A Comparative Evaluation of the Bonding Strength, Marginal Adaptation, and Microleakage of Dental Cements in Prosthodontics: An In Vitro Comparative Study.

BACKGROUND: The primary function of dental cement is to seal and support prosthodontic restorative materials. Proper selection of the dental cement contributes to the clinical success of the restoration. METHODS: A total of 166 molar tooth samples were prepared to simulate the type of tooth commonly found in prosthodontic practice. Each sample was restored using one of the tested dental cement materials employing a prestabilized methodology. The performance of resin-modified glass ionomer cement (RMGIC) (GC Fuji PLUS Capsule, GC America, Alsip, IL), zinc phosphate cement (ZPC) (Dentsply Sirona, Charlotte, NC), and resin cement (RC) (RelyX ARC, 3M ESPE, Saint Paul, MN) in bonding strength, marginal adaptation, and microleakage was evaluated and compared. The bonding strength, marginal adaptation, and microgroove were tested using specific established methodologies. The outcomes were then analyzed using statistical analyses for means and standard deviations to compare different types of dental cement. RESULTS: The total outcome shows that the highest bonding strength with the highest mean was the resin cement, rating 24.8 MPa, followed by RMGIC and ZPC at 20.5 and 18.9 MPa, respectively. The marginal adaptation scores indicate that RC had the highest score at a mean of 4, followed by ZPC at 3.2 and RMGIC at 2.5. The dye penetration measurements in millimeters revealed that ZPC had a penetration of 0.31 mm, RMGIC had a penetration of 0.25 mm, and RC had the least penetration at 0.20 mm. The results of the statistical data analysis show significant differences between the dental cements in bonding strength and marginal adaptation. CONCLUSION: In conclusion, resin cement demonstrated superior performance in bonding strength, marginal adaptation, and resistance to microleakage compared to RMGIC and zinc phosphate cement. These findings highlight the importance of selecting resin cement for achieving optimal clinical outcomes in prosthodontic restorations.

Touch-cure activation by marketed universal resin luting cements of their associated primer to dentin.

PURPOSE: The aim of this study was to investigate the dentin shear bond strength (SBS) and bonding interface of three recently developed "universal" resin luting cements based on different modalities. METHODS: The dentin SBS and interfacial analysis of three recently launched "universal" resin luting cements, namely, G-Cem One, RelyX Universal and Panavia SA cement universal, were studied. All bonding protocols, including the previous use of their dedicated primer or universal adhesive in touch-cure mode or light-cure mode were performed. Variolink Esthetic LC used in conjunction with Scotchbond Universal Plus was used as a control group. For each group (n = 9), 10 specimens were tested for dentin SBS and two were examined by scanning electron microscopy. SBS were analyzed by two-way ANOVA followed by Dunnett's test. RESULTS: SBS values showed that the three "universal" resin luting cements tested exhibit different adhesive behaviors. G-Cem One with its touch-cure activated primer had a greater SBS to dentin (25.5 MPa) than that of the control group (22.1 MPa). CONCLUSION: "Universal" resin luting cements have variable efficacy when used in self-curing mode. The touch-curing mode is also of concern but may show high potential for some formulations.

Prediction of excess cement residues using a regression model to avoid peri-implant diseases: An in vitro study.

Dental implant restorations attached to cement can potentially result in peri-implant mucositis and peri-implantitis if cement residues are present. Effectively predicting and eliminating such dental cement residues is crucial for preventing complications. This study focuses on creating a regression model using the pixel values to predict the Excess Cement Residues (ECR) by employing an octagonal surface imaging approach. A model featuring gingival imitation, ten abutments, and ten crowns was created, and the cemented implants underwent thorough photographic and analytical assessment. The ECR was determined through two distinct approaches: the Computerized Planimetric Method (CPM) and the weighing method. Across ten implants in this in vitro study, ECR varied from 0.3 to 21 mg, with an average of 5.69 mg. The findings reveal a higher amount of ECR on the distal, mesiobuccal, and mesial sides. Utilizing Pearson's correlation, a coefficient value of r = 0.786 signifies a strong correlation between CPM and the weighing method. The regression model further aids in predicting ECR based on pixel values. The octagonal surface imaging approach not only vividly captures information about ECR in the implant cementation region but also emphasizes the feasibility of ImageJ as an effective tool for detecting ECR. The congruence between CPM and the weighing method results supports the application of the regression model for precise ECR prediction.

The effect of three dental cement types on the corrosion of dental implant surfaces.

