Boosting stable lithium deposition via Li3N-Enriched inorganic SEI induced by a polycationic polymer layer.

Lithium (Li) metal is a promising anode material for future high-energy rechargeable batteries due to its remarkable properties. Nevertheless, excess Li in traditional lithium metal anodes (LMAs) reduces the energy density of batteries and increases safety risks. Electrochemical pre-lithiation is an effective technique for regulating the lithium content of the anodes. However, Cu foil or other non-Li based substrates used for pre-lithiation often have inhomogeneous surfaces and high nucleation barrier, leading to uneven tip deposition of lithium metal and fragile SEI. Herein, we have designed an interfacial layer composed of nano-Si particles and cationic polymer (poly (diallyldimethylammonium chloride)) (denoted as Si@PDDA) to induce the formation of Li3N-rich inorganic SEI and regulate the homogeneous plating/stripping of lithium. The uniformly dispersed nano-Si particles can decrease the Li+ nucleation overpotential through alloying reaction with lithium. The surface of Si nano-particles modified by PDDA contains numerous cationic sites, providing an electrostatic shielding layer to seeding the growth of Li metal and inhibiting dendrites formation. More promisingly, PDDA adsorbs electrolyte anions while transporting Li+, significantly accelerating the decomposition kinetics of inorganic salts within the electrolyte. Therefore, a SEI film rich in Li3N was formed on the anodes, ensuring the excellent interfacial stability and electrochemical cycling performance of LMAs. The symmetrical cells exhibit a cycle life of 900 h at 1 mA cm-2. Moreover, the practical full cells operate at a low negative/positive (N/P) capacity ratio (∼3) for over 160 cycles.

Cationic polymer-mediated interbacterial aggregation: A novel approach for rapid aerobic granules development.

This study introduces a novel approach to aerobic granular sludge technology that minimizes the start-up time and guarantees the formation of stable granules. This is achieved by seeding the reactor with a cationic polymer without using inoculated sludge. Three cationic polymers (Hydrofloc C4400SA, C8896, and polyelectrolyte emulsion) were tested to determine the most appropriate polymer for aerobic granular sludge (AGS) startup based on the optimal dose and formation of aerobic granules. Hydrofloc cationic polymer C4400SA has excellent granule-forming properties in the AGS reactor compared to their counterparts. The formation of granules was boosted by adding 15 ppm of polymer, resulting in densely packed aerobic granules after 10 days. This improvement can be due to the more cationic properties of hydrofloc, which play a key role in bridging between cells and particles because the cationic charges of hydrofloc attract negatively charged bacteria in wastewater, thereby promoting aggregation and the formation of initial flocs. These flocs serve as the foundation for the development of granules. After 80 days of operation, 40-50% of particles with an average size range from 0.6 to 0.9 mm were observed. The AGS SBR operation was closely monitored and showed consistent efficiency in removing solids, where TP, TN, NH+4 -N, and the total soluble COD were removed at average efficiencies of 62%, 73%, 97%, 93%, and 79% respectively, during steady-state cycles conducted at room temperature. Overall, this study highlights the potential of hydrofloc cationic polymer C4400SA to enhance the performance and resilience of AGS in wastewater treatment applications.

Strip biosensors based on broad-spectrum aptamers and cationic polymers for the on-site rapid detection of tetracycline antibiotics residues in milk.

A lateral flow chromatography strip (LFS) is a chromatography-based biosensor with advantages of convenient portability, simple operation and rapid detection. In this study, a novel rapid detection technique of aptamer-based chromatography strip was developed and used for the first time for the residue detection of tetracycline antibiotics (TCs) in various milk samples. In this method, gold nanoparticles (AuNPs) modified by TCs specific aptamers were used as probes, and cationic polymers as capture molecules in a test line (T-line). Meanwhile, the analysis of the gray value of the T-line enabled a linear detection range of 1-300 nM and a limit of detection (LOD) of 0.33 nM for quantitative analysis. The biosensor demonstrated high specificity, good stability, and successfully detected tetracyclines in milk samples with recovery rate of 93.60%-106.20%. This method sets a basis for multi-residue antibiotics detection in diverse samples, showing potential for on-site applications.

