Seating accuracy of removable partial denture frameworks fabricated by different digital workflows in comparison to conventional workflow.

PURPOSE: To evaluate the seating accuracy of removable partial denture (RPD) frameworks fabricated by two digital workflows involving selective laser melting (SLM) in comparison to the conventional workflow. MATERIALS AND METHODS: A Kennedy class III modification 1 partially edentulous mandibular arch was used as a master model. Three RPD framework groups were included: (1) a conventional workflow group with conventional impression and casting (CC), (2) a partial digital workflow group with conventional impression and digital fabrication (CD), and (3) a complete digital workflow group with digital impression and digital fabrication (DD). A total of 10 frameworks were produced for each group. The marginal gaps at the occlusal rests, retention arms, and reciprocating arms were measured by a traveling microscope. The data were analyzed with the one-way analysis of variance test. RESULTS: At the framework level, the most superior fit was observed for the CD group (79.5 µm) followed by DD (85.3 µm) and CC (114.2 µm) groups. The CD and DD groups were significantly superior to CC (p < 0.001). This fit pattern was consistent for the retention and reciprocating arms, while the occlusal rest fit was similar among all the groups. CONCLUSIONS: The SLM frameworks had a promising seating accuracy in comparison to conventional frameworks. The type of impression, conventional or digital, did not affect the accuracy of SLM frameworks. The differences observed in the present study are likely to be of minimal clinical significance.

Five years of radiographic evaluation for the peri-implant bone changes of all-on-four implant prostheses constructed from different framework materials using different digital construction techniques.

BACKGROUND: There is insufficient evidence recommending a framework material and a CAD/CAM manufacturing technique for mandibular implant-supported prostheses. The study objective was to evaluate the clinical application of different materials and construction techniques used for mandibular All-on-4 prosthesis on circumferential peri-implant bony changes after 5 years. METHODS: Thirty-six male patients with all-on-4 mandibular implant-supported prostheses were recalled and divided into three groups. Group PK (patients with frameworks milled from PEEK blocks), Group PSM (patients with frameworks milled from soft metal blocks), and Group SLM (patients with frameworks constructed with additive manufacturing; selective laser melting). The circumferential bone level on all implant faces was assessed with a CBCT. Two-way repeated measures ANOVA was used to compare vertical bone loss (VBL) and horizontal bone loss (HBL) between different groups, implant positions, and observation times followed by Tukey's multiple comparisons. RESULTS: For all observation times, there was a significant difference in VBL between groups for both anterior and posterior implants (P < .001). For anterior implants, group PSM showed the lowest VBL while group PK showed the highest for anterior and posterior implants. For all groups, HBL significantly increased after 5 years for both anterior and posterior implants (P < .001). For anterior implants, group PSM showed the highest HBL. For posterior implants, group PK and SLM showed the highest. CONCLUSION: Within the study's limitations, mandibular implant-supported fixed frameworks fabricated with either milling from PEEK or soft metal blocks, or additive manufacturing (laser melting technology) exhibited significant vertical and horizontal bone height changes after 5 years. CLINICAL TRIAL REGISTRY NUMBER: (NCT06071689) (11/10/2023).

Optimization design of support structure based on 3D printing technology.

Parts are often warped and deformed when they are molded using selective laser melting (SLM) technology. Thus, it is necessary to study the addition support modes of parts molded using SLM. Consequently, we designed dendritic, E-stage and conical supports, having different structural parameters and different partitions using Magics, and then, we analyzed their performances using the finite element software Abaqus. The structural parameters of the supports were optimized and finally tested using SLM molding technology. The maximum stress concentration was found for dendritic supports, followed by E-stage supports, and then conical supports. The stress concentration and deformation level of Scheme 2 were less than those of Scheme 1. The stress intensity and deformation levels for two partitions were less than those for three partitions. For parts molded by SLM, the deformation was maximum for conical supports, followed by dendritic supports, and then E-stage supports. When gradient supports of similar volumes were added, additional partitions did not effectively improve the molding quality. When supports of similar volumes were added, adding gradient supports did not effectively improve the molding quality. The results provide a basis for the application of SLM in molding high-precision parts.