Statement of problem: One of the main challenges facing dental implant success is peri-implantitis. Recent evidence indicates that titanium (Ti) corrosion products and undetected-residual cement are potential risk factors for peri-implantitis. The literature on the impact of various types of dental cement on Ti corrosion is very limited. Purpose: This study aimed to determine the influence of dental cement on Ti corrosion as a function of cement amount and type. Materials and methods: Thirty commercially pure Ti grade 4 discs (19 × 7mm) were polished to mirror-shine (Ra ≈ 40 nm). Samples were divided into 10 groups (n = 3) as a cement type and amount function. The groups were no-cement as control, TempBond NE (TB3mm, TB5mm, and TB8mm), FujiCEM-II (FC3mm, FC5mm, and FC8mm), and Panavia-F-2.0 (PC3mm, PC5mm, and PC8mm). Tafel's method estimated corrosion rate (icorr) and corresponding potential (Ecorr) from potentiodynamic curves. Electrochemical Impedance Spectroscopy (EIS) data was utilized to obtain Nyquist and Bode plots. An equivalent electrical circuit estimated polarization resistance (Rp) and double-layer capacitance (Cdl). Inductively coupled plasma mass spectrometry (ICP-MS) analysis was conducted to analyze the electrolyte solution after corrosion. pH measurements of the electrolyte were recorded before and after corrosion tests. Finally, the corroded surface was characterized by a 3D white-light microscope and scanning electron microscope. Statistical analysis was conducted using either one-way ANOVA followed by Tukey's Post Hoc test or Kruskal-Wallis followed by Dunn's test based on data distribution. Results: Based on cement amount, FC and PC significantly increased icorr in higher amounts (FC8mm-icorr = 8.22 × 10-8A/cm2, PC8mm-icorr = 5.61 × 10-8A/cm2) compared to control (3.35 × 10-8A/cm2). In contrast, TB3mm decreased icorr significantly compared to the control. As a function of cement type, FC increased icorr the most. EIS data agrees with these observations. Finally, corroded surfaces had higher surface roughness (Ra) compared to non-corroded surfaces. Conclusion: The study indicated that cement types FC and PC led to increased Ti-corrosion as a function of a higher amount. Hence, the implant stability could be impacted by the selection, excessive cement, and a potentially increased risk of peri-implantitis.

Adhesive Bond Strength of Restorative Materials to Caries-Affected Dentin Treated with Antimicrobial Photodynamic Therapy: A Systematic Review and Meta-Analysis.

Objective: This systematic review aimed to evaluate the adhesive bond strength of restorative materials to caries-affected dentin (CAD) treated with antimicrobial photodynamic therapy (aPDT) in comparison with conventional chemical disinfectants. Methods: Three databases, including the Web of Science, Scopus, and PubMed, were searched to address the focused question: "What is the effect of aPDT compared to conventional chemical disinfection techniques on the adhesive bond strength of restorative materials to CAD?." Search keywords included "dentin*" "adhes bond*" "caries-affected dentin" "photodynamic "photochemotherapy" "photosensitizing agent" "phototherapy" "photoradiation" "laser" "light activated" "photoactivated." A fixed-effects model was used in each meta-analysis and the inverse variance was used to calculate the standard mean difference (SMD). For evaluating the statistical heterogeneity, the Cochrane's Q test and the I2 statistics were used. The risk of bias was evaluated based on the Cochrane Collaboration's tool. Results: Fourteen studies were included in the qualitative as well as quantitative analysis. The results of the meta-analyses exhibited an SMD of 2.38% [95% confidence interval (CI): 2.03-2.73; p < 0.00001], indicating a statistically significant difference in the shear bond strength scores between the tested group (samples treated with aPDT) and the control group (i.e., favoring the sound dentin and/or conventional chemical disinfectants). Contrarily, an SMD of -1.46% (95% CI: -2.04 to -0.88; p < 0.00001) and -0.37% (95% CI: -0.70 to -0.03; p = 0.03) was observed, indicating a statistically significant difference in the microtensile bond strength (µTBS), as well as microleakage scores between the tested group (favoring the samples treated with aPDT) and the control group (i.e., sound dentin and/or conventional chemical disinfectants). Conclusions: Adhesive bond strength of restorative materials to CAD treated with conventional chemical disinfectants showed superior outcomes compared to photodynamic therapy (aPDT).

