RESUMO
INTRODUCTION: The efficiency of zinc oxide (ZnO) nanoparticles for environmental decontamination is limited by their reliance on ultraviolet (UV) light and rapid charge carrier recombination. Carbon doping has been proposed to address these challenges by potentially enhancing visible light absorption and charge separation. OBJECTIVES: This study aims to introduce a novel, single-step synthesis method for carbon-doped ZnO (C-Z) nanoparticles, leveraging the decomposition of zinc nitrate hexahydrate and furfural under a nitrogen atmosphere to improve photocatalytic activity under visible light. METHODS: A series of C-Z variants (C-Z-1 to C-Z-5) and an undoped sample (ZnO-0) were synthesized. The influence of furfural on the synthesis process and doping mechanism was analyzed by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and UV-visible diffuse reflectance spectroscopy (DRS). RESULTS: XPS confirmed the integration of carbon within the ZnO matrix, and XRD indicated increased lattice dimensions owing to doping. DRS revealed bandgap narrowing, suggesting enhanced charge separation. Among the variants, C-Z-3 significantly outperformed the others, showing a 12-fold increase in the photocatalytic degradation rate of Rhodamine B compared to undoped ZnO. CONCLUSION: The developed single-step synthesis method for C-Z nanoparticles represents a major advancement in materials engineering for ecological applications. The enhanced photocatalytic activity under visible light, as demonstrated by C-Z-3, underscores the potential of these nanoparticles for environmental decontamination.
RESUMO
Contact Electro-Catalysis (CEC) using commercial dielectric materials in contact-separation cycles with water triggers interfacial electron transfer, generating reactive oxygen species (ROS). However, the hydrophobicity of these materials limits reaction sites, and the generated ROS often combine to form hydrogen peroxide (H2O2), which does not decompose further, leading to suboptimal rates. Addressing H2O2 generation and activation is crucial for advancing CEC. Here, we synthesized a catalyst by loading polytetrafluoroethylene (PTFE) onto ZSM-5 (PZ), achieving uniform dispersion in water. Introducing an FeIII-initiated self-cycling Fenton system (SF-CEC), with synergistic O2 activation and FeIII-activated H2O2, enhanced ROS generation. This system enabled nearly 99% degradation of azo dyes within 10 minutes, a sixfold improvement over traditional CEC. It represents the fastest ultrasound-induced degradation rate of methyl orange dye to date. Without extra oxidants, it also achieved stable dissolution of precious metals in weakly acidic solutions at room temperature, with 80% gold dissolution within 2 hours-2.5 times faster than similar systems. This study corrects the perception of CEC under acidic conditions, offering new insights for dye degradation and precious metal recovery.
RESUMO
In awareness of industrial dye wastewater, carbon quantum dots (CQDs) and cobalt zinc ferrite (CZF) nanocomposites were synthesised for the making of carbon quantum dots coated cobalt zinc ferrite (CZF@CQDs) nanophotocatalyst using oxidative polymerization reaction. The results of TEM, zeta potential value, and FTIR confirm highly dispersed 1-4 nm particles with the - 45.7 mV carboxylic functionalized surface of CQDs. The results of the synthesised CZF@CQDs photocatalyst showed an average particle size of ~ 15 nm according to TEM, SEM, and XRD. The photocatalyst showed a 1.20 eV band gap, which followed the perfect visible light irradiation. TGA and DTA revealed the good thermal stability of the nanophotocatalyst. VSM was carried out, and the saturation magnetisations for CZF and CZF@CQDs were 42.44 and 36.14 emu/g, respectively. A multipoint study determined the BET-specific surface area of the CZF@CQDs photocatalyst to be 149.87 m2/g. Under visible light irradiation, the final CZF@CQDs nanophotocatalyst demonstrated remarkable efficiency (~ 95% within 25 min) in the photocatalytic destruction of Reactive Blue 222 (RB 222) and Reactive Yellow 145 (RY 145) dyes, as well as mechanical stability and recyclability. Even after the recycling of the degradation study, the nanophotocatalyst efficiency (~ 82%, 7th cycles) was predominantly maintained. The effects of several parameters were also investigated, including initial dye concentration, nanophotocatalyst concentration, CQD content, initial pH of the dye solution, and reaction kinetics. Degradation study data follow the first-order reaction rate (R2 > 0.93). Finally, a simple and low-cost synthesis approach, rapid degradation, and outstanding stability of the CQD-coated CZF nanophotocatalyst should make it a potential photocatalyst for dye wastewater treatment.
