Structural Design and Performance of Cut-Resistant Fabrics with Concave-Convex Arrays.

As the risk of social security increases, it is crucial to develop flexible protective materials that combine flexibility with high protective performance. Ultra-high-molecular-weight polyethylene (UHMWPE) was selected as the raw material, and four types of flat-knitting cut-resistant fabrics were ultimately designed and prepared from a three-dimensional longitudinal dimension and concave-convex array structure based on rib knitting. A series of experiments must be conducted on fabrics in order to study the law of protection performance of different structural fabrics. They were thus subjected to comprehensive evaluation and theoretical analysis of cut resistance. The results demonstrate that the four structural fabrics exhibited resilience in abrasion tests, withstanding over 100,000 cycles without failure. A weighting algorithm was employed to determine the comprehensive cutting resistance of the S1, S2, S3, and S4 structural fabrics, resulting in values of 1939.9 gf, 2298.6 gf, 2577.1 gf, and 2822.2 gf, respectively. Therefore, S1 reached class A4, which is sufficient to address a medium cut hazard. Similarly, S2, S3, and S4 reached class A5, which is adequate to address a high cut hazard. The obtained fitting equation, with uniform yarn fineness T as the dependent variable, demonstrates that the cut resistance improved as the concave-convex density level increased.

Evaluation of microhardness, degree of conversion, and abrasion resistance of nanoglass and multiwalled carbon nanotubes reinforced three-dimensionally printed denture base resins.

PURPOSE: To assess the effect of nanoglass (NG) particles and multiwalled carbon nanotubes' (MWCNTs) addition on Vickers hardness (VH), degree of conversion (DC), and abrasion resistance of 3D-printed denture base resin. MATERIALS AND METHODS: 3D-printed denture base resin was reinforced using silanized NG and MWCNTs to obtain four groups: Control, 0.25 wt% NG reinforced resin, 0.25 wt% MWCNTs reinforced resin, and a combination group of 0.25 wt% of both fillers. All specimens (N = 176) were tested before and after thermal aging (600 cycles) for VH (n = 22), DC, and abrasion resistance (n = 22). Abrasion resistance specimens were subjected to 60,000 brushing strokes, and then assessed for surface roughness (Ra) and weight loss. Specimens were then scanned with a benchtop scanner before and after abrasion to produce a color map of topographical changes from superimposed images. Data were analyzed using ANOVA tests followed by Tukey post hoc test. Kruskal-Wallis test was used to compare percent change among groups, followed by Dunn post hoc test (α = 0.05). RESULTS: The interaction between nanofiller content and thermal cycling displayed a significant effect on VH and DC. The 0.25% NG expressed the highest VH before aging but revealed the highest percent decrease after aging. Nanofiller content, thermal aging, and brushing displayed a significant interaction impact on the Ra values. CONCLUSIONS: The addition of nanofillers resulted in an overall improvement in resin microhardness and abrasion resistance. The 0.25% MWCNTs group revealed the lowest Ra with the least percent change in VH and DC, while the combination one displayed the least change in weight.

Effect of nano-TiO2 size and utilization ratio on the performance of photocatalytic concretes; self-cleaning, fresh, and hardened state properties.

In this study, photocatalysis technology was used to reduce water pollution. Decolorization of Reactive Black 5 using nano-TiO2 (NT) as a photocatalyst was investigated by adsorption and degradation experiments. Effects of NT particle size and utilization ratio on the time-dependent flow performance, compressive-flexural strength, and Bohme abrasion resistance of cementitious systems were investigated. In addition to the NT-free control mixture, a total of six photocatalytic self-cleaning mortar mixtures (PSCM) were prepared using NT in two different particle sizes (28 and 38 nm) and three different ratios (0.5%, 1%, and 1.5%). The PSCM sample containing 38 nm NT exhibited superior performance in terms of photocatalytic properties compared to the 28 nm state. It was observed that the flow performance of PSCM mixtures with NT substitution is adversely affected regardless of the NT type. Mixtures containing NT with a lower particle size (28 nm) had higher compressive and flexural strengths.