Effect of multifunctional cationic polymer coatings on mitigation of broad microbial pathogens.

Infection control measures to prevent viral and bacterial infection spread are critical to maintaining a healthy environment. Pathogens such as viruses and pyogenic bacteria can cause infectious complications. Viruses such as SARS-CoV-2 are known to spread through the aerosol route and on fomite surfaces, lasting for a prolonged time in the environment. Developing technologies to mitigate the spread of pathogens through airborne routes and on surfaces is critical, especially for patients at high risk for infectious complications. Multifunctional coatings with a broad capacity to bind pathogens that result in inactivation can disrupt infectious spread through aerosol and inanimate surface spread. This study uses C-POLAR, a proprietary cationic, polyamine, organic polymer with a charged, dielectric property coated onto air filtration material and textiles. Using both SARS-CoV-2 live viral particles and bovine coronavirus models, C-POLAR-treated material shows a dramatic 2-log reduction in circulating viral inoculum. This reduction is consistent in a static room model, indicating simple airflow through a static C-POLAR hanging can capture significant airborne particles. Finally, Gram-positive and Gram-negative bacteria are applied to C-POLAR textiles using a viability indicator to demonstrate eradication on fomite surfaces. These data suggest that a cationic polymer surface can capture and eradicate human pathogens, potentially interrupting the infectious spread for a more resilient environment. IMPORTANCE: Infection control is critical for maintaining a healthy home, work, and hospital environment. We test a cationic polymer capable of capturing and eradicating viral and bacterial pathogens by applying the polymer to the air filtration material and textiles. The data suggest that the simple addition of cationic material can result in the improvement of an infectious resilient environment against viral and bacterial pathogens.

Immune checkpoint reprogramming via sequential nucleic acid delivery strategy optimizes systemic immune responses for gastrointestinal cancer immunotherapy.

Monoclonal antibodies targeting immune checkpoints have been widely applied in gastrointestinal cancer immunotherapy. However, systemic administration of various monoclonal antibodies does not often result in sustained effects in reversing the immunosuppressive tumor microenvironment (TME), which may be due to the spatiotemporal dynamic changes of immune checkpoints. Herein, we reported a novel immune checkpoint reprogramming strategy for gastrointestinal cancer immunotherapy. It was achieved by the sequential delivery of siPD-L1 (siRNA for programmed cell death ligand 1) and pOX40L (plasmid for OX40 ligand), which were complexed with two cationic polymer brush-grafted carbon nanotubes (dense short (DS) and dense long (DL)) designed based on the structural characteristics of nucleic acids and brush architectures. Upon administrating DL/pOX40L for the first three dosages, then followed by DS/siPD-L1 for the next three dosages to the TME, it upregulated the stimulatory checkpoint OX40L on dendritic cells (DCs) and downregulated inhibitory checkpoint PD-L1 on tumor cells and DCs in a sequential reprogramming manner. Compared with other combination treatments, this sequential strategy drastically boosted the DCs maturation, and CD8+ cytotoxic T lymphocytes infiltration in tumor site. Furthermore, it could augment the local antitumor response and improve the T cell infiltration in tumor-draining lymph nodes to reverse the peripheral immunosuppression. Our study demonstrated that sequential nucleic acid delivery strategy via personalized nanoplatforms effectively reversed the immunosuppression status in both tumor microenvironment and peripheral immune landscape, which significantly enhanced the systemic antitumor immune responses and established an optimal immunotherapy strategy against gastrointestinal cancer.

Efficient removal of perrhenate/pertechnetate by a pyridinium-based porous polymer.

