Concave Grain Boundaries Stabilized by Boron Segregation for Efficient and Durable Oxygen Reduction.

The oxygen reduction reaction (ORR) is a critical process that limits the efficiency of fuel cells and metal-air batteries due to its slow kinetics, even when catalyzed by platinum (Pt). To reduce Pt usage, enhancing both the specific activity and electrochemically active surface area (ECSA) of Pt catalysts is essential. Here, ultrafine, grain boundary (GB)-rich Pt nanoparticle assemblies are proposed as efficient ORR catalysts. These nanowires offer a large ECSA and a high density of concave GB sites, which improve specific activity. Atoms at these GB sites exhibit increased coordination and lattice distortion, leading to a favorable reduction in oxygen binding energy and enhanced ORR performance. Furthermore, boron segregation stabilizes these GBs, preserving active sites during catalysis. The resulting boron-stabilized Pt nanoassemblies demonstrate ORR specific and mass activities of 9.18 mA cm-2 and 6.40 A mg-1 Pt (at 0.9 V vs. RHE), surpassing commercial Pt/C catalysts by over 35-fold, with minimal degradation after 60 000 potential cycles. This approach offers a versatile platform for optimizing the catalytic performance of a wide range of nanoparticle systems.

Unraveling Lattice-Distortion Hardening Mechanisms in High-Entropy Carbides.

Uncovering the hardening mechanisms is of great importance to accelerate the design of superhard high-entropy carbides (HECs). Herein, the hardening mechanisms of HECs by a combination of experiments and first-principles calculations are systematically explored. The equiatomic single-phase 4- to 8-cation HECs (4-8HECs) are successfully fabricated by the two-step approach involving ultrafast high-temperature synthesis and hot-press sintering techniques. The as-fabricated 4-8HEC samples possess fully dense microstructures (relative densities of up to ≈99%), similar grain sizes, clean grain boundaries, and uniform compositions. With the elimination of these morphological properties, the monotonic enhancement of Vickers hardness and nanohardness of the as-fabricated 4-8HEC samples is found to be driven by the aggravation of lattice distortion. Further studies show no evident association between the enhanced hardness of the as-fabricated 4-8HEC samples and other potential indicators, including bond strength, valence electron concentration, electronegativity mismatch, and metallic states. The work unveils the underlying hardening mechanisms of HECs and offers an effective strategy for designing superhard HECs.

Copper Intercalation Induces Amorphization of 2D Cu/WO3 for Room-Temperature Ferromagnetism.

Ferromagnetism in the two-dimensional limit has become an intriguing topic for exploring new physical phenomena and potential applications. To induce ferromagnetism in 2D materials, intercalation has been proposed to be an effective strategy, which could introduce lattice distortion and unpaired spin into the material to modulate the magnetocrystalline anisotropy and magnetic exchange interactions. To strengthen the understanding of the magnetic origin of 2D material, Cu was introduced into a 2D WO3 through chemical intercalation in this work (2D Cu/WO3). In contrast to the diamagnetic nature of the Cu and the WO3, room-temperature ferromagnetism was characterized for 2D Cu/WO3. Experimental and theoretical results attribute the ferromagnetism to the bound magnetic polaron in 2D Cu/WO3, which is consist of unpaired spins from W5+/W4+ with localized carriers from oxygen vacancies. Overall, this work provides a novel approach to introduce ferromagnetism into diamagnetic WO3, which could be applied for a wider scope of 2D materials.

Intercalation-Induced Irreversible Lattice Distortion in Layered Double Hydroxides.

