Optimization of nitrogen-doped sludge char preparation and mechanism study for catalytic oxidation of NO at room temperature.

Catalytic oxidation of NO at room temperature was carried out over nitrogen (N)-doped sludge char (SC) prepared from pyrolysis of municipal sewage sludge, and urea was adopted as nitrogen source. The effects of different N-doping methods (one-step and two-step method), dried sludge (DS)/urea mass ratios (5:1, 4:1, 3:1, 2:1, and 1:1), SC preparation procedures (pyrolysis only, pyrolysis with acid washing, and pyrolysis with KOH activation and acid washing), and different pyrolysis temperatures (500, 600, 700, and 800°C) on the catalytic oxidation of NO were compared to optimize the procedure for SC preparation. The results indicated that N-doping could obviously promote the catalytic performance of SC. The one-step method with simultaneous sludge pyrolysis (at 700°C), KOH activation, and N-doping (DS/urea of 3:1) was the optimal procedure for preparing the N-doped SC with the NO conversion rate of 54.7%, whereas the optimal NO conversion rate of SC without N-doping was only 47.3%. Urea worked both as carbon and nitrogen source, which could increase about 2.9%-16.5% of carbon and 24.8%-42.7% of nitrogen content in SC pyrolyzed at 700°C. N-doping significantly promoted microporosity of SC. The optimal N-doped SC showed specific surface areas of 571.38 m2/g, much higher than 374.34 m2/g of the optimal SC without N-doping. In addition, N-doping also increased amorphousness and surface basicity of SC through the formation of N-containing groups. Finally, three reaction paths, i.e. microporous reactor, active sites, and basic site control path, were proposed to explain the mechanism of N-doping on promoting the catalytic performance of NO.

Optimizing cooperative catalysis of multiple defective interfaces in Pt/mullite catalysts for NO oxidation.

Nitric oxide (NO) oxidation is an integral part of the nitrogen chemical cycle, but competitive activation of NO/O2 over single platinum (Pt)-based catalysts result in inadequate low temperature performance. Here, we constructed catalysts with BiMn2O5/CeO2 and Pt/BiMn2O5 defective interfaces (sufficient activation of NO/O2). The constructed catalyst achieved 95 % NO conversion at 260 °C in NO/O2 atmosphere, superior to most known catalysts. Even after aging (800 °C for 16 h), the NO conversion was up to 76 %. Further, the catalyst can be applied to actual diesel exhaust. Detailed oxygen vacancies (Ov) characterization reveals that BiMn2O5/CeO2 defective interface created by Ce3+-Ov + Mn4+-O ↔ Ce4+-O + Mn3+-Ov promote the activation of NO (on Mn3+ sites) and O2 (on Mn3+-Ov sites). Besides, the Ov on Pt/BiMn2O5 defective interface compensate for the loss of Pt sites ensuring hydrothermal stability. And this construction of multiple defective interfaces develops a pathway for boosting catalytic reactions.

Synthesis of La1-xSrxCoO3-δ and its catalytic oxidation of NO and its reaction path.

The oxidation rate of NO to NO2 is a critical parameter in the removal of NOx within selective catalytic reduction (SCR) systems. LaCoO3-δ is a kind of potential catalyst to enhance the oxidation of NO to NO2, it may offers an economic and stable alternative to noble metal catalysts, particularly at elevated temperatures. This study aimed to enhance the catalytic efficiency of LaCoO3-δ through strontium (Sr) doping. La1-xSrxCoO3-δ (with varying x values of 0.1, 0.2, 0.3, 0.4) was synthesized using a sol-gel method. La1-xSrxCoO3-δ exhibited superior NO oxidation catalytic activity compared to LaCoO3-δ, with the most notable enhancement observed at x = 0.3 (84 % conversion). This improvement can be attributed to the substitution of La3+ with Sr2+, which induces lattice distortion and charge imbalance, thereby creating more oxygen vacancies that enhance the catalytic oxidation capability of La1-xSrxCoO3-δ. However, it's important to note that an excessive amount of Sr can result in the formation of SrCO3 deposits on the surface of La1-xSrxCoO3-δ, thereby diminishing its catalytic oxidation performance. The catalytic oxidation reaction behavior adhered most closely to the O2-adsorbed E-R model, the surface defects in La1-xSrxCoO3-δ playing a pivotal role in the catalytic reaction.

