In situ growth of iron incorporated Ni3S2 nanosheet on nickel foam in mediating electron transfer to peroxymonosulfate for pollutant abatement.

Catalytic oxidation of organic pollutants is a well-known and effective technique for pollutant abatement. Unfortunately, this method is significantly hindered in practical applications by the low efficiency and difficult recovery of the catalysts in a powdery form. Herein, a three-dimensional (3D) framework of Fe-incorporated Ni3S2 nanosheets in-situ grown on Ni foam (Fe-Ni3S2@NF) was fabricated by a facile two-step hydrothermal process and applied to trigger peroxymonosulfate (PMS) oxidation of organic compounds in water. A homogeneous growth environment enabled the uniform and scalable growth of Fe-Ni3S2 nanosheets on the Ni foam. Fe-Ni3S2@NF possessed outstanding activity and durability in activating PMS, as it effectively facilitated electron transfer from organic pollutants to PMS. Fe-Ni3S2@NF initially supplied electrons to PMS, causing the catalyst to undergo oxidation, and subsequently accepted electrons from organic compounds, returning to its initial state. The introduction of Fe into the Ni3S2 lattice enhanced electrical conductivity, promoting mediated electron transfer between PMS and organic compounds. The 3D conductive Ni foam provided an ideal platform for the nucleation and growth of Fe-Ni3S2, accelerating pollutant abatement due to its porous structure and high conductivity. Furthermore, its monolithic nature simplified the catalyst recycling process. A continuous flow packed-bed reactor by encapsulating Fe-Ni3S2@NF catalyst achieved complete pollutant abatement with continuous operation for 240 h, highlighting its immense potential for practical environmental remediation. This study presents a facile synthesis method for creating a novel type of monolithic catalyst with high activity and durability for decontamination through Fenton-like processes.

Co-doped cryptomelane-type manganese oxide in situ grown on a nickel foam substrate for high humidity ozone decomposition.

Monolithic catalysts with excellent O3 catalytic decomposition performance were prepared by in situ loading of Co-doped KMn8O16 on the surface of nickel foam. The triple-layer structure with Co-doped KMn8O16/Ni6MnO8/Ni foam was grown spontaneously on the surface of nickel foam by tuning the molar ratio of KMnO4 to Co(NO3)2·6H2O precursors. Importantly, the formed Ni6MnO8 structure between KMn8O16 and nickel foam during in situ synthesis process effectively protected nickel foam from further etching, which significantly enhanced the reaction stability of catalyst. The optimum amount of Co doping in KMn8O16 was available when the molar ratio of Mn to Co species in the precursor solution was 2:1. And the Mn2Co1 catalyst had abundant oxygen vacancies and excellent hydrophobicity, thus creating outstanding O3 decomposition activity. The O3 conversion under dry conditions and relative humidity of 65%, 90% over a period of 5 hr was 100%, 94% and 80% with the space velocity of 28,000 hr-1, respectively. The in situ constructed Co-doped KMn8O16/Ni foam catalyst showed the advantages of low price and gradual applicability of the preparation process, which provided an opportunity for the design of monolithic catalyst for O3 catalytic decomposition.

Chrysin downregulates the expression of ADAMTS-4 in foam cells.

BACKGROUND: Chrysin, a polyphenolic compound, possesses antioxidant and anti-inflammatory properties. In this study, we investigated the effect of chrysin on the expression of A disintegrin and metalloproteinase with thrombospondin motifs-4 (ADAMTS-4), a protease enzyme involved in degrading extracellular matrix associated with atherosclerosis. METHODS AND RESULTS: We have studied the cell viability by MTT assay and foam cell formation by oil red O staining. The mRNA and protein expression of ADAMTS-4 was studied using quantitative polymerase chain reaction (qPCR) and Western blotting, respectively. Our study showed that chrysin significantly downregulates the expression of ADAMTS-4 in foam cells. CONCLUSION: Chrysin's ability to downregulate the expression of ADAMTS-4, a protease involved in degrading the extracellular matrix, bestows upon it a new therapeutic potential for managing atherosclerosis.