RESUMO
This study focuses on the solution combustion approach to examine the nanostructures of undoped and doped ZnO with different concentrations of Al (0.1 % and 0.2 %). Various physical techniques were utilized to characterize the synthesized nanoparticles. X-ray diffraction (XRD) revealed the crystalline materials, while scanning electron microscopy (SEM) with energy-dispersive X-ray (EDX) findings confirmed the products with particle size and the insertion of Al into the ZnO lattice. Fourier-transform infrared spectra (FTIR) confirmed the presence of different functional groups in the obtained material. The results indicate that Al-doped ZnO (Al-ZnO) nanoparticles show promising properties for optoelectronics and photoluminescence. Photoluminescence analysis indicated that an increase in Al3+ (0.2 %) concentration resulted in a decrease in peak intensity and an increase in the full width at half maximum. The band gap was calculated using the Taucs plot. The study also highlights the effectiveness of Zn1-xAlxO nanostructures in degrading organic pollutants, particularly in adsorbing Malachite Green (MG) dye. Among the samples, the 0.2 % Al-doped ZnO exhibited superior dye degradation efficiency due to its enhanced adsorption capacity and smaller particle size, as evidenced by multilayer adsorption capacity and chemisorption during the degradation process. This study provides valuable insights into the potential applications of Al-doped ZnO nanoparticles in various environmental and technological fields, emphasizing their significance in the degradation of organic pollutants.
RESUMO
The development of environmentally friendly technology is vital to effectively address the issues related to environmental deterioration. This work integrates ZnO-decorated MoS2 (MZ) to create a high-performing PVDF-based PVDF/MoS2-ZnO (PMZ) hybrid polymer composite film for sonocatalytic organic pollutant degradation. An efficient synergistic combination of MZ was identified by altering the ratio, and its influence on PVDF was assessed using diverse structural, morphological, and sonocatalytic performances. The PMZ film demonstrated very effective sonocatalytic characteristics by degrading rhodamine B (RhB) dye with a degradation efficiency of 97.23%, whereas PVDF only degraded 17.7%. Combining MoS2 and ZnO reduces electron-hole recombination and increases the sonocatalytic degradation performance. Moreover, an ideal piezoelectric PVDF polymer with MZ enhances polarization to improve redox processes and dye degradation, ultimately increasing the degradation efficiency. The degradation efficiency of RhB was seen to decrease while employing isopropanol (IPA) and p-benzoquinone (BQ) due to the presence of reactive oxygen species. This suggests that the active species â¢O2- and â¢OH are primarily responsible for the degradation of RhB utilizing PMZ2 film. The PMZ film exhibited improved reusability without substantially decreasing its catalytic activity. The superior embellishment of ZnO onto MoS2 and effective integration of MZ into the PVDF polymer film results in improved degrading performance.
RESUMO
In this study, we present the synthesis of gold nanoparticles (AuNPs) using a completely green synthesis method without the use of any additional functionalizing agent, except dried turmeric root extract. The significant synthesis parameters were optimized, and the applicability of AuNPs was investigated in areas such as plasmonic and fluorescent sensing of aluminum (Al3âº) and chromium (Cr3âº) ions, reduction of 4-nitrophenol (4-NP), and degradation of methylene blue (MB) and methyl orange (MO) dyes. Characterization studies were performed using UV-Vis spectroscopy, TEM, FTIR, and XRD, revealing that the AuNPs predominantly had a spherical morphology and a very small particle size of 8.5 nm, with stability maintained up to 120 days. The developed AuNP-based plasmonic sensors relied on aggregation-induced decreases in absorption, along with a red shift in the spectra. Fluorescence sensing demonstrated a linear increase in intensity with increasing concentrations of Al3⺠and Cr3âº, with detection limits of 0.83 and 1.19 nM, respectively. The catalytic activities of AuNPs were tested in reducing 4-NP and degradations of MB and MO dyes (binary system) in tap water and wastewater, with the reactions following pseudo-first-order kinetics. This study highlights the potential of AuNPs synthesized from turmeric roots for various environmental and sensing applications.