Inducing strain in the lattice effectively enhances the intrinsic activity of electrocatalysts by shifting the metal's d-band center and tuning the binding energy of reaction intermediates. NiFe-layered double hydroxides (NiFe LDHs) are promising electrocatalysts for the oxygen evolution reaction (OER) due to their cost-effectiveness and high catalytic activity. The distorted ß-NiOOH phase produced by the Jahn-Teller effect under the oxidation polarization is known to exhibit superior catalytic activity, but it eventually transforms to the undistorted γ-NiOOH phase during the OER process. Such a reversible lattice distortion limits the OER activity. In this study, we propose a facile boron tungstate (BWO) anion intercalation method to induce irreversible lattice distortion in NiFe LDHs, leading to significantly enhanced OER activity. Strong interactions with BWO anions induce significant stress on the LDH's metal-hydroxide slab, leading to an expansion of metal-oxygen bonds and subsequent lattice distortion. In situ Raman spectroscopy revealed that lattice-distorted NiFe LDHs (D-NiFe LDHs) stabilize the ß-NiOOH phase under the OER conditions. Consequently, D-NiFe LDHs exhibited low OER overpotentials (209 and 276 mV for 10 and 500 mA cm-2, respectively), along with a modest Tafel slope (33.4 mV dec-1). Moreover, D-NiFe LDHs demonstrated excellent stability at 500 mA cm-2 for 50 h, indicating that the lattice distortion of the LDHs is irreversible. The intercalation-induced lattice strain reported in this study can provide a general strategy to enhance the activity of electrocatalysts.

Phase Transition Modulated by Grain Size and Lattice Distortion in Layered Transition Metal Oxide for Sodium-Ion Batteries.

Low-cost sodium-ion batteries have demonstrated great prospects in energy storage, among which layered transition metal oxides hold great potential as a cathode material. However, the notorious phase transition in layered cathode materials has greatly hampered their cycle life due to large volume changes upon desodiation/sodiation. In this study, by adopting an O3-type NaNi1/3Fe1/3Mn1/3O2 (NFM) with controlled synthesis temperatures, we have revealed that the grain size is closely related to its phase transition behaviors. The layered material with a smaller grain size and more distorted lattice tends to experience a shorter plateau of the O3-P3-O3 phase transitions during the charge/discharge process. Despite having a lower nominal discharge capacity without the phase transition plateau, its cycling stability increases from 77.4% to 96.2% after 100 cycles with greatly reduced intragranular cracks. The smaller grain size and lattice distortion act as a barrier that prevents the smooth layer from gliding upon sodium intercalation and deintercalation. This study focuses on the influence of grain size on battery cycle stability and provides a basis for future analysis of the structural instability of layered materials.

Lattice Distortion Promotes Incipient Plasticity in Multiprincipal Element Alloys.

Multiprincipal element alloys usually exhibit earlier pop-in events than pure metals and dilute solid solutions during nanoindentation experiments. To understand the origin of this phenomenon, large-scale atomic simulations of nanoindentation were performed on a series of metallic materials to investigate the underlying physics of incipient plasticity at the nanoscale. Statistical result shows that lattice distortion δ and normalized critical pressure pc/Es follow a power-law relationship. Via quantitative analysis on the relative positions of the atoms within the nearest neighbor shell, the physical origin of premature incipient plasticity is revealed as severe lattice distortion induces large relative atomic displacement, so only a small indentation strain is required to meet the critical displacement threshold that triggers incipient plasticity. Therefore, for perfect crystals, lattice distortion is an intrinsic and determinative factor that affects the first pop-in event.

2D Hybrid Perovskites: From Static and Dynamic Structures to Potential Applications.

2D perovskites have received great attention recently due to their structural tunability and environmental stability, making them highly promising candidates for various applications by breaking property bottlenecks that affect established materials. However, in 2D perovskites, the complicated interplay between organic spacers and inorganic slabs makes structural analysis challenging to interpret. A deeper understanding of the structure-property relationship in these systems is urgently needed to enable high-performance tunable optoelectronic devices. Herein, this study examines how structural changes, from constant lattice distortion and variable structural evolution, modeled with both static and dynamic structural descriptors, affect macroscopic properties and ultimately device performance. The effect of chemical composition, crystallographic inhomogeneity, and mechanical-stress-induced static structural changes and corresponding electronic band variations is reported. In addition, the structure dynamics are described from the viewpoint of anharmonic vibrations, which impact electron-phonon coupling and the carriers' dynamic processes. Correlated carrier-matter interactions, known as polarons and acting on fine electronic structures, are then discussed. Finally, reliable guidelines to facilitate design to exploit structural features and rationally achieve breakthroughs in 2D perovskite applications are proposed. This review provides a global structural landscape of 2D perovskites, expected to promote the prosperity of these materials in emerging device applications.

Sub-2 nm Microstrained High-Entropy-Alloy Nanoparticles Boost Hydrogen Electrocatalysis.