Built-in electric field mediated S-scheme charge migration and Co-N4(II) sites in cobalt phthalocyanine/MIL-68(In)-NH2 heterojunction for boosting photocatalytic nitric oxide oxidation.

The efficiency of photocatalytic Nitric Oxide(NO) oxidation is limited by the lack of oxygen(O2) active sites and poor charge carrier separation. To address this challenge, we developed a molecular Cobalt Phthalocyanine modified MIL-68(In)-NH2 photocatalyst with a robust Built-in electric field(BIEF). In the 2 % CoPc-MIN sample, the BIEF strength is increased by 3.54 times and 5.83 times compared to pristine CoPc and MIL-68(In)-NH2, respectively. This BIEF facilitates the efficient S-scheme charge transfer, thereby enhancing photogenerated carrier separation. Additionally, the Co-N4(II) sites in CoPc can effectively trap the separated photoexcited electrons in the S-scheme system. In addition, the Co-N4(II) sites can also serve as active sites for O2 adsorption and activation, promoting the generation of superoxide radical (O2-), thereby driving the direct conversion of NO to nitrate(NO3-). Consequently, the 2 % CoPc-MIN sample exhibits a remarkable photocatalytic NO removal efficiency of 79.37 % while effectively suppressing the formation of harmful by-product nitrogen dioxide(NO2) to below 3.5 ppb. This study provides a feasible strategy for designing high-efficiency O2 activation photocatalysts for NO oxidation.

Hydrochars derived from real organic wastes as carbonaceous precursors of activated carbons for the removal of NO from contaminated gas streams.

The improvement of air quality in densely-populated urban regions constitutes an environmental challenge of increasing concern. In this respect, the abatement of NO emissions, primarily emanating from combustion processes associated with motor-vehicles, along with industrial/domestic combustion systems, represents one of the main problems. Here, three hydrochars from diverse organic residues were used as activated carbon precursors for their evaluation in the NO removal in two potential application scenarios. Hydrochars were physically activated at 800 °C with pure-CO2 or diluted-O2. These materials were tested in a lab-scale biofilter at different conditions (NO concentration, temperature, relative humidity, NO-containing gas and carbon particle size) and in a larger-scale biofilter to evaluate the long-term NO removal capacity. Hydrochar-derived carbons present a relatively well-developed micro- and mesoporous structure, with BET areas of up to 421 m2/g, and a variety of oxygen surface functionalities (carboxylic, lactone, carbonyl and quinone groups), especially concerning CO2-activated carbons. These exhibited an excellent behaviour at low NO concentration (5 ppmv) between 25 and 75 °C with removal capacities of ≈97 % and > 82 %, respectively; and still good-performance (≈66 %) in a more concentrated gas (120 ppmv). Whilst, carbons obtained by diluted-O2 activation from the same hydrochars, evidenced a higher removal capacity loss at high NO concentration. The O2 presence in the gas stream was confirmed as a crucial factor in the NO elimination, since both co-adsorb on the carbon surface favouring NO oxidation to NO2. Besides, the humidity in the airstream diminished the NO removal capacity from 0.88 to 0.51 mgNO/gcarbon, but still remained at 0.54 mgNO/gcarbon, when the carbon (in pellet) was operated at larger-scale biofilter in 9-fold longer test under humid air. Therefore, this study highlights the potential of renewable carbons to serve as cost-effective component in urban biofilters, to mitigate NO emissions from exhaust gases in biomass boilers and urban semi-close areas.

S-Scheme heterojunction of Cs2SnBr6/C3N4 with interfacial electron exchange toward efficient photocatalytic NO abatement.