The Effect of Casein Phosphopeptide-Amorphous Calcium Phosphate Containing Bonding Agents on Dentin Shear Bond Strength and Remineralization Potential: An in Vitro Study

ABSTRACT Objective: To assess the effect of Casein Phosphopeptide-Amorphous Calcium Phosphate (ACP) containing bonding agents on dentin shear bond strength and remineralization potential. Material and Methods: This in vitro study evaluated 45 extracted human premolars. The teeth were decoronated, and the tooth crown was split into buccal and lingual halves. The specimens were then flat-grounded by a 180-grit abrasive. The specimens were then randomized into three groups (n=15). Adper Scotchbond Multi-Purpose (SBMP) primer and adhesive were used for bonding in the control group. ACP in 10wt% and 20wt% concentrations was added to SBMP adhesive and used in groups 2 and 3, respectively. After the application of primer and adhesive and light-curing them for 10 s, a transparent silicon cylinder was placed on a dentin surface and cured for 10 s; then, the cylinder was filled with composite resin and was cured for the 40s from each side. The specimens underwent 3000 thermal cycles, and a universal testing machine measured the SBS. To assess the remineralization quality, a total of 6 dentin samples (2 specimens for group) were prepared and underwent X-ray diffraction, attenuated total reflection Fourier-transform infrared spectroscopy, and scanning electron microscopy-energy dispersive X-ray analysis. One-way analysis of variance was used to analyze the data. The level of p<0.05 was considered significant. Results: No significant difference in dentin shear bond strength was noted between the groups (p>0.05) - the addition of ACP to SBMP adhesive enhanced dentin remineralization. Increasing the ACP concentration from 10% to 20% increased the formation of hydroxyapatite. Conclusion: Adding amorphous calcium phosphate confers remineralizing property to SBMP adhesive without compromising its shear bond strength to dentin.

Finite element stress analysis of dental cement application on endocrown and onlay restoration.

The aim of the study was to evaluate the influence of resin cement material types on tooth with endocrown and onlay restorations. The first molar was scanned using Micro-CT and underwent a modelling process to obtain the 3D model for computational simulation. Eight models were simulated in the current study with two loading conditions (720N vertical load and 200N oblique load), two types of restoration (onlay and endocrown restorations), and two resin cement variants (dual-cure resin cement and light-cure resin cement). The tooth with onlay restoration showed a significant stress reduction (up to 70%) when using light-cure resin cement compared to dual-cure resin cement. In contrast, types of cement did not affect stress distribution in the tooth with endocrown restoration. The current study found that dual-cure resin cement was preferable in Endocrown and Onlay restorations, due to dual-cure resin cement provided better bond strength compared to light-cure resin cement.

In vitro cytotoxicity of resin cement and its influence on the expression of antioxidant genes.

AIM: This study evaluated cytotoxicity and antioxidant gene expression of resin cements on human gingival fibroblasts (hGF). MATERIALS AND METHOD: RelyX Ultimate™(RXU), Variolink™II(VLII), and RelyXU200™(RXU200) resin cements were incubated with culture medium for 24 h to obtain eluates. Then, the eluates were applied over hGF to assess cell viability at 24 h, 48 h, and 72 h and antioxidant gene expression at 24 h. hGF cultures non-exposed to the eluates were used as Control. Data were submitted to ANOVA and Bonferroni tests (α≤0.05). RESULTS: RXU and RXU200 reduced the number of viable cells in 24 h. Longer exposure to cement extracts caused cell death. Gene expression showed peroxiredoxin 1 (PRDX1) induction by all resin cement types, and superoxide dismutase 1 (SOD1) induction by RXU200 and VLII. Moreover, RXU200 induced not only PRDX1 and SOD1, but also glutathione peroxidase 1 (GPX1), catalase (CAT), and glutathione synthetase (GSS). CONCLUSIONS: All resin cements showed toxicity, and induced antioxidant genes in hGF. Antioxidant gene induction is at least partly associated with cytotoxicity of tested cements to oxidative stress experience.

OBJETIVO: O objetivo deste estudo foi avaliar a toxicidade dos cimentos resinosos Rely X Ultimate 2, Rely X U200 e Variolink II, bem como sua influência na expressão de genes antioxidantes em fibroblastos gengivais humanos. Materiais e Método: Corpos de prova de cada cimento foram colocados em meio de cultura por 24 h e os extratos correspondentes foram aplicados aos fibroblastos. A viabilidade celular foi avaliada após 24, 48 e 72 h de exposição pelo ensaio de exclusão do azul de tripano e MTT. A expressão gênica foi avaliada por PCR quantitativo após 24 h de exposição aos extratos. Estes parâmetros foram comparados aos das células não expostas aos cimentos. Os dados foram submetidos ao teste ANOVA, seguido pelo pós-teste de Bonferroni (a≤0.05). RESULTADOS: Os resultados demonstraram que todos os cimentos promoveram redução do número de células viáveis e da atividade mitocondrial nos períodos de 48 e de 72 h (p< 0,01), sendo que o Variolink II apresentou o menor efeito e os cimentos Rely X Ultimate e Rely X U200 promoveram similarmente os maiores efeitos. A análise de expressão gênica evidenciou influência significativa em todos os cimentos avaliados sobre os níveis de transcritos de PRDX1, SOD1, GPX1 e GSS (p> 0,05), com um aumento considerável no Rely X U200. Conclusão: A indução de genes antioxidantes está, pelo menos em parte, associada à citotoxicidade dos cimentos testados para a experiência de estresse oxidativo.