Preparation of Ceramic Fiber Threads with Enhanced Abrasion Resistance Performance.

Ceramic fiber thread is one of the key components in flexible external thermal insulation blankets, and it has been applied in various fields as a flexible ceramic fibrous material with excellent deformability and high-temperature resistance. However, ceramic fiber threads are often subjected to reciprocating friction motion at specific bending angles, making them highly susceptible to abrade and fracture. Enhancing the abrasion resistance performance of ceramic fiber threads under bending conditions is the future trend and remains a significant challenge. Hence, we design and construct a novel polyurethane-modified coating on the ceramic fiber threads to improve their abrasion resistance performance. The effects of the types and concentrations of modifiers on the microstructure, abrasion resistance property, and tensile property of ceramic fiber threads are systematically investigated. The ceramic fiber threads, after modification with hexamethylene diisocyanate waterborne polyurethane (HDI-WPU) with a concentration of 3%, exhibit excellent abrasion resistance properties. The number of friction cycles at fracture of the modified ceramic fiber thread is more than three times, and the tensile strength is more than one and a half times, that of the original ceramic fiber thread, demonstrating the great potential of the HDI-WPU modifier for enhancing the abrasion resistance performance of ceramic fiber threads.

Mechanical Resistance of the Largest Denticle on the Movable Claw of the Mud Crab.

Decapod crustaceans have tooth-like white denticles that are present only on the pinching side of the claws. In the mud crab, Scylla serrata, a huge denticle exists on the movable finger of the dominant claw. This is mainly used to crush the shells of the crab's staple food. The local mechanical properties, hardness (HIT) and elastic modulus (Er), of the peak and valley areas of the largest denticle were examined via a nanoindentation test. The microstructure and elemental composition were characterized using a scanning electron microscope and energy-dispersive X-ray spectroscopy. The striation patterns originating from a twisted plywood structure parallel to the surface were visible over the entire denticle. Most of the largest denticle was occupied by a hard area without phosphorus, and there was a soft layer corresponding to the endocuticle with phosphorus in the innermost part. The HIT of the denticle valley was about 40% lower than that of the denticle peak, and the thickness of the soft endocuticle of the denticle valley was five times thicker than that of the denticle peak. The HIT-Er map showed that the abrasion resistance of the denticle surface was vastly superior and was in the top class among organisms. The claw denticles were designed with the necessary characteristics in the necessary places, as related to the ecology of the mud crab.

Effect of Polyoxymethylene Fiber on the Mechanical Properties and Abrasion Resistance of Ultra-High-Performance Concrete.

It is necessary to prepare marine UHPC with synthetic fibers instead of steel fibers, owing to the corrosion risk of steel fibers in marine environments. Currently, the performance of UHPC prepared with different types of fibers has not been comparatively investigated. This work prepared UHPC with steel fiber, polyoxymethylene (POM) fiber, polypropylene (PP) fiber, and polyvinyl alcohol (PVA) fiber. The effects of different fibers on the mechanical properties, impact, and abrasion resistance of UHPC were studied and compared. The results showed that increasing POM fiber can increase the mechanical strength, flexural toughness, impact, and abrasion resistance of UHPC. When its content reaches 2%, the adsorbed-in-fracture energy and abrasion strength of UHPC are 2670 J and 105 h/(kg/m2), respectively. At the same fiber content, POM fiber-reinforced UHPC shows better mechanical strength, toughness, and impact- and abrasion-resistance than the polypropylene (PP)- and polyvinyl alcohol (PVA)-fiber-reinforced UHPCs. Microstructure investigation found that PP fiber has the weakest binding with UHPC paste, which would directly pull out of the matrix under external tensile loading. This weak connection limits the strengthening and toughening effect on the UHPC. PVA fiber has an excellent interfacial connection with the UHPC paste. However, the low tensile strength of PVA fiber limits the strength and toughness of UHPC. POM fiber has a high tensile strength and can absorb tensile loading through debonding, fracture, and tearing. The fracture interface of POM fiber is large, indicating its significant role in strengthening and toughening the UHPC.