Photocatalytic technology is of great significance in environmental purification due to its eco-friendly and cost-effective operations. However, low charge-transfer efficiency restricts the photocatalytic activity of the catalyst. Herein, we report Cs2SnBr6/C3N4 composite catalysts that exhibit a robust interfacial electron exchange thereby enhancing photocatalytic nitric oxide (NO) oxidation. A comprehensive study has demonstrated the S-scheme electron transfer mechanism. Benefiting from the interfacial internal electric field, the C-Br bond serves as a direct electron transfer channel, resulting in enhanced charge separation. Furthermore, the S-scheme heterojunction effectively traps high redox potential electrons and holes, leading to the production of abundant reactive oxygen radicals that enhance photocatalytic NO abatement. The NO removal rate of the Cs2SnBr6/C3N4 heterogeneous system can reach 86.8 %, which is approximately 3-fold and 18-fold that of pristine C3N4 and Cs2SnBr6, respectively. The comprehensive understanding of the electron transfer between heterojunction atomic interfaces will provide a novel perspective on efficient environmental photocatalysis.

Application of TiO2 Supported on Nickel Foam for Limitation of NOx in the Air via Photocatalytic Processes.

TiO2 was loaded on the porous nickel foam from the suspended ethanol solution and used for the photocatalytic removal of NOx. Such prepared material was heat-treated at various temperatures (400-600 °C) to increase the adhesion of TiO2 with the support. Obtained TiO2/nickel foam samples were characterized by XRD, UV-Vis/DR, FTIR, XPS, AFM, SEM, and nitrogen adsorption at 77 K. Photocatalytic tests of NO abatement were performed in the rectangular shape quartz reactor, irradiated from the top by UV LED light with an intensity of 10 W/m2. For these studies, a laminar flow of NO in the air (1 ppm) was applied under a relative humidity of 50% and a temperature of 28 °C. Concentrations of both NO and NO2 were monitored by a chemiluminescence NO analyzer. The adsorption of nitrogen species on the TiO2 surface was determined by FTIR spectroscopy. Performed studies revealed that increased temperature of heat treatment improves adhesion of TiO2 to the nickel foam substrate, decreases surface porosity, and causes removal of hydroxyl and alcohol groups from the titania surface. The less hydroxylated surface of TiO2 is more vulnerable to the adsorption of NO2 species, whereas the presence of OH groups on TiO2 enhances the adsorption of nitrate ions. Adsorbed nitrate species upon UV irradiation and moisture undergo photolysis to NO2. As a consequence, NO2 is released into the atmosphere, and the efficiency of NOx removal is decreasing. Photocatalytic conversion of NO to NO2 was higher for the sample heated at 400 °C than for that at 600 °C, although coverage of nickel foam by TiO2 was lower for the former one. It is stated that the presence of titania defects (Ti3+) at low temperatures of its heating enhances the adsorption of hydroxyl groups and the formation of hydroxyl radicals, which take part in NO oxidation. Contrary to that, the presence of titania defects in TiO2 through the formation of ilmenite structure (NiTiO3) in TiO2/nickel foam heated at 600 °C inhibits its photocatalytic activity. No less, the sample obtained at 600 °C indicated the highest abatement of NOx due to the high and stable adsorption of NO2 species on its surface.

Boosting photocatalytic NO oxidation mediated by high redox charge carriers from visible light-driven C3N4/UiO-67 S-scheme heterojunction photocatalyst.

The construction of CN/UiO-67 (CNU) S-scheme heterojunction composites through in situ formation of UiO-67 on carbon nitride (C3N4) helps to address the limitations of carbon nitride (CN) in photocatalytic NO elimination. The optimized CNU3 demonstrates superior photocatalytic efficiency, which is attributed to electronic channels constructed by Zr-N bonds and S-scheme electron transport mechanism, effectively promoting the efficient separation of photogenerated charge carriers with high redox potentials. Density Functional Theory (DFT) calculations reveal redistributed electronic orbitals in CNU3, with progressive and continuous energy levels near the Fermi level, which bolsters electronic conduction. Comprehensive quenching experiments, Electron Paramagnetic Resonance (EPR), and in situ Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS) analyses highlight a synergistic interplay of electrons, holes, and superoxide radicals in CNU3, inhibiting the generation of toxic nitrogen oxide intermediates and culminating in highly efficient photocatalytic NO oxidation. This study not only elucidates the mechanisms underpinning the enhanced performance of CNU3 heterojunctions but also offers new perspectives on the preparation and interfacial charge separation of heterojunction photocatalysts.

