This work offers an excellent paradigm for enhancing biomass valorization on CuO catalysts by constructing surficial defects.

Fluorine Induced In Situ Formation of High Valent Nickel Species for Ultra Low Potential Electrooxidation of 5-Hydroxymethylfurfural.

The Nickel-based catalysts have a good catalytic effect on the 5-hydroxymethylfurfural electrooxidation reaction (HMFOR), but limited by the conversion potential of Ni2+ /Ni3+ , 1.35 V versus RHE, the HMF electrooxidation potential of nickel-based catalysts is generally greater than 1.35 V versus RHE. Considering fluorine has the highest Pauling electronegativity and similar atomic radius of oxygen, the introduction of fluorine into the lattice of metal oxides might promote the adsorption of intermediate species, thus improving the catalytic performance. F is successfully doped into the lattice structure of NiCo2 O4 spinel oxide by the strategy of hydrothermal reaction and low-temperature fluorination. As is confirmed by in situ electrochemical impedance spectroscopy and Raman spectroscopy, the introduction of F weakens the interaction force of metal-oxygen covalent bonds of the asymmetric MT -O-MO backbone and improves the valence of Ni in tetrahedra structure, which makes it easier to be oxidized to higher valence active Ni3+ under the action of electric field and promotes the adsorption of OH- , while the decrease of Co valence enhances the adsorption of HMF with the catalyst. Combining the above reasons, F-NiCo2 O4 shows superb electrocatalytic performance with a potential of only 1.297 V versus RHE at a current density of 20 mA cm-2 , which is lower than the most catalyst.

A Facile Synthesis Route to AuPd Alloys for the Selective Oxidation of 5-Hydroxymethylfurfural to 2,5-Furandicarboxylic Acid.

Synthesis of 2,5-furandicarboxylic acid (FDCA) can be achieved via catalytic oxidation of 5-hydroxymethylfurfural (5-HMF), in which both base and catalyst play important roles. This work presents the development of a simple synthesis method (based on a commercial parent 10 wt.% Pd/C catalyst) to prepare the bimetallic AuPd alloy catalysts (i. e., AuPd/C) for selective 5-HMF oxidation to FDCA. When using the strong base of NaOH, Pd and Au cooperate to promote FDCA formation when deployed either separately (as a physical mixture of the monometallic Au/C and Pd/C catalysts) or ideally alloyed (AuPd/C), with complete 5-HMF conversion and FDCA yields of 66 % vs 77 %, respectively. However, NaOH also promoted the formation of undesired by-products, leading to poor mass balances (<81 %). Comparatively, under weak base conditions (using NaHCO3 ), an increase in Au loading in the AuPd/C catalysts enhances 5-HMF conversion and FDCA productivity (due to the enhanced carbonyl oxidation capacity) which coincides with a superior mass balances of >97 %. Yet, the excessive Pd content in the AuPd/C catalysts was not beneficial in promoting FDCA formation.

Furan-based fluorescent probe free radical capture membrane: Analysis of RO2 radical composition and transformation mechanism in urban atmosphere.

Peroxyl radicals (RO2) are important components of atmospheric radical cycling and generation, but their formation, distribution and evolution mechanisms in the atmospheric environment have not been investigated. In this paper, we propose a novel atmospheric RO2 radical trapping membrane that can trap low carbon number (Rc ≤ 5) RO2 radicals and identify their R-group structures by fluorescence spectroscopy and chromatography. We also analyzed the composition and evolution mechanism of RO2 species under different meteorological conditions in the atmospheric environment of Lanzhou, China, to provide scientific support for the treatment and research of atmospheric chemical pollution.

Engineering 5-hydroxymethylfurfural (HMF) oxidation in Pseudomonas boosts tolerance and accelerates 2,5-furandicarboxylic acid (FDCA) production.

Due to its tolerance properties, Pseudomonas has gained particular interest as host for oxidative upgrading of the toxic aldehyde 5-hydroxymethylfurfural (HMF) into 2,5-furandicarboxylic acid (FDCA), a promising biobased alternative to terephthalate in polyesters. However, until now, the native enzymes responsible for aldehyde oxidation are unknown. Here, we report the identification of the primary HMF-converting enzymes of P. taiwanensis VLB120 and P. putida KT2440 by extended gene deletions. The key players in HMF oxidation are a molybdenum-dependent periplasmic oxidoreductase and a cytoplasmic dehydrogenase. Deletion of the corresponding genes almost completely abolished HMF oxidation, leading instead to aldehyde reduction. In this context, two HMF-reducing dehydrogenases were also revealed. These discoveries enabled enhancement of Pseudomonas' furanic aldehyde oxidation machinery by genomic overexpression of the respective genes. The resulting BOX strains (Boosted OXidation) represent superior hosts for biotechnological synthesis of FDCA from HMF. The increased oxidation rates provide greatly elevated HMF tolerance, thus tackling one of the major drawbacks of whole-cell catalysis with this aldehyde. Furthermore, the ROX (Reduced OXidation) and ROAR (Reduced Oxidation And Reduction) deletion mutants offer a solid foundation for future development of Pseudomonads as biotechnological chassis notably for scenarios where rapid HMF conversion is undesirable.