Self-supporting three-dimensional CuNi-Sb-SnO2 anode with ultra-long service life for efficient removal of antibiotics in wastewater.

Electrochemical ozone production (EOP) is a promising technology for the removal of contaminants in wastewater. However, traditional two-dimensional anodes for EOP are restricted by their reliance on substrates and limited surface area, thus exhibiting poor stability and efficiency. Herein, a novel three-dimensional Sb-SnO2 with Cu and Ni co-doped (3D CuNi-ATO) was synthesized via a facile pressing-sintering method without the Ti substrate. 3D CuNi-ATO had a specific surface area two orders of magnitude higher than conventional CuNi-ATO/Ti, as well as the significant capability of EOP that differs from intrinsic 3D ATO. This endowed 3D CuNi-ATO with the capability to remove tetracycline with a pseudo-first-order rate constant of 0.033 min-1 under a low current density of 5 mA cm-2 within 120 min, which was far more efficient than that by 3D ATO and other two-dimensional anodes reported. The 3D CuNi-ATO was confirmed stable in 100 cycles and had an accelerated service lifetime of over 1100 h versus 83 h of CuNi-ATO/Ti. The degradation of tetracycline in complex matrix and flow-through reactors further revealed the promising potential of 3D CuNi-ATO to be applied in scenarios of practical application and continuous high-rate treatment.

Green Synthesis of Au-Doped Tin Oxide Nanoparticles Using Teucrium Polium Extract with Potential Applications in Photodynamic Therapy.

Objective: The green synthesis of Tin(IV) oxide (SnO2): Gold (Au) nanoparticles (NPs) using Teucrium polium medicinal plant extract was investigated, and the NPs were characterized and tested as photosensitizers to produce reactive oxygen species (ROS). Methods: The cytotoxic effect on C26 cells was investigated using the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) technique. The results showed their toxicity in a dose-dependent manner. The green synthesis of SnO2:Au NPs was achieved for the first time using an extract of T. polium medicinal plant as a reducing and stabilizing agent. The produced NPs were examined for their application in photodynamic therapy (PDT) for cancer. Results: Methylene blue and anthracene were used to confirm that the photosensitizer could produce ROS when excited with UVA radiation. The anticancer activity of SnO2:Au was investigated in vitro using the C26 cell line and an MTT assay, showing that PDT with SnO2:Au NPs could inhibit cancer cell proliferation. Conclusions: The significant afterglow of the SnO2:Au NPs could cause the generation of ROS to continue several minutes after switching off the light source.

Cu2O-SnO2-PDA heterozygous nanozyme doped hydrogel mediated conglutinant microenvironment regulation for wound healing therapy.

Bacterial infection significantly hinders the wound healing process. Overuse of antibiotics has led to the rise of drug resistance in bacteria, making the development of smart medical dressings that promote wound healing without antibiotics, a critical need. In this study, Cu2O-SnO2-PDA (PCS) nanoenzymes with Fenton-like activity and high photothermal conversion efficiency were developed. These nanoenzymes were then incorporated into a hydrogel through cross-linking of acrylamide (AM) and N-[Tris-(hydroxymethyl)methyl] acrylamide (THMA), forming a tough, highly-adhesive, and self-healing composite hydrogel (AT/PCS) with antimicrobial properties. The AT/PCS hydrogel exhibits excellent mechanical strength and adhesion, facilitating increased oxygen levels and strong adherence to the wound site. Moreover, it effectively regulates the wound microenvironment by combining synergistic chemodynamic therapy (CDT) and photothermal therapy (PTT) for antibacterial treatment. The AT/PCS hydrogel enhances collagen deposition and expedites wound healing in a rat model, largely due to its potent antibacterial properties.

Solar light driven enhanced in photocatalytic activity of novel Gd incorporated ZnO/SnO2 heterogeneous nanocomposites.