High-entropy alloys (HEAs) confine multifarious elements into the same lattice, leading to intense lattice distortion effect. The lattice distortion tends to induce local microstrain at atomic level and thus affect surface adsorptions toward different adsorbates in various electrocatalytic reactions, yet remains unexplored. Herein, this work reports a class of sub-2 nm IrRuRhMoW HEA nanoparticles (NPs) with distinct local microstrain induced by lattice distortion for boosting alkaline hydrogen oxidation (HOR) and evolution reactions (HER). This work demonstrates that the distortion-rich HEA catalysts with optimized electronic structure can downshift the d-band center and generate uncoordinated oxygen sites to enhance the surface oxophilicity. As a result, the IrRuRhMoW HEA NPs show a remarkable HOR kinetic current density of 8.09 mA µg-1 PGM at 50 mV versus RHE, 8.89, 22.47 times higher than those of IrRuRh NPs without internal strain and commercial Pt/C, respectively, which is the best value among all the reported non-Pt based catalysts. IrRuRhMoW HEA NPs also display great HER performances with a turnover frequency (TOF) value of 5.93 H2 s-1 at 70 mV versus RHE, 4.6-fold higher than that of Pt/C catalyst, exceeding most noble metal-based catalysts. Experimental characterizations and theoretical studies collectively confirm that weakened hydrogen (Had) and enhanced hydroxyl (OHad) adsorption are achieved by simultaneously modulating the hydrogen adsorption binding energy and surface oxophilicity originated from intensified ligand effect and microstrain effect over IrRuRhMoW HEA NPs, which guarantees the remarkable performances toward HOR/HER.

van der Waals Engineering of Charge Density Waves in One-Dimensional Nb6Te6 Nanowires.

One-dimensional (1D) systems have played a crucial role in the development of fundamental physics and practical applications. Recently, transition metal monochalcogenide (TMM) wires based on molybdenum (Mo) and tungsten (W) have emerged as promising platforms for investigating 1D physics in pure van der Waals (vdW) platforms. Here, we report on the bottom-up fabrication of Nb6Te6 wires down to the single-wire limit. The unique properties of Nb6Te6 single wire enable the realization of 1D charge density wave (CDW) phases in an isolated single TMM wire. Moreover, we revealed the appealing regulation of 1D CDW orders by van der Waals interactions at either the 1D-2D interface (i.e., rotation of a single wire along its wire axis) or the 1D-1D interface. Two rotation angles (30° and 0°) give rise to 3 × 1 and zigzag chain CDW morphologies, respectively, which exhibit pronounced differences in atomic displacement by a factor of 2. The interwire vdW coupling overwhelms its counterpart at the 1D-2D interface, thus locking the rotation angle (at 0°) as well as the interwire atomic registries. In contrast, interestingly, the phases of the charge oscillations are independent of the adjacent wires. The ability to tailor 1D charge orders provides a crucial addition to the toll set of vdW integrations beyond two-dimensional materials.

Constructing Bipolar Dual-Active Sites through High-Entropy-Induced Electric Dipole Transition for Decoupling Oxygen Redox.

It remains a significant challenge to construct active sites to break the trade-off between oxidation and reduction processes occurring in battery cathodes with conversion mechanism, especially for the oxygen reduction and evolution reactions (ORR/OER) involved in the zinc-air batteries (ZABs). Here, using a high-entropy-driven electric dipole transition strategy to activate and stabilize the tetrahedral sites is proposed, while enhancing the activity of octahedral sites through orbital hybridization in a FeCoNiMnCrO spinel oxide, thus constructing bipolar dual-active sites with high-low valence states, which can effectively decouple ORR/OER. The FeCoNiMnCrO high-entropy spinel oxide with severe lattice distortion, exhibits a strong 1s→4s electric dipole transition and intense t2g(Co)/eg(Ni)-2p(OL) orbital hybridization that regulates the electronic descriptors, eg and t2g, which leads to the formation of low-valence Co tetrahedral sites (Coth) and high-valence Ni octahedral sites (Nioh), resulting in a higher half-wave potential of 0.87 V on Coth sites and a lower overpotential of 0.26 V at 10 mA cm-2 on Nioh sites as well as a superior performance of ZABs compared to low/mild entropy spinel oxides. Therefore, entropy engineering presents a distinctive approach for designing catalytic sites by inducing novel electromagnetic properties in materials across various electrocatalytic reactions, particularly for decoupling systems.

