Passive sampling of high production volume chemicals and polycyclic aromatic hydrocarbons in urban atmospheres near petrochemical sites: Uptake rate determination and application.

This study describes the use of passive sampling followed by pressurised liquid extraction and gas chromatography-mass spectrometry for monitoring high production volume chemicals (HPVCs), such as benzothiazoles, benzesulfonamides, phthalate esters (PAEs), organophosphate esters, ultraviolet stabilizers, and phenolic antioxidants and polycyclic aromatic hydrocarbons (PAHs) in urban atmospheres close to a petrochemical area. To obtain accurate results when applying passive sampling, the uptake rates of each target compound for the sampling time applied must be known. Firstly, passive sampling was calibrated for two months and uptake rates of HPVCs and PAHs in an urban atmosphere determined using active sampling as the reference method. The obtained results showed experimental diffusive uptake rates between 1.6 m3 day-1 and 27 m3 day-1 for 32 of the target compounds that will allow enable cost-effective long-term monitoring campaigns of HPVCs to be performed. Secondly, the experimentally obtained uptake rates were used to monitor the concentrations of HPVCs and PAHs at six urban sampling sites close to the two petrochemicals parks in Tarragona (Spain) during a period the two months. Regardless of the sampling campaign, PAEs and PAHs were the families of compounds found at the highest concentration levels, with a sum of their mean values of 23 ng m-3 and 20 ng m-3, respectively.

On-site evaluation of DGT passive sampling for quantitatively measuring per- and polyfluoroalkyl substances in a river-estuary-sea water system.

The passive sampling technique of diffusive gradients in thin-films (DGT) is promising for monitoring emerging contaminants such as per- and polyfluoroalkyl substances (PFAS). It is urgent to evaluate the impacts of salinity and exposure time on DGT sampling before it can be set as a standard method. Herein, DGT sampler based on the binding gel of weak anion exchanger (WAX) resin was deployed in a representative water system of the Xiaoqing river-estuary-sea for representative sampling windows (<1 day to 28 days) with high pH (8.18 ± 0.04 to 8.51 ± 0.17) and wide ranges of salinity (0.95 ± 0.07‰ to 14.37 ± 3.92‰), total dissolved solids (1.20 ± 0.09 g/L to 15.29 ± 3.91 g/L) and dissolved organic matter (2.8-32 mg/L). The results showed that the WAX-DGT sampler exhibited good performance for most target PFAS except for short-chain perfluorocarboxylates (C ≤ 5) in 14 days. When the exposure time was over 14 days, biofouling of the sampler may deflect the mass accumulation of the PFAS in the sampler. Salinity played an important role in the mass binding of PFAS by DGT. The shorter the carbon chain of the compound, the greater the influence of the salinity. PFAS with carboxyl groups had greater affinities for the biofouled membrane filter than those with sulfonic groups. In the river-estuary-sea system, where PFAS concentrations changed dynamically, the temporal resolution of the monitoring strategy has been demonstrated to be more important than spatial resolution. DGT provided a better integral of PFAS exposure than grab sampling in the dynamic water system and offered equivalent sensitivity of grab sampling with exposure time <10 d and greater sensitivity with exposure time ≥10 d. Thus, DGT has the advantage of providing high temporal resolution monitoring. This study provided support for the standardization of the DGT technique.

Modelling passive sampling of hydrophilic compounds under time-variable aqueous concentrations.

Passive sampling is a crucial method for evaluating concentrations of hydrophilic organic compounds in the aquatic environment, but it is insufficiently understood to what extent passive samplers capture the intermittent emissions that frequently occur for this group of compounds. In the present study, silicone sheets and styrene-divinyl benzene-reversed phase sulfonated extraction disks with and without a polyethersulfone membrane were exposed under semi-field conditions in a 31 m3 flume at three different flow velocities. Natural processes and spiking/dilution measures caused aqueous concentrations to vary strongly with time. The data were analyzed using two analytical models that account for these time-variable concentrations: a sampling rate model and a diffusion model. The diffusion model generally gave a better fit of the data than the sampling rate model, but the difference in residual errors was quite small (median errors of 19 vs. 25% for silicone and 22 vs. 25% for SDB-RPS samplers). The sampling rate model was therefore adequate enough to evaluate the time-integrative capabilities of the samplers. Sampler performance was best for SDB-RPS samplers with a polyethersulfone membrane, despite the occurrence of lag times for some compounds (0.1 to 0.4 days). Sampling rates for this design also spanned a narrower range (80 to 110 mL/day) than SDB-RPS samplers without a membrane (100 to 660 mL/day). The effect of biofouling was similar for all compounds and was consistent with a biofouling layer thickness of 150 µm.

