Evaluation of asphalt mixtures modified with low-density polyethylene and high-density polyethylene using experimental results and machine learning models.

The widespread use of low-density polyethylene (LDPE) and high-density polyethylene (HDPE) plastics has resulted in a large amount of waste plastic that requires appropriate disposal or reuse. One potential solution is to use them in the modification of asphalt concrete (AC) mixtures for more sustainable highways. To study this possibility, permanent deformation and dynamic modulus (DM) of the LDPE and HDPE modified AC mixtures was investigated by conducting flow number (FN), flow time (FT) and DM tests on Superpave gyratory compacted specimens. Machine learning models; multi-layer perceptron (MLP), radial basis function neural network (RBFNN), generalized regression neural network (GRNN) and support vector machine (SVM) were used to predict the DM on the basis of frequency and temperature parameters. The model's performance was gauged by analyzing the root mean square error, mean relative error, and coefficient of determination. The study findings revealed that the LDPE and HDPE modified AC mixtures provide 2.07 times and 1.27 times better resistance to permanent deformation, respectively, than their counterpart. It was also found that the LDPE and HDPE modified AC mixtures have 2.1 times and 1.4 times higher DM values, respectively, than the Control AC mixtures. Among the machine learning models, MLP (R2 = 0.98) showed best accuracy in predicting DM and thus is recommended to be used in similar studies due to its robustness. Additionally, the feature importance analysis revealed that frequency has the highest impact on DM predictions, followed by temperature and the inclusion of the LDPE.

Study on the Effect of Hot and Humid Environmental Factors on the Mechanical Properties of Asphalt Concrete.

To investigate the effect of hot and humid environmental factors on the mechanical properties of asphalt mixtures research, in this paper, the dynamic modulus of asphalt mixtures under the effects of aging, dry-wet cycling, and coupled effects of aging and dry-wet cycling were measured by the simple performance tester (SPT) system, and the dynamic modulus principal curves were fitted based on the sigmoidal function. The results show that under the aging effect, the dynamic modulus of asphalt mixture increases with the aging degree; the dynamic modulus of short-term aged, medium-term aged, long-term aged, and ultra-long-term aged asphalt mixtures increased by 9.3%, 26.4%, 44.8%, and 57%, respectively, compared to unaged asphalt mixtures at 20 °C and 10 Hz; the high-temperature stability performance is enhanced, and the low temperature cracking resistance performance is enhanced; under the dry-wet cycle, the aging effect of asphalt water is more obvious in the early stage, and dynamic modulus of resilience of the mixture is slightly increased. In the long-term wet-dry cycle process, water on the asphalt and aggregate erosion increased, the structural bearing capacity attenuation, and the dynamic modulus of rebound greatly reduced at 20 °C and 10 Hz. For example, the dynamic modulus of asphalt mixtures with seven wet and dry cycles increased by 3% compared to asphalt mixtures without wet and dry cycles, and the dynamic modulus of asphalt mixtures with 14 cycles of wet and dry cycles and 21 cycles of wet and dry cycles decreased by 10.8% and 16.5%, respectively, compared to asphalt mixtures without wet and dry cycles. The main curve as a whole shifted downward; the high-temperature performance decreased significantly; in the aging wet-dry cycle coupling, the aging asphalt mixture is more susceptible to water erosion, and the first wet-dry cycle after the mix by the degree of water erosion is relatively small, along with the dynamic modulus of rebound. The dynamic modulus of resilience is relatively larger, and the high-temperature performance is relatively better, while the low-temperature performance is worse.

Evaluating and optimizing NBR-modified bituminous mixes: a rheological and RSM-based study.