Valorization of polyurethane foam waste through the decoration with nano-polyaniline for dye decontamination from polluted water.

Two polyurethane polyaniline nanocomposites have been synthesized using two in situ polymerization routes of dried and wet bases to valorize the polyurethane waste. The physical and chemical properties of polyurethane-based nanocomposites were compared using SEM, XRD, FTIR, and Zeta potential. SEM images showed that the average particle size of the dried-based composite was 56 nm, while the wet-based composite had an average size of 75 nm. The separation efficiency for methylene blue (MB) and Congo red (CR) dyes was evaluated against free polyurethane foam waste. It was evident that pure polyurethane (PPU) achieved only 4.79% and 16.71% removal for MB and CR, respectively. These dye decontamination efficiencies were enhanced after nano polyaniline decoration of polyurethane foam either through dried base polymerization (DPUP) or wet base polymerization (WPUP). WPUP composite records 11.23% and 85.99% for MB and CR removal, respectively, improved to 26.69% and 90.07% removal using DPUP composite for the respective dyes. The adsorption kinetics, isotherms, and thermodynamics were investigated. The experimental results revealed the pseudo-second-order kinetic model as the most accurately described kinetics model for both CR and MB adsorption. The Langmuir model provided the best fit for the data, with maximum adsorption capacities of 110.98 mg/g for CR and 26.86 mg/g for MB, with corresponding R-squared values of 0.9974 and 0.9608, respectively. Regeneration and reusability studies of PPU, WPUP, and DPUP showed effective reusability, with DPUP displaying the highest adsorption capacity. These results aid in creating eco-friendly and cost-efficient adsorbents for dye removal in environmental sanitation.

Design and optimization of pore structure in three-dimensional micro-nano hierarchical SnOx supercapacitor electrodes for enhanced ion diffusion.

This paper introduced a novel continuous electrochemical synthesis strategy to address the challenges of slow ion/electron transport rates and low electrode reaction efficiency in Sn-based electrode materials. This approach leveraged the induction and confinement of bubble templates to assist atoms deposition, generating micron-sized tin skeletons. Subsequently, these skeletons were transformed into a secondary nanoporous structure through dissolution-deposition etching effects. From liquid-phase ions to metal skeletons to porous oxides, the sequential material transformations realized the innovative design of three-dimensional (3D) hierarchical structures. This strategy ingeniously exploited the diffusion advantages of the electrolyte in the micro-nano hierarchical structure to achieve the diffusion enhancement of ions, thus solving the "dead surface" problem in the energy storage process. This study revealed the thermodynamic and kinetic feasibility of the constructed 3D micro-nano hierarchical structure through electrochemical evaluations and theoretical calculations, and elucidated the constitutive relationship in which the electrochemical performance of the electrode materials was enhanced with decreasing pore size. In addition, design optimization of pore structures and modelling exploration of pore size limit values were conducted based on density functional theory (DFT) simulations. These simulations demonstrated the advantages of hierarchical structures with controllable pore sizes in facilitating electrolyte ion diffusion, predicting an optimal pore size of 55 µm for 3D hierarchical porous SnOx electrodes. The integration of this innovative structural design with simulation insights offered significant implications for enhancing the sluggish electrode reaction kinetics of metal oxide electrode materials, advancing the controllable fabrication of high-performance energy storage devices.

Three-dimensional gel network structure of agarose interlayer dispersed Pd nanoparticles in copper foam electrode for electrocatalytic degradation of doxycycline hydrochloride.