From capture to detection: A critical review of passive sampling techniques for pathogen surveillance in water and wastewater.

Water quality, critical for human survival and well-being, necessitates rigorous control to mitigate contamination risks, particularly from pathogens amid expanding urbanization. Consequently, the necessity to maintain the microbiological safety of water supplies demands effective surveillance strategies, reliant on the collection of representative samples and precise measurement of contaminants. This review critically examines the advancements of passive sampling techniques for monitoring pathogens in various water systems, including wastewater, freshwater, and seawater. We explore the evolution from conventional materials to innovative adsorbents for pathogen capture and the shift from culture-based to molecular detection methods, underscoring the adaptation of this field to global health challenges. The comparison highlights passive sampling's efficacy over conventional techniques like grab sampling and its potential to overcome existing sampling challenges through the use of innovative materials such as granular activated carbon, thermoplastics, and polymer membranes. By critically evaluating the literature, this work identifies standardization gaps and proposes future research directions to augment passive sampling's efficiency, specificity, and utility in environmental and public health surveillance.

An alternative silicone-based passive sampling device to derive organotin concentrations in the aqueous phase.

Organotin compounds (OTs) are well studied in various environmental compartments, with a critical focus on the water column as their primary entry point into aquatic ecosystems. In this context, a method for the analysis of organotin (OTs) in water using silicone rubber-based passive sampling was optimized, validated, and field-tested. Validation covered crucial parameters, including the limit of detection (LOD), limit of quantification (LOQ), accuracy, precision, linearity, and matrix effect. The method was shown to be robust (R2 ≥ 0.99), with recoveries between 70.2 and 114.6%, and precise (CV < 12.8%) (N = 3). LODCw and LOQCw were ≤15 and ≤ 48 pg Sn L-1, respectively, for TBT and TPhT. The matrix effect showed to be low (>-20% ME < 20%) for all OTs but TPhT (69.4%). The silicone rubber-water partition coefficients (Log Ksr,w) were estimated at 3.37 for MBT, 3.77 for DBT, 4.17 for TBT, 3.49 for MPhT, 3.83 for DPhT, and 4.22 for TPhT. During the field study carried out between October 2021 and February 2022 at the entrance of the Port of Santos navigation channel (Southeastern Brazil), sampling rates ranged between 4.1 and 4.6 L d-1, and the equilibrium was achieved for MBT, DBT, MPhT, and DPhT after ∼45 days of deployment. The freely dissolved concentrations varied between 134 and 165 pg Sn L-1 for TBT, 388 and 610 pg Sn L-1 for DBT, and 1114 and 1509 pg Sn L-1 for MBT, while MPhT, DPhT, and TPhT were below the limit of detection. Results pointed out that J-FLEX® rubber-based passive sampling is a suitable and reliable alternative method for the continuous monitoring of OTs in the water column.

Surface water monitoring of chemicals associated with animal husbandry in an agricultural region in the Netherlands using passive sampling.

Compounds originating from animal husbandry can pollute surface water through the application of manure to soil. Typically, grab sampling is employed to detect these residues, which only provides information on the concentration at the time of sampling. To better understand the emission patterns of these compounds, we utilized passive samplers in surface water to collect data at eight locations in a Dutch agricultural region, during different time intervals. As a passive sampler, we chose the integrative-based Speedisk® hydrophilic DVB. In total, we targeted 46 compounds, among which 25 antibiotics, three hormones, nine antiparasitics, and nine disinfectants. From these 46 compounds, 22 compounds accumulated in passive samplers in amounts above the limit of quantification in at least one sampling location. Over the 12-week deployment period, a time integrative uptake pattern was identified in 53% of the examined cases, with the remaining 47% not displaying this behavior. The occurrences without this behavior were primarily associated with specific location, particularly the most upstream location, or specific compounds. Our findings suggest that the proposed use of passive samplers, when compared in this limited context to traditional grab sampling, may provide enhanced efficiency and potentially enable the detection of a wider array of compounds. In fact, a number of compounds originating from animal husbandry activities were quantified for the first time in Dutch surface waters, such as flubendazole, florfenicol, and tilmicosine. The set-up of the sampling campaign also allowed to distinguish between different pollution levels during sampling intervals on the same location. This aspect gains particular significance when considering the utilization of different compounds on various occasions, hence, it has the potential to strengthen ongoing monitoring and mitigation efforts.