The Gd-doped ZnO/SnO2 nanocomposites with various atomic percentages (0, 0.5, 0.8, and 1.2 at%) of gadolinium (coded as GdZS0, GdZS1, GdZS2, and GdZS3) was synthesis via the sol-gel method and explored for photodegradation against dye solutions exposing solar light irradiation. The synthesized nanocomposites were characterized employing the XRD, FTIR, FE-SEM, Raman spectroscopy, BET analysis and UV-Vis spectrophotometer. The FE-SEM results indicated that the formation of nanoparticles to nanoflowers covered with Gd ions was observed with an increased doping concentration of Gd. The optical bandgap was evaluated and found in the range of 3.21-3.27 eV for GdZS nanocomposites. The GdZS nano-photocatalysts were investigated against the degradation of different organic dyes and GdZS3 shows the highest degradation efficiencies of 99.3%, 98.3% and 99.4% towards MO, MB and RhB dyes, respectively at neutral pH in aqueous media. Before and after photodegradation. Biological oxygen demand and chemical oxygen demand tests to make estimations of mineralization. The investigations are very promising for the degradation process in rare earth doped metal oxide nanocomposites. A plausible photodegradation mechanism of synthesized nanocomposites under investigation has also been proposed.

Visible-light enhanced tetracycline degradation via SnO2/TiO2-Ni@rGO ternary heterostructures.

This study explores the synthesis, characterization, and photocatalytic performance of a SnO2/TiO2-Ni@rGO nanocomposite for tetracycline (TC) degradation under visible light irradiation. The nanocomposite was precisely designed to enhance structural stability, charge transfer efficiency, and catalytic activity. X-ray diffraction (XRD) analysis confirmed the structural integrity of the SnO2/TiO2-Ni@rGO composite, demonstrating excellent reusability and resistance to photo-corrosion after multiple cycles. Photocatalytic experiments revealed that the SnO2/TiO2-Ni@rGO nanocomposite significantly outperformed individual SnO2/TiO2-Ni and rGO catalysts, achieving a remarkable 94.6% degradation of TC within 60 min. The degradation process followed pseudo-first-order kinetics, with a rate constant (k) of 0.046 min-1. The Z-scheme charge transfer mechanism facilitated efficient separation and migration of photogenerated charge carriers, generating reactive oxygen species such as superoxide (•O2 -) and hydroxyl (•OH) radicals crucial for the oxidation of TC. Radical scavenger studies confirmed that superoxide and hydroxyl radicals were the primary active species. The SnO2/TiO2-Ni@rGO composite also exhibited excellent reusability, maintaining high catalytic performance over four consecutive cycles. These findings suggest that the SnO2/TiO2-Ni@rGO nanocomposite is a promising candidate for the efficient and sustainable photocatalytic degradation of persistent organic pollutants like TC, offering significant potential for environmental remediation applications.

Enhancing the Performance of Nanocrystalline SnO2 for Solar Cells through Photonic Curing Using Impedance Spectroscopy Analysis.

Wide-bandgap tin oxide (SnO2) thin-films are frequently used as an electron-transporting layers in perovskite solar cells due to their superior thermal and environmental stabilities. However, its crystallization by conventional thermal methods typically requires high temperatures and long periods of time. These post-processing conditions severely limit the choice of substrates and reduce the large-scale manufacturing capabilities. This work describes the intense-pulsed-light-induced crystallization of SnO2 thin-films using only 500 µs of exposure time. The thin-films' properties are investigated using both impedance spectroscopy and photoconductivity characteristic measurements. A Nyquist plot analysis establishes that the process parameters have a significant impact on the electronic and ionic behaviors of the SnO2 films. Most importantly, we demonstrate that light-induced crystallization yields improved topography and excellent electrical properties through enhanced charge transfer, improved interfacial morphology, and better ohmic contact compared to thermally annealed (TA) SnO2 films.

Electron-rich SnO2 promote CO2 activation for stable electrocatalytic CO2 reduction.