In this study, we successfully prepared palladium/agarose/copper foam (Pd/AG/CF) composite electrodes by utilizing the three-dimensional network structure agarose (AG), a green material derived from biomass, and homogeneously immobilizing palladium (Pd) atoms on a copper foam (CF) substrate through a facile route. The electrode showed excellent performance in the electrocatalytic degradation of doxycycline (DOX), with a high DOX degradation rate of 92.19 % in 60 min. In-depth studies revealed that palladium can form metal-metal interactions with the CF substrates, which enhances the electron transfer on the catalyst surface. In addition, the introduction of agarose effectively prevented the agglomeration of palladium nanoparticles. In addition, the hydroxyl functional groups in the molecular structure of agarose facilitate interactions between water molecules and the electrode interface through the formation of hydrogen bonds, thereby further enhancing the efficiency of the electrocatalytic reaction. In addition to good stability and reusability. Microbial toxicity test results show that the degraded wastewater has minimal impact on the environment. Also, possible degradation pathways of DOX were explored in this study. Finally, a novel continuous flow reactor was designed, featuring a unique design that ensures full contact between wastewater and the composite electrodes, thereby achieving continuous and efficient treatment of antibiotic wastewater.

In Vitro Modulation of Human Foam Cell Formation and Adhesion Molecules Expression by Ginger Extracts Points to Potential Cardiovascular Preventive Agents.

Recent findings from the World Heart Federation (WHF) reported a significant increase in cardiovascular disease (CVD)-related deaths, highlighting the urgent need for effective prevention strategies. Atherosclerosis, a key precursor to CVD, involves the accumulation of low-density lipoprotein (LDL) and its oxidation within the endothelium, leading to inflammation and foam cell formation. Ginger extracts, known for their antioxidative and anti-inflammatory properties, show promise in preventing CVD initiation by inhibiting LDL oxidation and reducing foam cell formation. Our results revealed that the active fractions in ginger extracts had antioxidative effects, particularly fractions D and E. Further research is needed to identify the active compounds in these fractions and understand their mechanisms of action. In this context, microfluidic models could offer insights into the effects of ginger on monocyte recruitment in a more physiologically relevant context. Overall, ginger extracts represent a potential novel treatment for preventing CVD initiation, but additional studies are necessary to identify the active molecules in these fractions.

Study on the Control of Steam Front Mobility in High-Temperature and High-Salinity Conditions Using Polymer-Enhanced Foam.

This study investigated the enhancing effects of the temperature-resistant polymer Poly(ethylene-co-N-methylbutenoyl carboxylate-co-styrenesulfonate-co-pyrrolidone) (hereinafter referred to as Z364) on the performance of cocamidopropyl hydroxy sulfobetaine (CHSB) foam under high-temperature and high-salinity conditions. The potential of this enhanced foam system for mobility control during heavy oil thermal recovery processes was also evaluated. Through a series of experiments, including foam stability tests, surface tension measurements, rheological assessments, and parallel core flooding experiments, we systematically analyzed the interaction between the Z364 polymer and CHSB surfactant on foam performance. The results indicated that the addition of Z364 significantly improved the strength, thermal resistance, and salt tolerance of CHSB foam. Furthermore, the adsorption of CHSB on the polymer chains enhanced the salt resistance of the polymer itself, particularly demonstrating stronger blocking effects in high-permeability cores. The experimental findings showed that Z364 increased the viscosity of the liquid film, slowed down liquid drainage, and reduced gas diffusion, effectively extending the half-life of CHSB foam and improving its stability under high-temperature conditions. Additionally, in parallel core flooding experiments, the polymer-enhanced foam exhibited significant flow diversion effects in both high-permeability and low-permeability cores, effectively directing more fluid into low-permeability channels and improving fluid distribution in heterogeneous reservoirs. Overall, Z364 polymer-enhanced CHSB foam demonstrated superior mobility control during heavy oil thermal recovery, offering new technical insights for improving the development efficiency of high-temperature, high-salinity reservoirs.

A New Method for the Dynamics Analysis of Super-Elastic-Plastic Foams under Inhomogeneous Loading and Unloading Conditions.

