Liquid chromatography at the University of Pardubice: A tribute to Professor Pavel Jandera.

Pavel Jandera was a world-leading analytical chemist who devoted his entire professional life to research in the field of high-performance liquid chromatography. During his scientific career, he worked at the Department of Analytical Chemistry at the University of Pardubice, Czech Republic. His greatest contribution to the field of liquid chromatography was the introduction of a comprehensive theory of liquid chromatography with programmed elution conditions. He was also involved in the research of gradient elution techniques in preparative chromatography, modeling of retention and selectivity in various phase systems, preparation of organic monolithic microcolumns, and, last but not least, in the development of theory and practical applications of two-dimensional liquid chromatography, mainly in the comprehensive form. In this review article, we have tried to capture the highlights of his scientific career and provide the readers with a detailed overview of Pavel Jandera's contribution to the evolution of separation sciences.

Kinetic performance comparison of superficially porous, fully porous and monolithic reversed-phase columns by gradient kinetic plots for the separation of protein biopharmaceuticals.

To find the best performing column for the analysis of protein-based biopharmaceuticals is a significant challenge as meanwhile numerous modern columns with distinct stationary phase morphologies are available for reversed-phase liquid chromatography. Especially when besides morphology also several other column factors are different, it is hard to decide about the best performing column a priori. To cope with this problem, in the present work 13 different reversed-phase columns dedicated for protein separations were systematically tested by the gradient kinetic plot method. A comprehensive comparison of columns with different morphologies (monolithic, fully porous and superficially porous particle columns), particle sizes and pore diameters as well as column length was performed. Specific consideration was also given to various monolithic columns which recently shifted a bit out of the prime focus in the scientific literature. The test proteins ranged from small proteins starting from 12 kDa, to medium sized proteins (antibody subunits obtained after IdeS-digestion and disulphide reduction) and an intact antibody. The small proteins cytochrome c, lysozyme and ß-lactoglobulin could be analysed with similar performance by the best columns of all three column morphologies while for the antibody fragments specific fully porous and superficially porous particle columns were superior. A 450 Å 3,5 µm superficially porous particle column showed the best performance for the intact antibody while a 1.7 µm fully porous particle column with 300 Å showed equivalent performance to the best superficially porous column with thin shell and 400 Å pore size for proteins between 12 and 25 kDa. While the majority of the columns had C4 bonding chemistry, the silica monolith with C18 bonding and 300 Å mesopore size approximated the best performing particle columns and outperformed a C4 300 Å wide-pore monolith. The current work can support the preferred choice for the most suitable reversed-phase column for protein separations.

Preparation of a zeolite imidazole skeleton-silica hybrid monolithic column for amino acid analysis via capillary electrochromatography.

We developed a novel, convenient and low-cost one-pot strategy for preparing a zeolitic imidazolate framework-8 (ZIF-8)-silica hybrid monolithic column by adding ZIF-8 directly to a polymer solution of the silica matrix. The simulated stationary phase and monolithic column prepared under optimal conditions were characterized using X-ray diffraction, scanning electron microscopy, Fourier-transform infrared spectroscopy, thermogravimetric analysis nitrogen physisorption and zeta potential. The results obtained confirmed the successful introduction of ZIF-8 into the silica monolithic column, and the prepared monolithic column exhibited good permeability and physicochemical stability. A capillary electrochromatography method was developed based on a ZIF-8-silica hybrid monolithic column through which 15 mixed amino acids, 4 neutral compounds, 4 nipagin esters and 2 chlorinated fungicides were separated in 14, 5, 7 and 6 min, respectively, under optimal conditions. The relative standard deviations retention times and column efficiencies in run-to-run, day-to-day and column-to-column varied in the ranges of 1.90%-2.21%, 2.13%-2.51% and 3.08%-6.65%, respectively, which demonstrated that ZIF-8-silica hybrid monolithic column exhibited satisfactory reproducibility and stability. The incorporation of ZIF-8 into a silica monolithic column is a promising method for preparing novel monolithic columns composed of a metal-organic framework.