Electrocatalytic CO2 reduction reaction (CO2RR) to formate offers a promising route for carbon neutralization, but its reactivity is largely compromised due to the competitive hydrogen evolution reaction (HER) accompanying the activation of CO2 at high potentials. Herein, we modulated the charge density around Sn atoms by introducing La2Sn2O7 into SnO2, with the rich grain boundaries and fast electron transport of the heterostructure promoting CO2 reduction. Combined theoretical calculations and in situ electrochemical attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR) characterization revealed enhanced activation of CO2 and adsorption of *OCHO intermediates by the constructed electron-rich SnO2. During the CO2RR process over 5 % La2Sn2O7/SnO2 catalyst, the Sn oxidation state can be effectively stabilized by the oxygen vacancies and amorphous phases appearing around SnO2, with a FE of 70.7 % for HCOOH at -0.9 V vs. RHE and stable electrolysis of 39 h. This work provides an ideal approach for the development of highly stable Sn-based electrocatalysts.

Construction of trace nitric oxide sensors at low temperature based on bulk embedded BiVO4 in SnO2 nanofibers with nano-heterointerfaces.

Constructing heterostructures is an effective way to improve the carrier mobility for metal oxide sensing material, since heterojunctions are usually built only on the surface of the material, the carrier transport efficiency inside the material still needs to be improved. In this paper, BiVO4 nanocrystals (BVO NCs) with an average size of 1 nm generated by pulsed laser irradiation were embedded in situ at the particle boundaries (PBs) of SnO2 nanofibers to form an effective n-n heterojunctions inside the material. After embedding the BVO NCs in the SnO2 samples, the response value for 10 ppm NO was improved to 48.91, which was 2.5 times higher than that of pure SnO2 at near room temperature (50 °C). Meanwhile, the detection limit was lowered to 50 ppb with excellent long term stability. Detailed analysis and theoretical calculations demonstrated that the formation of abundant n-n heterojunctions not only promotes the electron-hole separation and the carrier mobility, but also reduces the conductivity and adsorption energy of the material, which significantly improves its sensing performance. This work demonstrates a new approach to modulate the gas-sensing performance of metal oxide semiconductors by generating heterostructure inside the bulk of the material.

SnO2-Based Interfacial Engineering towards Improved Perovskite Solar Cells.

Interfacial engineering is of great concern in photovoltaic devices. Metal halide perovskite solar cells (PSCs) have garnered much attention due to their impressive development in power conversion efficiencies (PCEs). Benefiting from high electron mobility and good energy-level alignment with perovskite, aqueous SnO2 as an electron transport layer has been widely used in n-i-p perovskite solar cells. However, the interfacial engineering of an aqueous SnO2 layer on PSCs is still an obscure and confusing process. Herein, we proposed the preparation of n-i-p perovskite solar cells with different concentrations of SnO2 as electron transport layers and achieved optimized PCE with an efficiency of 20.27%. I Interfacial engineering with regard to the SnO2 layer is investigated by observing the surface morphology, space charge-limited current (SCLC) with the use of an electron-only device, and time-resolved photoluminescence (TRPL) of perovskite films.

Ce Doping Effects on the Hydrogen Sensing Properties of Graphene/SnO2-Based Sensors.

The development of a sensor capable of selectively detecting hydrogen levels in the environment holds immense importance for ensuring the safer utilization of hydrogen energy. In this study, a hydrogen sensor made of Ce-doped single-layer graphene (SLG)/SnO2 composite material was fabricated using a hydrothermal method. The study examined the impact of varying Ce doping concentrations on the hydrogen sensing capabilities of the SLG/SnO2 matrix. The results show that the SLG/SnO2 hydrogen sensor doped with 2 mol% Ce demonstrated optimal performance at a humidity of 20%. It operated most efficiently at 250 °C, with a response of 2.49, representing a 25.75% improvement over the undoped sample. The response/recovery times were 0.46/3.92 s, which are 54.9% shorter than those of the undoped sample. The enhancement in hydrogen sensitivity stems from the synergistic effect of Ce and SLG, which facilitates the coexistence of n-n and p-n heterojunctions, thereby increasing carrier mobility and refining grain structure. Analysis via X-ray photoelectron spectroscopy (XPS) reveals that Ce increases the material's oxygen vacancy concentration, enhancing its hydrogen sensitivity. Ce-doped SLG/SnO2, with its robust hydrogen sensitivity, represents one of the leading candidates for future hydrogen gas sensors.

