Mechanism for Adsorption, Dissociation, and Diffusion of Hydrogen in High-Entropy Alloy AlCrTiNiV: First-Principles Calculation.

To investigate hydrogen behaviors in the high-entropy alloy AlCrTiNiV, density functional theory and transition state theory were used to explore the molecular H2 absorption and dissociation and the atomic H adsorption, diffusion, and penetration progress. The H2 molecule, where the H-H band is parallel to the surface layer, is more inclined to absorb on the top site of the Ti atom site of first atomic layer on the AlCrTiNiV surface, then diffuse into the hollow sites, through the bridge site, after dissociating into two H atoms. Atomic H is more likely to be absorbed on the hollow site. The absorption capacity for atomic H on the surface tends to decline with the increase in H coverage. By calculating the energy barriers of atomic H penetration in AlCrTiNiV, it was indicated that lattice distortion may be one important factor that impacts the permeation rate of hydrogen. Our theory research suggests that high-entropy alloys have potential for use as a hydrogen resistant coating material.

High-Temperature Oxidation and Phase Stability of AlCrCoFeNi High Entropy Alloy: Insights from In Situ HT-XRD and Thermodynamic Calculations.

The high-temperature oxidation behaviour and phase stability of equi-atomic high entropy AlCrCoFeNi alloy (HEA) were studied using in situ high-temperature X-ray diffraction (HTXRD) combined with ThermoCalc thermodynamic calculation. HTXRD analyses reveal the formation of B2, BCC, Sigma and FCC, phases at different temperatures, with significant phase transitions observed at intermediate temperatures from 600 °C-100 °C. ThermoCalc predicted phase diagram closely matched with in situ HTXRD findings highlighting minor differences in phase transformation temperature. ThermoCalc predictions of oxides provide insights into the formation of stable oxide phases, predominantly spinel-type oxides, at high p(O2), while a lower volume of halite was predicted, and minor increase observed with increasing temperature. The oxidation behaviour was strongly dependent on the environment, with the vacuum condition favouring the formation of a thin, Al2O3 protective layer, while in atmospheric conditions a thick, double-layered oxide scale of Al2O3 and Cr2O3 formed. The formation of oxide scale was determined by selective oxidation of Al and Cr, as further confirmed by EDX analysis. The formation of thick oxide in air environment resulted in a thick layer of Al-depleted FFC phase. This comprehensive study explains the high-temperature phase stability and time-temperature-dependent oxidation mechanisms of AlCrCoFeNi HEA. The interplay between surface phase transformation beneath oxide scale and oxides is also detailed herein, contributing to further development and optimisation of HEA for high temperature applications.

Ultra-Small High-Entropy Alloy as Multi-Functional Catalyst for Ammonia Based Fuel Cells.

Ammonia fuel cells using carbon-neutral ammonia as fuel are regarded as a fast, furious, and flexible next-generation carbon-free energy conversion technology, but it is limited by the kinetically sluggish ammonia oxidation reaction (AOR), oxygen reduction reaction (ORR), and hydrogen evolution reaction (HER). Platinum can efficiently drive these three types of reactions, but its scale-up application is limited by its susceptibility to poisoning and high cost. In order to reduce the cost and alleviate poisoning, incorporating Pt with various metals proves to be an efficient and feasible strategy. Herein, PtFeCoNiIr/C trifunctional high-entropy alloy (HEA) catalysts are prepared with uniform mixing and ultra-small size of 2 ± 0.5 nm by Joule heating method. PtFeCoNiIr/C exhibits efficient performance in AOR (Jpeak = 139.8 A g-1 PGM), ORR (E1/2 = 0.87 V), and HER (E10 = 20.3 mV), outperforming the benchmark Pt/C, and no loss in HER performance at 100 mA cm-2 for 200 h. The almost unchanged E1/2 in the anti-poisoning test indicates its promising application in real fuel cells powered by ammonia. This work opens up a new path for the development of multi-functional electrocatalysts and also makes a big leap toward the exploration of cost-effective device configurations for novel fuel cells.