Effect of temperature on the rheological, textural, and sensory properties of butters from New Zealand market.

Texture and sensory studies at various temperatures are important in evaluating and improving the functionality of butter. While literature is scarce, we evaluated and compared the effect of temperature (5-25°C) on the texture, rheological and sensory properties of commercial butter samples (salted, unsalted, cultured, and spreadable) from the New Zealand market. In addition, the instrumental analyses were compared with the sensory evaluation, to understand the possibility of using instrumental analysis to evaluate consumer liking for different butters. Butter type, temperature, and their type-temperature interaction exhibited significant differences for all instrumental textural parameters. As expected, higher temperature produced softer butter that was more spreadable, liquid-like, less adhesive, less cohesive, had lower storage modulus (G') and lower loss modulus (G″) with the melting of milk fat crystals; however, the rate of change varied for the different butter samples. We have established meltability as the parameter for evaluating butter selection for different applications. The spreadable butter sample exhibited the lowest hardness and G', and highest spreadability (p < .05) at all temperatures, owing to its low solid fat content and the abundance of low-melting triglycerides. The cultured butter sample had the highest melting point, owing to compositional differences. The instrumental and sensory texture analyses were highly correlated, indicating the comparative effectiveness of both approaches for studying the effects of different temperatures on butter textural properties. Overall, our findings provide detailed reference to the dairy industry for butter manufacture, considering variation in fatty acid composition, texture analysis, rheology, and sensory analysis, over the range of storage/usage temperatures.

Novel differential scanning calorimetry (DSC) application to select polyhydroxyalkanoate (PHA) producers correlating 3-hydroxyhexanoate (3-HHx) monomer with melting enthalpy.

Polyhydroxyalkanoate (PHA) is an environmental alternative to petroleum-based plastics because of its biodegradability. The polymer properties of PHA have been improved by the incorporation of different monomers. Traditionally, the monomer composition of PHA has been analyzed using gas chromatography (GC) and nuclear magnetic resonance (NMR), providing accurate monomer composition. However, sequential analysis of the thermal properties of PHA using differential scanning calorimetry (DSC) remains necessary, providing crucial insights into its thermal characteristics. To shorten the monomer composition and thermal property analysis, we directly applied DSC to the analysis of the obtained PHA film and observed a high correlation (r2 = 0.98) between melting enthalpy and the 3-hydroxyhexanoate (3-HHx) mole fraction in the polymer. A higher 3-HHx fraction resulted in a lower melting enthalpy as 3-HHx provided the polymer with higher flexibility. Based on this, we selected the poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (P(3HB-co-3HHx)) producing strain from Cupriavidus strains that newly screened and transformed with vectors containing P(3HB-co-3HHx) biosynthetic genes, achieving an average error rate below 1.8% between GC and DSC results. Cupriavidus sp. BK2 showed a high 3-HHx mole fraction, up to 10.38 mol%, with Tm (℃) = 171.5 and ΔH of Tm (J/g) = 48.0, simultaneously detected via DSC. This study is an example of the expansion of DSC for PHA analysis from polymer science to microbial engineering.

pH-dependent binding of ATP aptamer to the target and competition strands: Fluorescent melting curve fitting study.

The pH varies in different tissues and organelles and also changes during some diseases. In this regard, the application of molecular switches that use a competition-based aptamer switch design in biological systems requires studying the thermodynamics of such systems at different pH values. In this work, we studied the binding of the classical ATP aptamer to ATP and competition strands under different pH and ionic conditions using fluorescent melting curve analysis. We have developed an original approach to processing source data from a PCR thermal cycler. It is based on constructing a thermodynamic model of the melting profile and the subsequent fit of experimental curves within this model. We have shown that this approach enables us to narrow the temperature region under study to the width of the melting region without a significant loss in the quality of the result. This impressively expands the application area of this approach compared to frequently used techniques that require mandatory measurement of the signal outside the melting region. The results obtained by the method showed that the thermodynamic parameters of the ATP aptamer and its duplexes with competition strands change depending on pH. Therefore, molecular switches that use a competition strand to the ATP aptamer may have a pH-dependent sensitivity that has not been previously considered. This should be taken into account for future rational design of similar systems.