In this research, a new computational method was proposed for describing the mechanical behavior of super-elastic-plastic foams under inhomogeneous compressive impacts. The method regarded the foam material as composed of two typical mechanical properties superimposed multiple times: one was the hyper-elastic layer, and the other was the elastoplastic layer. The hyper-elastic layer and the elastoplastic layer were interwoven and overlapped, divided into double-layer, four-layer, and six-layer configurations to characterize the foam material. After the equivalent layering of the foam, by comparing the results of the four-layer and six-layer divisions, it was found that when the layering reached four layers, the foam performance curve had already converged. The study utilized the HYPERFOAM model and Mullins effect in the ABAQUS software to establish the constitutive relationship of the hyper-elastic layer. It adopted the Crushable foam model to develop the constitutive relationship of the elastoplastic layer. Under uniaxial compression conditions, quasi-static and intermediate strain rate compression tests were performed on polyethylene (PE) foam materials with three different densities. Based on the experimental results, the parameter values of the hyper-elastic-plastic foam model in the ABAQUS code were determined. By comparing the computational results and the experimental results, the established finite element (FE) model was validated using the mechanical behavior of indentation and compression tests. The results showed that this method could effectively describe the complex mechanical behavior and residual deformation of hyper-elastic-plastic foam packaging materials under non-uniform compression, and the experimental and simulation results agreed well, proving the reliability of this method.

Optimized Eco-Friendly Foam Materials: A Study on the Effects of Sodium Alginate, Cellulose, and Activated Carbon.

This study focuses on optimizing the physical and mechanical properties of foam materials produced with the addition of sodium alginate as the matrix, and cellulose and activated carbon as fillers. Foam materials, valued for their lightweight and insulation properties, are typically produced from synthetic polymers that pose environmental risks. To mitigate these concerns, this study investigates the potential of natural, biodegradable polymers. Various foam formulations were tested to evaluate their density, compression modulus, and thermal conductivity. The results indicated that an increase in activated carbon content enhanced thermal stability, as indicated by higher Ti% and Tmax% values. Additionally, a higher concentration of sodium alginate and activated carbon resulted in higher foam density and compressive modulus, while cellulose exhibited a more intricate role in the material's behavior. In the optimal formula, where the sum of the component percentages totals 7.6%, the percentages (e.g., 0.5% sodium alginate, 5% cellulose, and 2.1% activated carbon) are calculated based on the weight/volume (w/v) ratio of each component in the water used to prepare the foam mixture. These results indicate that natural and biodegradable polymers can be used to develop high-performance, eco-friendly foam materials.

Study on the Preparation and Performance of Lightweight Wallboards from MSWIBA Foam Concrete.

To reduce land use and avoid further pollution, incineration for power generation has become the main method for municipal solid waste treatment. This research focused on the potential for transforming Municipal Solid Waste Incineration Bottom Ash (MSWIBA) into a finely ground powder. The impact of the powder's fineness and the amount of water used on its effectiveness was analyzed using a method called grey theory. MSWIBA was used as a partial substitute for cement in making MSWIBA foam concrete and lightweight wall panels. By modifying the fineness and water utilization of the recycled micro-powder, its maximum activity index can be increased to 90.1. This study determined the influence of factors including apparent dry density, water-cement ratio, foaming agent dilution ratio, and admixture dosage on the strength of the recycled foam concrete, and established the optimal mix ratio. This study employed a combination of physical experiments and numerical simulations to elucidate the impact of panel material, core layer thickness, and layer sequence on sound insulation performance. The simulation results were in close agreement with the experimental findings.

Integrated multi-omic high-throughput strategies across-species identified potential key diagnostic, prognostic, and therapeutic targets for atherosclerosis under high glucose conditions.

Diabetes is a well-known risk factor for atherosclerosis (AS), but the underlying molecular mechanism remains unknown. The dysregulated immune response is an important reason. High glucose is proven to induce foam cell formation under lipidemia situations in clinical patients. Exploring the potential regulatory programs of accelerated foam cell formation stimulated by high glucose is meaningful. Macrophage-derived foam cells were induced in vitro, and high-throughput sequencing was performed. Coexpression gene modules were constructed using weighted gene co-expression network analysis (WGCNA). Highly related modules were identified. Hub genes were identified by multiple integrative strategies. The potential roles of selected genes were further validated in bulk-RNA and scRNA datasets of human plaques. By transfection of the siRNA, the role of the screened gene during foam cell formation was further explored. Two modules were found to be both positively related to high glucose and ox-LDL. Further enrichment analyses confirmed the association between the brown module and AS. The high correlation between the brown module and macrophages was identified and 4 hub genes (Aldoa, Creg1, Lgmn, and Pkm) were screened. Further validation in external bulk-RNA and scRNA revealed the potential diagnostic and therapeutic value of selected genes. In addition, the survival analysis confirmed the prognostic value of Aldoa while knocking down Aldoa expression alleviated the foam cell formation in vitro. We systematically investigated the synergetic effects of high glucose and ox-LDL during macrophage-derived foam cell formation and identified that ALDOA might be an important diagnostic, prognostic, and therapeutic target in these patients.