Potential Hazards of Polycyclic Aromatic Hydrocarbons in Great Lakes Tributaries Using Water Column and Porewater Passive Samplers and Sediment Equilibrium Partitioning.

The potential for polycyclic aromatic hydrocarbon (PAH)-related effects in benthic organisms is commonly estimated from organic carbon-normalized sediment concentrations based on equilibrium partitioning (EqP). Although this approach is useful for screening purposes, it may overestimate PAH bioavailability by orders of magnitude in some sediments, leading to inflated exposure estimates and potentially unnecessary remediation costs. Recently, passive samplers have been shown to provide an accurate assessment of the freely dissolved concentrations of PAHs, and thus their bioavailability and possible biological effects, in sediment porewater and overlying surface water. We used polyethylene passive sampling devices (PEDs) to measure freely dissolved porewater and water column PAH concentrations at 55 Great Lakes (USA/Canada) tributary locations. The potential for PAH-related biological effects using PED concentrations were estimated with multiple approaches by applying EqP, water quality guidelines, and pathway-based biological activity based on in vitro bioassay results from ToxCast. Results based on the PED-based exposure estimates were compared with EqP-derived exposure estimates for concurrently collected sediment samples. The results indicate a potential overestimation of bioavailable PAH concentrations by up to 960-fold using the EqP-based method compared with measurements using PEDs. Even so, PED-based exposure estimates indicate a high potential for PAH-related biological effects at 14 locations. Our findings provide an updated, weight-of-evidence-based site prioritization to help guide possible future monitoring and mitigation efforts. Environ Toxicol Chem 2024;43:1509-1523. © 2024 The Authors. Environmental Toxicology and Chemistry published by Wiley Periodicals LLC on behalf of SETAC.

Polyparameter Linear Free Energy Relationships for Partitioning of Neutral Organic Compounds to Storage Lipids.

Storage lipids are an important compartment in the bioaccumulation of neutral organic compounds. Reliable models for predicting storage lipid-water and storage lipid-air partition coefficients (Kislip/w and Kislip/a), as well as their temperature dependence, are considered useful. Polyparameter linear free energy relationships (PP-LFERs) are accurate, general, and mechanistically clear models for predicting partitioning-related physicochemical quantities. About a decade ago, PP-LFERs were calibrated for Kislip/w at the physiological temperature of 37 °C. However, to date, a comprehensive collection and sufficiently reliable PP-LFERs for Kislip/w and Kislip/a at the most common standard temperature of 25 °C are still lacking. In this study, experimentally based Kislip/w and/or Kislip/a values at 25 °C for 278 compounds were extensively collected or converted from the literature. Subsequently, PP-LFERs were calibrated for Kislip/w and Kislip/a at 25 °C, performing well over 10 orders of magnitude with root-mean-square errors of 0.17-0.21 log units for compounds with reliable descriptors. Furthermore, standard internal energy changes of transfer from water or air to storage lipids for 158 compounds were derived and used to calibrate PP-LFERs for estimating the temperature dependence of Kislip/w or Kislip/a. Additionally, using PP-LFERs, low-density polyethylene was confirmed to be a better storage lipid analogue than silicone and polyoxymethylene in the equilibrium passive sampling of nonpolar and H-bond acceptor polar compounds.

Characterization of fire investigators' polyaromatic hydrocarbon exposures using silicone wristbands.