In vitro cytotoxicity of resin cement and its influence on the expression of antioxidant genes / Avaliação in vitro da toxicidade de cimentos resinosos e sua influência na expressão de genes antioxidantes em fibroblastos humanos

ABSTRACT Aim: This study evaluated cytotoxicity and antioxidant gene expression of resin cements on human gingival fibroblasts (hGF). Materials and Method: RelyX Ultimate™(RXU), Variolink™II(VLII), and RelyXU200™(RXU200) resin cements were incubated with culture medium for 24 h to obtain eluates. Then, the eluates were applied over hGF to assess cell viability at 24 h, 48 h, and 72 h and antioxidant gene expression at 24 h. hGF cultures non-exposed to the eluates were used as Control. Data were submitted to ANOVA and Bonferroni tests (α≤0.05). Results: RXU and RXU200 reduced the number of viable cells in 24 h. Longer exposure to cement extracts caused cell death. Gene expression showed peroxiredoxin 1 (PRDX1) induction by all resin cement types, and superoxide dismutase 1 (SOD1) induction by RXU200 and VLII. Moreover, RXU200 induced not only PRDX1 and SOD1, but also glutathione peroxidase 1 (GPX1), catalase (CAT), and glutathione synthetase (GSS). Conclusions: All resin cements showed toxicity, and induced antioxidant genes in hGF. Antioxidant gene induction is at least partly associated with cytotoxicity of tested cements to oxidative stress experience.

RESUMO Objetivo: O objetivo deste estudo foi avaliar a toxicidade dos cimentos resinosos Rely X Ultimate 2, Rely X U200 e Variolink II, bem como sua influência na expressão de genes antioxidantes em fibroblastos gengivais humanos. Materiais e Método: Corpos de prova de cada cimento foram colocados em meio de cultura por 24 h e os extratos correspondentes foram aplicados aos fibroblastos. A viabilidade celular foi avaliada após 24, 48 e 72 h de exposição pelo ensaio de exclusão do azul de tripano e MTT. A expressão gênica foi avaliada por PCR quantitativo após 24 h de exposição aos extratos. Estes parâmetros foram comparados aos das células não expostas aos cimentos. Os dados foram submetidos ao teste ANOVA, seguido pelo pós-teste de Bonferroni (a≤0.05). Resultados: Os resultados demonstraram que todos os cimentos promoveram redução do número de células viáveis e da atividade mitocondrial nos períodos de 48 e de 72 h (p < 0,01), sendo que o Variolink II apresentou o menor efeito e os cimentos Rely X Ultimate e Rely X U200 promoveram similarmente os maiores efeitos. A análise de expressão gênica evidenciou influência significativa em todos os cimentos avaliados sobre os níveis de transcritos de PRDX1, SOD1, GPX1 e GSS (p> 0,05), com um aumento considerável no Rely X U200. Conclusão: A indução de genes antioxidantes está, pelo menos em parte, associada à citotoxicidade dos cimentos testados para a experiência de estresse oxidativo.

Synthesis and characterization of a dental cement based on bioactive glass/zinc oxide modified with organic resin as a novel pulp capping agent.