Promotion of Acid-Water Oxidation by Lattice Distortion and Orbital Hybridization Induced by Ionic Dopant in Pyrochlore Y2Ru2O7.

For acid-water oxidation, pyrochloric ruthenates are thought to be extremely effective electrocatalysts. In this work, through partial B-site replacement with larger M2+ cations, the electronic states of Y2Ru2O7 with strong electron correlations are reasonably managed, by which the inherent performance is tremendously promoted. Based on this, the improved Y2Ru1.9Sr0.1O7 electrocatalyst exhibits an outstanding durability and presents a highly inherent mass activity of 1915.1 A gRu-1 (at 1.53 V vs RHE). The enhanced oxygen-evolving reaction (OER) activity by ionic dopant in YRO pyrochlore can be attributed to two aspects, i.e., the lattice distortion induced inhibition of the grain coarsening, which results in a large surface area for YRO-M and increases the OER active sites, and the weakening of electron correlation via broadening of the Ru 4d bandwidths due to the increase of the average radius of B-site ions, which gives rise to an enhancement of conductivity and a strengthened hybridization between Ru 4d and O 2p orbitals and improves the reaction kinetics. The synergistic effects of lattice distortion and orbital hybridization promote the enhanced OER activity. The results would provide fresh concepts for the design of improved electrocatalysts and underscore the significance of managing the intrinsic performance through the dual modification of microstructure morphology and electronic structure.

Suppressed Phase Segregation with Small A-Site and Large X-Site Incorporation for Photostable Wide-Bandgap Perovskite Solar Cells.

Wide-bandgap (WBG) perovskite solar cells (PSCs) have been widely used as the top cell of tandem solar cells. However, photoinduced phase segregation and high open-circuit voltage loss pose significant obstacles to the development of WBG PSCs. Here, a two-step small-size A-site and large-size X-site incorporation strategy is reported to modulate the lattice distortion and improve the film quality of WBG formamidinium-methylammonium (FAMA) perovskite films for photostable PSCs based on two-step deposition method. First, CsI with content of 0-20% is introduced to tune the lattice distortion and film quality of FAMA perovskite with a bandgap of 1.70 eV. Then, 4% RbI is incorporated to further modulate the perovskite growth and lattice distortion, leading to the suppression of photoinduced phase segregation in the resultant RbCsFAMA quadruple cation perovskites. As a result, the 20%CsI/4%RbI-doped device obtains a promising efficiency of 20.6%, and the corresponding perovskite film shows good photothermal stability. Even without encapsulation, the device can maintain 92% of its initial efficiency after 1000 h of continuous operation under 1 sun equivalent white light-emitting diode illumination.

Ultra-Efficient and Cost-Effective Platinum Nanomembrane Electrocatalyst for Sustainable Hydrogen Production.

Hydrogen production through hydrogen evolution reaction (HER) offers a promising solution to combat climate change by replacing fossil fuels with clean energy sources. However, the widespread adoption of efficient electrocatalysts, such as platinum (Pt), has been hindered by their high cost. In this study, we developed an easy-to-implement method to create ultrathin Pt nanomembranes, which catalyze HER at a cost significantly lower than commercial Pt/C and comparable to non-noble metal electrocatalysts. These Pt nanomembranes consist of highly distorted Pt nanocrystals and exhibit a heterogeneous elastic strain field, a characteristic rarely seen in conventional crystals. This unique feature results in significantly higher electrocatalytic efficiency than various forms of Pt electrocatalysts, including Pt/C, Pt foils, and numerous Pt single-atom or single-cluster catalysts. Our research offers a promising approach to develop highly efficient and cost-effective low-dimensional electrocatalysts for sustainable hydrogen production, potentially addressing the challenges posed by the climate crisis.

Concentrated Formic Acid from CO2 Electrolysis for Directly Driving Fuel Cell.