Selective Electrocatalytic Conversion of Nitric Oxide to High Value-Added Chemicals.

The artificial disturbance in the nitrogen cycle has necessitated an urgent need for nitric oxide (NO) removal. Electrochemical technologies for NO conversion have gained increasing attention in recent years. This comprehensive review presents the recent advancements in selective electrocatalytic conversion of NO to high value-added chemicals, with specific emphasis on catalyst design, electrolyte composition, mass diffusion, and adsorption energies of key intermediate species. Furthermore, the review explores the synergistic electrochemical co-electrolysis of NO with specific carbon source molecules, enabling the synthesis of a range of valuable chemicals with C─N bonds. It also provides in-depth insights into the intricate reaction pathways and underlying mechanisms, offering valuable perspectives on the challenges and prospects of selective NO electrolysis. By advancing comprehension and fostering awareness of nitrogen cycle balance, this review contributes to the development of efficient and sustainable electrocatalytic systems for the selective synthesis of valuable chemicals from NO.

Understanding the effects of A-site Ag-doping on LaCoO3 perovskite for NO oxidation: Structural and magnetic properties.

The partial substitution of A-site in perovskites is a major strategy to enhance the catalytic oxidation activity. This study explores the use of silver (Ag) to partially replace the lanthanum (La) ion at the A-site in LaCoO3 perovskite, investigating the role of Ag in the ABO3 perovskite structure, elucidating the nitric oxide (NO) oxidation mechanism over La1-xAgxCoO3 (x = 0.1-0.5) perovskites. La0.7Ag0.3CoO3 with an Ag-doping amount of 0.3, exhibited the highest NO oxidation activity of 88.5% at 275 °C. Characterization results indicated that Ag substitution enhanced the perovskite, maintaining its original phase structure, existing in the form of a mixture of Ag0 and Ag+ in the La1-xAgxCoO3 (x = 0.1-0.5) perovskites. Notably, Ag substitution improved the specific surface area, reduction performance, Co3+, and surface adsorption oxygen content. Additionally, the study investigated the relationship between magnetism and NO oxidation from a magnetism perspective. Ag-doping strengthened the magnetism of La-Ag perovskite, resulting in stronger adsorption of paramagnetic NO. This study elucidated the NO oxidation mechanism over La-Ag perovskite, considering structural and magnetic properties, providing valuable insights for the subsequent development and industrial application of high oxidation ability perovskite catalysts.

Surface Hydrogen Bond-Induced Oxygen Vacancies of TiO2 for Two-Electron Molecular Oxygen Activation and Efficient NO Oxidation.

Defect engineering can provide a feasible approach to achieving ambient molecular oxygen activation. However, conventional surface defects (e.g., oxygen vacancies, OVs), featured with the coordinatively unsaturated metal sites, often favor the reduction of O2 to •O2- rather than O22- via two-electron transfer, hindering the efficient pollutant removal with high electron utilization. Herein, we demonstrate that this bottleneck can be well discharged by modulating the electronic structure of OVs via phosphorization. As a proof of concept, TiO2 nanoparticles are adopted as a model material for NaH2PO2 (HP) modification, in which HP induces the formation of OVs via weakening the Ti-O bonds through the hydrogen bond interactions. Additionally, the formed Ti-O-P covalent bond refines the electronic structure of OVs, which enables rapid electron transfer for two-electron molecular oxygen activation. As exemplified by NO oxidation, HP-modified TiO2 with abundant OVs achieved complete NO removal with high selectivity for benign nitrate, superior to that of pristine TiO2. This study highlights a promising approach to regulate the O2 activation via an electronic structure modulation and provides fresh insights into the rational design of a photocatalyst for environmental remediation.

Triangle Cl-Ag1 -Cl Sites for Superior Photocatalytic Molecular Oxygen Activation and NO Oxidation of BiOCl.