This study aimed to synthesize and characterize a novel dental pulp capping cement containing bioactive glass (BG)/zinc oxide modified with an organic resin. BG (45S5) with or without ZnO (Zn) and hemaphosphate (HP) combined with a liquid consisting of polyacrylic and itaconic acids (AA) were synthesized and the structural, physical, and mechanical properties were assessed. Hydroxyapatite formation was evaluated by immersion in simulated body fluid. Biological analysis including methyl thiazolyl tetrazolium assay, alizarin red staining, alkaline phosphatase (ALP) activity, and gene expression of odontogenic markers were performed to evaluate the cytotoxic effect and biomineralization potential of the cements on human dental pulp stem cells (hDPSCs). A commercial mineral trioxide aggregate (MTA) served as control. The highest compressive strength value and the shortest setting time were belonged to the BG + HP + AA and BG + AA groups, respectively. The shear bond strength to dentin was the highest for the BG + HP + AA cement. Scanning electron microscope showed only scarce deposits of calcium phosphate formation on the surface of the synthesized cements. BG + HP + AA and BG + HP + Zn + AA groups had significantly lower cytotoxicity than MTA. The mineralization potential of hDPSCs after stimulation by the novel cements increased. Quantitative reverse-transcription-polymerase chain reaction showed higher odontogenic marker expression in hDPSCs exposed to the BG + HP + Zn + AA cement compared to other synthesized cements, although it was higher in MTA group. Based on the obtained results, the novel synthesized cements can be used as appropriate capping agents in the treatment of dental pulp.

Physicochemical, Biological, and Antibacterial Properties of Four Bioactive Calcium Silicate-Based Cements.

Calcium silicate-based cement (CSC) is a pharmaceutical agent that is widely used in dentistry. This bioactive material is used for vital pulp treatment due to its excellent biocompatibility, sealing ability, and antibacterial activity. Its drawbacks include a long setting time and poor maneuverability. Hence, the clinical properties of CSC have recently been improved to decrease its setting time. Despite the widespread clinical usage of CSC, there is no research comparing recently developed CSCs. Therefore, the purpose of this study is to compare the physicochemical, biological, and antibacterial properties of four commercial CSCs: two powder-liquid mix types (RetroMTA® [RETM]; Endocem® MTA Zr [ECZR]) and two premixed types (Well-Root™ PT [WRPT]; Endocem® MTA premixed [ECPR]). Each sample was prepared using circular Teflon molds, and tests were conducted after 24 h of setting. The premixed CSCs exhibited a more uniform and less rough surface, higher flowability, and lower film thickness than the powder-liquid mix CSCs. In the pH test, all CSCs showed values between 11.5 and 12.5. In the biological test, cells exposed to ECZR at a concentration of 25% showed greater cell viability, but none of the samples showed a significant difference at low concentration (p > 0.05). Alkaline phosphatase staining revealed that cells exposed to ECZR underwent more odontoblast differentiation than the cells exposed to the other materials; however, no significant difference was observed at a concentration of 12.5% (p > 0.05). In the antibacterial test, the premixed CSCs showed better results than the powder-liquid mix CSCs, and ECPR yielded the best results, followed by WRPT. In conclusion, the premixed CSCs showed improved physical properties, and of the premixed types, ECPR exhibited the highest antibacterial properties. For biological properties, none of these materials showed significant differences at 12.5% dilution. Therefore, ECPR may be a promising material with high antibacterial activity among the four CSCs, but further investigation is needed for clinical situations.

Knowledge of Saudi dental students and interns towards luting cements and their applications in fixed prosthodontics.

BACKGROUND: Enhancement of students' knowledge is essential in improving their clinical skills and performance. Thus, the curriculum should be prepared to achieve a better outcome. The current study aimed to determine the dental students' and interns' basic knowledge towards dental luting cements and their application in dental practice to improve the theoretical and clinical training sections. MATERIALS AND METHODS: A cross-sectional study was conducted among dental students and interns at three Colleges of Dentistry in the Kingdom of Saudi Arabia between September 2019-June 2020. An online questionnaire was used which included demographic data, questions about luting cement usage, cementation techniques, and commonly used cements in dental clinics. Descriptive analysis and chi-square test were used to show the association between level of dental education and the use of dental cements using SPSS software. The significance level was set at 5%. RESULTS: The total respondents were 626 dental students/interns of whom 78.8% were undergraduate dental students. Participants who reported undergraduate studies as the source of information were 79.7%. The type of restoration was the main factor in luting cement selection (62.6%). Concerning the isolation technique in cementing laminate veneers, 49.7% used dri-angles, cotton rolls and saliva ejectors. Dual-cure resin cement was the most common cement used in all the mentioned restorations except in pressed porcelain laminate veneers and cement-retained implant-supported restorations. CONCLUSIONS: Students' knowledge and practice in managing dental implants and porcelain laminate veneers need to be improved. The selection of a luting agent for a given restoration by students and interns was based on the basic knowledge, available cement, and the type of restoration. Awareness towards the management of short prepared teeth and custom-made cast posts and cores is also limited.