Disparities in access to breast, colorectal, and cervical cancer screening programmes have intensified during the pandemic period. Findings of a health equity audit conducted by the Pavia Healthcare Protection Agency (Lombardy Region, Northern Italy)

OBJECTIVES: to evaluate the disparities in access to cancer screening programmes in the Province of Pavia (Lombardy Region, Northern Italy), along with identifying the factors influencing these disparities; to assess the impact of the pandemic emergency on invitation and screening coverage in the three organized screening programmes, which are provided free of charge to the target population. DESIGN: observational retrospective study covering both the pre-pandemic and the pandemic periods. SETTING AND PARTICIPANTS: for breast cancer screening, the eligible population comprises women aged 45 to 74; colorectal cancer screening is offered to men and women aged 50 to 74; cervical cancer screening is tailored based on women age. The management of all three screening programmes is overseen by the Health Protection Agency of Pavia, which proactively invites the eligible population through invitation letters. MAIN OUTCOMES MEASURES: for each screening programme, the examination coverage (the number of screened individuals out of the total eligible population) was analysed considering its influencing factors, with a specific emphasis on equity-related factors such as demographics (sex, age), geographic factors (country and continent of birth, residential district), comorbidities. RESULTS: the SARS-CoV-2 pandemic has led to a reorganization of healthcare services and to a reduction of the offer, resulting in an overall reduction in test coverage for all three programmes (-16.3% for breast and colorectal cancer screening, -8.5% for cervical cancer screening). The disparities in coverage among various population groups, reflecting inequalities in access, further escalated from the pre-pandemic to the pandemic period. Noteworthy, equity-related predictors of reduced screening access were non-Italian nationality and residency in rural or mountainous districts. CONCLUSIONS: during periods of healthcare system strain, such as the pandemic, disparities in access can become more pronounced. It is crucial to implement measures for enhancing access to screening in a more equitable manner.

Plane-Stress Deformation Behavior of CoCrFeMnNi High-Entropy Alloy Sheet under Low Temperatures.

High-entropy alloys are promising candidates expected to be applied in transportation equipment serving in extreme environments due to their excellent properties. CoCrFeMnNi high-entropy alloy is a typical representative of them, and its low temperature performance is excellent. In this study, to evaluate the feasibility of forming HEA shells, the deformation behavior of CoCrFeMnNi under a plane-stress state at lower temperatures was thoroughly studied. Firstly, a thin-walled HEA tube was fabricated using hot extrusion and further formed into a thin shell for uniaxial tensile and biaxial bulging tests. Subsequently, uniaxial tensile tests at cryogenic temperatures were conducted. Both the strength and the ductility improves as the temperature decreases from -160 °C to -196 °C. Then, a systematic low-temperature bulging test was performed using isothermal dome tests and the thickness uniformity analysis of the bulged specimens was carried out. In addition, grain microstructural observation using EBSD was characterized analyze the possible deformation mechanism at the cryogenic temperature under the biaxial stress state. This study, for the first time, investigated the biaxial deformation behavior of HEA. Considering the plane-stress state deformation is the dominant type in the thin-walled shell deformation, this study enables us to provide direct guidance for various sheet-forming processes of HEAs.

The Effect of Laser Remelting during SLM on Microstructure and Mechanical Properties of CoCrFeNiNb0.25.

A sub-eutectic high-entropy alloy composed of CoCrFeNiNb0.25 was prepared using a combination of mechanical powder mixing and selective laser melting (SLM). The mechanical properties of the alloy were enhanced by employing an interlayer laser remelting process. This study demonstrates the feasibility of using mechanical mixing and SLM to form an CoCrFeNiNb0.25 alloy. The interlayer laser remelting process can effectively promote the melting of Nb particles introduced by mechanical mixing, release the stresses near the unfused Nb particles, and reduce their degradation of the specimen properties. The results indicate that the CoCrFeNiNb0.25 alloy, prepared using the interlayer laser remelting process, had an average microhardness of 376 HV, a tensile strength of 974 MPa, and an elongation at break of 10.51%. This process offers a viable approach for rapidly adjusting the composition of high-entropy alloys for SLM forming.