BiOCl photocatalysis shows great promise for molecular oxygen activation and NO oxidation, but its selective transformation of NO to immobilized nitrate without toxic NO2 emission is still a great challenge, because of uncontrollable reaction intermediates and pathways. In this study, we demonstrate that the introduction of triangle Cl-Ag1 -Cl sites on a Cl-terminated, (001) facet-exposed BiOCl can selectively promote one-electron activation of reactant molecular oxygen to intermediate superoxide radicals (⋅O2 - ), and also shift the adsorption configuration of product NO3 - from the weak monodentate binding mode to a strong bidentate mode to avoid unfavorable photolysis. By simultaneously tuning intermediates and products, the Cl-Ag1 -Cl-landen BiOCl achieved >90 % NO conversion to favorable NO3 - of high selectivity (>97 %) in 10 min under visible light, with the undesired NO2 concentration below 20 ppb. Both the activity and the selectivity of Cl-Ag1 -Cl sites surpass those of BiOCl surface sites (38 % NO conversion, 67 % NO3 - selectivity) or control O-Ag1 -O sites on a benchmark photocatalyst P25 (67 % NO conversion and 87 % NO3 - selectivity). This study develops new single-atom sites for the performance enhancement of semiconductor photocatalysts, and also provides a facile pathway to manipulate the reactive oxygen species production for efficient pollutant removal.

Removal of NO at low concentrations from polluted air in semi-closed environments by activated biochars from renewables feedstocks.

Efficient measures are urgently required in large cities for nitric oxide (NO) elimination from air in urban semi-closed environments (parking lots and tunnels), characterized by low NO concentrations (<10 ppmv) and temperatures. One of the most promising abatement alternatives is the NO oxidation to NO2, which can be further easily captured in an alkali solution or over a porous solid. However, most of the research devoted to this topic is focused on the elimination of NO from fuel exhaust gases, with high NO concentrations (400-2000 ppmv). In this work, sustainable and low-cost activated biochars of different origin and having very different ash contents were employed in NO removal at very low concentrations. Thus, low ash content forestry (oak woodchips, OAK) and high ash content from agriculture (oilseed rape straw, OSR) biochars were subjected to physical activation with CO2 at 900 °C (OAK550-A900CO2 and OSR700-A900CO2, respectively). The NO removal performance tests of such activated carbons were carried out at different experimental conditions: i.e., temperature, relative humidity (0-50 vol% RH), NO-containing gas (N2 or air), amount of activated carbon, and NO concentration, to assess how the activated biochar properties influence their NO removal capacity. The sample OSR700-A900CO2 contained a higher population of oxygen surface functionalities, which might play an important role in the NO removal efficiency in dry conditions since they could assist NO oxidation on carbon active sites when used above room temperature (50-75 °C). However, at room temperature (25 °C), the presence of narrow micropore size distribution at 6 Å became a more relevant property, since it facilitates an intimate contact between NO and O2. Accordingly, the activated biochar from OAK was much more efficient, achieving complete removal of NO from air flow (dry or with 50 vol% RH) at 25 °C during 400 min of testing, making it an ideal candidate as biofilter for purifying air streams of semi-closed spaces contaminated with low concentrations of NO.

Br vacancy engineering in Cs3Bi2Br9 for photocatalytic NO oxidation under visible light.

Photocatalysis using the visible light of the sun is an environmentally friendly method of eliminating the NOx pollutant from the ambient air. Although Cs3Bi2Br9, a semiconductor with a band gap of 2.54 eV, may be a strong absorber of visible light, its photocatalysis towards the abatement of NOx is unknown. In this study, Cs3Bi2-xPbxBr9-x (0 ≤ x ≤ 0.0789) are used for the photocatalytic oxidation of NOx. A significant NO oxidation efficiency (80%) is observed over Cs3Bi2-xPbxBr9-x (x = 0.0443) under visible light, which is attributable to the Br vacancy (VBr) brought about by Pb2+ doping. The presence of VBr increased the ionic selectivity of in the oxidized NO. At higher Pb doping level, two HONOs adsorbed on the VBr, linked, and then reduced by hot electrons to produce N2O22-. The di-azo coupling could passivate the activation of NO on the VBr. This work advances the defect engineering of halide for the photo-driving solid-gas reaction in air.