RESUMO
Sulfate radical-based advanced oxidation processes (SR-AOPs) are renowned for their exceptional capacity to degrade refractory organic pollutants due to their wide applicability, cost-effectiveness, and swift mineralization and oxidation rates. The primary sources of radicals in AOPs are persulfate (PS) and peroxymonosulfate (PMS) ions, sparking significant interest in their mechanistic and catalytic aspects. To develop a novel nanocatalyst for SR-AOPs, particularly for PMS activation, we synthesized carbon-coated FeCo nanoparticles (NPs) using solvothermal methods based on the polyol approach. Various synthesis conditions were investigated, and the NPs were thoroughly characterized regarding their structure, morphology, magnetic properties, and catalytic efficiency. The FeCo phase was primarily obtained at [OH-] / [Metal] = 26 and [Fe] / [Co] = 2 ratios. Moreover, as the [Fe]/[Co] ratio increased, the degree of xylose carbonization to form a carbon coating (hydrochar) on the NPs also increased. The NPs exhibited a spherical morphology with agglomerates of varying sizes. Vibrating-sample magnetometer analysis (VSM) indicated that a higher proportion of iron resulted in NPs with higher saturation magnetization (up to 167.8 emu g-1), attributed to a larger proportion of FeCo bcc phase in the nanocomposite. The best catalytic conditions for degrading 100 ppm Rhodamine B (RhB) included 0.05 g L-1 of NPs, 2 mM PMS, pH 7.0, and a 20-min reaction at 25 °C. Notably, singlet oxygen was the predominant specie formed in the experiments in the SR-AOP, followed by sulfate and hydroxyl radicals. The catalyst could be reused for up to five cycles, retaining over 98% RhB degradation, albeit with increased metal leaching. Even in the first use, dissolved Fe and Co concentrations were 0.8 ± 0.3 and 4.0 ± 0.5 mg L-1, respectively. The FeCo catalyst proved to be effective in dye degradation and offers the potential for further refinement to minimize Co2+ leaching.
Assuntos
Nanocompostos , Peróxidos , Nanocompostos/química , Peróxidos/química , Poluentes Químicos da Água/química , Catálise , Oxirredução , Ferro/química , Carbono/químicaRESUMO
Assembling microscopic metal-organic frameworks into macroscopic polymeric scaffolds to develop highly renewable materials has been a promising yet challenging area of research. Herein, chitosan (CS) blended with nano-cellulose (NC) was unidirectionally transformed into an aerogel with oriented macropores and then biomineralized with zeolite imidazolate frameworks-8 (ZIF-8) to form a hierarchical structured chitosan-nanocellulose/zeolite imidazolate frameworks-8 (CS-NC-ZIF-8) hybrid aerogel. Incorporating ZIF-8 significantly increases the versatility and mechanical strength with a Young's modulus of 14.18 MPa of the CS-NC aerogel. The incorporation of ZIF-8 into the aerogel not only enhances its adsorption capacity for methylene blue, rhodamine B, acid fuchsin, and methyl orange, but also facilitates the generation of electrons from water that can be transferred to degrade > 90 % of malachite green within 90 min in each catalytic cycle, and this capability was maintained for at least 10 consecutive cycles. Remarkably, the hybrid aerogel was highly renewable after the adsorption of cationic dyes and catalytic removal of malachite green. With its facile production process, high removal efficiency, affordable and green nature, and excellent regeneration feasibility, the CS-NC-ZIF-8 aerogel stands as a promising solution for addressing challenges associated with dye-contaminated water treatment.
