Versatile Light-Mediated Synthesis of Degradable Bottlebrush Polymers Using α-Lipoic Acid.

Bottlebrush polymers have a variety of useful properties including a high entanglement molecular weight, low Young's modulus, and rapid kinetics for self-assembly. However, the translation of bottlebrushes to real-world applications is limited by complex, multi-step synthetic pathways and polymerization reactions that rely on air-sensitive catalysts. Additionally, most bottlebrushes are non-degradable. Herein, we report an inexpensive, versatile, and simple approach to synthesize degradable bottlebrush polymers under mild reaction conditions. Our approach relies on the "grafting-through" polymerization of α-lipoic acid (LA)-functionalized macromonomers. These macromonomers can be polymerized under mild, catalyst-free conditions, and due to reversibility of the disulfide bond in LA, the resulting bottlebrush polymers can be depolymerized by cleaving disulfide backbone bonds. Bottlebrushes with various side-chain chemistries can be prepared through the atom transfer radical polymerization (ATRP) of LA-functionalized macromonomers, and the backbone length is governed by the macromonomer molecular weight and solvent polarity. We also demonstrate that LA-functionalized macromonomers can be copolymerized with acrylates to form degradable bottlebrush networks. This work demonstrates the preparation of degradable bottlebrush polymers with a variety of side-chain chemistries and provides insight into the light-mediated grafting-through polymerization of dithiolane-functionalized macromonomers.

New powder reuse schema in laser-based powder bed fusion of polymers.

The laser-based powder bed fusion of polymers (PBF-LB/P) process often utilizes a blend of powders with varying degrees of degradation. Specifically, for polyamide 12, the traditional reuse schema involves mixing post-processed powder with virgin powder at a predetermined ratio before reintroducing it to the process. Given that only about 15% of the powder is utilized in part production, and powders are refreshed in equal proportions, there arises a challenge with the incremental accumulation of material across build cycles. To mitigate the consumption of fresh powder relative to the actual material usage, this study introduces the incorporation of recycled material into the PBF-LB/P process. This new powder reuse schema is presented for the first time, focusing on the laser sintering process. The characteristics of the recycled powder were evaluated through scanning electron microscopy, differential scanning calorimetry, X-ray diffraction, particle size distribution, and dynamic powder flowability assessments. The findings reveal that waste powders can be effectively reused in PBF-LB/P to produce components with satisfactory mechanical properties, porosity levels, dimensional accuracy, and surface quality.

First evidence of plastics in coypu (Myocastor coypus)'s platforms.

Platforms are structures built by coypus for various purposes, such as reproduction, resting, and thermoregulation. In a coastal wetland of central Italy, during a study aimed at investigating the characteristics of coypu's platforms, it was recorded, for the first time worldwide, the presence of plastic in these structures. Through a transect survey, we censused 83 platforms, among which three (3.61%) were found with presence of macro- and megaplastics (polystyrene, polypropylene, and low-density polyethylene in film form; polyester, polyamide, and expanded polystyrene in fragments). Through the FTIR spectra, it was possible to highlight the degradation of the polymeric materials. To stimulate possible in-depth investigations at the level of the food chain (e.g., coypu predators, including canids) in wet habitats, we discussed possible causes and implications of plastic presence in coypus' nest structures.

Towards in vitro - In vivo correlation models for in situ forming drug implants.