Exploring the potential utilization of copigmented barberry anthocyanins in ice cream: Focusing on foaming aspects, and melting attributes.

Anthocyanins have emerged as promising substitutes for synthetic dyes owing to their color profiles, and potential health-boosting properties. The primary aim of this investigation was to assess the impact of copigmented, and un-copigmented barberry anthocyanins, employed at different concentrations (1, 3, and 5% w/w) as colorants in ice cream. The secondary goal was to investigate the influence of barberry anthocyanins on ice cream foaming characteristics, and melting point. The samples' physicochemical, textural, and organoleptic characteristics, total phenolic, and anthocyanin content, and antioxidant activity were determined. By increasing barberry extract concentrations in the samples, the pH levels (5.81) decreased, and overrun increased(30.0 ± 1.15%), respectively. Furthermore, the textural analysis showed that increasing barberry anthocyanins within the ice cream formulation correlated with an increase in sample hardness (113.72 ± 1.34 N). The control sample (vanilla ice cream) had the highest value of melting rate (1.09 ± 0.03 g/min), whereas the specimen containing 5% of copigmented barberry anthocyanins exhibited the lowest rate of melting (0.50 ± 0.01 g/min). The start time of melting of control sample was 1098 s and by increasing the concentration of copigmented barberry anthocyanins from 1 to 5%, this time increased from 1405.2 s to 1831.2 s (P < 0.05). In conclusion, barberry anthocyanins reduced the melting rate as a crucial attribute for ice cream.

Melting and Freezing of a Skyrmion Lattice.

We report comprehensive Monte-Carlo studies of the melting of skyrmion lattices in systems of small, medium, and large sizes with the number of skyrmions ranging from 103to over 105. Large systems exhibit hysteresis similar to that observed in real experiments on the melting of skyrmion lattices. For sufficiently small systems which achieve thermal equilibrium, a fully reversible sharp solid-liquid transition on temperature with no intermediate hexatic phase is observed. A similar behavior is found on changing the magnetic field that provides the control of pressure in the skyrmion lattice. We find that on heating the melting transition occurs via a formation of grains with different orientations of hexagonal axes. On cooling, the fluctuating grains coalesce into larger clusters until a uniform orientation of hexagonal axes is slowly established. The observed scenario is caused by collective effects involving defects and is more complex than a simple picture of a transition driven by the unbinding and annihilation of dislocation and disclination pairs.

Co-melting mechanisms for municipal solid waste incineration fly ash with fine slag from coal gasification and coal gangue.

Vitrification is a promising treatment for municipal solid waste incineration fly ash (MSWI-FA); however, high energy consumption due to the high MSWI-FA fusion temperature limits the development and application of this technique. In this study, fine slag ash (FSA) derived from coal gasification and coal gangue ash (CGA) were mixed with MSWI-FA to reduce the ash fusion temperature. The transformation of minerals in ash during thermal treatment was examined via X-ray diffraction and thermodynamic equilibrium calculations. The ash flow behaviour was observed using a thermal platform microscope, and the silicate structure was quantified using Raman spectra. The co-melting mechanisms for the mixed ash were systematically investigated. Results indicate that the flow temperature (FT) of the mixed ash exhibited an initial decrease and subsequent increase as a function of the addition ratio of FSA or CGA. Lowest ash FT of 1215 °C and 1223 °C were recorded for addition of 50% FSA and 50% CGA, respectively; further, these temperatures were lowered by > 285 °C and >277 °C respectively, relative to FT of the MSWI-FA. The transformation of minerals and silicate structure during mixed ash heating was responsible for the variation in the ash fusion temperature. CaO in MSWI-FA tended to react with mullite, quartz and haematite in FSA and CGA, forming minerals such as anorthite, gehlenite, and andradite with relatively low melting points. The addition of FSA or CGA caused changes in the silicate network structure of the mixed ash. In particular, 50% FSA incorporation caused the transformation of Q4 and Q3 to Q2, whereas 50% CGA introduction resulted in the conversion of Q4 and Q2 into Q3 and Q1 + Q0, respectively. The silicate network depolymerised, causing reduction in the ash fusion temperature and increasing the melting rate.