RESUMO
Piezo-photocatalysis combines photocatalysis and piezoelectric effects to enhance catalytic efficiency by creating an internal electric field in the photocatalyst, improving carrier separation and overall performance. This study presents a high-performance piezo-photocatalyst for efficient dye degradation using a synergistic barium titanate (BTO)-MXene composite. The composite was synthesized via a facile method, combining the unique properties of BTO nanoparticles with the high conductivity of MXene. The structural and morphological analysis confirmed the successful formation of the composite, with well-dispersed BTO nanoparticles on the MXene surface. The piezo-photocatalytic activity of the composite was evaluated using a typical dye solution (Rhodamine B: RhB) under ultraviolet irradiation and mechanical agitation. The results revealed a remarkable enhancement in dye degradation (90 % in 15 min for piezo-photocatalysis) compared to individual stimuli (58.2 % for photocatalysis and 95.8 % in 90 min for piezocatalysis), highlighting the synergistic effects between BTO and MXene. The enhanced catalytic performance was attributed to the efficient charge separation and transfer facilitated by the composite's structure, leading to increased reactive species generation and dye molecule degradation. Furthermore, the composite exhibited excellent stability and reusability, showcasing its potential for practical applications in wastewater treatment. Overall, this work represents a promising strategy for designing high-performance synergistic catalysts, addressing the pressing need for sustainable solutions in environmental remediation.
RESUMO
GaN is more stable than most metal oxide semiconductors for the photocatalytic degradation of organic pollutants in harsh conditions, while its catalytic efficiency has been difficult to be substantially improved. In this study, the tribocatalytic degradation of organic dyes by GaN nanoparticles has been investigated. Stimulated through magnetic stirring using homemade Teflon magnetic rotary disks in glass beakers, the GaN nanoparticles were found to induce negligible degradation in rhodamine B (RhB) and methyl orange (MO) solutions. Surprisingly, the degradation was greatly enhanced in beakers with Ti and Al2O3 coatings on their bottoms: 99.2% and 99.8% of the 20 mg/L RhB solutions were degraded in 3 h for the Ti and Al2O3 coatings, respectively, and 56% and 60.2% of the 20 mg/L MO solutions were degraded in 24 h for the Ti and Al2O3 coatings, respectively. Moreover, the MO molecules were only broken into smaller organic molecules for the Ti coating, while they were completely degraded for the Al2O3 coating. These findings are important for the catalytic degradation of organic pollutants by GaN in harsh environments and for achieving a better understanding of tribocatalysis as well.
RESUMO
The catalytic capabilities of metals in degrading azo dyes have garnered extensive interest; however, selecting highly efficient metals remains a significant challenge. We have developed a Zn-Ca-based metallic glass composite which shows outstanding degradation efficiency for Direct Blue 6. This alloy comprises a Zn2Ca crystalline phase and an amorphous matrix, allowing for the degradation of azo dyes within minutes in a wide temperature range of 0-60 °C. Kinetic calculations reveal an exceptionally low activation energy of 8.99 kJ/mol. The rapid degradation is attributed to the active element Ca and the unique amorphous structure of the matrix, which not only facilitates abundant redox conditions but also minimizes the hydrolysis of the active element. The newly developed metallic glass composite exhibits a notably higher azo dye degradation rate compared to those of general metallic glasses, offering a new avenue for the rapid degradation of azo dyes. This paper holds significant importance for the development of novel azo dye wastewater treatment agents.
RESUMO
The shaping of covalent organic frameworks (COFs) from non-processible powder forms into applicable architectures with additional functionality remains a challenge. Using pre-electrospun polymer fibers as a sacrificial template, herein, we report a green synthesis of an architecture in the form of COF hollow fibers with an inner layer of peroxidase-like iron oxide nanoparticles as a catalytic material. When compared to peroxidase-like pristine iron oxide nanoparticles, these COF hollow fibers demonstrate higher catalytic breakdown of crystal violet due to their peroxidase-like activity via advanced oxidation process. Furthermore, as a potential adsorbent, hollow COF fibers exhibit significantly effective adsorption capacity and removal efficiency of organic solvent and oil from water. Because of their magnetic nature, COF hollow fibers can be easily recovered and have exhibited high recycling stability for both catalytic dye degradation and organic solvent removal from water.