BACKGROUND: Exposures to polyaromatic hydrocarbons (PAHs) contribute to cancer in the fire service. Fire investigators are involved in evaluations of post-fire scenes. In the US, it is estimated that there are up to 9000 fire investigators, compared to approximately 1.1 million total firefighting personnel. This exploratory study contributes initial evidence of PAH exposures sustained by this understudied group using worn silicone passive samplers. OBJECTIVES: Evaluate PAH exposures sustained by fire investigators at post-fire scenes using worn silicone passive samplers. Assess explanatory factors and health risks of PAH exposure at post-fire scenes. METHODS: As part of a cross-sectional study design, silicone wristbands were distributed to 16 North Carolina fire investigators, including eight public, seven private, and one public and private. Wristbands were worn during 46 post-fire scene investigations. Fire investigators completed pre- and post-surveys providing sociodemographic, occupational, and post-fire scene characteristics. Solvent extracts from wristbands were analyzed via gas chromatography-mass spectrometry (GC-MS). Results were used to estimate vapor-phase PAH concentration in the air at post-fire scenes. RESULTS: Fire investigations lasted an average of 148 minutes, standard deviation ± 93 minutes. A significant positive correlation (r=0.455, p<.001) was found between investigation duration and PAH concentrations on wristbands. Significantly greater time-normalized PAH exposures (p=0.039) were observed for investigations of newer post-fire scenes compared to older post-fire scenes. Regulatory airborne PAH exposure limits were exceeded in six investigations, based on exposure to estimated vapor-phase PAH concentrations in the air at post-fire scenes. DISCUSSION: Higher levels of off-gassing and suspended particulates at younger post-fire scenes may explain greater PAH exposure. Weaker correlations are found between wristband PAH concentration and investigation duration at older post-fire scenes, suggesting reduction of off-gassing PAHs over time. Exceedances of regulatory PAH limits indicate a need for protection against vapor-phase contaminants, especially at more recent post-fire scenes.

Efficient and practical in-jar silicone rubber based passive sampling for simultaneous monitoring of emerging fungicides in water and soils.

The occurrence and ecological impacts of emerging fungicides in the environment has gained increasing attention. This study applied an in-jar passive sampling device based on silicone rubber (SR) film to measuring the freely dissolved concentration (Cfree) of 6 current-use fungicides as a critical index of bioavailability in water and soils. The kinetics parameters including SR-water, soil-water, and organic carbon-water partition coefficients and sampling rates of the target fungicides were first attained and characterized well with their physicochemical properties. The in situ and ex situ field deployment in Hefei City provided the assessment of contaminated levels for these fungicides in rivers and soils. The Cfree of triadimefon and azoxystrobin was estimated at 0.54 ± 0.07-17.4 ± 2.5 ng L-1 in Nanfei River and Chao Lake, while triadimefon was only found in Dongpu Reservoir water with Cfree below 0.66 ± 0.04 ng L-1. The results exhibited that the equilibrium duration of 7 d was suitable for water application but a longer interval of 14 d was recommended for soil sampling. This work demonstrated the advantages of the proposed strategy in terms of fast monitoring within 2 weeks and high sensitivity down to detection limits in 0.5-5 ng L-1. The in-jar passive sampling device can be extrapolated to the evaluation for a wide coverage of organic pollutants in water and soils.

A High-Avidity, Thermostable, and Low-Cost Synthetic Capture for Ultrasensitive Detection and Quantification of Viral Antigens and Aerosols.

Lateral flow assays (LFAs) are currently the most popular point-of-care diagnostics, rapidly transforming disease diagnosis from expensive doctor checkups and laboratory-based tests to potential on-the-shelf commodities. Yet, their sensitive element, a monoclonal antibody, is expensive to formulate, and their long-term storage depends on refrigeration technology that cannot be met in resource-limited areas. In this work, LCB1 affibodies (antibody mimetic miniproteins) were conjugated to bovine serum albumin (BSA) to afford a high-avidity synthetic capture (LCB1-BSA) capable of detecting the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) spike protein and virus like particles (VLPs). Substituting the monoclonal antibody 2B04 for LCB1-BSA (stable up to 60 °C) significantly improved the thermal stability, shelf life, and affordability of plasmonic-fluor-based LFAs (p-LFAs). Furthermore, this substitution significantly improved the sensitivity of p-LFAs toward the spike protein and VLPs with precise quantitative ability over 2 and 3 orders of magnitude, respectively. LCB1-BSA sensors could detect VLPs at 100-fold lower concentrations, and this improvement, combined with their robust nature, enabled us to develop an aerosol sampling technology to detect aerosolized viral particles. Synthetic captures like LCB1-BSA can increase the ultrasensitivity, availability, sustainability, and long-term accuracy of LFAs while also decreasing their manufacturing costs.

