RESUMO
Despite its potential as a clean power source to meet rising electricity demands, nuclear energy generates radioactive waste, including isotopes of iodine, that pose significant environmental and health risks. There is a growing demand to capture radioactive iodine and repurpose it effectively. However, achieving this dual functionality with a single material remains a significant challenge. This study explores phosphorus-based porous organic polymers (P-POPs) as probes for these dual functionalities. By employing 4-formyl(triphenyl)phosphine (BB1) and phenyl-1,4-diacetonitrile (BB2) under the Knoevenagel polycondensation method, P-POPs (PKPOPs) have been synthesized that exhibit a smooth spherical morphology, which efficiently captures and release iodine under ambient conditions, facilitating efficient transportation of molecular iodine. This novel approach aims to potentially transform nuclear waste into valuable organic feedstock via an iodination reaction. The innovative application of PKPOP has also been demonstrated for iodination reactions using ball mills and under continuous flow conditions, showcasing its potential for safer waste management and utilization.
RESUMO
The rising prospects of mechanochemically assisted syntheses hold promise for both academia and industry, yet they face challenges in understanding and, therefore, anticipating respective reaction kinetics. Particularly, dependencies based on variations in milling equipment remain little understood and globally overlooked. This study aims to address this issue by identifying critical parameters through kinematic models, facilitating the reproducibility of mechanochemical reactions across the most prominent mills in laboratory settings, namely planetary and mixer mills. Through a series of selected experiments replicating major classes of organic, organometallic, transition metal-catalyzed, and inorganic reactions from literature, we rationalize the independence of kinematic parameters on reaction kinetics when the accumulated energy criterion is met. As a step forward and to facilitate the practicability of our findings, we provide a freely accessible online tool that allows the calculation of respective energy parameters for different planetary and mixer mills. Our work advances the current understanding of mechanochemistry and lays the foundation for future rational exploration in this rapidly evolving field.
RESUMO
Limited attempts have been made previously to develop high-loading CBD inhalable powders, which are essential for high dose delivery. Therefore, this study aimed to develop and characterise inhalable powders with ≥ 95 % w/w CBD by wet ball milling. The effects of magnesium stearate (2 % and 5 %) and inhaler resistance (low-resistance and high-resistance RS01 inhalers) on aerosol performance were also compared. Wet ball milling produced CBD powders with > 50 % production yield. The milled particles showed irregular shapes. The powders were crystalline with minimal amorphous content, low residual solvent level (<1%), and low moisture sorption (<4%). Magnesium stearate improved both the emitted and fine particle fractions. The aerodynamic particle size distribution of the formulations differed between the low-resistance and high-resistance RS01 inhalers. The latter decreased throat deposition but increased inhaler retention. The dissolution profiles showed that all three formulations released CBD steadily and plateaued at 30 min. The best scenario was CBD with 5 % magnesium stearate dispersed from the high resistance RS01 inhaler, showing the highest FPF with the lowest throat deposition. This combination may be tested in vivo in the future to investigate its pharmacokinetic profile.
Assuntos
Canabidiol , Tamanho da Partícula , Pós , Ácidos Esteáricos , Administração por Inalação , Ácidos Esteáricos/química , Canabidiol/administração & dosagem , Canabidiol/química , Canabidiol/farmacocinética , Aerossóis , Inaladores de Pó Seco , Excipientes/química , Química Farmacêutica/métodos , Liberação Controlada de Fármacos , Nebulizadores e Vaporizadores , Composição de Medicamentos/métodos , SolubilidadeRESUMO
We report an idea for the synthesis of oligopeptides using a solvent-free ball milling approach. Our concept is inspired by block play, in which it is possible to construct different objects using segments (blocks) of different sizes and lengths. We prove that by having a library of short peptides and employing the ball mill mechanosynthesis (BMMS) method, peptides can be easily coupled to form different oligopeptides with the desired functional and biological properties. Optimizing the BMMS process we found that the best yields we obtained when TBTU and cesium carbonate were used as reagents. The role of Cs2CO3 in the coupling mechanism was followed on each stage of synthesis by 1H, 13C and 133Cs NMR employing Magic Angle Spinning (MAS) techniques. It was found that cesium carbonate acts not only as a base but is also responsible for the activation of substrates and intermediates. The unique information about the BMMS mechanism is based on the analysis of 2D NMR data. The power of BMMS is proved by the example of different peptide combinations, 2+2, 3+2, 4+2, 5+2 and 4+4. The tetra-, penta-, hexa-, hepta- and octapeptides obtained under this project were fully characterized by MS and NMR techniques.