Microstructure, Mechanical Properties and Wear Behaviors of Ultrafine-Grain WC-Based Cermets with Different Binder Phases Fabricated by Spark Plasma Sintering.

In this work, to explore potential substitutions for the Co binder phase, ultrafine-grain WC-based cermets with various binder phases of Co, Ni and AlCoCrNiFeCu HEA were prepared using the SPS method. Based on SPS, WC-based cermets were fabricated at higher speed, showing fine carbide particles less than 410 µm. The microstructure, mechanical properties and wear properties were systematically evaluated. By comparison, the grain size of WC was the lowest for WC-10Co, while WC-10 HEA cermet held the coarsest WC particles. The hardness and fracture toughness of WC-10 HEA were the best among all three samples, with values of 93.2 HRA and 11.3 MP·m1/2. However, the bending strength of WC-10HEA was about 56.1% lower than that of WC-10Co, with a value of 1349.6 MPa. The reduction in bending strength is attributed to the lower density, formation of a newly Cr-Al rich phase and coarser WC grains. In dry sliding wear conditions, WC-10 HEA showed the lowest wear rate (0.98 × 10-6 mm3/(N·m)) and coefficient of friction (0.19), indicating the best wear resistance performance. This reveals that WC-based cermet with a HEA binder phase has superior wear performance due to the higher hardness and good self-lubricating effect of the wear products.

Improving Mechanical Properties of Fe-Mn-Co-Cr High-Entropy Alloy via Annealing after Cold Rolling.

The as-cast (Fe50Mn30Co10Cr10)97C2Mo1 HEA (high entropy alloy) was prepared and cold-rolled at 70%. Subsequently, annealing heat treatment at different temperatures (900 °C, 950 °C, 1000 °C) was carried out. The microstructure evolution and mechanical properties of the HEA were systematically investigated. The results showed that the HEA annealed at 900 °C and 950 °C exhibited uneven grain size and rich σ precipitation phase at grain boundaries. The grains began to grow and complete recrystallization, and no σ phases were observed in HEA annealed at 1000 °C, which resulted in a higher tensile strength of ~885 MPa and elongation of ~68% compared with other annealed HEAs. The higher volume fraction of annealing twins with 60°<111> orientation was produced in HEA annealed at 1000 °C, which enhanced the tensile strength and plasticity via the Twinning-induced plasticity (TWIP) mechanism.

Protective Effect of Hop Ethyl Acetate Extract on Corticosterone-Induced PC12 and Improvement of Depression-like Behavior in Mice.

Depression is a common mental disorder. In recent years, more and more attention has been paid to depression and its etiology and pathogenesis. This review aims to explore the neuroprotective and antidepressant effects of hop components. By establishing an in vitro cell damage model using PC12 cells induced by corticosterone (CORT) and an in vivo depression model through the intracranial injection of lipopolysaccharide (LPS) in mice, hop ethyl acetate extract (HEA) was used to study the protective effect and mechanism of HEA on neuronal cells in vitro and the antidepression effect and mechanism in vivo. The results showed that HEA increased the survival and decreased the rate of lactate dehydrogenase (LDH) release, apoptosis, and the ROS and NO content of CORT-induced PC12 cells. HEA alleviated depressive-like behavior, neuroinflammation, reduction of norepinephrine, and dendritic spines induced by intracerebroventricular injection of LPS in mice and increases the expression levels of BDNF, SNAP 25, and TrkB proteins without any significant side effects or toxicity. Hops demonstrated significant comprehensive utilization value, and this work provided an experimental basis for the role of hops in the treatment of depression and provided a basis for the development of HEA for antidepressant drugs or dietary therapy products.

Structural Parameters and Behavior in Simulated Body Fluid of High Entropy Alloy Thin Films.