Removal of NO at low concentration from air in urban built environments by activated miscanthus biochar.

This work presents an innovative and sustainable approach to remove NO emissions from urban ambient air in confined areas (underground parking areas or tunnels) using low-cost activated carbons obtained from Miscanthus biochar (MSP700) by physical activation (with CO2 or steam) at temperatures ranging from 800 to 900 °C. The NO removal capacity of the activated biochars was evaluated under different conditions (temperature, humidity and oxygen concentration) and compared against a commercial activated carbon. This last material showed a clear dependence on oxygen concentration and temperature, exhibiting a maximum capacity of 72.6% in air at 20 °C, whilst, its capacity notably decreased at higher temperatures, revealing that physical NO adsorption is the limiting step for the commercial sample that presents limited oxygen surface functionalities. In contrast, MSP700-activated biochars reached nearly complete NO removal (99.9%) at all tested temperatures in air ambient. Those MSP700-derived carbons only required low oxygen concentration (4 vol%) in the gas stream to achieve the full NO removal at 20 °C. Moreover, they also showed an excellent performance in the presence of H2O, reaching NO removal higher than 96%. This remarkable activity results from the abundance of basic oxygenated surface groups, which act as active sites for NO/O2 adsorption, along with the presence of a homogeneous microporosity of 6 Å, which enables intimate contact between NO and O2. These features promote the oxidation of NO to NO2, which is further retained over the carbon surface. Therefore, the activated biochars studied here could be considered promising materials for the efficient removal of NO at low concentrations from air at moderate temperatures, thus closely approaching real-life conditions in confined spaces.

Understanding structure-performance relationships of CoOx/CeO2 catalysts for NO catalytic oxidation: Facet tailoring and bimetallic interface designing.

Crystalline structure and bimetallic interaction of metal oxides are essential factors to determine the catalytic activity. Herein, three different CoOx/CeO2 catalysts, employing CeO2 nanorods (predominately exposed {110 facet), CeO2 nanopolyhedra ({111} facet) and CeO2 nanocubes ({100} facet) as the supports, are successfully prepared for investigating the effect of exposed crystal facets and bimetallic interface interaction on NO oxidation. In comparison with the {111} and {100} facets, the exposed crystal facet {110} exists the best superiority to anchor and stabilize Co species. Moreover, ultra-small CoOx clusters composed of strong Co-O coordination shells with minor Co-O-Ce interaction are formed and uniformly dispersed on the CeO2 nanorods. Structural characterizations reveal that the active exposed crystal facet {110} and the strong bimetallic interface interaction in CoOx/CeO2-nanorods (R-CC) result in more structural defect, endowing it with abundant oxygen vacancies, excellent reducibility and strong adsorption capacity. The DRIFTs spectra further indicate that the exposed crystal facet {110} has a significant promoting effect on the strength of nitrates compared with {111} and {100} facets. The bimetallic interface interaction not only significantly facilitates the formation of nitrate species at lower temperature, but also effectively suppresses the generation of sulfate and lower the sulphation rate. Therefore, R-CC catalyst exhibits the maximum NO oxidation activity with the conversion of 86.4 % at 300 °C and still sustains its high activity under cyclic condition or 50 ppm SO2. The provided crystalline structure and interaction-enhanced strategy sheds light on the design of high-activity NO oxidation catalysts.

Study on the characteristics of zeolite-promoted thermal decomposition of H2O2 for efficient NO oxidation.

The H2O2 evaporation rate directly affected the oxidation of NO by H2O2. Green zeolite and synthetic mordenite were selected to promote H2O2 thermal decomposition and NO oxidation. The effects of different zeolites, evaporation conditions, temperatures, and reactant concentrations on the NO oxidation ratio were explored. The promotion mechanism of zeolite on NO oxidation by H2O2 thermal decomposition was explained. The results show that the zeolite surface can significantly accelerate the H2O2 evaporation rate to obtain a high NO oxidation ratio. The hydrophilicity and rich pore structure of zeolite enable the rapid diffusion and evaporation of droplets on the zeolite surface. Compared with the green zeolite with the mesoporous structure, the synthetic mordenite with the hierarchical pore structure has a more obvious promotion effect on the NO oxidation by H2O2 thermal decomposition. The reason is that the synthetic mordenite contains micropores, resulting in a larger specific surface area, and the mesoporous structure is conducive to the mass transfer and diffusion of H2O2 on its surface. The product of NO oxidation is mainly NO2, which proves that ·OH plays a major role in the process.