Chromatography-Free Purification Strategies for Large Biological Macromolecular Complexes Involving Fractionated PEG Precipitation and Density Gradients.

A complex interplay between several biological macromolecules maintains cellular homeostasis. Generally, the demanding chemical reactions which sustain life are not performed by individual macromolecules, but rather by several proteins that together form a macromolecular complex. Understanding the functional interactions amongst subunits of these macromolecular machines is fundamental to elucidate mechanisms by which they maintain homeostasis. As the faithful function of macromolecular complexes is essential for cell survival, their mis-function leads to the development of human diseases. Furthermore, detailed mechanistic interrogation of the function of macromolecular machines can be exploited to develop and optimize biotechnological processes. The purification of intact macromolecular complexes is an essential prerequisite for this; however, chromatographic purification schemes can induce the dissociation of subunits or the disintegration of the whole complex. Here, we discuss the development and application of chromatography-free purification strategies based on fractionated PEG precipitation and orthogonal density gradient centrifugation that overcomes existing limitations of established chromatographic purification protocols. The presented case studies illustrate the capabilities of these procedures for the purification of macromolecular complexes.

[Fabrication of nanomaterials incorporated polymeric monoliths and application in sample pretreatment].

Polymeric monolithic columns are fabricated by in situ polymerization of the corresponding monomer, crosslinkers, porogenic solvents and radical initiators within a mold. Compared with the conventional packed solid phase extraction adsorbents, polymeric monolithic columns with a continuous porous structure process distinctive advantages of rapid mass transfer and excellent permeability, which facilitates the extraction of trace amounts of the target from the matrix even at high flow velocities. Besides, these materials can be easily fabricated in situ within various cartridges, avoiding a further packing step associated with packed particulate adsorbents. Additionally, the abundant monomer availability, flexible porous structure, and wide applicable pH range make monoliths versatile for use in separation science. Thus, polymeric monolithic columns have been increasingly applied as efficient and promising extraction media for sample pretreatment food, pharmaceutical, biological and environmental analyses. However, these materials usually have the difficulty in morphology control and their interconnected porous micro-globular structure, which may result in low porosity, limited specific surface area and poor efficiency. In addition, polymeric monoliths suffer from the swelling in organic solvents, thus decreasing the service life and precision while increasing the cost consumption. Recently, the development of nanomaterial-incorporated polymeric monoliths with an improved ordered structure, enhanced adsorption efficiency and outstanding selectivity has attracted considerable attention. Nanoparticles are considered as particulates within the size range of 1-100 nm in at least one dimension, which endows them with unique optical, electrical and magnetic properties. These materials have a large surface area, excellent thermal and chemical stabilities, remarkable versatility, as well as a wide variety of active functional groups on their surface. With the aim of exploiting these advantages, researchers have shown great interest in applying nanomaterial-incorporated polymeric monoliths to separation science. Accordingly, significant progress has been achieved in this field. Nanomaterials can be entrapped via the direct synthesis of a polymerization solution that contains well dispersed nanomaterials in porogens. In addition, nanoparticles can be incorporated into the monolithic matrix by copolymerization and post-polymerization modification via specific interactions. Therefore, nanomaterial-incorporated polymeric monoliths combined the different shapes, chemical properties, and physical properties of the polymers with those of the nanoparticles. The presence of nanoparticles can improve the structural rigidity as well as the thermal and chemical stabilities of monolithic adsorbents. Besides, nanoparticles are capable of increasing the specific surface area and providing multiple active sites, which leads to enhanced extraction performance and selectivity of polymeric monolithic materials. In recent years, diverse types of nanomaterials, such as carbonaceous nanoparticles, metallic materials and metal oxides, metal-organic frameworks, covalent organic frameworks and inorganic nanoparticles have been extensively explored as hybrid adsorbents in the modes of solid phase extraction, solid phase microextraction, stir bar sorption extraction and on-line solid phase extraction. This review specifically summarizes the fabrication methods for nanomaterial incorporated polymeric monoliths and their application to the field of sample pretreatment. The existing challenges and future possible perspectives in the field are also discussed.