The structure, composition and corrosion properties of thin films synthesized using the Pulsed Laser Deposition (PLD) technique starting from a three high entropy alloy (HEA) AlCoCrFeNix produced by vacuum arc remelting (VAR) method were investigated. The depositions were performed at room temperature on Si and mirror-like polished Ti substrates either under residual vacuum (low 10-7 mbar, films denoted HEA2, HEA6, and HEA10, which were grown from targets with Ni concentration molar ratio, x, equal to 0.4, 1.2, and 2.0, respectively) or under N2 (10-4 mbar, films denoted HEN2, HEN6, and HEN10 for the same Ni concentration molar ratios). The deposited films' structures, investigated using Grazing Incidence X-ray Diffraction, showed the presence of face-centered cubic and body-centered cubic phases, while their surface morphology, investigated using scanning electron microscopy, exhibited a smooth surface with micrometer size droplets. The mass density and thickness were obtained from simulations of acquired X-ray reflectivity curves. The films' elemental composition, estimated using the energy dispersion X-ray spectroscopy, was quite close to that of the targets used. X-ray Photoelectron Spectroscopy investigation showed that films deposited under a N2 atmosphere contained several percentages of N atoms in metallic nitride compounds. The electrochemical behavior of films under simulated body fluid (SBF) conditions was investigated by Open Circuit Potential (OCP) and Electrochemical Impedance Spectroscopy measurements. The measured OCP values increased over time, implying that a passive layer was formed on the surface of the films. It was observed that all films started to passivate in SBF solution, with the HEN6 film exhibiting the highest increase. The highest repassivation potential was exhibited by the same film, implying that it had the highest stability range of all analyzed films. Impedance measurements indicated high corrosion resistance values for HEA2, HEA6, and HEN6 samples. Much lower resistances were found for HEN10 and HEN2. Overall, HEN6 films exhibited the best corrosion behavior among the investigated films. It was noticed that for 24 h of immersion in SBF solution, this film was also a physical barrier to the corrosion process, not only a chemical one.

Microstructure and Mechanical Behavior Comparison between Cast and Additive Friction Stir-Deposited High-Entropy Alloy Al0.35CoCrFeNi.

High-entropy alloys (HEAs) are new alloy systems that leverage solid solution strengthening to develop high-strength structural materials. However, HEAs are typically cast alloys, which may suffer from large as-cast grains and entrapped porosity, allowing for opportunities to further refine the microstructure in a non-melting near-net shape solid-state additive manufacturing process, additive friction stir deposition (AFSD). The present research compares the microstructure and mechanical behavior of the as-deposited AFSD Al0.35CoCrFeNi to the cast heat-treated properties to assess its viability for structural applications for the first time. Scanning electron microscopy (SEM) revealed the development of fine particles along the layer interfaces of the deposit. Quasi-static and intermediate-rate compression testing of the deposited material revealed a significant strain-rate sensitivity with a difference in yield strength of ~400 MPa. Overall, the AFSD process greatly reduced the grain size for the Al0.35CoCrFeNi alloy and approximately doubled the strength at both quasi-static and intermediate strain rates.

Design and Development of Stable Nanocrystalline High-Entropy Alloy: Coupling Self-Stabilization and Solute Grain Boundary Segregation Effects.

Grain growth is prevalent in nanocrystalline (NC) materials at low homologous temperatures. Solute element addition is used to offset excess energy that drives coarsening at grain boundaries (GBs), albeit mostly for simple binary alloys. This thermodynamic approach is considered complicated in multi-component alloy systems due to complex pairwise interactions among alloying elements. Guided by empirical and GB-segregation enthalpy considerations for binary-alloy systems, a novel alloy design strategy, the "pseudo-binary thermodynamic" approach, for stabilizing NC-high entropy alloys (HEAs) and other multi-component-alloy variants is proposed. Using Al25Co25Cr25Fe25 as a model-HEA to validate this approach, Zr, Sc, and Hf, are identified as the preferred solutes that would segregate to HEA-GBs to stabilize it against growth. Using Zr, NC-Al25Co25Cr25Fe25 HEAs with minor additions of Zr are synthesized, followed by annealing up to 1123 K. Using advanced characterization techniques- in situ X-ray diffraction (XRD), scanning/transmission electron microscopy (S/TEM), and atom probe tomography, nanograin stability due to coupling self-stabilization and solute-GB segregation effects is reported in HEAs up to substantially high temperatures. The self-stabilization effect originates from the preferential GB-segregation of constituent HEA-elements that stabilizes NC-Al25Co25Cr25Fe25 up to 0.5Tm (Tm-melting temperature). Meanwhile, solute-GB segregation originates from Zr segregation to NC-Al25Co25Cr25Fe25 GBs; this results in further stabilization of the phase and grain-size (≈14 nm) up to ≈0.58 and ≈0.64Tm, respectively.