Highly sensitive passive sampling of new pollutants in urban reclaimed water using hydrophilic-lipophilic balance sorbent-embedded cellulose acetate membrane.

Urban reclaimed water is important water resource in China, while the residual new pollutants in the water largely challenge their safety for further use. China's action program for the management of new pollutants (also known as emerging contaminants) requires effective method for monitoring diverse new pollutants in water. This work proposed a highly sensitive passive sampling method for monitoring diverse new pollutants in urban reclaimed water. Hydrophilic-lipophilic balance sorbent-embedded cellulose acetate membranes (HECAMs) were dynamically deployed in self-developed continuous flow integrative sampling device (CFISD) for sampling four types of new pollutants with wide polarity ranges (1.11 < log Kow < 9.49) in a reclaimed water network for landscape irrigation in Beijing, China. The estimated equilibrium partition ratios of most chemicals between HECAM and water were over 104, which would provide low detection limits. In the 7-d high-efficiency deployment, thirty new pollutants were detected, which indicated incompletely removal of various new pollutants in wastewater treatment process. The dynamical accumulation data were successfully fitted by first-order kinetic model and different contaminants reached different accumulation phases in the HECAMs during 7 d. Acceptable and steady uptake rate constants and sampling rates were obtained with the use of CFISD in field sampling. The estimated time-weighted average concentrations for contaminants had wide concentration range and were from 0.03 ng L-1 (pendimethalin) to 3,394 ng L-1 (dibutyl phthalate) and this may lead to environmental risk for further use the reclaimed water. Dynamical deployment results also provided sensitive information of concentration fluctuations and twelve pollutants showed concentration fluctuations during the sampling period. In summary, HECAM showed high sensitivities and credible performance of monitoring diverse new pollutants in the urban reclaimed water.

Comparison of active measurements, lichen biomonitoring, and passive sampling for atmospheric mercury monitoring.

The number of atmospheric mercury (Hg) monitoring stations is growing globally. However, there are still many regions and locations where Hg monitoring is limited or non-existent. Expansion of the atmospheric Hg monitoring network could be facilitated by the use of cost-effective monitoring methods. As such, biomonitoring and passive monitoring offer a unique alternative to well-established monitoring by active measurements, since they do not require a power supply and require minimal workload to operate. The use of biomonitoring (lichens and mosses) and passive air samplers (PASs) (various designs with synthetic materials) has been reported in the literature, and comparisons with active measurement methods have also been made. However, these studies compared either biomonitoring or PASs (not both) to only one type of active measurement. In our work, we used transplanted (7 sampling sites) and in situ lichens (8 sampling sites) for biomonitoring, two PASs from different producers (3 sampling sites), and two different active measurement types (continuous and discontinuous active measurements, 1 and 8 sampling sites, respectively) to evaluate their effectiveness as monitoring methods. In the 9-month sampling campaign, 3 sampling locations with different characteristics (unpolluted, vicinity of a cement plant, and vicinity of a former Hg mine) were used. The results obtained with lichens and PASs clearly distinguished between sampling locations with different Hg concentrations; using both PASs and lichens together increased the confidence of our observations. The present work shows that biomonitoring and passive sampling can be effectively used to identify areas with elevated atmospheric Hg concentrations. The same can be said for discontinuous active measurements; however, the discrepancy between atmospheric Hg concentrations derived from PASs and discontinuous active measurements should be further investigated in the future.

Trace elements fractionation in anaerobic digestates: Recommendation for using diffusive gradients in thin films passive samplers.

This study proposes an evaluation of the Diffusive Gradients in Thin films (DGT) technique to assess the labile fraction of trace metals and metalloids in anaerobic digestates. Experiments were performed in presence and absence of air to determine whether maintaining anaerobic conditions is mandatory during DGT deployments. A theoretically expected linear accumulation profile was observed for Fe, Mn, Ni, Mo, and As(III) in a manure-derived digestate and for Mn in distillery waste-derived digestate, whereas Al and Cu were detected without a consistent trend over time. The DGT technique can thus be used to evaluate the labile fraction of some trace elements in these digestates. The labile fraction of some elements was shown to evolve over 72 h when deployments were performed in the presence of air. We thus strongly recommend to systematically perform time-series deployments to identify and consider only the elements with a linear accumulation trend and to maintain anaerobic conditions.