Bitumen shows visco-elastic behavior, exhibiting both elastic and viscous properties as predicted by dynamic response and phase angle. Modern asphalt bituminous pavements face issues such as early-stage fatigue cracks, rutting, and permanent deformations due to low-temperature cracking, high-temperature deformation, moisture susceptibility, and overloading. These pavement distresses result in the formation of potholes, alligator cracks, and various deformations, which accelerate the need for rehabilitation and maintenance. To address these concerns, this study focused on utilizing Nitrile Butadiene Rubber derived from surgical gloves as an additive in conventional asphalt pavements to assess its effect on stiffness. Nitrile Butadiene Rubber was added in intervals of 2%, 4%, 6%, and 8% to conventional bituminous pavement. The rheological properties, marshall properties, dynamic modulus, and phase angle were evaluated for varying percentages of Nitrile Butadiene Rubber at different temperature, and frequency. The dynamic response was determined using a simple performance tester at four different temperatures (4.4 °C, 21.1 °C, 37.8 °C, and 54.4 °C) and six different frequencies (0.1, 0.5, 1, 5, 10, and 25 Hz). Response surface methodology was employed to establish a relationship between input and output variables and to optimize the amount of Nitrile Butadiene Rubber in the mix based on dynamic modulus and phase angle. The study concluded that adding up to 6% of Nitrile Butadiene Rubber improved Marshall stability, while higher percentages led to reduced stability. A similar trend was observed in the dynamic modulus, which peaked with the addition of 6% Nitrile Butadiene Rubber, regardless of frequency and temperature. The response surface methodology model indicated that coupling the percentage of Nitrile Butadiene Rubber with frequency increased the dynamic modulus at a constant temperature, with the highest value occurring at 4.4 °C. However, the dynamic modulus decreased as the temperature rose for the same combinations of Nitrile Butadiene Rubber percentages and frequencies. Numerical optimization suggested that a maximum of 5.9% Nitrile Butadiene Rubber should be added to achieve the highest dynamic modulus and lowest phase angle.

Study on the Application of Kramers-Kronig Relation for Polyurethane Mixture.

Polyurethane (PU) mixture, which is a new pavement mixture, exhibits different dynamic properties compared to a hot-mixed asphalt mixture (HMA). This paper analyzed whether the Kramers-Kronig (K-K) relation and thermorheologically simple properties applied to the PU mixture. Based on the results, the PU mixture exhibited thermorheologically simple properties within the test conditions. The time-temperature superposition principle (TTSP) was applicable for the PU mixture to construct a dynamic modulus master curve using the standard logistic sigmoidal (SLS) model, the generalized logistic sigmoidal (GLS) model, and the Havriliak-Negami (HN) model. The Hilbert integral transformed SLS and GLS models for the phase angle can accurately fit the measured phase angle data with newly fitted shift factors and predict the phase angle within the viscoelastic range. The core-core and black space diagrams both displayed single continuous smooth curves, which can be utilized to characterize the viscoelastic property of the PU mixture. The K-K relation is applicable for the PU mixture to obtain the phase angle master curve model, storage modulus, and loss modulus from the complex modulus test results with the test temperatures and loading frequencies. The phase angle of the PU mixture at extremely high or low test temperatures cannot be derived from the dynamic modulus data.

Investigation of Dynamic Viscoelastic Characteristics of Permeable Asphalt.

In order to provide a basis for the structural analysis, design and maintenance of permeable asphalt pavements, and to promote their engineering promotion and application, this study investigated the dynamic viscoelastic properties of permeable asphalt mixtures (PAC-13) under complex stress states. A Simple Performance Tester (SPT) system was used to measure the dynamic modulus of the mix under complex stress states. The displacement factor and principal dynamic modulus curves were formed by fitting Sigmoidal functions and using 1stOpt (first optimization) software, the phase angle principal curves were further determined, and the dynamic modulus was predicted for the ambient phase (15-25 °C) using the Hirsch model. The results showed that the dynamic modulus of the mixtures decreases with an increasing temperature, and the maximum decrease in the dynamic modulus is 93% when the confining pressure is 100 kPa and the loading frequency is 10 Hz. The dynamic modulus increases with an increasing confining pressure and loading frequency, the maximum increase with an increasing confining pressure is 26.1% when the temperature is 25 °C and the loading frequency is 10 Hz, and the maximum increase with an increasing loading frequency is 411% when the temperature is 25 °C and the confining pressure is 100 Hz. The dynamic modulus has a strong frequency dependence at low temperatures, while it is stress-dependent at high temperatures. Meanwhile, based on the Hirsch model, a new modified prediction model was developed, which can well predict the dynamic modulus of permeable asphalt mixtures at room temperature.