Improving Mechanical Properties of Co-Cr-Fe-Ni High Entropy Alloy via C and Mo Microalloying.

The as-cast [Co40Cr25(FeNi)35-yMoy]100-xCx (x = 0, 0.5, y = 3, 4, 5 at.%) HEAs (high-entropy alloys) were prepared by a vacuum arc melting furnace and were then hot rolled. The effect of C and Mo elements on the microstructure evolution and mechanical properties of HEAs was systematically analyzed. The results showed that when no C atoms were added, the HEAs consisted of FCC + HCP dual-phase structure. In addition, as the Mo content increased, the grain size of the alloy increased from 17 µm to 47 µm. However, only the FCC phase appeared after adding 0.5 at.% carbon in Mo microalloyed HEAs, and the grain size of the Mo4C0.5 HEA decreased significantly. Due to the Mo atom content exceeding the solid solution limit, the carbides of Mo combined with the C element appeared in the Mo5C0.5 HEA. The strength of C and Mo microalloyed HEAs significantly increased compared to HEAs with no C added. However, the Mo4C0.5 HEA exhibited excellent comprehensive mechanical properties, which was superior to a majority of reported HEAs and conventional metal alloys. Its yield strength, tensile strength, and elongation were 757 MPa, 1186 MPa, and 69%, respectively. The strengthening mechanism was a combination of fine grain strengthening, TWIP effect, and solid solution strengthening.

Structural Stability of Titanium-Based High-Entropy Alloys Assessed Based on Changes in Grain Size and Hardness.

The thermal stability of the grain structure and mechanical properties of the high-entropy two-phase TiCoCrFeMn alloy produced by powder metallurgy, assessed based on microhardness measurements, was analyzed in this work. For this purpose, material obtained via sintering using the U-FAST method was subjected to long-term heating at a temperature of 1000 °C for up to 1000 h in an argon atmosphere. For homogenization times of 1, 10, 20, 50, 100, and 1000 h, grain size changes in the identified phase components of the matrix were assessed, and microhardness measurements were conducted using the Vickers method. It has been shown that the changes in the analyzed parameters are closely correlated with non-monotonic modifications in the chemical composition. It was found that the tested alloy achieved structural stability after 100 h of annealing. A stable grain size was obtained in the BCC solid solution of approximately 2 µm and the two-phase BCC+C14 mixture of roughly 0.4 µm. Long-term heating for up to 1000 h caused the grain structure to grow to 2.7 µm and 0.7 µm, respectively, with a simultaneous decrease in hardness from 1065 HV to 1000 HV. The chromium and titanium diffusion coefficient values responsible for forming the BCC solid solution and the Laves C14 phase, including the material matrix, were also determined at this level to be DCr = 1.28 × 10-19 (m2·s-1) and DTi = 1.04 × 10-19 (m2·s-1), demonstrating the sluggish diffusion effect typical of high-entropy alloys.

Nanoscale Design for High Entropy Alloy Electrocatalysts.

Due to their distinctive physical and chemical characteristics, high entropy alloys (HEAs), a class of alloys comprising multiple elements, have garnered a lot of attention. It is demonstrated recently that HEA electrocatalysts increase the activity and stability of several processes. In this paper, the most recent developments in HEA electrocatalysts research are reviewed, and the performance of HEAs in catalyzing key reactions in water electrolysis and fuel cells is summarized. In addition, the design strategies for HEA electrocatalysts optimization is introduced, which include component selection, size optimization, morphology control, structural engineering, crystal phase regulation, and theoretical prediction, which can guide component selection and structural design of HEA electrocatalysts.