Influence of Bi3+ Doping on Electrochemical Properties of Ti/Sb-SnO2/PbO2 Electrode for Zinc Electrowinning.

Bi3+ doped Ti/Sb-SnO2/PbO2 electrode materials were fabricated by electrodeposition to improve their electrochemical performance in zinc electrowinning. The surface morphology, chemical composition, and hydrophilicity of the as-prepared electrodes were characterized using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and contact angle. An electrochemical measurement and an accelerated lifetime experiment were also conducted to investigate the electrocatalytic performance and stability of the electrodes. The results show that the Bi3+ modification electrode has an important effect on the coating morphology, the crystal structure, the surface hydrophilicity, the electrocatalytic activity, and the stability. The electrode prepared from the solution containing 2 mmol·L-1 Bi(NO3)3 (marked as the Ti/Sb-SnO2/2Bi-PbO2 electrode) exhibits the best hydrophilicity performance (θ = 21.6°) and the longest service life (1196 h). During the electrochemical characterization analysis, the Ti/Sb-SnO2/2Bi-PbO2 electrode showed the highest oxygen evolution activity, which can be attributed to it having the highest electroactive surface (qT* = 21.20 C·cm-2) and the best charge-transfer efficiency. The DFT calculation demonstrated that the doping of Bi3+ leads to a decrease in the OER reaction barrier and an increase in the DOS of the electrode, which further enhances the catalytic activity and the conductivity of the electrode. Moreover, the simulated zinc electrowinning experiment demonstrated that the Ti/Sb-SnO2/2Bi-PbO2 electrode consumes less energy than other electrodes. Therefore, it is expected that the Bi3+ modified electrode will become a very promising electrode material for zinc electrowinning in the future.

Uniform Nanocrystal Spatial Distribution-Enhanced SnO2-based Sensor for High-Sensitivity Hydrogen Detection.

Hydrogen (H2) is colorless, odorless, and has a wide explosive concentration range (4-75 vol %), making rapid and accurate detection of hydrogen leaks essential. This paper demonstrates a method to modify the spatial distribution of nanocrystals (NCs) by adding surfactants to improve the sensing performance. In order to explore its potential for H2 gas-sensing applications, SnO2, containing different mass percentages of PdCu NCs, was dispersed. The results show that the 0.1 wt % PdCu-SnO2 sensor based on surfactant dispersion performs well, with a response to 0.1 vol % H2 that is 18 times higher than that of the undispersed 0.1 wt % PdCu-SnO2 sensor. The enhanced gas-sensing ability after dispersion can be attributed to the fact that the uniform distribution of NCs generates higher quantum efficiency and exposes more active sites on the carrier surface compared to nonuniform distribution. This study provides a simple, novel, and effective method to improve the sensor response.

Wearable Inorganic Oxide Chemiresistor Based on Flexible Al2O3-Stabilized ZrO2 Ceramic Sponge Substrate for NO2 Sensing.

Wearable gas sensors, possessing the advantages of high sensitivity, excellent flexibility, high permeability, low weight, and workability at ambient conditions, hold great promise for real-time health monitoring and early warnings of poisonous gases. However, obtaining high-performance wearable gas sensors utilizing the current well-developed inorganic semiconductor oxide sensing materials is still very limited due to their fragile and rigid nature. Herein, a newly designed wearable gas sensor based on an all-inorganic ASZ (Al2O3-stabilized ZrO2)/ZnO/SnO2 nanofibers is introduced for the first time. The flexible ASZ ceramic sponge substrate (with a Young's modulus of 4.15 MPa) and ultrathin ZnO/SnO2 sensing layer endow the wearable gas sensor with promising properties such as super flexibility (with a bending radius of 5 mm), high gas permeability, and low weight. Furthermore, driven by UV light irradiation, this all-inorganic wearable sensor also demonstrates a stable NO2 sensing response under different bending states at room temperature, which enables the gas sensor to be more compatible with wearable sensing applications. This work offers a general method to achieve a high-performance wearable gas sensor based on inorganic materials and provides new insights into their potential in wearable gas-sensing applications.