Resistencia de unión al cizallamiento de diferentes agentes de fijación a aleaciones metálicas odontológicas / Shear bond strength of different bonding agents to dental metal alloys

Introducción: La fijación de las restauraciones indirectas es uno de los pasos más importantes, para conseguir una adecuada retención y sellado de la interfase entre el material restaurador y el diente. Objetivo: Evaluar la resistencia de unión al cizallamiento de diferentes agentes de fijación a dos aleaciones metálicas utilizadas en odontología. Métodos: Estudio experimental in vitro. Cien especímenes de aleaciones de metales base, 50 de níquel-cromo y 50 de níquel-cromo-titanio fueron preparados y divididos de manera aleatoria en 5 grupos. Esta división se realizó acorde con el agente de fijación utilizado: sistema autograbante de dos pasos (Clearfil SE Bond; CSB), sistema adhesivo universal (Single Bond Universal; SBU), cemento resinoso autoadhesivo (Maxcem Elite; ME), ionómero de vidrio (IV) y fosfato de zinc (ZnPO). Posteriormente a la aplicación de cada agente de fijación, los especímenes tratados fueron almacenados en agua destilada por 24 h a 37 ºC y sometidos a un ensayo de resistencia de unión al cizallamiento. Resultados: La resistencia de unión al cizallamiento fue influenciada significativamente por el tipo de agente de fijación (p = 0,002) y el tipo de aleación utilizada (p < 0,001). La resistencia de unión al cizallamiento fue mayor, al utilizar el sistema Clearfil SE Bond, seguida de Single Bond Universal; las diferencias entre Maxcem Elite y el Fosfato de zinc no fueron significativas. Finalmente, el IV no mostró adhesión a ninguna de las aleaciones metálicas utilizadas. Conclusiones: El uso de Clearfil SE Bond aumentó la resistencia de unión de los cementos resinosos a las aleaciones metálicas(AU)

Introduction: The bonding of indirect restorations is one of the most important steps, in order to achieve adequate retention and sealing of the interface between the restorative material and the tooth. Objective: To evaluate the shear bond strength of different bonding agents to two metal alloys used in dentistry. Methods: In vitro experimental study. One hundred specimens of base metal alloys, 50 nickel-chromium and 50 nickel-chromium-titanium were prepared and randomly divided into 5 groups. This division was made according to the bonding agent used: two-step self-etching system (Clearfil SE Bond; CSB), universal adhesive system (Single Bond Universal; SBU), self-adhesive resin cement (Maxcem Elite; ME), glass ionomer (IV) and zinc phosphate (ZnPO). After the application of each bonding agent, the treated specimens were stored in distilled water for 24 hr at 37 ºC and subjected to a shear bond strength test. Results: Shear bond strength was significantly influenced by the type of bonding agent (p = 0.002) and the type of alloy used (p < 0.001). Shear bond strength was highest when using the Clearfil SE Bond system, followed by Single Bond Universal; the differences between Maxcem Elite and Zinc Phosphate were not significant. Finally, IV did not show adhesion to any of the metal alloys used. Conclusions: The use of Clearfil SE Bond increased the bond strength of resinous cements to metallic alloys(AU)

Biomechanical Testing of Two-Unit Bridges and a Comparison of Replacement Retention Depending on a Cementation Medium, Replacement Position, and Gap Size.

Dental replacements are placed between the abutment teeth. The exceptions are two-unit bridges, as they are supported by a single tooth prepared only on one side of the missing tooth. The presented study deals with an analysis of a pressure force action on two-unit bridges placed in the frontal part (20 samples), where the pressure action is lower, and in the distal part (20 samples), where the pressure action is higher. A CAD program by 3Shape was used for digital designing with two different gap settings, 10 µm (20 samples) and 30 µm (20 samples). Two-unit bridges were attached to the prepared tooth using two types of dental cement (20/20 samples), which were selected for their physical and bioactive properties. All two-unit bridges (a total of 80 samples) were fabricated from CoCr alloys on Mlab cusing R by applying the Selective Laser Melting (SLM) technology. Mechanical testing was performed using the Inspekt5 table blue. The obtained data were used to verify the hypotheses-a difference between both types of cement (A ≠ B), a difference between the frontal and distal two-unit bridges (F ≠ D) and a difference between the gap sizes (10 ≠ 30). To confirm the given theories, data were statistically evaluated using the F-test and subsequent t-tests. The resulting p-value was compared with the level of significance (α = 0.05). A statistical evaluation revealed a significant difference between the compared groups; however, no explicit correlation between the individual groups of specimens was identified.

Novel rechargeable nano-calcium phosphate and nano-calcium fluoride resin cements.

