The characteristic smell emitted from two scale insects, Ceroplastes japonicus and Ceroplastes rubens.

The volatile components emitted from two scale insects, Ceroplastes japonicus and Ceroplastes rubens, were identified using GC-MS analysis. The major volatile components of the solvent extract from C. japonicus were α-humulene (35.8%) and δ-cadinene (17.0%), while those of C. rubens were ß-selinene (10.3%) and ß-elemene (5.1%). In GC/olfactometry, linalool, butyric acid, 3-methylbutyric acid, 2-methylbutyric acid, and vanillin were identified as the odor-active components of the extract from C. japonicus, in addition to trace amounts of trans-4,5-epoxy-(2E)-decenal, 4-methyl-(3E)-hexenoic acid, and phenylacetic acid. With regard to C. rubens, trans-4,5-epoxy-(2E)-decenal, 3-methylbutyric acid, and phenylacetic acid were identified as the odor-active components. Besides, decan-1,4-olide (γ-decalactone) with milky cherry-like note and 3-hydroxy-4,5-dimethylfuran-2(5H)-one (sotolone) with brown sugar-like note were also detected as the characteristic cherry-like sweet-and-sour note of these two scale insects. ABBREVIATIONS: GC: Gas chromatography; GC/O: gas chromatography/olfactometry.

Microbial electrosynthesis of butyrate from carbon dioxide: Production and extraction.

To date acetate is the main product of microbial electrosynthesis (MES) from carbon dioxide (CO2). In this work a tubular bioelectrochemical system was used to carry out MES and enhance butyrate production over the other organic products. Batch tests were performed at a fixed cathode potential of -0.8V vs SHE. The reproducibility of the results according to previous experiments was validated in a preliminary test. According to the literature butyrate production could take place by chain elongation reactions at low pH and high hydrogen partial pressure (pH2). During the experiment, CO2 supply was limited to build up pH2 and trigger the production of compounds with a higher degree of reduction. In test 1 butyrate became the predominant end-product, with a concentration of 59.7mMC versus 20.3mMC of acetate, but limitation on CO2 supply resulted in low product titers. CO2 limitation was relaxed in test 2 to increase the bioelectrochemical activity but increase pH2 and promote the production of butyrate, what resulted in the production of 87.5mMC of butyrate and 34.7mMC of acetate. The consumption of ethanol, and the presence of other products in the biocathode (i.e. caproate) suggested that butyrate production took place through chain elongation reactions, likely driven by Megasphaera sueciensis (>39% relative abundance). Extraction and concentration of butyrate was performed by liquid membrane extraction. A concentration phase with 252.4mMC of butyrate was obtained, increasing also butyrate/acetate ratio to 16.4. The results are promising for further research on expanding the product portfolio of MES.

Identification of bacteria using volatile organic compounds.

The rapid diagnosis of respiratory infections has always been an important goal for medical professionals, because rapid and accurate diagnosis leads to proper and timely treatment, and consequently, reduces the costs of incorrect and long-term treatments, and antibiotic resistance. The present study was conducted with the aim of detecting volatile organic compounds (VOCs) in three bacteria: Pseudomonas aeruginosa, Acinetobacter baumannii, Klebsiella pneumoniae. Headspace of the studied bacteria, after separately culturing in two types of liquid medium in three different time-periods, was extracted by solid phase microextraction and analysed by gas chromatography mass spectrometry The analysis results of the VOCs produced by the studied bacteria indicate that some VOCs are common and some are unique in each bacterium. 1-penten-3-ol, levomenthol, and 2-octyl-1-ol for P. aeruginosa, cyclohexene, 4-ethenyl, and cis-Dihydro-α-terpinyl acetate for A. baumannii and 1,3-butadiene, butyraldehyde, longifolene, octyl acetate, tridecanol, dodecenal, (E)-2-hexyl ester, butanoic acid, and 5,5-dodecadinyl-1 12-diol for K. pneumoniae were identified as unique VOCs for each bacterium. Finally, it can be said that an accurate and rapid bacterial detection method can be achieved by using a tool that can detect bacterial VOCs. However, more studies are needed to design a tool for which all aspects have been assessed, so that it can give us a more complete pattern for the use of these compounds as biomarkers.

Metabolic engineering of Clostridium tyrobutyricum for enhanced butyric acid production from glucose and xylose.