RESUMO
Water pollution caused by dyes and industrial wastewater poses a significant threat to ecosystems. The purification of such pollutants presents a major challenge. Photocatalysis based on semiconductor materials is a potential wastewater treatment process due to its safety and cost-effectiveness. In the present work, Zn1-2xCexDyxO (x = 0.01-0.05) semiconductors were prepared by the sol-gel auto-ignition method. The samples are denoted CDZO1, CDZO3, and CDZO5 for x = 0.01-0.05, respectively. The X-ray diffraction and Raman spectroscopy results revealed the formation of ZnO hexagonal phase wurtzite structure for all synthesized compositions. Different structural properties were determined. It was found that the lattice parameters and the unit cell volume increased, while the crystallite size diminished as x varied from 0.01 to 0.05. Transmission electron microscopy observations confirmed the formation of nanoparticles with the desired chemical compositions. The specific surface area (SSA) values are found to be 39.95 m2/g, 48.62 m2/g, and 51.36 m2/g for CDZO1, CDZO5, and CDZO5 samples, respectively. The reflectance spectra were recorded to examine the optical properties of the different nanoparticles. The values of the optical band gap were 3.221, 3.225, and 3.239 eV for CDZO1, CDZO3, and CDZO5 samples, respectively. In addition, the photocatalytic performance towards RhB dye degradation for the different samples was assessed. It was established that the CDZO3 sample with a moderate SSA value exhibited the superior photocatalytic performance among the other as-prepared samples wherein the percentage of degradation efficiency, and kinetic constant rate attained their maximum values of 98.22 % and 0.0521 min-1, respectively within 75 min. As per the obtained findings, it is evident that the Zn1-2xCexDyxO photocatalyst has prominent potential for use in the degradation of dyes and offers a useful route for impeding the recombination of electron-hole pairs of zinc oxide material.
RESUMO
Industrial dye degradation involves several processes by which dyes are broken down, ideally into innocuous products. Methylene blue (MB) is one of the most commonly employed dyes in the textile industry and is released into water in routine industry processes. These discharges lead to creating a nocuous nature for humans and animals. Drugs are also discharged into water bodies from various pharmaceutical industries. In these two contexts, in the present work, the green synthesis of calcium-doped zinc oxide nanoparticles (Ca-doped ZnO NPs) is achieved using the aqueous peel extract of Citrus limetta by the solution combustion technique. The structural, morphological, and optical properties of the synthesized Ca-doped ZnO NPs are investigated using XRD, FTIR, SEM, EDX, and UV-visible spectroscopy. The prepared NPs were subjected to photocatalytic degradation of MB dye under visible-light illumination, which shows ~ 95% dye degradation. The synthesized Ca-doped ZnO NPs were also employed to adsorb tinidazole (TDZ), a nitroimidazole antibiotic, from water samples. An excellent adsorptive capacity of the NPs was observed for selectively adsorbing the TDZ ~ 96.2%. The drug TDZ was found to have pseudo-second-order kinetics. The catalyst recycling proved its repeatability; removal of the dye reached up to 92% after three successive usages. Therefore, using waste Citrus limetta peel extract, the multifunctional Ca-doped ZnO NPs were synthesized, which maintained effective adsorption potential and photocatalytic abilities and could be used as an effective material for environmental remediation.
Assuntos
Azul de Metileno , Tinidazol , Poluentes Químicos da Água , Óxido de Zinco , Óxido de Zinco/química , Poluentes Químicos da Água/química , Poluentes Químicos da Água/análise , Azul de Metileno/química , Tinidazol/química , Adsorção , Corantes/química , Cálcio/química , Cálcio/análise , Eliminação de Resíduos Líquidos/métodos , Citrus/química , Nanopartículas Metálicas/química , Nanopartículas/químicaRESUMO
We have adopted a novel CeO2/Bi2MoO6/g-C3N4-based ternary nanocomposite that was synthesized via hydrothermal technique. The physiochemical characterization of as-prepared samples was examined through various analytical techniques such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy TEM, photoluminescent spectra (PL), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller (BET), and ultraviolet diffuse reflectance spectroscopy (UV-DRS) technique. In addition, the photocatalytic performance was carried out by degradation of Rhodamine B dye under visible light irradiation using this nanocatalyst. The ternary nanocomposite achieved 94% of the degradation efficiency within 100 min which is higher than the pristine and binary composites under the predetermined condition pH = 7, Rhodamine B dye = 5 mg/L, and catalyst concentration = 150 mg/L. The experimental synergetic effect of CeO2/Bi2MoO6/g-C3N4 ternary nanocomposite has been ascribed to the interfacial charge carrier migration between CeO2, Bi2MoO6, and g-C3N4. The optical absorption range of CeO2/Bi2MoO6/g-C3N4 ternary nanocomposite was enhanced, and the band gap was reduced up to 2.2 eV. In addition, scavenger trapping experiment proves that the super oxide anions (O2-.) and photogenerated holes are the major active species. The reusability and stability experiment proved the CeO2/Bi2MoO6/g-C3N4 ternary nanocomposite keeps good durability during the photocatalytic degradation process after the five successive cycles. Furthermore, based on the results, the charge carrier transfer photocatalytic mechanism was also discussed. This CeO2/Bi2MoO6/g-C3N4 ternary nanocomposite may offer the cheapest material and extend the great opportunity for clean and environmental remediation approach under the visible light irradiation.