In vitro-In vivo correlation (IVIVC) is a main focus of the pharmaceutical industry, academia and the regulatory sectors, as this is an effective modelling tool to predict drug product in vivo performance based on in vitro release data and serve as a surrogate for bioequivalence studies, significantly reducing the need for clinical studies. Till now, IVIVCs have not been successfully developed for in situ forming implants due to the significantly different in vitro and in vivo drug release profiles that are typically achieved for these dosage forms. This is not unexpected considering the unique complexity of the drug release mechanisms of these products. Using risperidone in situ forming implants as a model, the current work focuses on: 1) identification of critical attributes of in vitro release testing methods that may contribute to differences in in vitro and in vivo drug release from in situ forming implants; and 2) optimization of the in vitro release method, with the aim of developing Level A IVIVCs for risperidone implants. Dissolution methods based on a novel Teflon shape controlling adapter along with a water non-dissolvable glass fiber membrane (GF/F) instead of a water dissolvable PVA film (named as GF/F-Teflon adapter and PVA-Teflon adapter, respectively), and an in-house fabricated Glass slide adapter were used to investigate the impact of: the surface-to-volume ratio, water uptake ratio, phase separation rate (measured by NMP release in 24 h post injection in vitro or in vivo), and mechanical pressure on the drug release patterns. The surface-to-volume ratio and water uptake were shown to be more critical in vitro release testing method attributes compared to the phase separation rate and mechanical pressure. The Glass slide adapter-based dissolution method, which allowed for the formation of depots with bio-mimicking surface-to-volume ratios and sufficient water uptake, has the ability to generate bio-relevant degradation profiles as well as in vitro release profiles for risperidone implants. For the first time, a Level A IVIVC (rabbit model) has been successfully developed for in situ forming implants. Release data for implant formulations with slightly different PLGA molecular weights (MWs) were used to develop the IVIVC. The predictability of the model passed external validation using the reference listed drug (RLD), Perseris®. IVIVC could not be developed when formulations with different PLGA molar ratios of lactic acid to glycolic acid (L/G) were included. The present work provides a comprehensive understanding of the impact of the testing method attributes on drug release from in situ forming implants, which is a valuable practice for level A IVIVC development.

Mechanochemical Backbone Editing for Controlled Degradation of Vinyl Polymers.

The chemically inert nature of fully saturated hydrocarbon backbones endows vinyl polymers with desirable durability, but it also leads to their significant environmental persistence. Enhancing the sustainability of these materials requires a pivotal yet challenging shift: transforming the inert backbone into one that is degradable. Here, we present a versatile platform for mechanochemically editing the fully saturated backbone of vinyl polymers towards degradable polymer chains by integrating cyclobutene-fused succinimide (CBS) units along backbone through photo-iniferter reversible addition-fragmentation chain-transfer (RAFT) copolymerization. Significantly, the evenly insertion of CBS units does not compromise thermal or chemical stability but rather offers a means to adjust the properties of polymethylacrylate (PMA). Meanwhile, reactive acyclic imide units can be selectively introduced to the backbone through mechanochemical activation (pulse ultrasonication or ball-milling grinding) when required. Subsequent hydrolysis of the acyclic imide groups enables efficient degradation, yielding telechelic oligomers. This approach holds promise for inspiring the design and modification of more environmentally friendly vinyl polymers through backbone editing.

Influence of Polymeric Microparticle Size and Loading Concentration on 3D Printing Accuracy and Degradation Behavior of Composite Scaffolds.

Successful employment of 3D printing for delivery of therapeutic biomolecules requires protection of their bioactivity on exposure to potentially inactivating conditions. Although intermediary encapsulation of the biomolecules in polymeric particulate delivery vehicles is a promising strategy for this objective, the inclusion of such particles in 3D printing formulations may critically impact the accuracy or precision of 3D printed scaffolds relative to their intended designed architectures, as well as the degradation behavior of both the scaffolds and the included particles. The present work aimed to elucidate the effect of poly(d,l-lactic-co-glycolic acid) particle size and loading concentration on material accuracy, machine precision, and degradation of 3D printed poly(ɛ-caprolactone)-based scaffolds. Using a main effects analysis, the sizes and loading concentrations of particle delivery vehicles investigated were found to have neither a beneficial nor disadvantageous influence on the metrics of printing quality such as material accuracy and machine precision. Meanwhile, particle loading concentration was determined to influence degradation rate, whereas printing temperature affected the trends in composite weight-average molecular weight. Neither of the two particle-related parameters (concentration nor diameter) was found to exhibit a significant effect on intra-fiber nor inter-fiber porosity. These findings evidence the capacity for controlled loading of particulate delivery vehicles in 3D printed scaffolds while preserving construct accuracy and precision, and with predictable dictation of composite degradation behavior for potential controlled release of encapsulated biomolecules.