The extraction of 99TcO4- from radioactive effluents is extremely crucial for the purposes of nuclear disposal and environmental remediation. Herein, utilizing a facile and low-cost synthesis method, we report a pyridinium-based cationic polymer network, CPP-Cl, with impressive adsorption performance and ultrafast adsorption kinetics towards ReO4-. The structure featuring highly density of charged pyridinium units was synthesized, making it an effective adsorbent for capturing ReO4-. The material showed fast ReO4- adsorption kinetics reaching adsorption equilibrium within 30 s, an excellent capture capability of 1069.7 mg/g, and exceptional separation efficiency of 94.3% for removing 1000 ppm ReO4-. Furthermore, it possessed excellent reusability in multiple sorption/desorption trials and good uptake capacity within a widely ranging pH values. It is noteworthy that the extraction efficiency of CPP-Cl for ReO4- from simulated nuclear waste can be up to 94.2%. The favorable performance of the material in multiple tests revealed that CPP-Cl has tremendous potential as a high-efficiency sorbent for capturing 99TcO4-/ReO4- in complex nuclear associated environmental systems.

Magnetic quaternary ammonium polymer bearing porous agarose for selective extraction of Aristolochic acids in the plasma.

Aristolochic acids (AAs) naturally occurring in the herbal genus Aristolochia are associated with a high risk of kidney failure, multiple tumors and cancers. However, approaches with high selectivity and rapidity for measuring AAs in biological samples are still inadequate. Inspired by the mechanism of AAs-induced nephrotoxicity, we designed a hybrid magnetic polymer-porous agarose (denoted as MNs@SiO2M@DNV-A), mimicking the effect of basic and aromatic residues of organic anion transporter 1 (OAT1) for efficient enriching aristolochic acid I (AA I) and aristolochic acid II (AA II) in the plasma. The monomers of vinylbenzyl trimethylammonium chloride (VBTAC), N-vinyl-2-pyrrolidinone (NVP) and divinylbenzene (DVB) were employed to construct the polymer layer, which provided a selective adsorption for AAs by multiple interactions. The porous agarose shell contributed to remove interfering proteins in the plasma samples. A magnetic solid-phase extraction (MSPE) based on the proposed composite enhanced the selectivity toward AA I and AA II in the plasma samples. In combination of HPLC analysis, the proposed method was proved to be applicable to fast and specific quantification of AAs in blood samples, which was characterized by a good linearity, high sensitivity, acceptable recovery, excellent repeatability and satisfactory reusability.

Phytic Acid-Promoted Deposition of Gold Nanoparticles with Grafted Cationic Polymer Brushes for the Construction of Synergistic Contact-Killing and Photothermal Bactericidal Coatings.

Medical implants are constantly facing the risk of bacterial infections, especially infections caused by multidrug resistant bacteria. To mitigate this problem, gold nanoparticles with alkyl bromide moieties (Au NPs-Br) on the surfaces were prepared. Xenon light irradiation triggered the plasmon effect of Au NPs-Br to induce free radical graft polymerization of 2-(dimethylamino)ethyl methacrylate (DMAEMA), leading to the formation of poly(DMAEMA) brush-grafted Au NPs (Au NPs-g-PDM). The Au NPs-g-PDM nanocomposites were conjugated with phytic acid (PA) via electrostatic interaction and van der Waals interaction. The as-formed aggregates were deposited on the titanium (Ti) substrates to form the PA/Au NPs-g-PDM (PAP) hybrid coatings through surface adherence of PA and the gravitational effect. Synergistic bactericidal effects of contact-killing caused by the cationic PDM brushes, and local heating generated by the Au NPs under near-infrared irradiation, conferred strong antibacterial effects on the PAP-deposited Ti (Ti-PAP) substrates. The synergistic bactericidal effects reduced the threshold temperature required for the photothermal sterilization, which in turn minimized the secondary damage to the implant site. The Ti-PAP substrates exhibited 97.34% and 99.97% antibacterial and antiadhesive efficacy, respectively, against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli), compared to the control under in vitro antimicrobial assays. Furthermore, the as-constructed Ti-PAP surface exhibited a 99.42% reduction in the inoculated S. aureus under in vivo assays. In addition, the PAP coatings exhibited good biocompatibility in the hemolysis and cytotoxicity assays as well as in the subcutaneous implantation of rats.