Supercritical fluid chromatography using methacrylate-based monolithic column for the separation of polar analytes.

A poly(N,N-dimethyl-N-methacryloyloxyethyl-N-(3-sulfopropyl) ammonium betaine-co-ethylene dimethacrylate) monolith was prepared in a 100 × 2.0 mm id stainless-steel column and was investigated for supercritical fluid chromatography. Optimization of its porosity was performed by changing the conditions of polymerization. Then, the chemical group of this column was confirmed by Fourier transform infrared spectroscopy and elemental analysis. The morphology was characterized by scanning electron microscopy. The prepared column showed good repeatability based on the retention factor of adenine, uracil and cytosine to calculate their run-to-run, day-to-day, column-to-column, and batch-to-batch relative standard deviations. Those values were less than 1.9% (n = 10), 6.5% (n = 3), 5.6% (n = 3), and 1.7% (n = 3), respectively. In addition, the column was found to be stable within 3 and 10 days with relative standard deviations less than 6.5 and 8.5%, respectively. These results indicated that the columns showed good reproducibility and stability. Compared with liquid chromatogaphy, supercritical fluid chromatography provided better kinetic performance and selectivity. Finally, several neutral, acid, and basic polar analytes were utilized to test its application. The results demonstrated that the prepared column exhibited a good separation performance and showed great potential in supercritical fluid chromatography.

In situ functionalization of HPLC monolithic columns based on divinylbenzene-styrene-4-vinylbenzyl chloride.

The properties of chromatographic columns are largely determined by functional groups located on the sorbent surface. For monolithic columns, surface functional groups can be created during synthesis stage or by chemical bonding with the complete surface of the sorbent. One of sorbent modification approach is to use on-column click reactions with surface reactive groups. In this study, the surface treatment of monolithic sorbent based on divinylbenzene (DVB), styrene (St) and 4-vinylbenzyl chloride (4VBC) copolymer by heterocyclic nitrogen-containing compounds 1-methylimidazole (1MI), 2-methylimidazole (2MI), 2-methylpyridine (2 MP) and 4-methylpyridine (4 MP) is described. The reaction of nitrogen-containing heterocycles with chloromethyl fragments on the surface results in formation of ion pairs and significantly changes the selectivity of monolithic columns. The chromatographic properties of prepared columns are studied. Modified columns can be operated in reversed-phase (RP) chromatography or in hydrophilic interaction liquid chromatography (HILIC) with different composition of the mobile phase. Separation examples of various chemical substances classes are given.

Fast construction of polymer monolithic columns inside fluorinated ethylene propylene (FEP) tubes for separation of proteins by reversed-phase liquid chromatography.

This paper describes the preparation of polymer monolithic columns in the confines of fluorinated ethylene propylene (FEP) tubes. These tubes are cheap, chemically stable, and widely used in flow analysis laboratories. UV-initiated grafting with 5 wt% benzophenone in methanol for 1 h activated the internal surface walls, thus enabling the further covalent binding of ethylene glycol dimethacrylate (EDMA) from a 15 wt% solution in methanol, also via photografting. Both steps used 254 nm radiation under a potency of 120 mJ cm2. ATR-FTIR measurements revealed the presence of carbonyl, alkyl and vinyl groups in the functionalized FEP. The density of vinyl groups was high enough to firmly attach a poly(lauryl methacrylate-co-ethylene glycol dimethacrylate) monolith in 120 × 1.57 mm i.d. tubes, prepared via photopolymerization. The total preparation lasts less than 2-h. The columns were permeable, (1.58 ± 0.06) × 10-13 m2, providing reproducible chromatographic parameters of retention times, retention factor, selectivity, and resolution. The monoliths were stable at flow rates of 500 µL min-1, collapsing only at flow rates >700 µL min-1, a condition that increased the backpressure over 1000 psi (experiments at the room temperature). The separation of proteins by reversed-phase liquid chromatography demonstrated the efficiency of the columns. Determination of egg white proteins (ovalbumin and lysozyme) and myoglobin in spiked urine proved the applicability to the analysis of real samples.