How to Measure Polymer Degradation? An Analysis of Authors' Choices When Calculating the Carbonyl Index.

The carbonyl index aims to measure the degradation level and is used in plastic degradation research as a proxy for the general degradation level of collected plastic pieces. According to the choices for carbonyl index calculation, comparison using this index is prevented and must be unveiled by the authors, which does not always happen. In order to study the proper usage of the carbonyl index, regarding the choice of the reference band and the usage of the band intensity or the absorption area, we systematically reviewed the methodologies used for polypropylene as a case study. Based on 95 studies gathered from 2000 to 2024, two main methods were used to determine the carbonyl index: the ratio between the carbonyl band area and the reference band area (33.68%) and the ratio between the highest intensity of the carbonyl band and the reference band (66.31%). The reference band of choice and the type of calculation method produce different carbonyl index values for the same spectra and mean different information, preventing comparison among works with different calculations.

Comparative Analysis of the Effects of Incorporating Post-Industrial Recycled LLDPE and Post-Consumer PE in Films: Macrostructural and Microstructural Perspectives in the Packaging Industry.

In accordance with the Circular Economy Package of the European directive, the Spanish government compels manufacturers of plastic bags to include into their products a minimum of 70% of polyethylene (PE) waste. Following this mandate can be challenging and requires a deep knowledge of the alterations produced by the recycling in the main components of a plastic bag film: lineal low-density polyethylene (LLDPE), the LLDPE recycled post-industry, generated as waste from an industrial process (rLLDPE) and the PE recycled from post-consumer use (rPE), that has been picked up, cleaned, and reprocessed. This study provides insight in the macro and microstructural changes produced by several cycles of recycling in these materials. Specimens in the form of film for supermarket bags formed with these polymers have been subjected to several recycling sequences. The process closely mimics industrial processes. Four cycles have been applied to the samples. The evolution of mechanical properties, including tensile strength, elongation at break, and tear and impact tests, shows an obvious decrease due to degradation that is not an impediment for practical use after the four cycles of recycling according to the main specifications defined by the producer. Colorimetric measurements reveal no significant variations in the color of the films. The results of the FTIR and TGA analysis show degradation phenomena and changes in crystallinity in branching and the apparition of crosslinking that are in consonance with the mechanical data. There is also a difference between both types of recycled PE. In general, rLLDPE is more affected by the recycling than rPE. According to our findings, the limiting property would be the tearing. By comparing these values with bags available in the market, manufactured from 70-80% recycled material, we can infer that while two reprocessing cycles can lead to good results, a maximum of four cycles of recycling is advisable.

Evaluation of the in vivo chemical reactivity of a novel copolymer insulation on cardiac leads in a single-center study.

BACKGROUND: Human in vivo data on the chemical stability of different transvenous lead materials, particularly OptimTM leads, are lacking. OBJECTIVES: The purpose of this study was to determine the chemical reactivity of insulation materials by analyzing the molar mass of extracted pacing and defibrillator leads METHODS: We collected extracted leads at Emory University Hospitals and sent the leads with thermoplastic outer insulation material for molar mass analysis, a material characteristic that informs biostability. Leads were separated based on the chemical identity of the outer insulation material, and the molar mass was measured by an independent party. The extent of chemical reaction was compared across leads having different materials: poly(ether)urethane 55D, poly(ether)urethane 80A, and Optim. RESULTS: A total of 70 leads were extracted. The subset of extracted leads having outer insulation materials composed of PEU or Optim were analyzed for molar mass, where implant times ranged from 0.12 to 16.26 years. The rate of chemical degradation was compared by plotting the extent of reaction [Mn(t = 0)/Mn(t)] as a function of implant time. The Optim molar mass decreased to 40% of its initial value at 10 years of implant. No change in the molar mass of the PEU insulations could be resolved over the same 10-year implant time. CONCLUSION: Because the molar mass of a polymer is directly related to its mechanical integrity, the observed decrease in molar mass of Optim likely translates into premature insulation defects and is consistent with the observed increased rate of electrical malfunction/noise in this subset of cardiac leads.