The production of formic acid via electrochemical CO2 reduction may serve as a key link for the carbon cycle in the formic acid economy, yet its practical feasibility is largely limited by the quantity and concentration of the product. Here we demonstrate continuous electrochemical CO2 reduction for formic acid production at 2 M at an industrial-level current densities (i.e., 200 mA cm-2 ) for 300 h on membrane electrode assembly using scalable lattice-distorted bismuth catalysts. The optimized catalysts also enable a Faradaic efficiency for formate of 94.2 % and a highest partial formate current density of 1.16 A cm-2 , reaching a production rate of 21.7 mmol cm-2 h-1 . To assess the practicality of this system, we perform a comprehensive techno-economic analysis and life cycle assessment, showing that our approach can potentially substitute conventional methyl formate hydrolysis for industrial formic acid production. Furthermore, the resultant formic acid serves as direct fuel for air-breathing formic acid fuel cells, boasting a power density of 55 mW cm-2 and an exceptional thermal efficiency of 20.1 %.

Enhanced Spin-Polarized Electric Field Modulating p-Band Center on Ni-Doped CdS for Boosting Photocatalytic Hydrogen Evolution.

It is a challenge to regulate charge separation dynamics and redox reaction kinetics at the atomic level to synergistically boost photocatalytic hydrogen (H2) evolution. Herein, a robust Ni-doped CdS (Ni-CdS) photocatalyst is synthesized by incorporating highly dispersed Ni atoms into the CdS lattice in substitution for Cd atoms. Combined characterizations with theoretical analysis indicate that local lattice distortion and S-vacancy of Ni-CdS induced by Ni incorporation lead to an increased dipole moment and enhanced spin-polarized electric field, which promotes the separation and transfer of photoinduced carriers. In this contribution, charge redistribution caused by enhanced internal electric field results in the downshift of the S p-band center, which is conducive to the desorption of intermediate H* for boosting the H2 evolution reaction. Accordingly, the Ni-CdS photocatalyst shows a remarkably improved photocatalytic performance with an H2 evolution rate of 20.28 mmol g-1 h-1 under visible-light irradiation, which is 5.58 times higher than that of pristine CdS. This work supplied an insightful understanding that the enhanced polarization electric field governs the p-band center for efficient photocatalytic H2 evolution activity.

Efficient Tin Perovskite Solar Cells via Suppressing Autoxidation in Inert Atmosphere.

The unsatisfactory power conversion efficiency (PCE) and long-term stability of tin perovskite solar cells (TPSCs) restrict its further development as alternatives to lead perovskite solar cells (LPSCs). Considerable research has focused on the negative impacts of O2 and H2 O, while discussions about degradation mechanism in an inert atmosphere remains insufficient. Herein, the light-induced autoxidation of tin perovskite in nitrogen atmosphere is revealed for the first time and the elastic lattice distortion is demonstrated as the crucial role of rapid degradation. The continuous injection of photons induces energy transfer from excited A-site cations to vibrating Sn-I framework, leading to the elastic deformation of perovskite lattice. Consequently, the over distorted Sn-I framework releases free iodine and further oxidizes Sn2+ in the form of molecular iodine. Through an appropriately designed light-dark cyclic test, a remarkable PCE of 14.41% is achieved based on (Cs0.025 (MA0.25 FA0.75 )0.975 ) 0.98 EDA0.01 SnI3 solar cells, which is the record of hybrid triple TPSCs so far. The findings unveil autoxidation as the crux of TPSCs' degradation in an inert atmosphere and suggest the possibility of reinforcing the tin perovskite lattice towards highly efficient and stable TPSCs.

Regulating Grind-Induced Lattice Distortion for Nickel-Rich Cathodes by Annealing.

The commercialization of high-performance nickel-rich cathodes always awaits a cost-effective, environmentally friendly, and large-scale preparation method. Despite a grinding process normally adopted in the synthesis of the nickel-rich cathodes, lattice distortion, rough surface, and sharp edge transformation inevitably occurr in the resultant samples. In this work, an additional annealing process is proposed that aims at regulating lattice distortion as well as achieving round and smoother morphologies without any structural or elemental modifications. Such a structural enhancement is favored for improved lithium diffusion and electrochemical stability during cycling. Consequently, the annealed cathodes demonstrate a considerable enhancement in capacity retention, escalating from 68.7% to 91.9% after 100 cycles at 1 C. Additionally, the specific capacity is significantly increased from 64 to 142 mAh g-1 at 5 C when compared to the unannealed cathodes. This work offers a straightforward and effective approach for reinforcing the electrochemical properties of nickel-rich cathodes.