Modified polyamide fibers with low surface friction coefficient to reduce microplastics emission during domestic laundry.

The widespread presence of microplastics has become a serious threat to humans and ecological environments because they carry many pollutants and can be easily ingested by aquatic organisms. Fibrous microplastics (FMPs) released from synthetic fiber garments during domestic laundry are a major source of contamination. Herein, we report a facile FMPs mitigation strategy for polyamide 6 (PA6) fibers by incorporating environmentally friendly polydimethylsiloxane (PDMS) during melt spinning. The obtained PA6/PDMS fibers showed a lower friction coefficient than the pure PA6 fibers. Surface morphology, tribology, and washing characterizations verified that a 60% reduction in FMPs shedding was achieved by reducing the friction. In addition, the low-surface-friction PA6/PDMS fabrics with high hydrophobicity exhibited improved waterproof and anti-stain behaviors. It is important to note that none of the essential properties, such as surface structure, dyeing and printing of the fabrics were compromised after PDMS blending. This study provides a green and scalable route for mitigating laundry microfibers using a fiber domain design.

Freeze-thaw cycle and abrasion resistance of alkali-activated FA and POFA-based mortars: Role of high volume GBFS incorporation.

Alkali-activated binders made from various waste products can appreciably reduce the emission of CO2 and enhance the waste recycling efficiency, thus making them viable substitutes to ordinary Portland cement (OPC)-based binders. Waste materials including fly ash (FA), palm oil fuel ash (POFA), and granulated blast furnace slag (GBFS) reveal favorable effects when applied to alkali-activated mortars (AAMs) that are mainly related to the high contents of silica, alumina, and calcium. Therefore, fifteen AAM mixes enclosing FA, POFA with high volume of GBFS were designed. The obtained GBFS/FA/POFA-based AAMs were subjected wet/dry and freeze/thaw cycles. The impact of various GBFS contents on the microstructures, freeze-thaw cycle, abrasion resistance, mechanical and durability features of the proposed AAMs were evaluated. The results showed that presence of Ca can significantly affect the AAMs durability features and long-term performance. The abrasion resistance of the AAMs was decreased with the decrease of CaO contents. Furthermore, the abrasion depth of 70% AAMs (0.8 mm) was lower in comparison to the mix made by replacing 50 wt% of FA with GBFS (1.4 mm). Generally, increase in the GBFS contents from 50 to 70% could largely impact the AAMs properties under aggressive environmental exposure. The expansion and physical impacts during the freezing-thawing cycles was argued to destroy the bonds in C-S-H and paste-aggregates, causing the formation of large cracks. It is asserted that the AAM mixes made from FA, POFA and high volume of GBFS may offer definitive mechanical, durable, and environmental benefits with their enhanced performance under aggressive environments.

Multifunctional Biomimetic Composite Coating with Antireflection, Self-Cleaning and Mechanical Stability.

Antireflective and self-cleaning coatings have attracted increasing attention in the last few years due to their promising and wider applications such as stealth, display devices, sensing, and other fields. However, existing antireflective and self-cleaning functional material are facing problems such as difficult performance optimization, poor mechanical stability, and poor environmental adaptability. Limitations in design strategies have severely restricted coatings' further development and application. Fabrication of high-performance antireflection and self-cleaning coatings with satisfactory mechanical stability remain a key challenge. Inspired by the self-cleaning performance of nano-/micro-composite structure on natural lotus leaves, SiO2/PDMS/matte polyurethane biomimetic composite coating (BCC) was prepared by nano-polymerization spraying technology. The BCC reduced the average reflectivity of the aluminum alloy substrate surface from 60% to 10%, and the water contact angle (CA) was 156.32 ± 0.58°, illustrating the antireflective and self-cleaning performance of the surface was significantly improved. At the same time, the coating was able to withstand 44 abrasion tests, 230 tape stripping tests, and 210 scraping tests. After the test, the coating still showed satisfactory antireflective and self-cleaning properties, indicating its remarkable mechanical stability. In addition, the coating also displayed excellent acid resistance, which has important value in aerospace, optoelectronics, industrial anti-corrosion, etc.