Investigation of organic micropollutant pollution in Izmit Bay: a comparative study of passive sampling and instantaneous sampling techniques.

In this study, we used a comprehensive array of sampling techniques to examine the pollution caused by organic micropollutants in Izmit Bay for the first time. Our methodology contains spot seawater sampling, semi-permeable membrane devices (SPMDs) passive samplers for time-weighted average (TWA), and sediment sampling for long-term pollution detection in Izmit Bay, together. Additionally, the analysis results obtained with these three sampling methods were compared in this study. Over the course of two seasons in 2020 and 2021, we deployed SPMDs for 21 days in the first season and for 30 days in the second season. This innovative approach allowed us to gather sea water samples and analyze them for the presence of polycyclic aromatic hydrocarbons (Σ15 PAHs), polychlorinated biphenyls (Σ7 PCBs), and organochlorine pesticides (Σ11 OCPs). Using SPMD-based passive sampling, we measured micropollutant concentrations: PAHs ranged from 1963 to 10342 pg/L in 2020 and 1338 to 6373 pg/L in 2021; PCBs from 17.46 to 61.90 pg/L in 2020 and 8.37 to 78.10 pg/L in 2021; and OCPs from 269.2 to 8868 pg/L in 2020 and 141.7 to 1662 pg/L in 2021. Our findings revealed parallels between the concentrations of PAHs, PCBs, and OCPs in both SPMDs and sediment samples, providing insights into the distribution patterns of these pollutants in the marine ecosystem. However, it is worth noting that due to limited data acquisition, the suitability of spot sampling in comparison to instantaneous sampling remains inconclusive, highlighting the need for further investigation and data collection.

Mapping elemental solutes at sub-picogram levels during aqueous corrosion of Al alloys using diffusive gradients in thin films (DGT) with LA-ICP-MS.

A novel approach using diffusive gradients in thin films (DGT) with laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) for two-dimensional mapping of elemental solute release at sub-picogram levels during aqueous corrosion of Al alloys is presented. Evaluation of different DGT gels with mixed micro-sized binding phases (polyacrylamide-Chelex-Metsorb, polyurethane (PU)-Chelex-Metsorb, PU-Chelex-Zr(OH)4) demonstrated the superior performance of PU gels due to their tear-proof handling, low shrinkage, and compliance with green chemistry. DGT devices containing PU-Chelex-Zr(OH)4 gels, which have not been characterized for Al sampling before, showed quantitative uptake of Al, Zn, and Cu solutes over time (t = 4-48 h) with higher Al capacity (ΓDGT = 6.25 µg cm-2) than different gels. Application of PU-Chelex-Zr(OH)4 gels on a high-strength Al-Cu alloy (Al2219) exposed to NaCl (w = 1.5%, pH = 4.5, T = 21 °C) for 15 min in a novel piston-type configuration revealed reproducible patterns of Al and Zn co-solubilization with a spatial expansion ranging between 50 and 1000 µm. This observation, together with complementary solid-state data from secondary electron microscopy with energy-dispersive X-ray spectroscopy, showed the presence of localized pitting corrosion at the material surface. Detection limits for total solute masses of Al, Zn, and Cu were ≤0.72 pg, ≤8.38 pg, and ≤0.12 pg, respectively, for an area of 0.01 mm2, demonstrating the method's unique capability to localize and quantify corrosion processes at ultra-trace levels and high resolution. Our study advances the assessment of Al alloy degradation in aqueous environments, supporting the design of corrosion-resistant materials for fostering technological safety and sustainability.

Occurrence, Spatial Distribution, and Bioaccumulation of Dissolved Synthetic Musks in Freshwaters across China.