Assuntos
Cério , Rodaminas , Rodaminas/química , Cério/química , Catálise , Nanosferas/química , Bismuto/química , Poluentes Ambientais/química , Nanocompostos/química , Molibdênio/químicaRESUMO
MgFe2O4@ZnAl2O4 magnetic nanocomposites were synthesized with the easy and green sol-gel method, and their photocatalytic efficiency was followed toward degradation of reactive blue 222 (RB222) dye under visible light irradiation. Prepared nanocomposites were fully characterized. The SEM and TEM images revealed the spherical morphology of the produced nanocomposites, with average size of 20-25 nm. The XRD pattern of sample exhibited the successful synthesis of the MgFe2O4@ZnAl2O4 MNCs with crystallite size 13 nm. The saturation magnetization (Ms) of the nanocomposites was examined using VSM, indicating a value of 6.59 emu/g. The absence of Hc and Mr values confirms the superparamagnetic nature of the nanoparticles. In addition, the surface area was calculated to be 78.109 m2/g utilizing BET analysis, and the band gap was determined to be 1.88 eV by DRS analysis. The photocatalytic, photolysis, and adsorption performance were investigated and result shown photodegradation activity was higher than others. These results confirm the synergetic effect between the MgFe2O4@ZnAl2O4 MNCs and visible light irradiation to degradation of organic dye. The results indicate that rapid degradation of 96% of RB222 dye occurred in just 10 min, with a TOC removal rate of approximately 59%. Furthermore, radical scavenger agents also clarified photodegradation of RB222 dye.
RESUMO
Biosynthetic metals have attracted global attention because of their safety, affordability, and environmental friendliness. As a consequence, the cell-free filtrate (CFF) of Dill leaf-derived endophytic fungus Aspergillus luchuensis was employed for the extracellularly synthesis silver nanoparticles (AgNPs). A reddish-brown color shift confirmed that AgNPs were successfully produced. The obtained AgNPs were characterized by UV-Vis (ultraviolet-visible spectroscopy), Transmission electron microscopy (TEM), FTIR, EDX, and zeta potential. Results demonstrated the creation of crystalline AgNPs with a spherical shape at 427.81 nm in the UV-Vis spectrum, and size ranged from 16 to 18 nm as observed by TEM. Additionally, the biogenic AgNPs had a promising antibacterial activity versus multidrug-resistant bacteria, notably, S. aureus, E. coli, and S. typhi. The highest growth reduction was recorded in the case of E. coli. Furthermore, the biosynthesized AgNPs demonstrated potent antifungal potential versus a variety of harmful fungi. The maximum growth inhibition was evaluated from A. brasinsilles, followed by C. albicans as compared to cell-free extract and AgNO3. In addition, data revealed that AgNPs possess powerful antioxidant activity, and their ability to scavenge radicals increased from 33.0 to 85.1% with an increment in their concentration from 3.9 to 1,000 µg/mL. Furthermore, data showed that AgNPs displayed high catalytic activity of safranin under light irradiation. The maximum decolorization percentage (100%) was observed after 6 h. Besides, the biosynthesized AgNPs showed high insecticidal potential against 3rd larval instar of Culex pipiens. Taken together, data suggested that endophytic fungus, A. luchuensis, is an attractive candidate as an environmentally sustainable and friendly fungal nanofactory.