Mechanical Resistance and Tissue Structure of Claw Denticles of Various Sizes in the Mud Crab, Scylla serrata.

Decapod crustaceans have tooth-like denticles on their claw fingers, which come into direct contact with predators and prey. Since the denticles are subject to more frequent and intense stress than other parts of the exoskeleton, they must be especially resistant to wear and abrasion. We clarified the mechanical resistance and tissue structure of the denticles arranged in a line on the fixed finger of the mud crab, which has huge claws. The denticles of the mud crab are small at the fingertip and become larger closer to the palm. The denticles have a twisted-plywood-pattern structure stacked parallel to the surface regardless of size, but the abrasion resistance strongly depends on the size of the denticles. Due to the dense tissue structure and calcification, the abrasion resistance increases as the denticle size increases, reaching its maximum at the denticle surface. The denticles of the mud crab have a tissue structure that prevents them from breaking when pinched. The high abrasion resistance of the large denticle surface is an essential feature for the frequent crushing of shellfish, which is the mud crab's staple food. The characteristics and tissue structure of the claw denticles on the mud crab may provide ideas for developing stronger, tougher materials.

Justification of Starching Cotton and Aramid Yarns by Industrial and Laboratory Processes.

The development and application of new types of fibres and their wider application influence the continuous invention of a more economical starching process, as one of the most expensive stages in the technological process of woven fabric production. For example, aramid fibres are increasingly used in clothing with effective protection from mechanical, thermal and abrasion exposure. Simultaneously, comfort and regulation of metabolic heat are extremely important, and this is achieved by using cotton woven fabrics. For such a woven fabrics to satisfy the protective properties and the possibility of all-day wear, fibre is needed, and thus a yarn, that will enable the efficient production of fine, light and comfortable protective woven fabrics. This paper investigates the influence of starching on the mechanical properties of aramid yarns and their comparison to cotton yarns of the same fineness. This will lead to knowledge about the efficiency and necessity of aramid yarn starching. The tests were carried out on an industrial and laboratory starching machine. According to the obtained results, the necessity and the improvement of the physical-mechanical properties of cotton and aramid yarns can be determined, both by industrial and laboratory starching. Finer yarn starched by the laboratory starching process achieves greater efficiency in the yarn's strength and resistance to wear, which indicates the need for starching aramid yarns, especially fineness 16.6 × 2 tex, but also finer ones.

Resistance to Abrasive Wear with Regards to Mechanical Properties Using Low-Alloy Cast Steels Examined with the Use of a Dry Sand/Rubber Wheel Tester.

This paper focuses on relationship between the mechanical properties and abrasive wear resistance, expressed by the Kb index, using an example of low-alloy cast steels. In order to achieve the aim of this work, eight cast steels of varying chemical composition were designed, cast and then heat treated. The heat treatment involved quenching and tempering at 200, 400 and 600 °C. Structural changes caused by tempering are demonstrated by the different morphologies of the carbide phases in the ferritic matrix. In the first part of this paper, the present state of knowledge about the influence of structure and hardness on the tribological properties of steels is discussed. This research involved the evaluation of a material's structure, as well as its tribological and mechanical properties. Microstructural observations were performed using a light microscope and a scanning electron microscope. Next, tribological tests were carried-out with the use of a dry sand/rubber wheel tester. To determine the mechanical properties, Brinell hardness measurements and a static tensile test were carried out. The relationship between the determined mechanical properties and abrasive wear resistance was then investigated. The analyses also provided information regarding the heat treatment states of the analyzed material in the as-cast and as-quenched states. It was found that the abrasive wear resistance, expressed by the index Kb, was most strongly correlated with hardness and yield point. In addition, observations of the wear surfaces indicated that the main wear mechanisms were microcutting and microplowing.