Commercial chemicals, such as synthetic musks, are of global concern, but data on their occurrence and spatial distribution in aquatic environments of large scale are scarce. Two sampling campaigns were conducted in the present study to measure freely dissolved synthetic musks in freshwaters across China using passive samplers, along with biological coexposure at selected sites. Polycyclic musks (PCMs) dominated synthetic musks, with a detection frequency of 95%. Higher concentrations of PCMs were observed in densely populated Mid, East, and South China compared to less populated regions, indicating the significance of anthropogenic activities for synthetic musks in water. The concentration ratios of galaxolide (HHCB)/tonalide (AHTN) were significantly higher in low-latitude areas than in high-latitude areas from June to September, suggesting that solar radiation played an important role in the degradation of HHCB/AHTN. Significant correlations were found between dissolved concentrations of HHCB and AHTN and their lipid-normalized concentrations in coexposed fish and clam. The estimated hazard quotients for HHCB and AHTN in freshwater fish consumed by humans were less than 0.01 at all sampling sites except the Yangtze River Basin. These results help to understand the environmental fate and ecological risks of synthetic musks on a large geographical scale.

Higher trophic levels and species with poorer dispersal traits are more susceptible to habitat loss on island fragments.

Ongoing habitat loss and fragmentation caused by human activities represent one of the greatest causes of biodiversity loss. However, the effects of habitat loss and fragmentation are not felt equally among species. Here, we examined how habitat loss influenced the diversity and abundance of species from different trophic levels, with different traits, by taking advantage of an inadvertent experiment that created habitat islands from a once continuous forest via the creation of the Thousand Island Lake, a large reservoir in China. On 28 of these islands with more than a 9000-fold difference in their area (0.12-1154 ha), we sampled plants, herbivorous insects, and predatory insects using effort-controlled sampling and analyses. This allowed us to discern whether any observed differences in species diversity were due to passive sampling alone or to demographic effects that disproportionately influenced some species relative to others. We found that while most metrics of sampling effort-controlled diversity increased with island area, the strength of the effect was exacerbated for species in higher trophic levels. When we more explicitly examined differences in species composition among islands, we found that the pairwise difference in species composition among islands was dominated by species turnover but that nestedness increased with differences in island area, indicating that some species are more likely to be absent from smaller islands. Furthermore, by examining trends of several dispersal-related traits of species, we found that species with lower dispersal propensity tended to be those that were lost from smaller islands, which was observed for herbivorous and predatory insects. Our results emphasize the importance of incorporating within-patch demographic effects, as well as the taxa and traits of species when understanding the influence of habitat loss on biodiversity.

Development of Nontargeted Workflow of Occupational Exposure by Infrared Ion Spectroscopy and Silicone Wristbands' Passive Sampling.

A new approach using orthogonal analytical techniques is developed for chemical identification. High resolution mass spectrometry and infrared ion spectroscopy are applied through a 5-level confidence paradigm to demonstrate the effectiveness of nontargeted workflow for the identification of hazardous organophosphates. Triphenyl phosphate is used as a surrogate organophosphate for occupational exposure, and silicone wristbands are used to represent personal samplers. Spectral data of a target compound is combined with spectral data of the sodium adduct and quantum chemical calculations to achieve a confirmed identification. Here, we demonstrate a nontargeted workflow that identifies organophosphate exposure and provides a mechanism for selecting validated methods for quantitative analyses.

Ongoing Laboratory Performance Study on Chemical Analysis of Hydrophobic and Hydrophilic Compounds in Three Aquatic Passive Samplers.

The quality of chemical analysis is an important aspect of passive sampling-based environmental assessments. The present study reports on a proficiency testing program for the chemical analysis of hydrophobic organic compounds in silicone and low-density polyethylene (LDPE) passive samplers and hydrophilic compounds in polar organic chemical integrative samplers. The median between-laboratory coefficients of variation (CVs) of hydrophobic compound concentrations in the polymer phase were 33% (silicone) and 38% (LDPE), similar to the CVs obtained in four earlier rounds of this program. The median CV over all rounds was 32%. Much higher variabilities were observed for hydrophilic compound concentrations in the sorbent: 50% for the untransformed data and a factor of 1.6 after log transformation. Limiting the data to the best performing laboratories did not result in less variability. Data quality for hydrophilic compounds was only weakly related to the use of structurally identical internal standards and was unrelated to the choice of extraction solvent and extraction time. Standard deviations of the aqueous concentration estimates for hydrophobic compound sampling by the best performing laboratories were 0.21 log units for silicone and 0.27 log units for LDPE (factors of 1.6 to 1.9). The implications are that proficiency testing programs may give more realistic estimates of uncertainties in chemical analysis than within-laboratory quality control programs and that these high uncertainties should be taken into account in environmental assessments.