Multi-omics analysis of the lipid-regulating effects of metformin in a glucose concentration-dependent manner in macrophage-derived foam cells.

Metformin has a long history of clinical application and has been shown to have outstanding ability in lowering glucose. Recent advances have further revealed its broad modulatory ability beyond glucose-lowering, expanding the scope of metformin applications. Metformin has now been applied as a viable lipid-lowering strategy in non-hyperglycemic obese patients. However, the benefits and underlying pharmacological mechanisms of metformin administration in non-hyperglycemic populations remain to be explained. Our study aimed to systematically investigate the differences in the lipid-lowering function and pharmacological mechanisms of metformin in high- and low-sugar conditions to facilitate the development of individualized metformin use regimens for different clinical patients. We constructed macrophage-derived foam cell models in vitro for subsequent analysis. ORO results showed that metformin significantly reduced lipid accumulation in macrophages in both high and low glucose environments, but the lipid decline was higher in the high glucose environment. By mutual validation and joint analysis of transcriptomics and metabolomics, significant differences in metformin transcriptional and metabolic patterns existed among high and normal glucose environments. The significant alterations of genes such as DGKA, LPL, DGAT2 and lipid metabolites such as LysPA and LysPC partially explained the glucose-dependent pharmacological function of metformin. In conclusion, our study confirmed that the lipid-lowering effect of metformin depends on the extracellular glucose concentration, and systematically studied the molecular mechanism of metformin in different glycemic environments, which provides a certain reference value for the subsequent in-depth study and clinical application.

Solar-Driven Harvesting of Freshwater and Electricity Based on Three-Dimensional Hierarchical Cu2-xO@Cu Foam.

The integration of solar steam generation and the hydrovoltaic effect is a promising strategy for simultaneously solving water scarcity and energy crises. However, it is still a challenge to attain a high water evaporation rate and a strong output of electricity in a single device. Here, we report a three-dimensional (3D) hierarchical Cu2-xO@Cu foam for solar-driven harvesting of freshwater and electricity efficiently. The 3D Cu2-xO@Cu foam synthesized by chemical etching shows a rough surface and porous structure, making it have a hydrophilic surface, high light absorption performance, and excellent photothermal effect. For deionized water, the evaporation rate is as high as 3.03 kg m-2 h-1; meanwhile, the output voltage is 0.37 V under 1 solar irradiation. For real seawater, the evaporation rate decreases to about 2.48 kg m-2 h-1, the output voltage increases to 0.41 V, and the maximum output power density is 9.47 µW cm-2. Both the water evaporation and power generation performance are very competitive. Outdoor experiments demonstrate that the 3D hierarchical Cu2-xO@Cu foam can desalinate seawater, while generating electricity continuously.

Foam Stabilization Process for Nano-Al2O3 and Its Effect on Mechanical Properties of Foamed Concrete.