Recent Advances on the Abrasion Resistance Enhancements and Applications of Superhydrophobic Materials.

Researches on superhydrophobicity have been overwhelming and have shown great advantages in various fields. However, the abrasion resistance of superhydrophobic structures was usually poor, and they were easily damaged by external force or harsh environment, which greatly limited the applications of superhydrophobic surfaces. Much attention has been paid to improving the abrasion resistance of superhydrophobic materials by researchers. In this review, aimed at the advances on improving the abrasion resistance of superhydrophobic surfaces, it was summarized and compared three enhancement strategies including the reasonably design of micro-nano structures, the adoption of adhesives, and the preparation of self-healing surface. Finally, the applications of typical superhydrophobic materials with abrasion resistance were reviewed in various fields. In order to broaden the application fields of superhydrophobic materials, the abarasion resistance should be further improved. Therefore, we proposed the ideas for the future development of superhydrophobic materials with higher abrasion resistance. We hope that this review will provide a new approach to the preparation and development of stable superhydrophobic surfaces with higher abrasion resistance.

Synergistic Effect of Partial Replacement of Carbon Black by Palm Kernel Shell Biochar in Carboxylated Nitrile Butadiene Rubber Composites.

With the rapid development of the palm oil-related industry, this has resulted in the high production of palm oil waste. The increasing amount of palm oil waste has become an alarming issue in which researchers have carried out studies that this palm oil waste has the potential to be used as a biomass source. Carbon black (CB) is the most preferred reinforcing filler in the rubber industry but it has a disadvantage where CB is carcinogenic and a petroleum-based product. Hence CB is less sustainable. Palm kernel shell (PKS) derived from palm oil waste can be turned into palm kernel shell biochar (PKSBc) which can potentially be a value-added, sustainable biofiller as reinforcement in rubber composites. In this study, PKSBc is hybridized with CB (N660) at different loading ratios to be filled in carboxylated nitrile butadiene rubber (XNBR). This study aims to elucidate the effect of the varying ratios of hybrid CB/PKSBc on the rheological properties, abrasion resistance, and hardness of XNBR composites. In this study, both CB and PKSBc are incorporated into XNBR and were then cured with sulphur. The composites were prepared by using a two-roll mill. Different compositions of hybrid CB/PKSBc were incorporated. The rheological properties and physicomechanical properties, such as abrasion resistance and hardness of the vulcanizates, were investigated. Based on the results, as the loading ratio of PKSBc in hybrid CB/PKSBc increases, the cure time decreases, and the cure rate index increases. The abrasion resistance and hardness values of vulcanizates were maintained by the high loading of PKSBc which was due to the porous structure of PKSBc as shown in the morphological analysis of PKSBc. The pores of PKSBc provided mechanical interlocking to reduce volume loss and maintain the hardness of vulcanizates when subjected to force. With this, PKSBc is proven to be a semi-reinforcing filler that could not only act as a co-filler to existing commercialized CB, but PKSBc could also fully substitute CB as reinforcement in rubber, specifically XNBR as it is able to provide high abrasion resistance and hardness to the rubber composites. This would mean the performance of PKSBc is comparable with CB (N660) when it comes to maintaining the physicomechanical properties of XNBR composites in terms of abrasion resistance and hardness. Therefore, this approach of using eco-friendly filler derived from palm oil agricultural waste (PKSBc) can reduce the abundance of palm oil waste, be a sustainable alternative to act as a co-filler in hybrid CB/PKSBc to decrease the usage of CB, and helps to enhance the quality of existing rubber-based products.

Scheffe's Simplex Optimization of Flexural Strength of Quarry Dust and Sawdust Ash Pervious Concrete for Sustainable Pavement Construction.