OBJECTIVE: In most clinical circumstances, secondary caries at the margin of fixed dental restorations leads to restoration failure and replacement. Accordingly, the objectives of this study were to: (1) develop a novel rechargeable nano-calcium phosphate (NACP) and nano-calcium fluoride (nCaF2) resin-based cement; and (2) investigate their mechanical properties and calcium (Ca), phosphate (P), and fluoride (F) ion release, recharge, and re-release for the first time. METHODS: The cement matrix consisted of pyromellitic glycerol dimethacrylate (PMGDM), ethoxylated bisphenol-A-dimethacrylate (EBPADMA) was denoted PEHB. Four cements were fabricated: (1) PEHB+0%NACP+0%nCaF2 (experimental control); (2) PEHB+25%NACP+0%nCaF2, (3) PEHB+0%NACP+25%nCaF2; (4) PEHB+12.5%NACP+12.5% nCaF2. RelyX luting cement was used as a commercial control. Mechanical properties and long-term Ca, P, and F ion release, recharge, and re-release were evaluated. RESULTS: Adding 25% NACP, 25% nCaF2 and adding both 12.5% NACP and 12.5% nCaF2 to the cement matrix presented a significantly higher shear bond strength, flexural strength compared to the commercial control (p < 0.05) with a comparable outcome with no significant different (p > 0.05) compared to experimental control. The film thickness results of all cement groups met the ISO requirement (<50 µm). The resin cement group with both 12.5% NACP and 12.5% nCaF2 successfully released Ca, P, and F ions at 3.1 ± 0.01, 1.1 ± 0.05, and 0.51±0.01 mmol/L respectively. Moreover, it showed the ability to re-release Ca, P, and F ions at 0.62±0.01, 0.12±0.01, and 0.42±0.01 mmol/L respectively. CONCLUSIONS: The resin cement group with both 12.5% NACP and 12.5% nCaF2 demonstrated the advantages of both types of bio-interactive fillers as it could release a higher level of ions than the resin cement with 25%nCAF2 and exhibited a better rechargeability compared to the resin cement with 25%NACP. CLINICAL SIGNIFICANCE: The ability of this novel resin-based cement to release, recharge, and re-release Ca, P, and F ions could be one of the keys to lengthening the survivability of fixed dental restorations. These features could help to reduce the onset of secondary caries by enhancing the remineralization and preventing the demineralization of tooth structures.

Cement selection criteria for different types of intracanal posts.

Background: To consciously select an appropriate dental cement for each type of intracanal post. Materials and Methods: An electronic search was carried out (1970 to 2020) through Medline, PubMed, Scopus, and Google Scholar. The following keywords were searched in title, abstract, or keywords with different combinations: endodontically treated tooth, root canal therapy, dental posts, post and core, prefabricated posts, custom posts, dental cement, resin cements, cement selection, cement, and adhesive resin cement. Results: Evaluating full texts, 146 articles were selected to review the types of posts and cements, selection criteria of appropriate cement for each type of post, and compare the results obtained by different cements. Conclusion: Dental cements affect the survival rate, durability, and success rate of postbased treatments. Considering special characteristics and application of each type of intracanal post, conscious selection of cement is an important determining factor in long-lasting success. Choosing an appropriate cement has a key role in success and durability of dowel posts-based fixed restorations.

Cytotoxicity of two self-adhesive resin cements and their interference in the phagocytic activity of murine macrophages.

Objectives: This study aimed to evaluate in vitro the effects of the self-adhesive resin cements RelyX U200 (3M ESPE) and seT PP (SDI Limited) on murine macrophages and the interference of the photoactivation. Materials and Methods: Cell viability assays, cell adherence, yeast phagocytosis of Saccharomyces boulardii and production of reactive oxygen species (ROS) were performed in the presence of capillaries containing the respective self-adhesive cement when photoactivated or not. Results: After long periods of contact, both types of cements, when not photoactivated, are more cytotoxic for macrophages. The seT PP cement when only chemically activated seems to interfere more negatively in the process of phagocytosis of yeasts S. boulardii. Both types of cements interfere in the cell adhesion process, independent of photoactivation. None of the types of cements tested was able to induce the production of ROS. Conclusions: Our results highlight the great importance of the photoactivation of self-adhesive resin cements in the dental clinic, since RelyX U200, when photoactivated, presented the best results within the evaluated parameters.

Computational study of the relative stability of some glass-ionomer cement-forming molecules.