Rubber Oxygenase Degradation Assay by UV-Labeling and Gel Permeation Chromatography.

A versatile and robust end-group derivatization approach using oximes has been developed for the detection of oxidative degradation of synthetic polyisoprenes and polybutadiene. This method demonstrates broad applicability, effectively monitoring degradation across a wide molecular weight range through ultraviolet (UV)-detection coupled to gel permeation chromatography. Importantly, it enables the effective monitoring of degradation via derivatization-induced UV-maximum shifts, even in the presence of an excess of undegraded polyene, overcoming limitations previously reported with refractive index detectors. Notably, this oxime-based derivatization methodology is used in enzymatic degradation experiments of synthetic polyisoprenes characterized by a cis: trans ratio with the rubber oxygenase LcpK30. It reveals substantial UV absorption in derivatized enzymatic degradation products of polyisoprene with molecular weights exceeding 1000 g mol-1 - an unprecedented revelation for this enzyme's activity on such synthetic polyisoprenes. This innovative approach holds promise as a valuable tool for advancing research into the degradation of synthetic polyisoprenes and polybutadiene, particularly under conditions of low organocatalytic or enzymatic degradation activity. With its broad applicability and capacity to reveal previously hidden degradation processes, it represents a noteworthy contribution to sustainable polymer chemistry.

Study of the Failure Mechanism of a High-Density Polyethylene Liner in a Type IV High-Pressure Storage Tank.

The use of Type IV cylinders for gas storage is becoming more widespread in various sectors, especially in transportation, owing to the lightweight nature of this type of cylinder, which is composed of a polymeric liner that exerts a barrier effect and an outer composite material shell that primarily imparts mechanical strength. In this work, the failure analysis of an HDPE liner in a Type IV cylinder for high-pressure storage was carried out. The breakdown occurred during a cyclic pressure test at room temperature and manifested in the hemispherical head area, as cracks perpendicular to the liner pinch-off line. The failed sample was thoroughly investigated and its characteristics were compared with those of other liners at different stages of production of a Type IV cylinder (blow molding, curing of the composite material). An examination of the liner showed that no significant chemical and morphological changes occurred during the production cycle of a Type IV cylinder that could justify the liner rupture, and that the most likely cause of failure was a design-related fatigue phenomenon.

Material matters: Degradation products affect regenerating Schwann cells.

Devices to treat peripheral nerve injury (PNI) must balance many considerations to effectively guide regenerating nerves across a gap and achieve functional recovery. To enhance efficacy, design features like luminal fillers have been explored extensively. Material choice for PNI devices is also critical, as the determining factor of device mechanics, and degradation rate and has increasingly been found to directly impact biological response. This study investigated the ways in which synthetic polymer materials impact the differentiation state and myelination potential of Schwann cells, peripheral nerve glia. Microporous substrates of polycaprolactone (PCL), poly(lactide-co-glycolide) (PLGA) 85:15, or PLGA 50:50 were chosen, as materials already used in nerve repair devices, representing a wide range of mechanics and degradation profiles. Schwann cells co-cultured with dorsal root ganglion (DRG) neurons on the substrates expressed more mature myelination proteins (MPZ) on PLGA substrates compared to PCL. Changes to myelination and differentiation state of glia were reflected in adhesion proteins expressed by glia, including ß-dystroglycan and integrin α6, both laminin binding proteins. Importantly, degradation products of the polymers affected glial expression independently of direct attachment. Fast degrading PLGA 50:50 substrates released measurable amounts of degradation products (lactic acid) within the culture period, which may push Schwann cells towards glycolytic metabolism, decreasing expression of early transcription factors like sox10. This study shows the importance of understanding not only material effects on attachment, but also on cellular metabolism which drives myelination responses.