Pervious concrete provides a tailored surface course with high permeability properties which permit the easy flow of water through a larger interconnected porous structure to prevent flooding hazards. This paper reports the modeling of the flexural properties of quarry dust (QD) and sawdust ash (SDA) blended green pervious concrete for sustainable road pavement construction using Scheffe's (5,2) optimization approach. The simplex mixture design method was adapted to formulate the mixture proportion to eliminate the set-backs encountered in empirical or trials and the error design approach, which consume more time and resources to design with experimental runs required to evaluate the response function. For the laboratory evaluation exercise, a maximum flexural strength of 3.703 N/mm2 was obtained with a mix proportion of 0.435:0.95:0.1:1.55:0.05 for water, cement, QD, coarse aggregate and SDA, respectively. Moreover, the minimal flexural strength response of 2.504 N/mm2 was obtained with a mix ratio of 0.6:0.75:0.3:4.1:0.25 for water, cement, QD, coarse aggregate and SDA, respectively. The test of the appropriateness of the developed model was statistically verified using the Student' t-test and an analysis of variance (ANOVA), and was confirmed to be acceptable based on computational outcomes at the 95% confidence interval. Furthermore, the scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) were used to evaluate the morphological and mineralogical behavior of green prior concrete samples with various additive mixture compositions. The addition of QD and SDA, on the other hand, aided the creation of porous microstructures in the concrete matrix due to fabric changes in the concrete mixture, potentially aided by the formation of cementitious compounds such as calcium aluminate hydrate and calcium silicate hydrate.

Fabrication of robust superhydrophobic magnetic multifunctional coatings and liquid marbles.

To obtain durable and multi-function superhydrophobic surfaces, we reported a facial method to prepare a multifunctional suspension (γ-Fe2O3@SiO2@PDMS suspension) named as FSP suspension, in which γ-Fe2O3 was coated by the silica shell and PDMS was used as the outer layer. Superhydrophobic magnetic polyurethane (SMPU) sponge was prepared by immersing the polyurethane (PU) sponge into the FSP suspension, exhibiting the superior ability to absorb oil. In addition, it could also move directionally by the attraction of magnets and absorb the oil along the fixed path. The heated superhydrophobic magnetic stainless steel (H-SMSS) mesh was acquired by spraying FSP suspension onto the stainless steel mesh and then heating at 400 °C, which demonstrated superior superhydrophobicity and resistance to abrasion and chemical corrosion. Besides, the H-SMSS mesh displayed excellent flux and efficiency to separate the oil/water mixture. Rolling droplets on FSP particles, the superhydrophobic magnetic liquid marbles (SMLMs) were fabricated, in which liquids with different volumes were encapsulated and transported directionally. Further, it was convenient to inject liquid into the SMLM and withdraw liquid from it. Thus, the prepared FSP suspension has promising applications in constructing large-area, robust, and multifunctional surfaces and microreactors.

Enhancement of Impact Abrasion Resistance Performances of White Cast Iron Utilizing Ti3AlC2.

Al-Ti-C master alloy agent is currently the most promising grain refiner. This work investigates the influence of Ti3AlC2 addition (1.0-3.0 wt.%) on the microstructure of a hypoeutectic cast iron (4.7 wt.% Cr, 2.3 wt.% C). Microstructures of the samples were examined by SEM (scanning electron microscope). It was demonstrated that the added Ti3AlC2 did reduce the size of coarse primary carbides. The XRD (X-ray diffraction) pattern shows that Ti3AlC2 is decomposed into TiC in the alloy substrate. The EDS (energy dispersive spectrometer) interfacial element analysis shows that TiC combines well with the matrix interface. As the Ti3AlC2 amount was increased, the finest microstructure was achieved. When 2 wt.% Ti3AlC2 was added, the wear-resistance property of the material improved and became two times harder than the former. However, when 3% Ti3AlC2 was added, TiC gathered at the crystal boundary, which caused a decrease in the wear resistance of the material.

Antibacterial properties and abrasion-stability: Development of a novel silver-compound material for orthodontic bracket application.