This work is part of a larger study whose main objective was to find a series of promising molecules to be used as glass-ionomer-type materials. The project was divided into 3 successive stages; the results of the first stage have been previously published and were used to continue the study. The molecules evaluated in the second stage were constructed by adding a glycidyl methacrylate molecule to the carboxylic groups of the polyacids selected in the previous stage. The modeling was done using the density functional theory for M06-2X/6-311G(d,p). The results indicate that the addition over the carboxylic groups of the fraction of the molecule, corresponding to itaconic acid, is thermodynamically favored. The final stage was modeled with the M06 functional and consisted of obtaining basic structures of glass-ionomer-type materials, by acid-base reaction between the molecules resulting from the second stage with individual ions of Ca (2 +), Zn (2 +), or Al (+ 3). It was concluded that aluminum atoms generate more compact structures that would correlate with more resistant materials.

Shear bond strength of different luting agents to polyether ether ketone.

Background: Polyether ether ketone (PEEK) was recently introduced to dentistry. However, difficulty in provision of a strong durable bond is its main drawback. Thus, precise surface treatment and use of a suitable luting agent are imperative for bonding of PEEK restorations. This study aimed to assess the effect of type of luting agent on shear bond strength (SBS) of PEEK. Materials and Methods: In this in vitro study, 60 square-shaped PEEK samples were fabricated and sandblasted with 110 µm Al2O3 particles. The samples were then divided into four groups based on the type of cement used (n = 15): zinc phosphate cement, Panavia F2, Panavia V5, and resin-modified glass-ionomer (RMGI) cement. After bonding, the samples were thermocycled for 5000 cycles. The SBS was measured by a universal testing machine. The surface of samples was inspected under a video measuring machine to determine the mode of failure. Data were analyzed using the Kruskal-Wallis test via SPSS version 24 (α = 0.05). and Methods: In this in vitro study, 60 square-shaped PEEK samples were fabricated and sandblasted with 110 µm Al2O3 particles. The samples were then divided into four groups based on the type of cement used (n = 15): zinc phosphate cement, Panavia F2, Panavia V5, and resin-modified glass-ionomer (RMGI) cement. After bonding, the samples were thermocycled for 5000 cycles. The SBS was measured by a universal testing machine. The surface of samples was inspected under a video measuring machine to determine the mode of failure. Data were analyzed using the Kruskal-Wallis test via SPSS version 24 (α = 0.05). Results: RMGI did not bond to PEEK. The SBS values were 4.02 ± 2.87 megapascals (MPa) for Panavia V5, 10.84 ± 6.05 MPa for Panavia F2, and 10.50 ± 2.88 MPa for zinc phosphate. The SBS in the Panavia V5 group was significantly lower than that in the Panavia F2 (P = 0.001) and zinc phosphate (P < 0.001) groups. No significant difference existed between the Panavia F2 and zinc phosphate groups in this respect (P > 0.05). Conclusion: Panavia F2 resin cement and zinc phosphate conventional cement provided the highest bond strength to PEEK, while RMGI did not bond to PEEK.

Microtensile resistance of an adhesive system modified with chitosan nanoparticles.

Aim: The aim of this study was to evaluate whether 2.5% chitosan applied after dentin acid etching or incorporated into the adhesive system interferes with the microtensile strength of the interface tooth-resin. Subjects and Methods: Sixty healthy bovine teeth had the incisal thirds and the roots sectioned and were randomly allocated into three groups (n = 60). G1 (control): acid attack + Clearfil SE Bond + Z350 resin; G2: treatment with 2.5% chitosan + Clearfil SE Bond + Z350 resin; G3: treatment with 2.5% chitosan incorporated into dentin adhesive + Z350 resin. The stick-shaped specimens made in each group were randomly divided into two subgroups and subjected to degradation of the adhesive interface (with aging: specimens immersed in 2.5% sodium hypochlorite for 12 h and washed in distilled water for 1 h, and without aging). The groups were submitted to a microtensile strength test with a 0.5 mm/min speed until rupture. Statistical analysis of the data was performed according to normal distribution. Results: Microtensile data were obtained by calculating the area of each toothpick, obtaining values in megapascal. No aging: G1 - 5251.69, G2 - 5.52 ± 1.46, and G3 - 3.91 ± 1.21. With aging: G1 - 3.45 ± 1.29, G2 - 2.75 ± 0.78, and G3 - 3.53 ± 1.33. Statistical analysis showed that the aging factor and adhesive modification decreased the bonding strength of the resin-dentin (P = 0.001). As well, the interaction between the analyzed factors showed statistically significant differences (P = 0.002). Conclusions: Accelerated aging decreases the adhesion strength in G1, even when chitosan is previously applied to the adhesive system. However, when adding chitosan to the adhesive, adhesion remained similar after aging but lower when compared to the other groups.