Assuntos
Carbonatos , Césio , Oligopeptídeos , Césio/química , Carbonatos/química , Oligopeptídeos/química , Espectroscopia de Ressonância Magnética , Solventes/químicaRESUMO
In the present work, we report the development of a rapid, efficient, and solvent-free procedure for the N-methylation of secondary amines under mechanochemical conditions. After optimization of the milling parameters, a vibrational ball mill was used to synthesize 26 tertiary N-methylated amine derivatives in a short time of 20 min (30 Hz frequency) and high yields ranging from 78 to 95%. An exception was compounds having a hydroxyl group in their structure, for which a decrease in reaction efficiency was observed. During our research, we investigated alternate reaction selectivity occurring in compounds able to form ring closure products that are 3,4-dihydro-2H-1,3-benzoxazine derivatives instead of N-methylated products. The liquid-assisted grinding technique has been applied using formalin as a methylating agent and sodium triacetoxyborohydride as a reducing agent in a reductive amination reaction.
RESUMO
Chalcones are polyphenols that belong to the flavonoids family, known for their broad pharmacological properties. They have thus attracted the attention of chemists for their obtention and potential activities. In our study, a library of compounds from 2'-hydroxychalcone's family was first synthesized. A one-step mechanochemical synthesis via Claisen-Schmidt condensation reaction under ball mill conditions was studied, first in a model reaction between a 5'-fluoro-2'-hydroxyacetophenone and 3,4-dimethoxybenzaldehyde. The reaction was optimized in terms of catalysts, ratio of reagents, reaction time, and influence of additives. Among all assays, we retained the best one, which gave the highest yield of 96% when operating in the presence of 1 + 1 eq. of substituted benzaldehyde and 2 eq. of KOH under two grinding cycles of 30 min. Thus, this protocol was adopted for the synthesis of the selected library of 2'-hydroxychalcones derivatives. The biological activities of 17 compounds were then assessed against Plasmodium falciparum, Leishmania donovani parasite development, as well as IGR-39 melanoma cell lines by inhibiting their viability and proliferation. Compounds 6 and 11 are the most potent against L. donovani, exhibiting IC50 values of 2.33 µM and 2.82 µM, respectively, better than the reference drug Miltefosine (3.66 µM). Compound 15 presented the most interesting antimalarial activity against the 3D7 strain, with IC50 = 3.21 µM. Finally, chalcone 12 gave the best result against IGR-39 melanoma cell lines, with an IC50 value of 12 µM better than the reference drug Dacarbazine (IC50 = 25 µM).
Assuntos
Chalconas , Plasmodium falciparum , Chalconas/farmacologia , Chalconas/química , Chalconas/síntese química , Humanos , Linhagem Celular Tumoral , Plasmodium falciparum/efeitos dos fármacos , Leishmania donovani/efeitos dos fármacos , Leishmania donovani/crescimento & desenvolvimento , Antimaláricos/farmacologia , Antimaláricos/síntese química , Antimaláricos/química , Antineoplásicos/farmacologia , Antineoplásicos/síntese química , Antineoplásicos/química , Proliferação de Células/efeitos dos fármacos , Sobrevivência Celular/efeitos dos fármacos , Estrutura MolecularRESUMO
The physicochemical characteristics and general food quality were greatly impacted by milling. In order to investigate the effect of milling technique for physicochemical properties of sesame paste of sesame paste, samples were prepared using ball mill and colloid mill by varying grinding times. The samples prepared by ball milling had the higher moisture contents (0.07% - 0.14%) than colloid milling (p < 0.05), except for colloid milling for one cycle (0.11%). The particle size curves showed the multimodal distributions. Compared to colloid milled samples, ball milled samples have smaller particle sizes and more uniform particle distribution. The L* values of samples prepared by ball milling were higher than colloid milling. The ball mill produced sesame paste with a wider range of hardness and silkier texture, and the samples made by ball milling for 30 min had the highest hardness. And the hardness of both CMS and BMS showed a decreasing trend with increasing grinding time. During ball milling, high-speed cutting and collision caused breakage of disulfide bonds, and the sesame proteins were decomposed to their subunits. In conclusions, ball milling may be an alternative and promising process for the preparation of sesame paste.