Spectroscopic probing of ultraviolet-induced degradation in elastomeric polyurea.

Aromatic polyurea has garnered assiduous research due to its excellent impact, shock, abrasion, moisture, and chemical resistance properties. Polyurea can be used in protective coating and impact mitigation applications but is inevitably exposed to harsh deployment conditions such as extended ultraviolet (UV) radiation. Fourier Transform Infrared (FTIR) spectroscopy, Terahertz-time domain spectroscopy (THz-TDS), and Excitation-Emission Matrix spectroscopy (EEMS) deciphered the effects of UV radiation on radiated polyurea samples under ambient and nitrogen-rich conditions. Samples were radiated continuously for up to 15 weeks in increments of 3 weeks. Comprehensive FTIR analyses revealed a monotonic increase in disordered hydrogen bonding as a function of exposure duration in an ambient environment. Otherwise, marginal changes were observed in UV-radiated samples under nitrogen. The hydrogen bond length exhibited significant variations in the former compared to their nitrogen atmosphere counterparts. The results infer the nitrogen shielding effect, protecting polyurea from the photodegradation and photo-oxidation observed in samples radiated under the ambient atmosphere. THz-TDS spectra affirmed the FTIR results by probing changes in the complex refractive index. Terahertz spectral peaks associated with torsional vibrations of intermolecular hydrogen bonds in polyurea were notably correlated with increased exposure duration in the ambient atmosphere. Changes in the complex index as a function of exposure duration under nitrogen are minimal. The excitation-emission spectra of polyurea samples reveal a strong fluorescent behavior in 9-week and 12-week ambient-exposed polyurea due to cluster-triggered emission mechanisms. The results synthesized based on three different spectroscopy techniques paint a holistic portrait of the adverse effects of extended ultraviolet radiation of macromolecules deployed in harsh environmental conditions.

Influence of Rheological and Morphological Characteristics of Polyhydroxybutyrate on Its Meltblown Process Behavior.

Polyhydroxybutyrate (PHB) is a promising biopolymer. However, processing PHB in pure form in thermoplastic processes is limited due to its rapid degradation, very low initial crystallization rate, strong post-crystallization, and its low final stretchability. In this article, we screened commercial PHBs for morphological characteristics, rheological properties, and "performance" in the meltblown process in order to reveal process-relevant properties and overcome the shortcoming of PHB in thermoplastic processes for fiber formation. An evaluation of degradation (extruded (meltblown) material vs. granules) was performed via rheological and SEC analysis. The study revealed large differences in the minimum melt temperature (175 up to 200 °C) and the grade-dependent limitation of accessible throughput on a 500 mm plant. The average fiber diameter could be lowered from around 10 µm to 2.4 µm in median, which are the finest reported values in the literature so far. It was found that the determination of the necessary process temperature can be predicted well from the complex shear viscosity. Different to expectations, it became apparent that a broader initial molar mass distribution (>8) is suitable to overcome the state-of-the art limitations of PHAs in order to stabilize fiber formation, increase the productivity, and obtain better resistance towards thermal degradation in process. Accordingly, longer polymer chain fractions could be more affected by degradation than medium and short polymer chains in the distribution. Further, a low initial narrow distributed molar mass resulted in too brittle fabrics.

Interpretable Machine Learning Methods for Monitoring Polymer Degradation in Extrusion of Polylactic Acid.