D-2-allylglycine embedded imidazolium-bridged polyhedral oligomeric silsesquioxane hybrid monolithic column for efficient separation of both small molecules and macromolecules.

The development of multifarious stationary phases is still a growing demand so as to solve the tasks of ever evolving actual applications. Herein, with D-2-allylglycine hydrochloride (AG·HCl) as the hydrophilic monomer, diene ionic liquid 1-allyl-3-vinylimidazolium bromide (AVI·Br) and polyhedral oligomeric silsesquioxane methacryl substituted (POSS-MA) as the dual crosslinkers, the highly cross-linked imidazolium-bridged POSS-AVI-AG hybrid monolithic column was fabricated via the "one-pot" free radical copolymerization. The AG·HCl embedded POSS-AVI-AG column displays typical reversed-phase liquid chromatography/hydrophilic interaction liquid chromatography mixed-mode retention mechanisms. Both hydrophobic phenols, alkylbenzenes, aromatic amines and hydrophilic nucleosides/nucleic acid bases, amides and thioureas were successfully separated with high column efficiencies (up to 571,000 plates/m for amides), outperforming our previously reported AVI·Br modified POSS-AVI column. Moreover, the column was also explored for the separation of cytochrome c tryptic digests and egg white protein extraction. All these results demonstrate that the POSS-AVI-AG column has a good potential in separation of both small molecules and complex biological samples with multiple mechanisms.

Applicability of a Monolithic Column for Separation of Isoquinoline Alkalodis from Chelidonium majus Extract.

Isoquinoline alkaloids are the main group of secondary metabolites present in Chelidonium majus extracts, and they are still the object of interest of many researchers. Therefore, the development of methods for the investigation and separation of the alkaloids is still an important task. In this work, the application potential of a silica-based monolithic column for the separation of alkaloids was assessed. The influence of the organic modifier, temperature, salt concentration, and pH of the eluent on basic chromatographic parameters such as retention, resolution between neighboring peaks, chromatographic plate numbers, and peak asymmetry were investigated. Based on the obtained results, a gradient elution program was developed and used to separate and quantitatively determine the main alkaloids in a Chelidonium majus root extract.

Temperature effects on retention and efficiency of butyl and lauryl acrylate porous polymer monoliths in capillary electrochromatography.

The development of organic porous polymer monoliths represents an alternative approach to stationary phase design. The use of these materials has helped to rekindle interest in capillary electrochromatography. Although a large number of investigations have explored different monolith recipes, polymerization conditions, and application challenges, few investigations have addressed the fundamentals of this separation mode with this type of material. This study addresses the thermodynamics of the reversed phase retention mechanism on 100% butyl acrylate and 1:3 butyl:lauryl acrylate (volume/volume ratio) porous polymer monoliths used in a capillary electrochromatography mode. Linear van't Hoff plots yield enthalpies of retention of -3.9 to -14.3 kJ/mol on two different, but related columns for five selected hydrophobic analytes across a thirty degree temperature range. Minimum plate heights were only moderately impacted over this temperature range.

Modelling retention and peak shape of small polar solutes analysed by nano-HPLC using methacrylate-based monolithic columns.

The development of methacrylate-based monolithic columns was studied for the separation of pharmaceutical hydrophilic compounds in nano-liquid chromatography. The selected polymerisation mixture consisted of 7.5% hexyl methacrylate, 4.5% methacrylic acid and 18.0% ethylene dimethacrylate (w/w), in a binary porogenic solvent (35:35 w/w 1-propanol/1,4-butanediol). The polymer synthesised with this mixture has a good permeability, not excessive back-pressure, and reasonable retention times for polar and non-polar solutes. Monolithic columns (12 cm total capillary length, 100 µm i.d.), prepared with this mixture, were able to produce hydrogen bonding and electrostatic interactions, giving rise to promising separations. To evaluate the chromatographic system, alkylbenzenes (neutral and hydrophobic compounds) and sulphonamides (hydrophilic drugs) were assayed. To optimise the chromatographic mobile phase in isocratic elution and characterise the retention mechanism for a mixture of eight sulphonamides, the performance of several mathematic models was checked in the description of retention. The behaviour of the monolithic capillary column was compared, in terms of selectivity and peak shape, to that obtained with a C18 column (9 cm × 4.6 mm i.d., 5 µm particle size) using a conventional HPLC equipment. The results revealed substantial differences in the interactions established for sulphonamides between the monolithic and C18 columns.