Controlled Porosity of Selective Laser Melting-Produced Thermal Pipes: Experimental Analysis and Machine Learning Approach for Pore Recognition on Pipes Surfaces.

This study investigates the methods for controlling porosity in thermal pipes manufactured using selective laser melting (SLM) technology. Experiments conducted include water permeability tests and surface roughness measurements, which are complemented by SEM image ML-based analysis for pore recognition. The results elucidate the impact of SLM printing parameters on water permeability. Specifically, an increase in hatch and point distances leads to a linear rise in permeability, while higher laser power diminishes permeability. Using machine learning (ML) techniques, precise pore identification on SEM images depicting surface microstructures of the samples is achieved. The average percentage of the surface area containing detected pores for microstructure samples printed with laser parameters (laser power (W) _ hatch distance (µm) _ point distance (µm)) 175_ 80_80 was found to be 5.2%, while for 225_120_120, it was 4.2%, and for 275_160_160, it was 3.8%. Pore recognition was conducted using the Haar feature-based method, and the optimal patch size was determined to be 36 pixels on monochrome images of microstructures with a magnification of 33×, which were acquired using a Leica S9 D microscope.

Size Reduction to Enhance Crystal-to-Liquid Phase Transition Induced by E-to-Z Photoisomerization Based on Molecular Crystals of Phenylbutadiene Ester.

Harnessing the photoinduced phase transitions in organic crystals, especially the changes in shape and structure across various dimensions, offers a fascinating avenue for exact spatiotemporal control, which is crucial for developing future smart devices. In our study, we report a new photoactive molecular crystal made from (E)-2-(3-phenyl-allylidene)malonate ((E)-PADM). When exposed to ultraviolet (UV) light at 365 nm, this compound experiences an E-to-Z photoisomerization in liquid solution and a crystal-to-liquid phase transition in solid crystals. Remarkably, nanoscopic crystalline rods boost their melting rate and degree compared to bulk crystals, indicating that miniaturization enhances the photoinduced melting effect. Our results demonstrate a simple approach to rapidly drive molecular crystals into liquids via photochemical reactions and phase transitions.

Compressive Behavior of Novel Additively Manufactured Ti-6Al-4V Lattice Structures: Experimental and Numerical Studies.

This paper presents novel configurations for additively manufactured lattice structures, including helical and elliptic designs, in addition to the pyramid base model. Functionally graded versions of the pyramid and elliptic lattice structures are developed by considering desirable relative densities in each layer. The lattice structures were manufactured using Ti-6Al-4V powder in a three-dimensional selective laser melting printer. The averaged porosities are 0.86, 0.91, 0.916, 0.93 and 0.74 for pyramid, functionally graded pyramid, elliptic, functionally graded elliptic and helical, respectively. The mechanical behavior of the lattice structures was characterized through compression tests using a universal testing machine and computationally analyzed using finite element code. The results indicate that the elliptic and functionally graded elliptic lattices have elastic moduli of 0.76 and 0.67 GPa, while the yield strengths are 41.32 and 32.24 MPa, respectively, in comparison to cancellous bone. Moreover, pyramid, functionally graded pyramid, and helical lattices show relatively lower elastic moduli of 0.57, 0.65 and 0.41 GPa and higher yield strengths of 54.1, 52.15 and 61.02 MPa, respectively. This could be an indication that they are fit for cortical bones. All samples have low elastic moduli coupled with high yield strengths. This could reduce or eliminate stress shielding, making them suitable for some load-bearing bio-inspired applications. A comparative study utilizing experimental and numerical models was conducted to evaluate the performance of the proposed designs.

Nanoindentation Creep Behavior of Additively Manufactured H13 Steel by Utilizing Selective Laser Melting Technology.