Record High Iodate Anion Capture by a Redox-Active Cationic Polymer Network.

As a critical radioactive anionic contaminant, traditional adsorbents primarily remove iodate (IO3 -) through ion exchange or hard acid-hard base interactions, but suffer from limited affinity and capacity. Herein, employing the synergistic effect of ion exchange and redox, we successfully synthesized a redox-active cationic polymer network (SCU-CPN-6, [C9H10O2N5 ⋅ Cl]n) by merging guanidino groups with ion-exchange capability and phenolic groups with redox ability via a Schiff base reaction. SCU-CPN-6 exhibits a groundbreaking adsorption capacity of 896 mg/g for IO3 -. The inferior adsorption capacities of polymeric networks containing only redox (~0 mg/g) or ion exchange (232 mg/g) fragments underscore the synergistic "1+1>2" effect of the two mechanisms. Besides, SCU-CPN-6 shows excellent uptake selectivity for IO3 - in the presence of high concentrations of SO4 2-, Cl-, and NO3 -. Meanwhile, a high distribution coefficient indicates its exemplary deep-removal performance for low IO3 - concentration. The synergic strategy not only presents a breakthrough solution for the efficient removal of IO3 - but also establishes a promising avenue for the design of advanced adsorbents for diverse applications.

Natural Polymer-Based Nanogel for pH-Responsive Delivery of Sorafenib Tosylate in Hemangiosarcoma.

Smart nanomedicinal treatment for cancer manifests a solubility challenge with inherent nanoscale size and nonspecific release with stimuli-responsive potential. This is the limelight in novel chemotherapy to pursue physiochemical differences between the tumor microenvironment (TME) and normal cells, which introduces active groups of nanocarriers responding to various stimuli, endowing them with concise responses to various tumor-related signals. The nanogels were successfully prepared by a modified solvent evaporation technique. Nine batches were formulated by changing the chitosan concentration (12, 14, 16 mg/ml) and sonication time (5, 10, 15 min). The formulations were optimized for particle size and zeta potential with high percent entrapment efficiency (%EE) through Central Composite Design software. The optimized batch F7 had a 182-nm size and high zeta potential (64.5 mV) with 98% EE. The drug release of F7 was higher at pH 6 (97.556%) than at pH 7.4 (45.113%). The pharmacokinetic study shows that the release follows the Hixon plot model (R2 = 0.9334) that shifts to zero order (R2 = 0.9149). The nanogel F7 was observed for stability and showed an absence of color change, phase separation, and opacity for 6 months. In the present study, the pH difference between cancer cells and normal cells is the key point of the smart nanogel. This study is promising but challenging depending on the in vivo study. The nanogel was successfully prepared and evaluated for pH-responsive release. As hemangiosarcoma commonly occurs in dogs, this formulation helps to limit the difficulties with administration.

Antibacterial Zirconia Surfaces from Organocatalyzed Atom-Transfer Radical Polymerization.

Antibacterial coatings are becoming increasingly attractive for application in the field of biomaterials. In this framework, we developed polymer coating zirconia with antibacterial activity using the "grafting from" methodology. First, 1-(4-vinylbenzyl)-3-butylimidazolium chloride monomer was synthesized. Then, the surface modification of zirconia substrates was performed with this monomer via surface-initiated photo atom transfer radical polymerization for antibacterial activity. X-ray photoelectron spectroscopy, ellipsometry, static contact angle measurements, and an atomic force microscope were used to characterize the films for each step of the surface modification. The results revealed that cationic polymers could be successfully deposited on the zirconia surfaces, and the thickness of the grafted layer steadily increased with polymerization time. Finally, the antibacterial adhesion test was used to evaluate the antibacterial activity of the modified zirconia substrates, and we successfully showed the antibacterial activity against Staphylococcus aureus and Pseudomonas aeruginosa strains.