An Efficient MnO2 Photocathode with an Excellent SnO2 Electron Transport Layer for Photo-Accelerated Zinc Ion Batteries.

Photo-accelerated rechargeable batteries play a crucial role in fully utilizing solar energy, but it is still a challenge to fabricate dual-functional photoelectrodes with simultaneous high solar energy harvesting and storage. This work reports an innovative photo-accelerated zinc-ion battery (PAZIB) featuring a photocathode with a SnO2@MnO2 heterojunction. The design ingeniously combines the excellent electronic conductivity of SnO2 with the high energy storage and light absorption capacities of MnO2. The capacity of the SnO2@MnO2-based PAZIB is ≈598 mAh g-1 with a high photo-conversion efficiency of 1.2% under illumination at 0.1 A g-1, which is superior to that of most reported MnO2-based ZIB. The boosting performance is attributed to the synergistic effect of enhanced photogenerated carrier separation efficiency, improved conductivity, and promoted charge transfer by the SnO2@MnO2 heterojunction, which is confirmed by systematic experiments and theoretical simulations. This work provides valuable insights into the development of dual-function photocathodes for effective solar energy utilization.

Bottom Contact Engineering for Ambient Fabrication of >25% Durable Perovskite Solar Cells.

The bottom contact in perovskite solar cells (PSCs) is easy to cause deep trap states and severe instability issues, especially under maximum power point tracking (MPPT). In this study, sodium gluconate (SG) is employed to disperse tin oxide (SnO2) nanoparticles (NPs) and regulate the interface contact at the buried interface. The SG-SnO2 electron transfer layer (ETL) enabled the deposition of pinhole-free perovskite films in ambient air and improved interface contact by bridging effect. SG-SnO2 PSCs achieved an impressive power conversion efficiency (PCE) of 25.34% (certified as 25.17%) with a high open-circuit voltage (VOC) exceeding 1.19 V. The VOC loss is less than 0.34 V relative to the 1.53 eV bandgap, and the fill factor (FF) loss is only 2.02% due to the improved contact. The SG-SnO2 PSCs retained around 90% of their initial PCEs after 1000 h operation (T90 = 1000 h), higher than T80 = 1000 h for the control SnO2 PSC. Microstructure analysis revealed that light-induced degradation primarily occurred at the buried holes and grain boundaries and highlighted the importance of bottom-contact engineering.

Electrohydrodynamic-Jet-Printed SnO2-TiO2-Composite-Based Microelectromechanical Systems Sensor with Enhanced Ethanol Detection.

Ethanol sensors have found extensive applications across various industries, including the chemical, environmental, transportation, and healthcare sectors. With increasing demands for enhanced performance and reduced energy consumption, there is a growing need for developing new ethanol sensors. Micro-electromechanical system (MEMS) devices offer promising prospects in gas sensor applications due to their compact size, low power requirements, and seamless integration capabilities. In this study, SnO2-TiO2 nanocomposites with varying molar ratios of SnO2 and TiO2 were synthesized via ball milling and then printed on MEMS chips for ethanol sensing using electrohydrodynamic (EHD) printing. The study indicates that the two metal oxides dispersed evenly, resulting in a well-formed gas-sensitive film. The SnO2-TiO2 composite exhibits the best performance at a molar ratio of 1:1, with a response value of 25.6 to 50 ppm ethanol at 288 °C. This value is 7.2 times and 1.8 times higher than that of single SnO2 and TiO2 gas sensors, respectively. The enhanced gas sensitivity can be attributed to the increased surface reactive oxygen species and optimized material resistance resulting from the chemical and electronic effects of the composite.

Experimental and Density Functional Theory Simulation Research on PdO-SnO2 Nanosheet Ethanol Gas Sensors.