Nowadays, H13 hot work steel is a commonly used hot work die material in the industry; however, its creep behavior for additively manufactured H13 steel parts has not been widely investigated. This research paper examines the impact of volumetric energy density (VED), a critical parameter in additive manufacturing (AM), and the effect of post heat-treatment nitrification on the creep behavior of H13 hot work tool steel, which is constructed through selective laser melting (SLM), which is a powder bed fusion process according to ISO/ASTM 52900:2021. The study utilizes nanoindentation tests to investigate the creep response and the associated parameters such as the steady-state creep strain rate. Measurements and observations taken during the holding phase offer a valuable understanding of the behavior of the studied material. The findings of this study highlight a substantial influence of both VED and nitrification on several factors including hardness, modulus of elasticity, indentation depth, and creep displacement. Interestingly, the creep strain rate appears to be largely unaltered by these parameters. The study concludes with the observation that the creep stress exponent (n) shows a decreasing trend with an increase in VED and the application of nitrification treatment.

Experimental Study on Preparation of Inorganic Fibers from Circulating Fluidized Bed Boilers Ash.

The ash generated by Circulating Fluidized Bed (CFB) boilers is featured by its looseness and porosity, low content of glassy substances, and high contents of calcium (Ca) and sulfur (S), thus resulting in a low comprehensive utilization rate. Currently, the predominant treatment approach for CFB ash and slag is stacking, which may give rise to issues like environmental pollution. In this paper, CFB ash (with a CaO content of 7.64% and an SO3 content of 1.77%) was used as the main raw material. The high-temperature melting characteristics, viscosity-temperature characteristics, and initial crystallization temperature of samples with different acidity coefficients were investigated. The final drawing temperature range of the samples was determined, and mechanical property tests were conducted on the prepared inorganic fibers. The results show that the addition of dolomite powder has a significant reducing effect on the complete liquid phase temperature. The final drawing temperatures of the samples with different acidity coefficients range as follows: 1270-1318 °C; 1272-1351 °C; 1250-1372 °C; 1280-1380 °C; 1300-1382 °C; and 1310-1384 °C. The drawing temperature of this system is slightly lower than that of basalt fibers. Based on the test results of the mechanical properties of inorganic fibers, the Young's modulus of the inorganic fibers prepared through the experiment lies between 55 GPa and 74 GPa, which basically meets the performance requirements of inorganic fibers. Consequently, the method of preparing inorganic fibers by using CFB ash and dolomite powder is entirely feasible.

Progress in Additive Manufacturing of Magnesium Alloys: A Review.

Magnesium alloys, renowned for their lightweight yet high-strength characteristics, with exceptional mechanical properties, are highly coveted for numerous applications. The emergence of magnesium alloy additive manufacturing (Mg AM) has further propelled their popularity, offering advantages such as unparalleled precision, swift production rates, enhanced design freedom, and optimized material utilization. This technology holds immense potential in fabricating intricate geometries, complex internal structures, and performance-tailored microstructures, enabling groundbreaking applications. In this paper, we delve into the core processes and pivotal influencing factors of the current techniques employed in Mg AM, including selective laser melting (SLM), electron beam melting (EBM), wire arc additive manufacturing (WAAM), binder jetting (BJ), friction stir additive manufacturing (FSAM), and indirect additive manufacturing (I-AM). Laser powder bed fusion (LPBF) excels in precision but is limited by a low deposition rate and chamber size; WAAM offers cost-effectiveness, high efficiency, and scalability for large components; BJ enables precise material deposition for customized parts with environmental benefits; FSAM achieves fine grain sizes, low defect rates, and potential for precision products; and I-AM boasts a high build rate and industrial adaptability but is less studied recently. This paper attempts to explore the possibilities and challenges for future research in AM. Among them, two issues are how to mix different AM applications and how to use the integration of Internet technologies, machine learning, and process modeling with AM, which are innovative breakthroughs in AM.

Temperature-Induced Phase Transition in 2D Alkylammonium Lead Halide Perovskites: A Molecular Dynamics Study.