Enhancing antifungal and biocompatible efficacy of undecanoic acid through incorporation with chitosan-based nanoemulsion.

The management of invasive fungal infections in humans poses significant challenges due to the intricate nature of the treatment, which is both arduous and costly, necessitating routine diagnostic procedures. Consequently, this investigation aimed to formulate a chitosan-based nanoemulsion (CS NEMs) incorporating the antifungal agent undecanoic acid (UDA), characterizing these NEMs and assessing their antifungal efficacy against both filamentous and non-filamentous fungal pathogens. The CS-based UDA NEMs were synthesized by introducing the surfactant Triton X-100 and the stabilizer glycerol. Nanoparticle tracking analysis (NTA) and SEM demonstrated the CS-UDA NEMs with an average size of 145 nm and 164.5 ± 24 nm, respectively. The successful formation of CS-UDA NEMs was verified through FTIR and XRD. CS-UDA NEMs exhibited exceptional inhibition against Aspergillus flavus, Aspergillus fumigatus, Aspergillus niger, and Candida albicans with MFC of 500, 500, 250 and 250 µg/mL, respectively. Additionally, CS-UDA NEMs displayed comparatively lower antioxidant activity as determined by DPPH and ABTS radical scavenging assays. Importantly, CS-UDA NEMs demonstrated no cytotoxic effects on NIH3T3 cells even at higher concentration (1000 µg/mL), as confirmed by cell viability and fluorescent staining assays. In conclusion, this study suggests that the developed CS-UDA NEMs hold promise as potent antifungal agents with diverse potential applications.

Time-Resolved Killing of Individual Bacterial Cells by a Polycationic Antimicrobial Polymer.

Polycationic polymers are widely studied antiseptics, and their efficacy is usually quantified by the solution concentration required to kill a fraction of a population of cells (e.g., by Minimum Bactericidal Concentration (MBC)). Here we describe how the response to a polycationic antimicrobial varies greatly among members of even a monoclonal population of bacteria bathed in a single common antimicrobial concentration. We use fluorescence microscopy to measure the adsorption of a labeled cationic polymer, polydiallyldimethylammmonium chloride (PDADMAC, Mw ≈ 4 × 105 g mol-1) and the time course of cell response via a cell permeability indicator for each member of an ensemble of either Escherichia coli, Staphylococcus aureus, or Pseudomonas aeruginosa cells. This is a departure from traditional methods of evaluating synthetic antimicrobials, which typically measure the overall response of a collection of cells at a particular time and therefore do not assess the diversity within a population. Cells typically die after they reach a threshold adsorption of PDADMAC, but not always. There is a substantial time lag of about 5-10 min between adsorption and death, and the time to die of an individual cell is well correlated with the rate of adsorption. The amount adsorbed and the time-to-die differ among species but follow a trend of more adsorption on more negatively charged species, as expected for a cationic polymer. The study of individual cells via time-lapse microscopy reveals additional details that are lost when measuring ensemble properties at a particular time.

PEI-based functional materials: Fabrication techniques, properties, and biomedical applications.

Cationic polymers have recently attracted considerable interest as research breakthroughs for various industrial and biomedical applications. They are particularly interesting due to their highly positive charges, acceptable physicochemical properties, and ability to undergo further modifications, making them attractive candidates for biomedical applications. Polyethyleneimines (PEIs), as the most extensively utilized polymers, are one of the valuable and prominent classes of polycations. Owing to their flexible polymeric chains, broad molecular weight (MW) distribution, and repetitive structural units, their customization for functional composites is more feasible. The specific beneficial attributes of PEIs could be introduced by purposeful functionalization or modification, long service life, biocompatibility, and distinct geometry. Therefore, PEIs have significant potential in biotechnology, medicine, and bioscience. In this review, we present the advances in PEI-based nanomaterials, their transfection efficiency, and their toxicity over the past few years. Furthermore, the potential and suitability of PEIs for various applications are highlighted and discussed in detail. This review aims to inspire readers to investigate innovative approaches for the design and development of next-generation PEI-based nanomaterials possessing cutting-edge functionalities and appealing characteristics.