Foamed concrete is increasingly utilized in engineering due to its light weight, excellent thermal insulation, fire resistance, etc. However, its low strength has always been the most crucial factor limiting its large-scale application. This study introduced an innovative method to enhance the strength of foamed concrete by using nano-Al2O3 (NA) as a foam stabilizer. NA was introduced into a foaming agent containing sodium dodecyl sulfate (SDS) and hydroxypropyl methylcellulose (HPMC) to prepare a highly stable foam. This approach significantly improved the foam stability and the strength of foamed concrete. Its drainage volume, settlement distance, microstructure, and stabilizing action were investigated, along with the strength, microstructure, and hydration products of foamed concrete. The presence of NA effectively reduced the drainage volume and settlement distance of the foam. NA is distributed at the gas-liquid interface and within the liquid film to play a hindering role, increasing the thickness of the liquid film, delaying the liquid discharge rate from the liquid film, and hindering bubble aggregation, thereby enhancing foam stability. Additionally, due to the stabilizing effect of NA on the foam, the precast foam forms a fine and uniform pore structure in the hardened foamed concrete. At 28 d, the compressive strength of FC0 (0% NAs in foam) is 2.18 MPa, while that of FC3 (0.18% NAs in foam) is 3.90 MPa, increased by 79%. The reason for this is that NA promotes the formation of AFt, and its secondary hydration leads to the continuous consumption of Ca(OH)2, resulting in a more complete hydration reaction. This study presents a novel method for significantly improving the performance of foamed concrete by incorporating NA.

The senescent marker p16INK4a enhances macrophage foam cells formation.

BACKGROUND: The senescence marker p16INK4a, which constitutes part of the genome 9p21.3 cardiovascular disease (CVD) risk allele, is believed to play a role in foam cells formation. This study aims to unravel the role of p16INK4a in mediating macrophage foam cells formation, cellular senescence, and autophagy lysosomal functions. METHODS: The mammalian expression plasmid pCMV-p16INK4a was used to induce p16INK4a overexpression in THP-1 macrophages. Next, wild-type and p16INK4a-overexpressed macrophages were incubated with oxidized LDL to induce foam cells formation. Lipids accumulation was evaluated using Oil-red-O staining and cholesterol efflux assay, as well as expression of scavenger receptors CD36 and LOX-1. Cellular senescence in macrophage foam cells were determined through analysis of senescence-associated ß-galactosidase activity and other SASP factors expression. Meanwhile, autophagy induction was assessed through detection of autophagosome formation and LC3B/p62 markers expression. RESULTS: The findings showed that p16INK4a enhanced foam cells formation with increased scavenger receptors CD36 and LOX-1 expression and reduced cholesterol efflux in THP-1 macrophages. Besides, ß-galactosidase activity was enhanced, and SASP factors such as IL-1α, TNF-α, and MMP9 were up-regulated. In addition, p16INK4a is also shown to induce autophagy, as well as increasing autophagy markers LC3B and p62 expression. CONCLUSIONS: This study provides insights on p16INK4a in mediating macrophages foam cells formation, cellular senescence, and foam cells formation.

Interleukin-34-orchestrated tumor-associated macrophage reprogramming is required for tumor immune escape driven by p53 inactivation.

As the most frequent genetic alteration in cancer, more than half of human cancers have p53 mutations that cause transcriptional inactivation. However, how p53 modulates the immune landscape to create a niche for immune escape remains elusive. We found that cancer stem cells (CSCs) established an interleukin-34 (IL-34)-orchestrated niche to promote tumorigenesis in p53-inactivated liver cancer. Mechanistically, we discovered that Il34 is a gene transcriptionally repressed by p53, and p53 loss resulted in IL-34 secretion by CSCs. IL-34 induced CD36-mediated elevations in fatty acid oxidative metabolism to drive M2-like polarization of foam-like tumor-associated macrophages (TAMs). These IL-34-orchestrated TAMs suppressed CD8+ T cell-mediated antitumor immunity to promote immune escape. Blockade of the IL-34-CD36 axis elicited antitumor immunity and synergized with anti-PD-1 immunotherapy, leading to a complete response. Our findings reveal the underlying mechanism of p53 modulation of the tumor immune microenvironment and provide a potential target for immunotherapy of cancer with p53 inactivation.

First registry of patients treated with foam sclerotherapy using a new automated microfoam preparation device (2021-2022).