Molecular dynamics simulations are utilized to unravel the temperature-driven phase transition in double-layered butylammonium (BA) methylammonium (MA) lead halide perovskite (BA)2(MA)Pb2I7, which holds great promise for a wide range of optoelectronics and sensor applications. The simulations successfully capture the structural transition from low to high symmetry phases with rising temperatures, consistent with experimental observations. The phase transition is initiated at two critical interfaces: the first is between the inorganic and organic layers, where the melting of N-H bonds in BA leads to a significant reduction in hydrogen bonding between BA and iodides, and the second is at the interface between the top and bottom organic layers, where the melting of the tail bonds in BA triggers the phase transition. Following this, BA cations exhibit a patterned and synchronized motion reminiscent of a conical pendulum, displaying a mix of ordered and disordered behaviors prior to evolving into a completely molten and disordered state. While the melting of BA cations is the primary driver of the phase transition, the rotational dynamics of MA cations also plays a critical role in determining the phase transition temperature, influenced by the BA-MA interaction. Such an interaction alters the polarization patterns of MA cations across the phase transition. In particular, an antiparallel polarization pattern is observed in the low-temperature phase. Additionally, displacive elements of the phase transition are identified in the simulations, characterized by the shear and distortion of the inorganic octahedra. Notably, at lower temperatures, the octahedral distortion follows a bimodal distribution, reflecting significant variations in distortion among octahedra. This variation is attributed to an anisotropic hydrogen bonding network between iodides and BA cations. Our study reveals the phenomena and mechanisms extending beyond the order-disorder transition mechanism, suggesting potential phase engineering through strategic tuning of organic and inorganic components.

Spatial heterogeneity of per- and polyfluoroalkyl substances caused by glacial melting in Tibetan Lake Nam Co due to global warming.

Per- and polyfluoroalkyl substances (PFASs) in high-latitude polar regions and the Tibetan Plateau have received widespread international attention. Here, we measured 18 PFASs and 11 major isomers in the lake water, sediment, and surrounding runoff of Lake Nam Co in 2020. The concentrations of ultrashort-chain trifluoroacetic acid (TFA) and perfluoropropanoic acid (PFPrA) and major isomers of perfluoooctanoic acid (PFOA) and perfluoooctane sulfonate acid (PFOS) in water bodies in high-latitude polar regions and the Tibetan Plateau are reported for the first time. The results showed that the concentration of ∑PFASs in glacial runoff was approximately 139 % greater than that in nonglacial runoff. The concentrations of ∑PFASs in the lake water and sediment in the southern lake with multiple glacial runoff events were approximately 113 % and 108 % higher, respectively, than those in the northern lake. The concentrations of short-chain perfluorobutanoic acid (PFBA) and ultrashort-chain TFA and PFPrA, which may be indicators of ice and snow melt, exhibited significant spatial heterogeneity. Overall, the spatial heterogeneity of PFAS concentrations in the water, sediment and surrounding runoff of Lake Nam Co may be caused mainly by glacial melting.

Soret-Effect Induced Phase-Change in a Chromium Nitride Semiconductor Film.

Phase-change materials such as Ge-Sb-Te (GST) exhibiting amorphous and crystalline phases can be used for phase-change random-access memory (PCRAM). GST-based PCRAM has been applied as a storage-class memory; however, its relatively low ON/OFF ratio and the large Joule heating energy required for the RESET process (amorphization) significantly limit the storage density. This study proposes a phase-change nitride, CrN, with a much wider programming window (ON/OFF ratio more than 105) and lower RESET energy (one order of magnitude reduction from GST). High-resolution transmission electron microscopy revealed a phase-change from the low-resistance cubic CrN phase into the highly resistive hexagonal CrN2 phase induced by the Soret-effect. The proposed phase-change nitride could greatly expand the scope of conventional phase-change chalcogenides and offer a strategy for the next-generation of PCRAM, enabling a large ON/OFF ratio (∼105), low switching energy (∼100 pJ), and fast operation (∼30 ns).

Successful development of molecular diagnostic technology combining mini-barcoding and high-resolution melting for traditional Chinese medicine agarwood species based on single-nucleotide polymorphism in the chloroplast genome.