Reduction of Pro-Inflammatory Markers in RAW264.7 Macrophages by Polyethylenimines.

The physiological problem of chronic inflammation and its associated pathologies attract ongoing attention with regard to methods for their control. Current systemic pharmacological treatments present problematic side effects. Thus, the possibility of new anti-inflammatory compounds with differing mechanisms of action or biophysical properties is enticing. Cationic polymers, with their ability to act as carriers for other molecules or to form bio-compatible materials, present one such possibility. Although not well described, several polycations such as chitosan and polyarginine, have displayed anti-inflammatory properties. The present work shows the ubiquitous laboratory transfection reagent, polyethylenimine (PEI) and more specifically low molecular weight branched PEI (B-PEI) as also possessing such properties. Using a RAW264.7 murine cell line macrophage as an inflammation model, it is found the B-PEI 700 Da as being capable of reducing the production of several pro-inflammatory molecules induced by the endotoxin lipopolysaccharide. Although further studies are required for elucidation of its mechanisms, the revelation that such a common lab reagent may present these effects has wide-ranging implications, as well as an abundance of possibilities.

Use of wastewater alum-coagulation sludge as a phosphorus fertiliser - a mini review.

The use of aluminium (Al) salts, particularly alum, in coagulation is a widespread and conventional treatment method for eliminating pollutants, including phosphorus (P) which can cause eutrophication, from wastewater. However, a significant challenge of this process is the substantial amount of sludge generated, necessitating proper disposal. Historically, land disposal has been a common practice, but it poses potential issues for plant life on these lands. Despite the associated drawbacks, sludge contains elevated concentrations of vital plant nutrients like P and nitrogen, presenting an opportunity for beneficial use in agriculture. Given the imminent scarcity of P fertilizers due to the eventual depletion of high-grade P ores, this review explores the potential advantages and challenges of utilizing Al sludge as a P source for plants and proposes measures for its beneficial application. One primary concern with land application of Al sludge is its high levels of soluble Al, known to be toxic to plants, particularly in acidic soils. Another issue arises from the elevated Al concentration is P fixation and subsequently reducing P uptake by plants. To address these issues, soil treatment options such as lime, gypsum, and organic matter can be employed. Additionally, modifying the coagulation process by substituting part of the Al salts with cationic organic polymers proves effective in reducing the Al content of the sludge. The gradual release of P from sludge into the soil over time proves beneficial for plants with extended growth periods.

Synthesizing cationic polymers and tuning their properties for microalgae harvesting.

This study reports a facile technique to synthesize and tune the cationic polymer, poly(3-acrylamidopropyl)trimethylammonium chloride (PAPTAC), in terms of molecular weight and surface change for harvesting three microalgae species (Scenedesmus sp., P.purpureum, and C. vulgaris). The PAPTAC polymer was synthesised by UV-induced free-radical polymerisation. Polymer tuning was demonstrated by regulating the monomer concentration (60 to 360 mg/mL) and UV power (36 and 60 W) for polymerisation. The obtained PAPTAC polymer was evaluated for harvesting three different microalgae species and compared to a commercially available polymer. The highest flocculation efficiency for Scenedesmus sp. and P. purpureum was observed at a dosage of 25 mg-polymer/g of dry biomass by using PAPTAC-90, resulting in higher flocculation efficiency than the commercial polymer. Results in this study show evidence of effective neutralisation of the negative charge surface of microalgae cells by the produced cationic PAPTAC polymer and polymer bridging for effective flocculation. The obtained PAPTAC polymer was less effective for harvesting C. vulgaris, possibly due to other factors such as cell morphology and composition of extracellular polymeric substances of at the cell membrane that may also influence harvesting performance.

Low-Hysteresis and High-Toughness Hydrogels Regulated by Porous Cationic Polymers: the Effect of Counteranions.