Preparation of restricted-access material precolumns by grafting δ-gluconolactone onto a hybrid silica monolithic column for on-line solid-phase extraction of tetracycline residues from milk.

A restricted-access material-hybrid monolithic column was prepared based on single-component organosiloxane and dynamic grafting of δ-gluconolactone for on-line solid phase extraction of tetracycline antibiotic residues from milk. The hybrid monolithic column was prepared in a stainless-steel chromatographic column using methyltrimethoxysilane as the single precursor. δ-Gluconolactone was covalently coupled to aminopropyl derivatized hybrid monolithic column, which formed hydrophilic structures on the surface of the pore of the restricted-access material-hybrid monolithic column. The columns were characterized by scanning electron microscopy, thermogravimetric analysis, Fourier transform infrared spectroscopy, nitrogen adsorption, contact angle analysis, dynamic adsorption, and chromatographic performance evaluation. The restricted-access material-hybrid monolithic column was applied to the on-line extraction of tetracycline residues from milk. An enrichment factor of 15.8 and a good sample clean-up effect were obtained under the optimized conditions. The recoveries of the three spiked milk samples were between 81.7 and 102.5% with relative standard deviations (n = 3) in the range of 2-5%. The limits of detection (S/N = 3) for target compounds were in the range of 3.80-9.03 µg/kg. The results show that the on-line extraction using the restricted-access material-hybrid monolithic column was powerful for food sample pretreatment with high selectivity and good clean-up effect.

Comprehensive two-dimensional monolithic liquid chromatography of polar compounds.

Two-dimensional liquid chromatography largely increases the number of separated compounds in a single run, theoretically up to the product of the peaks separated in each dimension on the columns with different selectivities. On-line coupling of a reversed-phase column with an aqueous normal-phase (hydrophilic interaction liquid chromatography) column yields orthogonal systems with high peak capacities. Fast on-line two-dimensional liquid chromatography needs a capillary or micro-bore column providing low-volume effluent fractions transferred to a short efficient second-dimension column for separation at a high mobile phase flow rate. We prepared polymethacrylate zwitterionic monolithic micro-columns in fused silica capillaries with structurally different dimethacrylate cross-linkers. The columns provide dual retention mechanism (hydrophilic interaction and reversed-phase). Setting the mobile phase composition allows adjusting the separation selectivity for various polar substance classes. Coupling on-line an organic polymer monolithic capillary column in the first dimension with a short silica-based monolithic column in the second dimension provides two-dimensional liquid chromatography systems with high peak capacities. The silica monolithic C18 columns provide higher separation efficiency than the particle-packed columns at the flow rates as high as 5 mL/min used in the second dimension. Decreasing the diameter of the silica monolithic columns allows using a higher flow rate at the maximum operation pressure and lower fraction volumes transferred from the first, hydrophilic interaction dimension, into the second, reversed-phase mode, avoiding the mobile phase compatibility issues, improving the resolution, increasing the peak capacity, and the peak production rate.

Preparation of a monolithic column with a mixed-mode stationary phase of reversed-phase/hydrophilic interaction for capillary liquid chromatography.

A monolithic capillary column with a mixed-mode stationary phase of reversed-phase/hydrophilic interaction chromatography was prepared for capillary liquid chromatography. The monolith was created by an in-situ copolymerization of a homemade monomer N,N-dimethyl-N-acryloxyundecyl-N-(3-sulfopropyl) ammonium betaine and a crosslinker pentaerythritol triacrylate in a binary porogen agent consisting of methanol and isopropanol. The functional monomer was designed to have a highly polar zwitterionic sulfobetaine terminal group and a hydrophobic long alkyl chain moiety. The composition of the polymerization solution was systematically optimized to permit the best column performance. The columns were evaluated by using acidic, basic, polar neutral analytes, as well as a set of alkylbenzenes and Triton X100. Very good separations were obtained on the column with the mixed-mode stationary phase. It was demonstrated that the mixed-mode stationary phase displayed typic dual retention mechanisms of reversed-phase/hydrophilic interaction liquid chromatography depending on the content of acetonitrile in the mobile phase. The method for column preparation is reproducible.