Passive elasticity properties of Octopus rubescens arms.

In this report, passive elasticity properties of Octopus rubescens arm tissue are investigated using a multidisciplinary approach encompassing biomechanical experiments, computational modeling, and analyses. Tensile tests are conducted to obtain stress-strain relationships of the arm under axial stretch. Rheological tests are also performed to probe the dynamic shear response of the arm tissue. Based on these tests, comparisons against three different viscoelasticity models are reported.

Site-specific elastic and viscoelastic biomechanical properties of healthy and osteoarthritic human knee joint articular cartilage.

Articular cartilage exhibits site-specific biomechanical properties. However, no study has comprehensively characterized site-specific cartilage properties from the same knee joints at different stages of osteoarthritis (OA). Cylindrical osteochondral explants (n = 381) were harvested from donor-matched lateral and medial tibia, lateral and medial femur, patella, and trochlea of cadaveric knees (N = 17). Indentation test was used to measure the elastic and viscoelastic mechanical properties of the samples, and Osteoarthritis Research Society International (OARSI) grading system was used to categorize the samples into normal (OARSI 0-1), early OA (OARSI 2-3), and advanced OA (OARSI 4-5) groups. OA-related changes in cartilage mechanical properties were site-specific. In the lateral and medial tibia and trochlea sites, equilibrium, instantaneous and dynamic moduli were higher (p < 0.001) in normal tissue than in early and advanced OA tissue. In lateral and medial femur, equilibrium, instantaneous and dynamic moduli were smaller in advanced OA, but not in early OA, than in normal tissue. The phase difference (0.1-0.25 Hz) between stress and strain was significantly smaller (p < 0.05) in advanced OA than in normal tissue across all sites except medial tibia. Our results indicated that in contrast to femoral and patellar cartilage, equilibrium, instantaneous and dynamic moduli of the tibia and trochlear cartilage decreased in early OA. These may suggest that the tibia and trochlear cartilage degrades faster than the femoral and patellar cartilage. The information is relevant for developing site-specific computational models and engineered cartilage constructs.

Hyperlipidemia Induced Pathological Changes with no Effect in Biomechanical Properties in the Achilles Tendon of Young Swine.

Hyperlipidemia is linked to atherosclerosis and various diseases. Its strong association with Achilles tendinopathies and xanthomas affects tendon properties through lipid deposition in tendon tissue. We examined the impact of hyperlipidemia on the biomechanical properties of the swine Achilles tendons. Swines were fed a high-cholesterol-high-fat diet to induce hyperlipidemia, and their Achilles tendons were collected and examined for biomechanical properties. The ultimate tensile strength, modulus of elasticity and viscoelastic properties did not exhibit significant differences between hyperlipidemic and control swines. H&E and pentachrome staining revealed extracellular matrix (ECM) disorganization and cellular infiltration in the hyperlipidemic swines, highlighting a marked difference between the control and hyperlipidemic groups. These results suggest hyperlipidemia in young swines alters the tendon composition and may contribute to weak biomechanical properties with time.

Sustainable Asphalt Mixtures with Enhanced Water Resistance for Flood-Prone Regions Using Recycled LDPE and Carnauba-Soybean Oil Additive.