Service life and range of polymer materials is heavily reliant on their elasticity and mechanical stability under long-term loading. Slippage of chain segments under load leads to significant hysteresis of the hydrogels, limiting its repeatability and mechanical stability. Achieving the desired elasticity exceeding that of rubber is a great challenge for hydrogels, particularly when subjected to large deformations. Here, low-hysteresis and high-toughness hydrogels were developed through controllable interactions of porous cationic polymers (PCPs) with adjustable counteranions, including reversible bonding of PCP frameworks/polymer segments (polyacrylamide, PAAm) and counteranions/PAAm. This strategy reduces chain segment slippage under load, endowing the PCP-based hydrogels (PCP-gels) with good elasticity under large deformations (7 % hysteresis at a strain ratio of 40). Furthermore, due to the enlarged chain segments entanglement by PCP, the PCP-gels exhibit large strain (13000 %), significantly enhanced toughness (68 MJ m-3 ), high fracture energy (43.1 kJ m-2 ), and fatigue resistance. The unique properties of these elastic PCP-gels have promising applications in the field of flexible sensors.

Antibacterial Synthetic Nanocelluloses Synergizing with a Metal-Chelating Agent.

Antibacterial materials composed of biodegradable and biocompatible constituents that are produced via eco-friendly synthetic strategies will become an attractive alternative to antibiotics to combat antibiotic-resistant bacteria. In this study, we demonstrated the antibacterial properties of nanosheet-shaped crystalline assemblies of enzymatically synthesized aminated cellulose oligomers (namely, surface-aminated synthetic nanocelluloses) and their synergy with a metal-chelating antibacterial agent, ethylenediaminetetraacetic acid (EDTA). Growth curves and colony counting assays revealed that the surface-aminated cellulose assemblies had an antibacterial effect against Gram-negative Escherichia coli (E. coli). The cationic assemblies appeared to destabilize the cell wall of E. coli through electrostatic interactions with anionic lipopolysaccharide (LPS) molecules on the outer membrane. The antibacterial properties were significantly enhanced by the concurrent use of EDTA, which potentially removed metal ions from LPS molecules, resulting in synergistic bactericidal effects. No antibacterial activity of the surface-aminated cellulose assemblies was observed against Gram-positive Staphylococcus aureus even in the presence of EDTA, further supporting the contribution of electrostatic interactions between the cationic assemblies and anionic LPS to the activity against Gram-negative bacteria. Analysis using quartz crystal microbalance with dissipation monitoring revealed the attractive interaction of the surface-aminated cellulose assembly with LPS Ra monolayers artificially produced on the device substrate.

Intranasal mRNA Delivery via Customized RNA-Polyplex Nanoparticles Enhancing Gene Expression through Photochemical Mechanisms.

Achieving effective mRNA expression in vivo requires careful selection of an appropriate delivery vehicle and route of administration. Among the various routes of administration, intranasal administration has received considerable attention due to its ability to induce potent immune responses. In this context, we designed a specialized cationic polymer tailored for delivery of mRNA into the nasal cavity. These polymers are designed with varying degrees of substitution in different amine groups to allow for identification of the most suitable amine moiety for effective mRNA delivery. We also incorporated a photosensitizer within the polymer structure that can trigger the generation of reactive oxygen species when exposed to light. The synthesized cationic polymer is complexed with anionic mRNA to form a polyplex. Illuminating these polyplexes with laser light enhances their escape from intracellular endosomes, stimulating mRNA translocation into the cytoplasm, followed by increased mRNA expression at the cellular level. Through intranasal administration to C57BL/6 mice, it was confirmed that these photoactive polyplexes effectively induce mRNA expression and activate immune responses in vivo using photochemical effects. This innovative design of a photoactivated cationic polymer presents a promising and reliable strategy to achieve efficient intranasal mRNA delivery. This approach has potential applications in the development of mRNA-based vaccines for both prophylactic and therapeutic purposes.