Poly glycidyl methacrylate-co-ethylene dimethacrylate porous monolith as a versatile platform for the development of separations and solid-phase extractions in sequential injection analyzers.

We demonstrated that the porous structure and the reactivity of the epoxy group in the poly glycidyl methacrylate-co-ethylene dimethacrylate monolith can be a platform for the development of separation and extraction methods based on sequential injection analysis. The epoxy group was functionalized to produce monoliths affording complexing and ion exchange properties. Derivatization with iminodiacetate and sodium sulfite produced weak and strong cation exchangers, respectively. Derivatization with ethylenediamine produced a weak anion exchanger, and the treatment of the ethylenediamine-modified monolith with chloroacetate produced another weak cation exchanger. All the monoliths also worked as chelating sorbents. The columns were prepared inside 50 × 2.01 mm id fused-silica lined stainless steel tubing and exhibited permeabilities between 0.76 and 4.92 × 10-13 m2 , which enabled the application of flow rates between 5 and 15 µL/s by the syringe pumps used in sequential injection analyzers. These columns separated proteins by cation or anion exchange in a sequential injection chromatograph in both synthetic mixtures and in egg white. Additionally, the online solid-phase extraction of copper ions was demonstrated in a sequential injection analyzer with the same columns. Postcolumn derivatization with ethylenediamine and spectrophotometric detection was used for the copper detection.

Application of steric exclusion chromatography on monoliths for separation and purification of RNA molecules.

Steric exclusion chromatography (SXC) is a method for separation of large target solutes based on their association with a hydrophilic stationary phase through mutual steric exclusion of polyethylene glycol (PEG). Selectivity in SXC is determined by the size or shape (or both) of the solutes alongside the size and concentration of PEG molecules. Elution is achieved by decreasing the PEG concentration. In this study, SXC applicability for the separation and purification of single-stranded (ss) and double-stranded (ds) RNA molecules was evaluated for the first time. The retention of ssRNA and dsRNA molecules of different lengths on convective interaction media (CIM) monolithic columns was systematically studied under variable PEG-6000 and NaCl concentrations. We determined that over 90% of long ssRNAs (700-6374 nucleotides) and long dsRNAs (500-6374 base pairs) are retained on the stationary phase in 15% PEG-6000 and ≥0.4 M NaCl. dsDNA and dsRNA molecules of the same length were partially separated by SXC. Separation of RNA molecules below 100 nucleotides from longer RNA species is easily achieved by SXC. Furthermore, SXC has the potential to separate dsRNAs from ssRNAs of the same length. We also demonstrated that SXC is suitable for the enrichment of ssRNA (PRR1 bacteriophage) and dsRNA (Phi6 bacteriophage) viral genomes from contaminating cellular RNA species. In summary, SXC on CIM monolithic columns is an appropriate tool for rapid RNA separation and concentration.

Poly[(2-(acryloyloxy) ethyl]trimethylammonium chloride-co-ethylene dimethacrylate monolith on-line solid-phase extraction coupled with liquid chromatography and tandem mass spectrometry for the fast determination of salicylic acid in foodstuffs.