This manuscript presents a comprehensive study on the sustainable optimization of asphalt mixtures tailored for regions prone to flooding. The research addresses the challenges associated with water damage to asphalt pavements by incorporating innovative additives. The study centers on incorporating recycled Low-Density Polyethylene (LDPE) and a tailored Carnauba-Soybean Oil Additive, advancing asphalt mixtures with a Control mix, LDPE (5%) + Control, and LDPE (5%) + 3% Oil + Control. A critical aspect of the research involves subjecting these mixtures to 30 wetting and drying cycles, simulating the conditions prevalent in tropical flood-prone areas. The incorporation of innovative additives in asphalt mixtures has demonstrated significant improvements across various performance parameters. Tensile Strength Ratio (TSR) tests revealed enhanced tensile strength, with the LDPE (5%) + 3% Oil-modified mixture exhibiting an impressive TSR of 85.7%. Dynamic Modulus tests highlighted improved rutting resistance, showcasing a remarkable increase to 214 MPa in the LDPE (5%) with a 3% Oil-modified mixture. The Semi-Circular Bending (SCB) test demonstrated increased fracture resistance and energy absorption, particularly in the LDPE (5%) with 3% Oil-modified mixture. Hamburg Wheel-Tracking (HWT) tests indicated enhanced moisture resistance and superior rutting resistance at 20,000 cycles for the same mixture. Cantabro tests underscored improved aggregate shatter resistance, with the LDPE (5%) + 3% Oil-modified mixture exhibiting the lowest weight loss rate at 9.820%. Field tests provided real-world insights, with the LDPE (5%) + 3% Oil mixture displaying superior stability, a 61% reduction in deflection, and a 256% improvement in surface modulus over the control mixture. This research lays the groundwork for advancing the development of sustainable, high-performance road pavement materials, marking a significant stride towards resilient infrastructure in flood-prone areas.

Sensitivity and Reliability Analysis of Ultrasonic Pulse Parameters in Evaluating the Laboratory Properties of Asphalt Mixtures.

The ultrasonic test is a promising non-destructive testing technique for evaluating the properties of asphalt mixtures. To investigate the applicability and reliability of ultrasonic testing technology (UTT) in evaluating the performance of asphalt mixtures, ultrasonic tests, indirect tensile tests, compression tests, and dynamic modulus tests were carried out at various temperatures. Subsequently, the distribution characteristics of ultrasonic traveling parameters for asphalt mixtures were analyzed. The variation of ultrasonic pulse velocity and amplitude in dry and wet states with temperature was studied. Then, the correlation between the ultrasonic parameters and both the volume parameters and the mechanical performance parameters of asphalt mixtures was revealed, and the functional relationship between ultrasonic pulse velocity and compressive strength was established. Finally, the reliability of predicting high-frequency dynamic modulus by ultrasonic velocity was verified. The laboratory tests and analysis results indicate that both ultrasonic pulse velocity and amplitude in dry and wet conditions show a decreasing trend with an increase in temperature. Ultrasonic parameters are greatly influenced by asphalt content and mineral aggregate content of 9.5~13.2 mm and 13.2~16 mm. The dynamic modulus at a high-frequency load can be predicted by using ultrasonic velocity, and predicting the results for OGFC and SMA mixtures deduced by using the UPV at a high-frequency load have higher reliability.

Hyperlipidemia Lowers the Biomechanical Properties of Rotator Cuff Tendon.

Infraspinatus tendon is the most affected tendon of the rotator cuff, being an important posterior component of the shoulder joint. Hyperlipidemia is a predisposing factor in the progression of rotator cuff tears and retear. We studied the effect of hyperlipidemia on the biomechanical properties of rotator cuff tendons. The infraspinatus tendon of the rotator cuff from hyperlipidemic swine were collected and tested for ultimate tensile strength (UTS) and modulus of elasticity. Dynamic mechanical analysis was performed to examine viscoelastic properties. The findings revealed no significant difference in UTS but had significantly lower modulus of elasticity in the infraspinatus tendon of the hyperlipidemic group compared to the control group. Moreover, differences in the dynamic modulus, storage modulus, and loss modulus were not statistically significant between the hyperlipidemic and control swine. There was no difference in water content between the groups but the hyperlipidemic group had fatty infiltration aiding the initial decrease in mechanical properties. These findings suggest an association between fat deposition and early changes in the biomechanical properties of the tendons in the shoulder rotator cuff in hyperlipidemic state.

Investigation of the Relationship between Permanent Deformation and Dynamic Modulus Performance for Bearing-Layer Asphalt Mixture.