Clostridium tyrobutyricum is a promising microorganism for butyric acid production. However, its ability to utilize xylose, the second most abundant sugar found in lignocellulosic biomass, is severely impaired by glucose-mediated carbon catabolite repression (CCR). In this study, CCR in C. tyrobutyricum was eliminated by overexpressing three heterologous xylose catabolism genes (xylT, xylA and xlyB) cloned from C. acetobutylicum. Compared to the parental strain, the engineered strain Ct-pTBA produced more butyric acid (37.8g/L vs. 19.4g/L) from glucose and xylose simultaneously, at a higher xylose utilization rate (1.28g/L·h vs. 0.16g/L·h) and efficiency (94.3% vs. 13.8%), resulting in a higher butyrate productivity (0.53g/L·h vs. 0.26g/L·h) and yield (0.32g/g vs. 0.28g/g). When the initial total sugar concentration was ~120g/L, both glucose and xylose utilization rates increased with increasing their respective concentration or ratio in the co-substrates but the total sugar utilization rate remained almost unchanged in the fermentation at pH 6.0. Decreasing the pH to 5.0 significantly decreased sugar utilization rates and butyrate productivity, but the effect was more pronounced for xylose than glucose. The addition of benzyl viologen (BV) as an artificial electron carrier facilitated the re-assimilation of acetate and increased butyrate production to a final titer of 46.4g/L, yield of 0.43g/g sugar consumed, productivity of 0.87g/L·h, and acid purity of 98.3% in free-cell batch fermentation, which were the highest ever reported for butyric acid fermentation. The engineered strain with BV addition thus can provide an economical process for butyric acid production from lignocellulosic biomass.

[The volatile fatty acids in children with dysfunction of biliary tract].

The volatile fatty acids are metabolites of bacteria reflecting condition and disbiotic alterations of microflora of gastrointestinal tract. The study was carried out to determine qualitatively volatile fatty acids in saliva of children with dysfunction of biliary tract and healthy ones. The indices of volatile fatty acids were analyzed in 46 children aged 7-17 years and with dysfunction of biliary tract. The comparison group included 34 healthy children aged from 7 to 17 years. The gas-liquid chromatography was applied to qualitatively detect acetic, butyric, isovaleric acids (volatile fatty acids). The automatedgas chromatograph "Crystal deluxe 4000" with capillary column "HP-FFAP" and flame ionizing detector was used. The study established decreasing of anaerobic index, increasing of acetic, propionic acids and sum of volatile fatty acids in saliva of children of main group as opposed to children of comparison group. The possible role of bacterial metabolites and bacteria in pathogenesis of dysfunction of biliary tract in children. The description is made of one of possible mechanisms of increasing of volatile fatty acids in saliva under dysfunction of biliary tract. The integral indices of volatile fatty acids of saliva are the new additional criteria for diagnostic of dysfunction of biliary tract in children.

The use of high pressure CO2 -facilitated pH swings to enhance in situ product recovery of butyric acid in a two-phase partitioning bioreactor.

Through the use of high partial pressures of CO2 (pCO2 ) to facilitate temporary pH reductions in two-phase partitioning bioreactors (TPPBs), improved pH dependent partitioning of butyric acid was observed which achieved in situ product recovery (ISPR), alleviating end-product inhibition (EPI) during the production of butyric acid by Clostridium tyrobutyricum (ATCC 25755). Through high pressure pCO2 studies, media buffering effects were shown to be substantially overcome at 60 bar pCO2 , resulting in effective extraction of the organic acid by the absorptive polymer Pebax® 2533, yielding a distribution coefficient (D) of 2.4 ± 0.1 after 1 h of contact at this pressure. Importantly, it was also found that C. tyrobutyricum cultures were able to withstand 60 bar pCO2 for 1 h with no decrease in growth ability when returned to atmospheric pressure in batch reactors after several extraction cycles. A fed-batch reactor with cyclic high pCO2 polymer extraction recovered 92 g of butyric acid to produce a total of 213 g compared to 121 g generated in a control reactor. This recovery reduced EPI in the TPPB, resulting in both higher productivity (0.65 vs. 0.33 g L(-1) h(-1) ) and yield (0.54 vs. 0.40). Fortuitously, it was also found that repeated high pCO2 -facilitated polymer extractions of butyric acid during batch growth of C. tyrobutyricum lessened the need for pH control, and reduced base requirements by approximately 50%. Thus, high pCO2 -mediated absorptive polymer extraction presents a novel method for improving process performance in butyric acid fermentation, and this technique could be applied to the bioproduction of other organic acids as well.

Influence of the type of fiber coating and extraction time on foal dry-cured loin volatile compounds extracted by solid-phase microextraction (SPME).