Lattice distortion-driven band gap engineering and enhanced electrocatalytic activity of Mn-substituted nanostructured SrTiO3 materials: A comprehensive investigation.

The lattice distortion and electrocatalytic activity are investigated by the mono-substituent of Mn with different concentrations to generate localized states in the electronic structure of SrTiO3. The sol-gel approach has been employed to fabricate SrTiO3 and SrTi1-xMnxO3 nanostructures (NSs). The structural analysis indicates Mn incorporation into Ti sites of SrTiO3, which shifts the lattice towards a higher diffraction angle with a single-phase cubic structure. The optical absorption spectra exhibit a decrease in band gap from 3.27 to 1.89 eV and reveal the shift in band edge positions towards the visible region. XPS analysis is carried out to confirm the formation of oxygen vacancies and valence band edge position. For SrTi0.88Mn0.12O3, OER and HER have the overpotential of 445 and 157 mV at a current density of 100 and 10 mA cm-2. Hence, the substitution of Mn (x = 0.12) into SrTiO3 lattice results in lattice distortion that enhances the electrochemical performance compared to SrTiO3. The current work manifestly established the optimal Mn composition (x = 0.12) in SrTiO3 lattice as desirable materials with defective valence states for required electrocatalytic redox potential as well as the acceleration of charge transfer kinetics towards water splitting applications.

Boosting Photocatalytic Nitrogen Fixation via Nanoarchitectonics Using Oxygen Vacancy Regulation in W-Doped Bi2MoO6 Nanosheets.

Ammonia and nitrates are key raw materials for various chemical and pharmaceutical industries. The conventional methods like Haber-Bosch and Ostwald methods used in the synthesis of ammonia and nitrates, respectively, result in harmful emission of gases. In recent years, the photocatalytic fixation of N2 into NH3 and nitrates has become a hot topic since it is a green and cost-effective approach. However, the simultaneous production of ammonia and nitrates has not been studied much. In this regard, we have synthesized W-doped Bi2MoO6 nanosheets in various molar ratios and demonstrated their potential as efficient photocatalysts for the simultaneous production of NH3 and NO3- ions under visible light irradiation. It was found that one of the catalysts (BMWO0.4) having an optimal molar ratio of doped tungsten showed the best photocatalytic NH3 production (56 µmol h-1) without using any sacrificial agents along with the simultaneous production of NO3- ions at a rate of 7 µmol h-1. The enhanced photocatalytic activity of the synthesized photocatalysts could be ascribed to oxygen vacancy defects caused by Mo substitution by a more electronegative W atom. Furthermore, density functional theory calculations verified the alteration in the band gap after doping of W atoms and also showed a strong chemisorption of N2 over the photocatalyst surface leading to its activation and thereby enhancing the photocatalytic activity. Thus, the present work provides insights into the effect of structural distortions on tailoring the efficiency of materials used in photocatalytic N2 fixation.

Interfacial Self-Assembly-Induced Lattice Distortion in Ti3C2 for Enhanced Piezocatalytic Activity.

Herein, self-assembled monolayers (SAMs) are constructed on the surface of Ti3C2 MXene to improve its environmental stability and piezocatalytic activity. Ti3C2/SAMs-X (X = H, Cl, and NH2) was prepared to enhance the piezocatalytic degradation of bisphenol A (BPA) and hydrogen production. Surface-treated Ti3C2 exhibits different lattice parameters and symmetry, thus leading to an increased polarization. The presence of polar functional groups in SAMs remarkably increases the surface potential of Ti3C2, thereby promoting the migration of piezoelectric electrons. Ti3C2/SAMs-NH2 exhibits the highest piezocatalytic performance, thus improving BPA removal and H2 generation by 7 and 1.8 times, respectively. In addition, Ti3C2/SAMs-NH2 remained stable under 100% relative humidity for 15 days. Therefore, it provides a facile strategy for modulating piezocatalytic properties through interfacial self-assembly-induced lattice distortion.