Of major concern is the lack of correlation between the material design and structural function of asphalt pavement in China. The objective of this paper is to identify the layer in asphalt pavement where permanent deformation occurs most seriously and to propose a control index for that layer's asphalt mixture. The permanent deformation of each layer was determined through the utilization of thickness measurements obtained from field cores. The results indicate that the reduction in thickness is more significant in the driving lane than in the ridge band and shoulder. This phenomenon can be attributed to the intensified densification and shearing deformation that arise from the combined impacts of recurrent axle loads and high temperatures. Compared to surface and base layers, the bearing layer is the primary area of concern for permanent deformation in asphalt pavement. Therefore, it is imperative to incorporate the ability of bearing-layer asphalt mixture to withstand permanent deformation as a crucial design parameter. The dynamic modulus of the bearing-layer asphalt mixture is significantly influenced by the type of asphalt, gradation, and asphalt content, compared to other design parameters. Based on the relationship established between dynamic modulus and dynamic stability, with creep rate as the intermediate term, a control standard was proposed to evaluate the permanent deformation of the bearing-layer asphalt mixture. This study can provide reasonable and effective guidance for prolonging pavement life and improving pavement performance.

Fabrication and rheological properties of a novel interpenetrating network hydrogel based on sage seed hydrocolloid and globulin from the hydrocolloid extraction by-product.

In this study, interpenetrating polymer network hydrogels were developed based on sage seed gum (SSG) and globulin protein (Glo) extracted from the mucilage-free seeds. By combining Glo hydrogel with the SSG network the inherent weak gelation of the single SSG system was compensated. As the fraction of Glo increased, various properties of the interpenetrating polymer network (IPN) hydrogels improved substantially. Electrophoretic analysis under reducing conditions showed that Glo dissociated into subunits of approximately 30 kDa and 20 kDa, suggesting it comprises 11S globulin. FTIR spectrum revealed new peaks at 1645 cm-1 and 1537 cm-1 in the amide I and II regions, respectively, for the IPN hydrogels, indicating interactions between two hydrogel networks. Based on the weight loss measurements, the IPN hydrogels exhibited lower mass loss, particularly at higher Glo fractions up to 6 %. The IPN hydrogels also displayed enhanced elasticity, pseudoelasticity, thixotropy, and creep resistance compared to SSG hydrogel, indicating suitability for food, pharmaceutical, and biomedical applications. More broadly, this research provides a sustainable strategy toward innovative material development while advancing bio-based hydrogels.

Tensile energy dissipation and mechanical properties of the knee meniscus: relationship with fiber orientation, tissue layer, and water content.

Introduction: The knee meniscus distributes and dampens mechanical loads. It is composed of water (∼70%) and a porous fibrous matrix (∼30%) with a central core that is reinforced by circumferential collagen fibers enclosed by mesh-like superficial tibial and femoral layers. Daily loading activities produce mechanical tensile loads which are transferred through and dissipated by the meniscus. Therefore, the objective of this study was to measure how tensile mechanical properties and extent of energy dissipation vary by tension direction, meniscal layer, and water content. Methods: The central regions of porcine meniscal pairs (n = 8) were cut into tensile samples (4.7 mm length, 2.1 mm width, and 0.356 mm thickness) from core, femoral and tibial components. Core samples were prepared parallel (circumferential) and perpendicular (radial) to the fibers. Tensile testing consisted of frequency sweeps (0.01-1Hz) followed by quasi-static loading to failure. Dynamic testing yielded energy dissipation (ED), complex modulus (E*), and phase shift (δ) while quasi-static tests yielded Young's Modulus (E), ultimate tensile strength (UTS), and strain at UTS (εUTS). To investigate how ED is influenced by the specific mechanical parameters, linear regressions were performed. Correlations between sample water content (φw) and mechanical properties were investigated. A total of 64 samples were evaluated. Results: Dynamic tests showed that increasing loading frequency significantly reduced ED (p < 0.05). Circumferential samples had higher ED, E*, E, and UTS than radial ones (p < 0.001). Stiffness was highly correlated with ED (R2 > 0.75, p < 0.01). No differences were found between superficial and circumferential core layers. ED, E*, E, and UTS trended negatively with φw (p < 0.05). Discussion: Energy dissipation, stiffness, and strength are highly dependent on loading direction. A significant amount of energy dissipation may be associated with time-dependent reorganization of matrix fibers. This is the first study to analyze the tensile dynamic properties and energy dissipation of the meniscus surface layers. Results provide new insights on the mechanics and function of meniscal tissue.