We report the fabrication of an anion-exchange monolithic column in a stainless-steel chromatographic column (10 mm × 2.1 mm i.d.) using [2-(acryloyloxy) ethyl]trimethylammonium chloride as the monomer and ethylene dimethacrylate as the crosslinker. The prepared monolith was developed as the adsorbent for the on-line solid-phase extraction of salicylic acid in various animal-origin foodstuffs combined with liquid chromatography and tandem mass spectrometry. The monolith was characterized by using Fourier transform infrared spectroscopy, scanning electron microscopy, nitrogen adsorption analysis, and elemental analysis. Potential factors affecting the on-line solid-phase extraction and liquid chromatography with tandem mass spectrometry analysis were studied in detail. Under the optimized conditions, the total analysis time including cleanup and liquid chromatography with tandem mass spectrometry separation was 17 min. The developed method gave the linear range of 15-750 µg/kg, detection limits (S/N = 3) of 5 µg/kg, and quantification limits (S/N = 10) of 15 µg/kg. The recoveries obtained by spiking 10, 20, and 100 µg/kg of salicylic acid in the animal-origin food samples were in the range of 85.2-98.4%. In addition, the monolith was stable enough for 550 extraction cycles with the precision of peak area ≤11.6%.

Preparation and characterization of vinylimidazole-based polymer monolithic stationary phases for reversed-phase and hydrophilic interaction capillary liquid chromatography.

In this study, we applied 1-vinylimidazole (VIM) as the functional monomer to prepare a series of VIM-based monolithic stationary phases for both reversed-phase and hydrophilic interaction capillary liquid chromatography (LC) using various dimethacrylates (EDMA: ethylene dimethacrylate; HDDMA: 1,6-hexanediol dimethacrylate; DDDMA: 1,10-decanediol dimethacrylate) as cross-linkers. With a simple thermally initiated free-radical cross-linking polymerization process, VIM-based monolithic stationary phases have been successfully prepared. The porosity, permeability, and column efficiency of synthesized VIM-based monolithic stationary phases were characterized. With similar total porosity (85-90%), the VIM-HDDMA monoliths showed the lowest permeability among the three sets of VIM-based stationary phases. Various sets of non-polar (alkyl benzenes and polycyclic aromatic hydrocarbons) and polar analytes (phenol derivatives and amphenicol antibiotics) were applied as model compounds to further investigate the retention behavior of the VIM-based monolithic stationary phases for reversed-phase capillary LC analysis using selected VIM-based monolithic columns. While a mixture of organic acids was employed to perform HILIC analysis using the selected VIM-based monolithic columns. The separation selectivity and retention behavior of the VIM-based monolithic stationary phases were compared to those obtained using three previously prepared alkyl methacrylate-based monolithic columns. Strong retention and good resolution of polar analytes (such as phenol derivatives, amphenicol antibiotics, and organic acids) were observed using the selected VIM-based monolithic columns. The strong retention and good resolution might be attributed to the additional hydrogen-bonding between the hydrogen-donating analytes and the hydrogen-accepting imidazolium functionality on the VIM-based stationary phase. The applicability for both reversed-phase and HILIC capillary LC analysis has also been demonstrated using the selected VIM-based monolithic columns.

Preparation of an acryloyl ß-cyclodextrin-silica hybrid monolithic column and its application in pipette tip solid-phase extraction and HPLC analysis of methyl parathion and fenthion.

An acryloyl ß-cyclodextrin-silica hybrid monolithic column for pipette tip solid-phase extraction and high-performance liquid chromatography determination of methyl parathion and fenthion has been prepared through a sol-gel polymerization method. The synthesis conditions, including the volume of cross-linker and the ratio of inorganic solution to organic solution, were optimized. The prepared monolithic column was characterized by thermogravimetric analysis, scanning electron microscopy, and Fourier transform infrared spectroscopy. The eluent type, volume and flow rate, sample volume, flow rate, acidity, and ionic strength were optimized in detail. Under the optimized conditions, a simple and sensitive pipette tip solid-phase extraction with high-performance liquid chromatography method was developed for the determination of methyl parathion and fenthion in lettuce. The method yielded a linear calibration curve in the concentration ranges of 15-400 µg/kg for methyl parathion and 20-400 µg/kg for fenthion with correlation coefficients of above 0.9957. The limits of detection were 4.5 µg/kg for methyl parathion and 6.0 µg/kg for fenthion, respectively. The recoveries of methyl parathion and fenthion spiked in lettuce ranged from 96.0 to 104.2% with relative standard deviations less than 8.4%.