This work investigates real-time monitoring of extrusion-induced degradation in different grades of PLA across a range of process conditions and machine set-ups. Data on machine settings together with in-process sensor data, including temperature, pressure, and near-infrared (NIR) spectra, are used as inputs to predict the molecular weight and mechanical properties of the product. Many soft sensor approaches based on complex spectral data are essentially 'black-box' in nature, which can limit industrial acceptability. Hence, the focus here is on identifying an optimal approach to developing interpretable models while achieving high predictive accuracy and robustness across different process settings. The performance of a Recursive Feature Elimination (RFE) approach was compared to more common dimension reduction and regression approaches including Partial Least Squares (PLS), iterative PLS (i-PLS), Principal Component Regression (PCR), ridge regression, Least Absolute Shrinkage and Selection Operator (LASSO), and Random Forest (RF). It is shown that for medical-grade PLA processed under moisture-controlled conditions, accurate prediction of molecular weight is possible over a wide range of process conditions and different machine settings (different nozzle types for downstream fibre spinning) with an RFE-RF algorithm. Similarly, for the prediction of yield stress, RFE-RF achieved excellent predictive performance, outperforming the other approaches in terms of simplicity, interpretability, and accuracy. The features selected by the RFE model provide important insights to the process. It was found that change in molecular weight was not an important factor affecting the mechanical properties of the PLA, which is primarily related to the pressure and temperature at the latter stages of the extrusion process. The temperature at the extruder exit was also the most important predictor of degradation of the polymer molecular weight, highlighting the importance of accurate melt temperature control in the process. RFE not only outperforms more established methods as a soft sensor method, but also has significant advantages in terms of computational efficiency, simplicity, and interpretability. RFE-based soft sensors are promising for better quality control in processing thermally sensitive polymers such as PLA, in particular demonstrating for the first time the ability to monitor molecular weight degradation during processing across various machine settings.

Impact of accelerated weathering on the leaching kinetics of stabiliser additives from microplastics.

The release of additives from microplastics is known to harm organisms. In the environment, microplastics are exposed to weathering processes which are suspected to influence additive leaching kinetics, the extent and mechanism of which remain poorly understood. We examined the impact of weathering on stabiliser additive leaching kinetics using environmentally relevant accelerated weathering and leaching procedures. Nine binary polymer-additive formulations were specifically prepared, weathered, analysed, and evaluated for their leaching characteristics. Cumulative additive release (Ce) varied widely between formulations, ranging from 0.009 to 1162 µg/g. Values of Ce generally increased by polymer type in the order polyethylene terephthalate < polyamide 6 < polyethylene. The change in leaching kinetics after accelerated weathering was incongruous across the nine formulations, with a significant change in Ce only observed for three out of nine formulations. Physicochemical characterisation of the microplastics demonstrated that additive blooming was the primary mechanism influencing the leaching response to weathering. These findings highlight the dependency of additive fate on the polymer type, additive chemistry, and the extent of weathering exposure. This has significant implications for risk assessment and mitigation, where the general assumption that polymer weathering increases additive leaching may be too simplistic.

Effects of polycaprolactone degradation products on the water flea, Daphnia magna: Carbodiimide additives have acute and chronic toxicity.

Plastics have benefited our lives in many ways, but their long persistence in the environment causes serious problems. Rapid decomposition and detoxification of plastics after use are significant challenges. As a possible solution, biodegradable plastics have attracted attention, and for environmental risk assessment research on polymer toxicity, use of indicator organisms, like water fleas and fish, has increased globally. However, such research often focuses on standardized substances without considering changes in toxicity due to plastic degradation products. Additionally, tests generally focus on acute toxicity, while long-term effects on organismal reproduction and lifespan are largely unknown. Understanding the impact of degraded polymers on biological activities is crucial for accurate risk assessment. In this study, we investigated the biological toxicity of substances generated during degradation of polycaprolactone (PCL), a common biodegradable plastic, using the indicator organism, Daphnia magna. We examined PCL, oligocaprolactones (OCLs), and monomers resulting from polymer cleavage, as well as carbodiimides, added during polyester synthesis. As a result, PCL, which is insoluble in water, reduced individual survival and total number of offspring at an exposure concentration of 100 mg/L, while no toxicity was observed for water-soluble degradation products, OCLs, and monomers. Furthermore, carbodiimides, which are expected to be released during PCL degradation, showed strong toxicity, significantly reducing individual survival and total number of offspring at 0.1-10 mg/L. These findings suggest that changes in physical properties due to polymer degradation and release of additives can significantly alter their toxicity.