Defect properties of a body-centered cubic equiatomic TiVZrTa high-entropy alloy from atomistic simulations.

TiVZrTa high-entropy alloys (HEAs) have been experimentally proven to exhibit excellent irradiation tolerance. In this work, defect energies and evolution were studied to reveal the underlying mechanisms of the excellent irradiation tolerance in TiVZrTa HEA via molecular statics calculations and molecular dynamics simulations. The atomic size mismatch of TiVZrTa is ∼6%, suggesting a larger lattice distortion compared to most face-centered cubic and body-centered cubic M/HEAs. Compared to pure Ta and V, smaller vacancy formation and migration energies with large energy spreads lead to higher equilibrium vacancy concentration and faster vacancy diffusion via low-energy migration paths. Vacancies in TiVZrTa have weaker abilities to form large vacancy clusters and prefer to form small clusters, indicating excellent resistance to radiation swelling. The formation energies of different types of dumbbells in TiVZrTa show significant differences and have large energy spreads. The binding abilities of interstitials in TiVZrTa are weaker compared to that in pure Ta and V. In TiVZrTa, fast vacancy diffusion and slow interstitial diffusion result in closer mobilities of vacancies and interstitials, significantly promoting point defect recombination. We further studied the effects of short-range ordered structures (SROs) on defect diffusion and evolution. SROs in TiVZrTa can effectively lead to higher fractions of defect recombination and fewer surviving defects. Our findings provide a comprehensive understanding of the underlying mechanisms of the high irradiation tolerance in body-centered cubic HEAs with large lattice distortion and suggest SROs are beneficial microstructures for enhancing irradiation tolerance.

Effect of WC Content on Microstructure and Properties of CoCrFeNi HEA Composite Coating on 316L Surface via Laser Cladding.

Laser cladding technology is used to fabricate CoCrFeNi HEA/WC composite coatings with different mass fractions of WC on the surface of 316L stainless steel. The microstructures of HEA/WC composite coatings were analyzed by combining multiple characterization techniques. The results show that the HEA/WC composite coatings have good surface formation without pores and hot cracks, and the metallurgical bonding is well formed between the coating and the 316L SS substrate. Under the action of a laser beam and molten pool, WC particles partially or slightly melt and diffuse to the matrix, which hinders the orderly growth of grains and forms multiple strengthening. The phase structure of the HEA/WC composite coatings is composed of a main phase with FCC. The hardness and corrosion resistance of the HEA/WC composite coatings are clearly enhanced, and the HEA/WC composite coating with 5% WC has optimum properties.

Additive Manufacturing Technologies of High Entropy Alloys (HEA): Review and Prospects.

Additive manufacturing (AM) technologies have gained considerable attention in recent years as an innovative method to produce high entropy alloy (HEA) components. The unique and excellent mechanical and environmental properties of HEAs can be used in various demanding applications, such as the aerospace and automotive industries. This review paper aims to inspect the status and prospects of research and development related to the production of HEAs by AM technologies. Several AM processes can be used to fabricate HEA components, mainly powder bed fusion (PBF), direct energy deposition (DED), material extrusion (ME), and binder jetting (BJ). PBF technologies, such as selective laser melting (SLM) and electron beam melting (EBM), have been widely used to produce HEA components with good dimensional accuracy and surface finish. DED techniques, such as blown powder deposition (BPD) and wire arc AM (WAAM), that have high deposition rates can be used to produce large, custom-made parts with relatively reduced surface finish quality. BJ and ME techniques can be used to produce green bodies that require subsequent sintering to obtain adequate density. The use of AM to produce HEA components provides the ability to make complex shapes and create composite materials with reinforced particles. However, the microstructure and mechanical properties of AM-produced HEAs can be significantly affected by the processing parameters and post-processing heat treatment, but overall, AM technology appears to be a promising approach for producing advanced HEA components with unique properties. This paper reviews the various technologies and associated aspects of AM for HEAs. The concluding remarks highlight the critical effect of the printing parameters in relation to the complex synthesis mechanism of HEA elements that is required to obtain adequate properties. In addition, the importance of using feedstock material in the form of mix elemental powder or wires rather than pre-alloyed substance is also emphasized in order that HEA components can be produced by AM processes at an affordable cost.