RESUMO
Metallic glass is being gradually recognized for its unique disordered atomic configuration and excellent catalytic activity, so is of great significance in the field of catalysis. Recent reports have demonstrated that Fe-based metallic glass, as a competitive new catalyst, has good catalytic activity for the fields of environment and energy, including high catalytic efficiency and stability. This review introduces the latest developments in metallic glasses with various atomic components and their excellent catalytic properties as catalysts. In this article, the influence of Fe-based metallic glass catalysts on the catalytic activity of dye wastewater treatment and water-splitting is discussed. The catalytic performance in different atomic composition systems and different water environment systems, and the preparation parameters to improve the surface activity of catalysts, are reviewed. This review also describes several prospects in the future development and practical application of Fe-based metallic glass catalysts and provides a new reference for the synthesis of novel catalysts.
RESUMO
ZnO/layered carbon nanocomposites with varied sizes of ZnO nanoparticles (NPs) were synthesized by mechanical milling of mixture of ZnO NPs and carbon NPs. The NP size of ZnO was controlled with average particle sizes about 19.33, 21.87, 24.21, and 27.89 nm by varying the concentrations of carbon NPs viz 0, 2, 5, and 10 weight percent, respectively, in the mixture. Presence of carbon with ZnO in the form of composite also resulted in the enhanced shift of the band gap of ZnO due to the optical transitions in the impurity states or presence of carbon as compared to the ZnO size change alone. Additionally, the enhancement of absorbance in the visible region with an increase in carbon content was observed. Such an increase in absorbance can enhance the photocatalytic activity of ZnO NPs. Raman bands for ZnO NPs also were found to shift faster in the presence of layered carbon. The quenching of visible photoluminescence emission of ZnO NPs with an increase in concentration of carbon NPs in the composite indicated the phenomenon associated with transfer of electrons from ZnO to layered carbon helping the separation of photo-generated electrons and holes in ZnO and can lead to enhancement of the photocatalytic activity of ZnO NPs. In the photocatalytic studies, it was observed that the degradation of methylene blue (MB) dye was significantly enhanced by the increase of content of layered carbon in the nanocomposite. The sample containing 10% carbon showed the highest adsorption in dark conditions which was up to 60% of the starting strength and this was further enhanced to 88% in the presence of UV radiation. Enhanced adsorption of MB dye and the effective separation of electron-hole pairs due to charge transfer were believed to be the main causes behind such kind of improvement in the photocatalytic effects.
RESUMO
The release of organic pollutants and dyes into the environment by industries has had profound and harmful effects on both humans and ecosystems. Graphene oxide (GO) and its reduced form have been investigated for their effectiveness in removing pollutant dyes. GO nano-powder was synthesized using an improved version of Hummer's method and subsequently thermally reduced at various temperatures, including 125, 150, 175, and 200 °C, under vacuum conditions. In the X-ray diffraction spectra, an intense (001) diffraction peak was initially observed at 9.136° (2θ) for pristine GO. This peak gradually shifted towards higher angles as the reduction process took place and eventually disappeared when the GO was reduced at 200 °C. The intensity ratio of the D and G bands (ID/IG ratio) for GO nano-powder in the Raman spectra decreased from 0.94 to 0.76 due to the reduction process. The FTIR spectra of GO and reduced graphene oxide (rGO) also illustrated the reduction process. The bandgap of pristine GO significantly decreased from 2.31 to 0.73 eV, as determined by ultraviolet-visible (UV-Vis) diffuse reflectance spectrophotometry during the reduction process. The surface area and pore volume of both pristine GO and rGO-150 were determined using the BET (Brunauer-Emmett-Teller) and BJH (Barrett-Joyner-Halenda) methods. The results indicated an increase in the BET surface area from 6.61 to 7.86 m2/g and a corresponding enhancement in pore volume from 0.118 to 0.128 cc/g after reduction. The adsorption and photocatalytic degradation behavior of pristine GO and reduced graphene oxides (rGOs) were examined using methylene blue dye. The pristine GO demonstrated impressive adsorption capability, effectively removing the dye by 85.78 % within just 15 min and achieving nearly 97 % removal after 4 h. In contrast, the highest photocatalytic degradation of methylene blue, about 47.58 %, was attained for the rGO sample reduced at 150 °C under the illumination of visible light.