Assuntos
Fenômenos Químicos , Coloides , Manipulação de Alimentos , Dureza , Tamanho da Partícula , Sesamum , Sesamum/química , Manipulação de Alimentos/métodos , Coloides/química , Qualidade dos Alimentos , Fatores de Tempo , Água/química , Proteínas de Plantas/química , Proteínas de Plantas/análise , Dissulfetos/química , Dissulfetos/análiseRESUMO
Horizontal ball mills (HBMs) have been proven capable of remediating per- and polyfluoroalkyl substances (PFAS) in soil. Industrial-sized HBMs, which could easily be transported to impacted locations for on-site, ex-situ remediation, are readily available. This study examined PFAS degradation using an industrial-scale, 267 L cylinder HBM. This is the typical scale used in the industry before field application. Near-complete destruction of 6:2 fluorotelomer sulfonate (6:2 FTS), as well as the non-target PFAS in a modern fluorotelomer-based aqueous film forming foam (AFFF), was achieved when spiked onto nepheline syenite sand (NSS) and using potassium hydroxide (KOH) as a co-milling reagent. Perfluorooctanesulfonate (PFOS) showed much better and more consistent results with scale-up regardless of KOH. Perfluorooctanoate (PFOA) was examined for the first time using a HBM and behaved similarly to PFOS. Highly challenging field soils from a former firefighting training area (FFTA) were purposefully used to test the limits of the HBM. To quantify the effectiveness, free fluoride analysis was used; changes between unmilled and milled soil were measured up to 7.8 mg/kg, which is the equivalent of 12 mg/kg PFOS. Notably, this does not factor in insoluble fluoride complexes that may form in milled soils, so the actual amount of PFAS destroyed may be higher. Soil health, evaluated through the assessment of key microbial and associated plant health parameters, was not significantly affected as a result of milling, although it was characterized as poor to begin with. Leachability reached 100 % in milled soil with KOH, but already ranged from 81 to 96 % in unmilled soil. A limited assessment of the hazards associated with the inhalation of PFAS-impacted dust from ball-milling, as well as the cross-contamination potential to the environment, showed that the risk was low in both cases; however, precautions should always be taken.
RESUMO
Interest in composite thick coatings with an intermetallic matrix stimulates the development of new deposition techniques like the co-milling of pre-alloyed NiAl powder with platelet-shaped substrates. Obtained coatings were up to several micrometers thick as cold-welding of intermetallic particles was effective only at the start of this process, while later, chipping prevailed over added material. The present experiment covered the co-milling in the planetary ball mill of Ni and Al elemental powders (1:1 molar ratio) with AISI 304 steel platelets for 32 h at 300 rpm. Next, this process was repeated with an admixture of 15 wt.% of CrB2 powder. In both cases, their milling succeeded in producing up to a 200 µm coating after 4 h. The use of light, scanning and transmission electron microscopy (LM/SEM/TEM) helped to establish that the coatings had gradient microstructures with more refined crystallites of NiAl, Al3Ni2 and CrB2 closer to the surface. With the addition of a ceramic phase, the coatings presented higher hardness and lower friction during dry wear tests both at RT and at 500 °C.
RESUMO
A mechanochemical synthesis of sulfonimidamides by iron(II)-catalyzed exogenous ligand-free N-acyl nitrene transfer to sulfinamides is reported. The one-step method tolerates a wide range of sulfinamides with various substituents under solvent-free ambient conditions. Compared to its solution-phase counterpart, this mechanochemical approach shows better conversion and chemoselectivity. Mechanistic investigations by ESI-MS revealed the generation of crucial nitrene iron intermediates.
RESUMO
Mechanochemical treatment of various organic molecules is an emerging technology of green processes in biofuel, fine chemicals, or food production. Many biopolymers are involved in isolating, derivating, or modifying molecules of natural origin. Mechanochemistry provides a powerful tool to achieve these goals, but the unintentional modification of biopolymers by mechanochemical manipulation is not always obvious or even detectable. Although modeling molecular changes caused by mechanical stresses in cavitation and grinding processes is feasible in small model compounds, simulation of extrusion processes primarily relies on phenomenological approaches that allow only tool- and material-specific conclusions. The development of analytical and computational techniques allows for the inline and real-time control of parameters in various mechanochemical processes. Using artificial intelligence to analyze process parameters and product characteristics can significantly improve production optimization. We aim to review the processes and consequences of possible chemical, physicochemical, and structural changes.