Effect of Moisture Condition of Structural Lightweight Concretes on Specified Values of Static and Dynamic Modulus of Elasticity.

The dynamic modulus of elasticity (Ed), specified by ultrasonic pulse velocity measurements, is often used, especially for concrete built into construction, to estimate the static modulus of elasticity (Ec,s). However, the most commonly used Equations for such estimations do not take into account the influence of concrete moisture. The aim of this paper was to establish this influence for two series of structural lightweight aggregate concrete (LWAC) varying in their strength (40.2 and 54.3 MPa) and density (1690 and 1780 kg/m3). The effect of LWAC moisture content turned out to be much more pronounced in the case of dynamic modulus measurements than for static ones. The achieved results indicate that the moisture content of the concrete should be taken into consideration in modulus measurements as well as in Equations estimating Ec,s on the basis of Ed specified by the ultrasonic pulse velocity method. The static modulus of LWACs was lower on average by 11 and 24% in relation to dynamic modulus, respectively when measured in air-dried and water-saturated conditions. The influence of LWAC moisture content on the relationship between specified static and dynamic moduli was not affected by the type of tested lightweight concrete.

Reconstruction of Asphalt Pavements with Crumb Rubber Modified Asphalt Mixture in Cold Region: Material Characterization, Construction, and Performance.

Dry-processed rubberized asphalt mixture has recently attracted a lot of attention as an alternative to conventional asphalt mixtures. Dry-processed rubberized asphalt pavement has improved the overall performance characteristics compared to the conventional asphalt road. The objective of this research is to demonstrate the reconstruction of rubberized asphalt pavement and evaluate the pavement performance of dry-processed rubberized asphalt mixture based on laboratory and field tests. The noise mitigation effect of dry-processed rubberized asphalt pavement was evaluated at the field construction sites. A prediction of pavement distresses and long-term performance was also conducted using mechanistic-empirical pavement design. In terms of experimental evaluation, the dynamic modulus was estimated using materials test system (MTS) equipment, the low-temperature crack resistance was characterized by the fracture energy from the indirect tensile strength test (IDT), and the asphalt aging was assessed with the rolling thin-film oven (RTFO) test and the pressure aging vessel (PAV) test. The rheology properties of asphalt were estimated by a dynamic shear rheometer (DSR). Based on the test results: (1) The dry-processed rubberized asphalt mixture presented better resistance to cracking, as the fracture energy was enhanced by 29-50% compared to that of conventional hot mix asphalt (HMA); and (2) the high-temperature anti-rutting performance of the rubberized pavement increased. The dynamic modulus increased up to 19%. The findings of the noise test showed that at different vehicle speeds, the rubberized asphalt pavement greatly reduced the noise level by 2-3 dB. The pavement M-E (mechanistic-empirical) design-predicted distress illustrated that the rubberized asphalt pavement could reduce the IRI, rutting, and bottom-up fatigue-cracking distress based on a comparison of prediction results. To sum up, the dry-processed rubber-modified asphalt pavement has better pavement performance compared to the conventional asphalt pavement.

Wave Propagation Characteristics and Compaction Status of Subgrade during Vibratory Compaction.