Agarwood is a valuable traditional medicine and fragrance. The production process is a typical injury-induced defense response. Currently, there are approximately 22 known species in the genus Aquilaria Lam., all of which can produce agarwood, whereas there are only two legal species of traditional Chinese medicinal agarwood, Aquilaria sinensis (Lour.) Spreng. and Aquilaria agallocha (Lour.) Roxb. The Taiwan herbal Pharmacopoeia of China stipulates that the medicinal agarwood species are A. sinensis and its relatives in the same genus. Moreover, there are five species of agarwood available for clinical medicinal use in Japan, including A. agallocha and A. sinensis, which are often confused with each other or used in a mixed way in the trade process. Therefore, accurate identification of traditional Chinese medicinal agarwood species is important to ensure the authenticity of traditional medicines and to guide the safety of clinical medication. In this study, 59 specific single-nucleotide polymorphism loci were screened and obtained from the chloroplast genomes of 12 species of the genus Aquilaria Lam. We established an identification method for traditional Chinese medicinal agarwood using mini-barcoding combined with high-resolution melting (HRM) and designed and validated 10 pairs of primers from the psbM-trnD, psbA, rps16, petN, ndhE-psaC, rps4, atpE, ycf1, rps15-trnN, and matK regions. The amplification products were all less than 200 bp, with a high success rate of amplification. The method was applied to successfully identify traditional Chinese medicinal agarwood species from commercial agarwood samples. Overall, the sensitivity of this method was sufficient to detect 1% of adulterants in medicinal agarwood products, proving that mini-barcoding HRM is a powerful and flexible tool. This method can be used as a fast and effective high-throughput method for authenticity testing of traditional Chinese medicinal agarwood and its raw materials containing agarwood-containing proprietary Chinese medicines and is recommended for industrial applications.

Revealing of TLR-9 gene polymorphisms by qPCR HRM technique and their influence on TLR-9 serum level in acute myeloid leukemia patients: Case-control study.

Acute myeloid leukemia (AML) is one of the most common and fatal malignancies that affect adults, which can quickly become aggressive if left untreated, and leukemia cells invade the bone marrow. TLR-9 is an innate immune cell receptor sensitive to various PAMPs and encoded by the TLR-9 gene. As is often known, genetic polymorphisms in any gene can help the development of the disease, and these three polymorphisms, rs187084, rs5743836, and rs352140 of TLR-9, have been studied in many different cancer disorders. Therefore, this study aimed to discover the multiple forms of a TLR-9 gene in a sample of Iraqi AML patients. A total of 120 participants in a case-control study were enrolled in the current study. Using CBC, some hematological parameters were evaluated, and the serum level of TLR-9 was assessed using the ELISA technique. DNA was extracted directly from blood, and a high-resolution melting (HRM) analysis was then carried out. The results revealed a significant difference in some blood parameters among patients and healthy control, while WBC and lymphocytes were without an evident difference between the two groups of the current investigation. The serum concentration of TLR-9 showed an elevated level in patients (P value < 0.01). Nonetheless, this increase was not affected by the genotype patterns of polymorphisms. According to the P-value, there was a significant difference in wild genotypes of the three polymorphisms (rs187084, rs5743836, and rs352140). At the same time, the odds ratio revealed the association with the disease as a protective factor. In contrast, there was a significant difference in the heterozygous and mutant genotypes of TLR-9 polymorphisms, though the odds ratio confirmed the association with the AML as a risk factor. The results of rs352140 were compatible with H.W.E since there were no significant differences between the observed and expected values for either patients or healthy controls. In contrast, the result of rs5743836 was not consistent with the HWE. Furthermore, although it corresponds with the healthy one, the finding of rs187084 conflicted with H.W.E. in the patient group. In conclusion, High serum levels of TLR-9 in patients could act as biomarkers for AML. The TLR-9 gene polymorphisms (rs187084, rs5743836, and rs352140) have been linked to an increased risk of AML and may impact the disease progression in the Iraqi population.