PURPOSE: Bacteria-induced white spot lesions are a common side effect of modern orthodontic treatment. Therefore, there is a need for novel orthodontic bracket materials with antibacterial properties that also resist long-term abrasion. The aim of this study was to investigate the abrasion-stable antibacterial properties of a newly developed, thoroughly silver-infiltrated material for orthodontic bracket application in an in situ experiment. METHODS: To generate the novel material, silver was vacuum-infiltrated into a sintered porous tungsten matrix. A tooth brushing simulation machine was used to perform abrasion equal to 2 years of tooth brushing. The material was characterized by energy dispersive X­ray (EDX) analysis and roughness measurement. To test for antibacterial properties in situ, individual occlusal splints equipped with specimens were worn intraorally by 12 periodontal healthy patients for 48 h. After fluorescence staining, the quantitative biofilm volume and live/dead distribution of the initial biofilm formation were analyzed by confocal laser scanning microscopy (CLSM). RESULTS: Silver was infiltrated homogeneously throughout the tungsten matrix. Toothbrush abrasion only slightly reduced the material's thickness similar to conventional stainless steel bracket material and did not alter surface roughness. The new silver-modified material showed significantly reduced biofilm accumulation in situ. The effect was maintained even after abrasion. CONCLUSION: A promising, novel silver-infiltrated abrasion-stable material for use as orthodontic brackets, which also exhibit strong antibacterial properties on in situ grown oral biofilms, was developed. The strong antibacterial properties were maintained even after surface abrasion simulated with long-term toothbrushing.

Durability Study of Thermal Transfer Printed Textile Electrodes for Wearable Electronic Applications.

Textile-based electronics hold great promise because they can endow wearable devices with soft and comfortable characteristics. However, the inherent porosity and fluffiness of fabrics result in high surface roughness, which presents great challenges in the manufacture of high-performance fabric electrodes. In this work, we propose a thermal transfer printing method to address the above challenges, in which electrodes or circuits of silver flake/thermoplastic polyurethane (TPU) composites are prefabricated on a release film by coating and laser engraving and then laminated by hot-pressing to a variety of fabrics and textiles. This universal and scalable production technique enables fabric electrodes to be made without compromising the original wearability, washability, and stretchability of textiles. The prepared fabric electrodes exhibit high conductivity (5.48 × 104 S/cm), high adhesion (≥1750 N/m), good abrasion/washing resistance, high patterning resolution (∼40 µm), and good electromechanical performance up to 50% strain. To demonstrate the potential applications, we developed textile-based radio frequency identification (RFID) tags for remote identification and a large-sized heater for wearable thermotherapy. More importantly, the solvent-free thermal transfer printing technology developed in this paper enables people to DIY interesting flexible electronics on clothes with daily tools, which can promote the commercial application of smart textile-based electronics.

Mechanism and Influence Factors of Abrasion Resistance of High-Flow Grade SEBS/PP Blended Thermoplastic Elastomer.

Hydrogenated styrene-butadiene-styrene block copolymer (SEBS)/polypropylene (PP) blended thermoplastic elastomer (TPE) is suitable for preparing the automotive interiors because of its excellent elasticity, softness, weather resistance, low odor, low VOC and other environmental-friendly properties. The skin of the automobile instrument panel is an appearance part, which requires excellent friction loss resistance of surface. In this paper, the high-flow SEBS/PP blended thermoplastic elastomer (TPE) suitable for the preparation of injection molding skins for automobile instrument panel was studied. By comparing the Taber abrasion and cross-scratch properties, the effects of SEBS's molecular weight, styrene content in the molecule, molecular structure and types of lubricating agents on the friction loss properties of the material were investigated. The results show that under the same SEBS molecular structure, the higher the molecular weight within a certain range, the better the wear resistance of high-flow SEBS/PP type TPE, but the ultra-high molecular weight exhibits lower wear resistance than high molecular weight; The high-flow SEBS/PP blended TPE prepared by medium styrene content SEBS has better abrasion resistance; TPE prepared by star SEBS is better than linear SEBS; Adding silane-based lubricating agents is beneficial to improve the friction loss resistance of the material, especially combined use of high and low molecular weight silicone.