Vibratory compaction status has a significant influence on the construction quality of subgrade engineering. This study carried out field experiments to study the propagation characteristics of the vertical vibration wave in the soil field along the traveling direction of the vibratory roller. The propagation coefficients of the peak acceleration at different positions and compacting rounds are compared in both the time and frequency domains. The compaction status is estimated in the form of dynamic modulus of deformation (Evd) obtained by plate load tests. The experiment results show that the propagation coefficient of peak acceleration is affected by the traveling speed, excitation amplitude, and frequency of the vibratory roller, as well as the compacting rounds. An exponential relationship between the wave amplitudes of the fundamental mode and higher-order modes is revealed. The amplitude of the fundamental wave is maximum at the speed of 3 km/h, whereas the amplitudes of higher-order waves have a maximum of 1.5 km/h. The influences of compaction rounds on the average value of Evd are also investigated to provide a practical reference for engineering construction.

Engineering, Mechanical and Dynamic Properties of Basalt Fiber Reinforced Concrete.

This study investigates the engineering and mechanical properties of basalt fiber-reinforced (FRF) concrete, giving special attention to residual flexural strength and dynamic modal parameters. These properties, which have not been thoroughly investigated elsewhere, are a precursor to structural design applications for dynamic compliant structures (i.e., bridges, offshore platforms, railways, and airport pavement). Accordingly, the standard notched flexural tests have been carried out to assess the basalt fiber-reinforced concrete's residual flexural strength with an additional 0.125%, 0.25%, 0.375%, and 0.5% of volume fraction of basalt fiber. In addition, dynamic modal tests were then conducted to determine the dynamic modulus of elasticity (MOE) and damping of the FRF concrete beams. The results indicate that concrete's toughness and crack resistance performance are significantly improved with added fiber in basalt fiber reinforced concrete, and the optimum fiber content is 0.25%. It also exhibits the highest increment of compressive strength of 4.48% and a dynamic MOE of 13.83%. New insights reveal that although the residual flexural performance gradually improved with the addition of basalt fiber, the damping ratio had an insignificant change.

The Stiffness Behavior of Asphalt Mixtures with Different Compactness under Variable Confinement.

The dynamic modulus is a key property determining the short- and long-term performance of asphalt pavement, and its strong dependence on confining pressure and material density (mixture compactness) has been clearly indicated in the literature. It is always challenging to reproduce three-dimensional in situ stress conditions in the laboratory. To alleviate this difficulty, in this study, a convenient experimental setup was developed, in which the lateral confinement was made present and variable as a concomitant reaction of the surrounding materials to the vertical loading. Three dense-graded mixtures were prepared to a set of four different densities and then subjected to the confined dynamic modulus test. The results indicated a significant dependence of the confined modulus on the three factors of temperature, frequency, and compactness and that the mixture with coarser gradation demonstrated a less sensitivity to these parameters. A mathematical model was developed for the dynamic modulus master curve unifying these factors by means of horizontal shifting due to the time-temperature superposition principle (validated against the variable confinement at different compactness) and the vertical shift factor as a function of reduced frequency and compactness. The adequacy of the model was demonstrated using the experimental data, and its potential application in field pavement compaction was discussed.

Rotator Cuff Tendon Repair after Injury in Hyperlipidemic Swine Decreases Biomechanical Properties.

Rotator cuff injury is the leading cause of shoulder pain. Hyperlipidemia is responsible in depositing lipids in tendons and reduce the healing upon injuries or tears. In this study, we created rotator cuff injury and repair models in swine and studied the changes in biomechanical properties of infraspinatus tendons in hyperlipidemic swine. The infraspinatus tendons from control group, hyperlipidemic injury and repair group of animals were collected and tested ex-vivo. The ultimate tensile strength (UTS) and modulus of elasticity increased in the tendons from the contralateral side on both the injury and repair models and were higher than the injury side. The presence of large number of fibrous tissues in the surgical site of repair and increased water content was observed in addition to the fatty infiltration which would have contributed to the decreased mechanical properties of the injured tendons following repair. Meanwhile the tendons of the contralateral side in both the injury and repair model showed adaptation to chronic load as observed in the modulus and viscoelastic properties. This is a pilot study that warrants detailed investigation in a larger sample size with longer duration following tendon injury and repair to gain better understanding on the effect of hyperlipidemia in the healing of rotator cuff tendon injury.