Nitrogen atom coordination tuned transition metal catalysts for NO oxidation and reduction.

Developing an efficient catalyst for NO oxidation and reduction at ambient temperature is a significant challenge. Recent studies have suggested that the N-coordinated transition metal (TM) single atom catalysts (SACs) have high catalytic activity and stability. Herein, we report the activation potential of a series of 3d TM atoms supported on N coordination-tuned graphene (GR) for NO oxidation and reduction. The results show that the N coordination pattern can greatly alter the catalytic reactivity of TM on the catalysts, and the TM atom on the catalysts with three-coordinated pyridinic nitrogen TM-N3@GR exhibit the strongest chemical activity. Among the TM-N3@GR catalysts, Ti-N3@GR is the most promising candidate. The rate constants and equilibrium constants were calculated to evaluate the kinetic and thermodynamic feasibility of the catalytic reaction, respectively. Our results demonstrate that the reduction of NO to N2 on Ti-N3@GR can occur at ambient temperature with a large exotherm of 6.99 eV, and the oxidation of NO to NO2 on Ti-N3@GR can easily proceed when the temperature reaches 360 K with a large equilibrium constant. Our studies are of great significance for understanding the performance of N coordination-tuned catalysts and designing Ti-based catalysts for NO oxidation and reduction.

Surface Boronizing Can Weaken the Excitonic Effects of BiOBr Nanosheets for Efficient O2 Activation and Selective NO Oxidation under Visible Light Irradiation.

The photocatalytic O2 activation for pollutant removal highly depends on the controlled generation of desired reactive oxygen species (ROS). Herein, we demonstrate that the robust excitonic effect of BiOBr nanosheets, which is prototypical for singlet oxygen (1O2) production to partially oxidize NO into a more toxic intermediate NO2, can be weakened by surface boronizing via inducing a staggered band alignment from the surface to the bulk and simultaneously generating more surface oxygen vacancy (VO). The staggered band alignment destabilizes excitons and facilitates their dissociation into charge carriers, while surface VO traps electrons and efficiently activates O2 into a superoxide radical (•O2-) via a one-electron-transfer pathway. Different from 1O2, •O2- enables the complete oxidation of NO into nitrate with high selectivity that is more desirable for safe indoor NO remediation under visible light irradiation. This study provides a facile excitonic effect manipulating method for layered two-dimensional photocatalysts and sheds light on the importance of managing ROS production for efficient pollutant removal.

Insight into the mechanism of deep NO photo-oxidation by bismuth tantalate with oxygen vacancies.

Deeply photocatalytic oxidation of nitrogen oxides is still difficult to achieve, mainly limited by few intrinsic active sites and inefficient carrier separation of photocatalysts. Accordingly, we develop a simple room temperature tactic to introduce oxygen vacancies (OVs) into Bi3TaO7 (BTO). Based on solid experimental and DFT theoretical supports, we explore the mechanism of NO removal over OVs decorated BTO (OVs-BTO). OVs can not only alter the distribution of local electrons to result in the formation of a fast charge transfer channel between OVs and the adjacent Ta atoms, which improves the transport rate of photogenerated carriers; but also function as active sites to adsorb small molecules (NO, O2 and H2O), which being activated and positively drive the NO oxidation reaction. In order to investigate a possible reaction path, a combination of in-situ DRIFTS and simulated Gibbs free energy reveals that the intermediate products of OVs-BTO are helpful to promote the deep oxidation of NO to NO3-, while pristine BTO is more likely to produce NO2 intermediate toxic by-products, which greatly hinders the deep photocatalytic oxidation of NO. This work provides insights into the role of OVs in photocatalysts, and also points out a guideline for the mechanism of semiconductor photocatalysts in eliminating gaseous pollutants.