Objectives: To present results for the use of an automated microfoam preparation system (AMPS) in the treatment of varicose veins in a real-world setting.Method: We performed a descriptive study based on a prospective database of patients treated with foam sclerotherapy between February 2021 and December 2022. Polidocanol foam was prepared using a capsule containing sterile air or a low-nitrogen mix. We recorded volume per session, percentage of sclerosing drug, number of sessions, release of thrombus entrapment, complications, and adverse events. A univariate descriptive analysis was performed using Stata V.16.Results: Over a 23-month period, 185 patients (84.9% women, 15.1% men) underwent 685 sessions. Median age was 51.6 years (range, 16-79 years). Thread veins were the condition treated in 68.9% of sessions, tributaries in 7.2%, and truncal veins in 22.6%. The average volume per session was as follows: thread veins, 8 mL; great saphenous vein (GSV), 6.9 mL; and small saphenous vein (SSV), 4.3 mL. The average drug concentration was as follows: thread veins, 0.18%; GSV, 1.49%; and SSV, 1.63%. The average number of sessions was 3.4 for thread veins, 2 for tributaries, 2.7 for the GSV, and 2.9 for the SSV. The occlusion rate at 15 months was 93.2% (41/43) for the great saphenous vein and 86% (13/15) for the small saphenous vein. We recorded a total of 21 complications (3.1% of sessions), 14 of which were minor complications (2% sessions), and 7 moderate adverse events (1% of sessions).Conclusions: This new device is highly versatile and can be used for preparing foam at all concentrations. It contributes to a high rate of occlusion in saphenous trunks, with a minimal number of sessions required for thread veins indicating that the system is a favorable option in the treatment of venous diseases. Additionally, the low frequency of residual pigmentation may be attributed to the system's ability to tailor the foam concentration to the individual case, thus supporting optimal outcomes.

Soft material drilling: A thermo-mechanical analysis of polyurethane foam for biomimetic bone scaffolds and optimization of process parameters using Taguchi method.

Drilling is a widely employed technique in machining processes, crucial for efficient material removal. However, when applied to living tissues, its invasiveness must be carefully considered. This study investigates drilling processes on polyurethane foam blocks mimicking human bone mechanical properties. Various drill bit types (118° twist, 135° twist, spherical, and conical), drilling speeds (1000-1600 rpm), and feed rates (20-80 mm/min) were examined to assess temperature elevation during drilling. The Taguchi method facilitated systematic experiment design and optimization. Signal-to-noise (S/N) ratio and analysis of variance (ANOVA) identified significant drilling parameters affecting temperature rise. Validation was conducted through confirmation testing. Results indicate that standard twist drill bits with smaller point angles, lower drilling speeds, and higher feed rates effectively minimize temperature elevation during drilling.

Liquefaction optimization of grape pulp using response surface methodology for biopolyol production and bio-based polyurethane foam synthesis.

Both environmental and economic disadvantages of using petroleum-based products have been forcing researchers to work on environmentally friendly, sustainable, and economical alternatives. The purpose of this study is to optimize the solvothermal liquefaction process of grape pomace using response surface methodology coupled with a central composite design. After investigating the physicochemical properties of the liquified products (biopolyol) in detail, a bio-based rigid polyurethane foam (RPUF) was synthesized and characterized. The hydroxyl and acid numbers and viscosity values of all the biopolyols were analyzed. According to variance analysis results (%95 confidence range), both the reaction temperature and catalyst loading were determined as significant parameters on the liquefaction yield (LY). The model was validated experimentally in the following reaction conditions: 4.25% catalyst loading, 50 min reaction time, and 165 °C reaction temperature, which yields an LY of 81.3%. The biopolyols produced by the validation experiment display similar characteristics (hydroxyl number: 470.5 mg KOH/g; acid number: 2.31 mg KOH/g; viscosity: 1785 cP at 25 °C) to those of commercial polyols widely preferred in the production of polyurethane foam. The physicochemical properties of bio-based foam obtained from the biopolyol were determined and the thermal conductivity, closed-cell content, apparent density, and compressive strength values of bio-based RPUF were 31.3 mW/m·K, 71.1%, 33.4 kg/m3, and 105.3 kPa, respectively.