Pure SnO2 and 1 at.% PdO-SnO2 materials were prepared using a simple hydrothermal method. The micromorphology and element valence state of the material were characterized using XRD, SEM, TEM, and XPS methods. The SEM results showed that the prepared material had a two-dimensional nanosheet morphology, and the formation of PdO and SnO2 heterostructures was validated through TEM. Due to the influence of the heterojunction, in the XPS test, the energy spectrum peaks of Sn and O in PdO-SnO2 were shifted by 0.2 eV compared with SnO2. The PdO-SnO2 sensor showed improved ethanol sensing performance compared to the pure SnO2 sensor, since it benefited from the large specific surface area of the nanosheet structure, the modulation effect of the PdO-SnO2 heterojunction on resistance, and the catalyst effect of PdO on the adsorption of oxygen. A DFT calculation study of the ethanol adsorption characteristics of the PdO-SnO2 surface was conducted to provide a detailed explanation of the gas-sensing mechanism. PdO was found to improve the reducibility of ethanol, enhance the adsorption of ethanol's methyl group, and increase the number of adsorption sites. A synergistic effect based on the continuous adsorption sites was also deduced.

NO2-Sensitive SnO2 Nanoparticles Prepared Using a Freeze-Drying Method.

The n-type semiconductor SnO2 with a wide band gap (3.6 eV) is massively used in gas-sensitive materials, but pure SnO2 still suffers from a high operating temperature, low response, and tardy responding speed. To solve these problems, we prepared small-sized pure SnO2 using hydrothermal and freeze-drying methods (SnO2-FD) and compared it with SnO2 prepared using a normal drying method (SnO2-AD). The sensor of SnO2-FD had an ultra-high sensitivity to NO2 at 100 °C with excellent selectivity and humidity stability. The outstanding gas sensing properties are attributed to the modulation of energy band structure and the increased carrier concentration, making it more accessible for electron exchange with NO2. The excellent gas sensing properties of SnO2-FD indicate its tremendous potential as a NO2 sensor.

Macroporous Structures of Nb-SnO2 Particles as a Catalyst Support Induce High Porosity and Performance in Polymer Electrolyte Fuel Cell Catalyst Layers.

Macroporous niobium-doped tin oxide (NTO) is introduced as a robust alternative to conventional carbon-based catalyst supports to improve the durability and performance of polymer electrolyte fuel cells (PEFCs). Metal oxides like NTO are more stable than carbon under PEFC operational conditions, but they can compromise gas diffusion and water management because of their denser structures. To address this tradeoff, we synthesized macroporous NTO particles using a flame-assisted spray-drying technique employing poly(methyl methacrylate) as a templating agent. X-ray diffraction analysis and scanning electron microscopy confirmed the preservation of crystallinity and revealed a macroporous morphology with larger pore volumes and diameters than those in flame-made NTO nanoparticles, as revealed by mercury porosimetry. The macroporous NTO particles exhibited enhanced maximum current density and reduced gas diffusion resistance relative to commercial carbon supports. Our findings establish a foundation for integrating macroporous NTO structures into PEFCs to optimize durability and performance.

Enhancing the Efficiency and Stability of Perovskite Solar Cells Using Chemical Bath Deposition of SnO2 Electron Transport Layers and 3D/2D Heterojunctions.

Chemical bath deposition (CBD) is an effective technique used to produce high-quality SnO2 electron transport layers (ETLs) employed in perovskite solar cells (PSCs). By optimizing the CBD process, high-quality SnO2 films are obtained with minimal oxygen vacancies and close energy level alignment with the perovskite layer. In addition, the 3D perovskite layers are passivated with n-butylammonium iodide (BAI), iso-pentylammonium iodide (PNAI), or 2-methoxyethylammonium iodide (MOAI) to form 3D/2D heterojunctions, resulting in defect passivation, suppressing ion migration and improving charge carrier extraction. As a result of these heterojunctions, the power conversion efficiency (PCE) of the PSCs increased from 21.39% for the reference device to 23.70% for the device containing the MOAI-passivated film. The 2D perovskite layer also provides a hydrophobic barrier, thus enhancing stability to humidity. Notably, the PNAI-based device exhibited remarkable stability, retaining approximately 95% of its initial efficiency after undergoing 1000-h testing in an N2 environment at room temperature.