Mechanical and Corrosion Behavior of Zr-Doped High-Entropy Alloy from CoCrFeMoNi System.

The aim of the paper is to study the Zr addition effect on the mechanical properties and corrosion behavior of a high-entropy alloy from the CoCrFeMoNi system. This alloy was designed to be used for components in the geothermal industry that are exposed to high temperature and corrosion. Two alloys, one Zr-free (named Sample 1) and another one doped with 0.71 wt.% Zr (named Sample 2), were obtained in a vacuum arc remelting equipment from high-purity granular raw materials. Microstructural characterization and quantitative analysis by SEM and EDS were performed. The Young modulus values for the experimental alloys were calculated on the basis of a three-point bending test. Corrosion behavior was estimated by linear polarization test and by electrochemical impedance spectroscopy. The addition of Zr resulted in a decrease in the value of the Young modulus but also in a decrease in corrosion resistance. The beneficial effect of Zr on the microstructure was the grain refinement, and this ensured a good deoxidation of the alloy.

Impact of BSG/CD147 gene expression on diagnostic, prognostic and therapeutic strategies towards malignant cancers and possible susceptibility to SARS-CoV-2.

BACKGROUND: BSG (CD147) is a member of the immunoglobulin superfamily that shows roles for potential prognostics and therapeutics for metastatic cancers and SARS-CoV-2 invasion for COVID-19. The susceptibility of malignant cancers to SARS-CoV-2 as well as the correlations between disease outcome and BSG expression in tumor tissues have not been studied in depth. METHODS: In this study, we explored the BSG expression profile, survival correlation, DNA methylation, mutation, diagnostics, prognostics, and tumor-infiltrating lymphocytes (TILs) from different types of cancer tissues with corresponding healthy tissues. In vitro studies for cordycepin (CD), N6-(2-hydroxyethyl) adenosine (HEA), N6, N6-dimethyladenosine (m62A) and 5'-uridylic acid (UMP) on BSG expression were also conducted. RESULTS: We revealed that BSG is conserved among different species, and significantly upregulated in seven tumor types, including ACC, ESCA, KICH, LIHC, PAAD, SKCM and THYM, compared with matched normal tissues, highlighting the susceptibility of these cancer patients to SARS-CoV-2 invasion, COVID-19 severity and progression of malignant cancers. High expression in BSG was significantly correlated with a short OS in LGG, LIHC and OV patients, but a long OS in KIRP patients. Methylation statuses in the BSG promoter were significantly higher in BRCA, HNSC, KIRC, KIRP, LUSC, PAAD, and PRAD tumor tissues, but lower in READ. Four CpGs in the BSG genome were identified as potential DNA methylation biomarkers which could be used to predict malignant cancers from normal individuals. Furthermore, a total of 65 mutation types were found, in which SARC showed the highest mutation frequency (7.84%) and THYM the lowest (0.2%). Surprisingly, both for disease-free and progression-free survival in pan-cancers were significantly reduced after BSG mutations. Additionally, a correlation between BSG expression and immune lymphocytes of CD56bright natural killer cell, CD56dim natural killer cell and monocytes, MHC molecules of HLA-A, HLA-B, HLA-C and TAPBP, immunoinhibitor of PVR, PVRL2, and immunostimulators of TNFRSF14, TNFRSF18, TNFRSF25, and TNFSF9, was revealed in most cancer types. Moreover, BSG expression was downregulated by CD, HEA, m62A or UMP in cancer cell lines, suggesting therapeutic potentials for interfering entry of SARS-CoV-2. CONCLUSIONS: Altogether, our study highlights the values of targeting BSG for diagnostic, prognostic and therapeutic strategies to fight malignant cancers and COVID-19. Small molecules CD, HEA, m62A and UMP imply therapeutic potentials in interfering with entry of SARS-CoV-2 and progression of malignant cancers.