Assuntos
Inteligência Artificial , Fenômenos Químicos , Biopolímeros , Estresse MecânicoRESUMO
To enhance the mechanical properties and interfacial compatibility of thermoplastic starch (TPS) highly filled poly(butylene adipate co-terephthalate) (PBAT) composite films, esterified NFC was innovatively fabricated and introduced into the composite system. The influences of NFC content and ball-milling treatment were thoroughly investigated. Interestingly, the amphiphilic esterified NFC provided a "bridge-like" effect between TPS and PBAT interfaces, which significantly improved the interfacial compatibility and mechanical properties. Notably, the tensile properties of the composite films reached their maximums at a 7 wt% NFC content, displaying a tensile strength of 6.2 MPa and an elastic modulus of 263 MPa. These values corresponded to a 59 % and 180 % increase, respectively, compared to the composition without NFC. More importantly, ball-milling contributed to uniform dispersion and surface activation of NFC, preventing starch retrogradation, and enhancing the tensile strength and elastic modulus by 30.3 % and 56.6 %, respectively. Additionally, the film exhibited excellent UV-blocking, foldable, writable, and transparent performance. These findings provide valuable data supporting the expanded applications of starch-based composite films.
Assuntos
Celulose , Amido , Módulo de Elasticidade , Resistência à Tração , PoliésteresRESUMO
Due to the reversible nature of coordination bonds and solvation effect, coordination self-assembly pathways are often difficult to elucidate experimentally in solution, as intermediates and products are in constant equilibration. The present study shows that some of these transient and high-energy self-assembly intermediates can be accessed by means of ball-milling approaches. Among them, highly aqueous-unstable Pd3 L11 and Pd6 L14 open-cage intermediates of the framed Fujita Pd6 L14 cage and Pd2 L22 , Pd3 L21 and Pd4 L22 intermediates of Mukherjee Pd6 L24 capsule are successfully trapped in solid-state, where Pd=tmedaPd2+ , L1=2,4,6-tris(4-pyridyl)-1,3,5-triazine and L2=1,3,5-tris(1-imidazolyl)benzene). Their structures are assigned by a combination of solution-based characterization tools such as standard NMR spectroscopy, DOSYâ NMR, ESI-MS and X-ray diffraction. Collectively, these results highlight the opportunity of using mechanochemistry to access unique chemical space with vastly different reactivity compared to conventional solution-based supramolecular self-assembly reactions.
RESUMO
Cement production contributes significantly to carbon dioxide emissions. Alkali-activated materials offer an environmentally friendly alternative due to their comparable strength, durability and low-carbon emissions while utilizing wastes and industrial by-products. Wood ash is a waste material that shows promising results as a partial replacement for Portland cement and precursors in alkali-activated systems. The aim of this study was to examine the effect of ground wood ash on the mechanical properties of alkali-activated mortars. Wood ash was incorporated as a 0 wt%, 10 wt% and 20 wt% partial replacement for ground granulated blast furnace slag (GGBFS). The wood ashes were ground in a planetary ball mill for 10 and 20 min. Sodium silicate (Na2SiO3), sodium carbonate (Na2CO3), and sodium hydroxide (NaOH) were used as alkali activators. The results demonstrated that ground wood ash improved the mechanical properties of alkali-activated systems compared to untreated wood ash. However, the incorporation of wood ash increased the porosity of the binder matrix.
RESUMO
The combination of a nickel(II) catalyst and a mechanoredox catalyst under ball-milling conditions promotes mechanical-force-driven C-N cross-coupling reactions. In this nickel(II)/mechanoredox cocatalyst system, the modulation of the oxidation state of the nickel center, induced by piezoelectricity, is used to facilitate a highly efficient aryl-amination reaction, which is characterized by a broad substrate scope, an inexpensive combination of catalysts (NiBr2 and BaTiO3 ), short reaction times, and an almost negligible quantity of solvents. Moreover, this reaction can be readily up-scaled to the multi-gram scale, and all synthetic operations can be carried out under atmospheric conditions without the need for complicated reaction setups. Furthermore, this force-induced system is suitable for excitation-energy-accepting molecules and poorly soluble polyaromatic substrates that are incompatible with solution-based nickel(II)/photoredox cocatalysts.
RESUMO
The conventional dosage form of Ethyol® (amifostine), a sterile lyophilized powder, involves reconstituting it with 9.7 mL of sterile 0.9% sodium chloride in accordance with the United States Pharmacopeia specifications for intravenous infusion. The purpose of this study was to develop inhalable microparticles of amifostine (AMF) and compare the physicochemical properties and inhalation efficiency of AMF microparticles prepared by different methods (jet milling and wet ball milling) and different solvents (methanol, ethanol, chloroform, and toluene). Inhalable microparticles of AMF dry powder were prepared using a wet ball-milling process with polar and non-polar solvents to improve their efficacy when delivered through the pulmonary route. The wet ball-milling process was performed as follows: AMF (10 g), zirconia balls (50 g), and solvent (20 mL) were mixed and placed in a cylindrical stainless-steel jar. Wet ball milling was performed at 400 rpm for 15 min. The physicochemical properties and aerodynamic characteristics of the prepared samples were evaluated. The physicochemical properties of wet-ball-milled microparticles (WBM-M and WBM-E) using polar solvents were confirmed. Aerodynamic characterization was not used to measure the % fine particle fraction (% FPF) value in the raw AMF. The % FPF value of JM was 26.9 ± 5.8%. The % FPF values of the wet-ball-milled microparticles WBM-M and WBM-E prepared using polar solvents were 34.5 ± 0.2% and 27.9 ± 0.7%, respectively; while the % FPF values of the wet-ball-milled microparticles WBM-C and WBM-T prepared using non-polar solvents were 45.5 ± 0.6% and 44.7 ± 0.3%, respectively. Using a non-polar solvent in the wet ball-milling process resulted in a more homogeneous and stable crystal form of the fine AMF powder than using a polar solvent.