Mass concentration and distribution characteristics of microplastics in landfill mineralized refuse using efficient quantitative detection based on Py-GC/MS.

Landfilling is the most traditional disposal method of domestic waste. Plastic waste in landfill sites could degrade to microplastics (MPs) and diffuse to the surrounding environment with leachate. However, MPs pollution in landfill mineralized refuse has not been well recognized. In the present research, a detection method for mixed MPs of polyethylene (PE), polypropylene (PP), and polystyrene (PS) based on Py-GC/MS was established and verified. The method is suitable for the rapid quantitative detection of large-batch of complex solid matrix samples, with an average deviation of less than 10%. Based on the method, samples from a landfill site in South China were studied, where PE was found to be the main component. The total concentration of MPs in mineralized refuse was 7.62 kg/t in the old area and 5.49 kg/t in the young area. Further analysis showed that the content of MPs was correlated with that of plastic waste and the landfill age, indicating that a considerable proportion was secondary MPs. The reserves of MPs in landfill sites may have reached an alarming number. In the absence of adequate safeguards, quantities of MPs may spread from the landfill sites, resulting in serious pollution of the surrounding soil and groundwater.

Synthesis of Degradable Polyolefins Bearing Disulfide Units via Metathesis Copolymerization.

Disulfide bonds are dynamic covalent bonds, which are easy to cleave and reform upon chemical stimulus. Various methods including the oxidative coupling of thiols and polymerization of disulfide-containing monomers have been developed for the synthesis of poly(disulfide)s. However, installing small amounts of disulfide units in the main chain of polyolefins has received much less attention. Herein, we report a novel strategy for incorporating cleavable disulfide units into the backbone of polyolefins using commercially available diallyl disulfide (DADS) as a comonomer via metathesis copolymerization. The copolymerization of diallyl disulfide with cyclooctene occurred using the second-generation Grubbs catalyst under mild conditions, allowing for the synthesis of copolymers with adjustable disulfide content ranging from 0.7 to 8.5 mol%, and the molecular weight of the obtained copolymers ranged from 5.8 kg·mol-1 to 42.8 kg·mol-1. The resulting polyolefins with disulfide insertion retained excellent thermal processability and exhibited degradability. Treatment of the copolymer (8.5 mol% disulfide content) with tri-n-butylphosphine resulted in a significant reduction in molecular weight from 5.8 kg·mol-1 to 1.6 kg·mol-1. Successful copolymerization with diallyl disulfide provides a convenient and effective method for obtaining degradable polyolefins.

Separation and Characterization of Plastic Waste Packaging Contaminated with Food Residues.

In this paper, we present the development of a novel processing technology to tackle hard-to-recycle plastic packaging waste contaminated with food residues. The proof-of-concept (POC) technology can effectively separate food residual amounts from plastic waste materials to a level acceptable for further re-use or recycling of the plastic packaging. To assess this technology, we have conducted spectroscopic, thermal, and calorimetric characterizations of the obtained fractions, such as cleaned mixed plastics (CMP), food waste with mixed plastics (FWMP), and a mixture of microplastics (MP). The analyses were carried out with the aid of Fourier-Transform Infrared spectroscopy (FT-IR), Thermo-Gravimetric Analysis (TGA), Microcone Combustion Calorimetry (MCC), and 'bomb' calorimetry. The highest ratio of CMP to FWMP and the lowest amount of MP were obtained utilizing 700 rpm blade rotational speed and 15 s residence time of contaminated plastics in a cutting mill chamber. The plastics were freed from food contamination by 93-97%, which highlights a strong potential of the POC as a solution for 'dry-cleaning' of similar wastes on a larger scale. The main components of the CMP fraction were low-density polyethylene (LDPE), polypropylene (PP), and polyethylene terephthalate (PET), which are recyclable plastics. The knowledge and understanding of thermal degradation behaviours and calorimetric attributes of separated fractions, determined in this study, are essential in informing the industrial players using pyrolysis as a technique for recycling plastics.