RESUMO
Background: One of the imperative progressions within the pharmaceutical industry, especially drugs, is the expanded utilization of materials in order to enhance its dissolution, solubility and bioavailability. Planetary ball monomill approach can be the latest entrant to Green nanotechnology - being solvent-free, eco-friendly, cost-effective, and sustainable particle size reduction approach. Objectives: Salicylic acid nanopowder (SA-NP) was aimed to be prepared using planetary ball monomill by dry milling technique to enhance its solubility and bioavailability. Methods: Various milling parameters such as milling speed, milling time and number of balls was varied and their effect on dependent responses including size (nm) and polydispersity indices (PDI) were evaluated using a 3-Factorial-3-Level Box-Behnken statistical design. Particle size and PDI analysis was performed using light scattering technique. Results: The particle size of salicylic acid obtained by optimizing the dry milling parameters was Z-Average (d.nm): 776.3 nm and PDI: 0.600 up to Z-Average (d. nm): 205.0 nm and PDI: 0.383. Conclusions: Dry milling can be used for the preparation of nanopowders of drug candidates with poor water-solubility issues. Present day medications have nano-scaled active ingredients which are rapidly absorbed by the human body as compared to the conventional ones. Enlarged surface area increases the solubility of the drug, thereby improves its bioavailability.
RESUMO
Ball milling is used for comminution by rotating a drum to grind materials using balls with specific diameters. Ball milling advantages include the potential for high capacity, predicted fineness in a specific amount of time, reliability, safety, and simplicity, but has disadvantages of high weight, energy consumption and costs, which limit accessibility. To overcome these limitations this study applies the free and open source hardware approach coupled to distributed digital manufacturing to fabricate a ball mill with a simple, customizable design that can be used in a wide range of scientific applications and circumstances including those without access to reliable grid electricity. The highly-customizable design reduces the cost to
RESUMO
Attached, old mortar removal methods are evolving to improve recycled aggregate quality. Despite the improved quality of recycled aggregate, treatment of recycled aggregate at the required level cannot be obtained and predicted well. In the present study, an analytical approach was developed and proposed to use the Ball Mill Method smartly. As a result, more interesting and unique results were found. One of the interesting results was the abrasion coefficient which was composed according to experimental test results; and the Abrasion Coefficient enables quick decision-making to get the best results for recycled aggregate before the Ball mill method application on recycled aggregate. The proposed approach provided an adjustment in water absorption of recycled aggregate, and the required reduction level in water absorption of recycled aggregate was easily achieved by accurately composing Ball Mill Method combinations (drum rotation-steel ball). In addition, artificial neural network models were built for the Ball Mill Method The artificial neural network input parameters were Ball Mill Method drum rotations, steel ball numbers and/or Abrasion Coefficient, and the output parameter was the water absorption of recycled aggregate. Training and testing processes were conducted using the Ball Mill Method results, and the results were compared with test data. Eventually, the developed approach gave the Ball Mill Method more ability and more effectiveness. Also, the predicted results of the proposed Abrasion Coefficient were found close to the experimental and literature data. Besides, an artificial neural network was found to be a useful tool for the prediction of water absorption of processed recycled aggregate.
RESUMO
A protocol for the mechanochemical synthesis of copper(I)/N-heterocyclic carbene complexes using cheap and readily available K3PO4 as base has been developed. This method employing a ball mill is amenable to typical simple copper(I)/NHC complexes but also to a sophisticated copper(I)/N-heterocyclic carbene complex bearing a guanidine moiety. In this way, the present approach circumvents commonly employed silver(I) complexes which are associated with significant and undesired waste formation and the excessive use of solvents. The resulting bifunctional catalyst has been shown to be active in a variety of reduction/hydrogenation transformations employing dihydrogen as terminal reducing agent.