Extraction of dry-cured loin volatile compounds by solid-phase microextraction (SPME) was optimized. Two different fiber coatings: carboxen/polydimethylsiloxane (CAR/PDMS) and divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS), and three extraction times (15, 30 and 45 min) were assayed. Between the fibers tested, CAR/PDMS coated fibers extracted between two and three times more total amount of volatile compounds than the DVD/CAR/PDMS coating (1314×10(6) vs. 526×10(6) area units). Fifty five compounds were extracted by the CAR/PDMS fiber, while only 48 of these were found with the DVB/CAR/PDMS fiber. On the other hand, 6 additional volatile compounds were extracted by the CAR/PDMS coating, all of them being of low molecular weight. Three of the major compounds extracted, hexanoic acid, methyl ester; butanoic acid, 3-methyl-, methyl ester and hexanal, were found in high proportion in both fiber coatings. The effect of exposure time was more marked for the DVD/CAR/PDMS fiber than for the CAR/PDMS coating. Fifteen minutes of extraction provided a volatile compounds profile with lower area counts for most compounds and significantly different to that obtained with 30 and 45 min of extraction. The extraction yields of dry-cured loin volatile compounds varied according to the fiber coating used and the time of exposure. Therefore, extraction conditions should be selected depending on the objective of the study. Finally, it can be concluded that both porous fibers tested, CAR/PDMS and DVB/CAR/PDMS, provide a similar volatile compounds profile for dry-cured foal loin.

Demonstration of in situ product recovery of butyric acid via CO2 -facilitated pH swings and medium development in two-phase partitioning bioreactors.

Production of organic acids in solid-liquid two-phase partitioning bioreactors (TPPBs) is challenging, and highly pH-dependent, as cell growth occurs near neutral pH, while acid sorption occurs only at low pH conditions. CO2 sparging was used to achieve acidic pH swings, facilitating undissociated organic acid uptake without generating osmotic stress inherent in traditional acid/base pH control. A modified cultivation medium was formulated to permit greater pH reduction by CO2 sparging (pH 4.8) compared to typical media (pH 5.3), while still possessing adequate nutrients for extensive cell growth. In situ product recovery (ISPR) of butyric acid (pKa = 4.8) produced by Clostridium tyrobutyricum was achieved through intermittent CO2 sparging while recycling reactor contents through a column packed with absorptive polymer Hytrel® 3078. This polymer was selected on the basis of its composition as a polyether copolymer, and the use of solubility parameters for predicting solute polymer affinity, and was found to have a partition coefficient for butyric acid of 3. Total polymeric extraction of 3.2 g butyric acid with no CO2 mediated pH swings was increased to 4.5 g via CO2 -facilitated pH shifting, despite the buffering capacity of butyric acid, which resists pH shifting. This work shows that CO2 -mediated pH swings have an observable positive effect on organic acid extraction, with improvements well over 150% under optimal conditions in early stage fermentation compared to CO2 -free controls, and this technique can be applied other organic acid fermentations to achieve or improve ISPR.

Butyric acid production from sugarcane bagasse hydrolysate by Clostridium tyrobutyricum immobilized in a fibrous-bed bioreactor.

A fermentation process using Clostridium tyrobutyricum immobilized in a fibrous-bed bioreactor (FBB) was developed for butyric acid production from sugarcane bagasse (SCB) hydrolysate. SCB was first treated with dilute acid and then hydrolyzed with cellulases. The hydrolysate containing glucose and xylose was used as carbon source for the fermentation without detoxification. The bacterium was able to grow at a specific growth rate of ∼0.06 h(-1) in media containing 15-20% (w/v) SCB in serum bottles. In batch cultures in the FBB, both glucose and xylose in the SCB hydrolysate were simultaneously converted to butyrate with a high yield (0.45-0.54 g/gsugar) and productivity (0.48-0.60 g/Lh). A final butyrate concentration of 20.9 g/L was obtained in a fed-batch culture, with an overall productivity of 0.51 g/Lh and butyrate yield of 0.48 g/g sugar consumed. This work demonstrated the feasibility of using SCB as a low-cost feedstock to produce butyric acid.

Extractive fermentation for butyric acid production from glucose by Clostridium tyrobutyricum.

A novel extractive fermentation for butyric acid production from glucose, using immobilized cells of Clostridium tyrobutyricum in a fibrous bed bioreactor, was developed by using 10% (v/v) Alamine 336 in oleyl alcohol as the extractant contained in a hollow-fiber membrane extractor for selective removal of butyric acid from the fermentation broth. The extractant was simultaneously regenerated by stripping with NaOH in a second membrane extractor. The fermentation pH was self-regulated by a balance between acid production and removal by extraction, and was kept at approximately pH 5.5 throughout the study. Compared with conventional fermentation, extractive fermentation resulted in a much higher product concentration (>300 g/L) and product purity (91%). It also resulted in higher reactor productivity (7.37 g/L. h) and butyric acid yield (0.45 g/g). Without on-line extraction to remove the acid products, at the optimal pH of 6.0, the final butyric acid concentration was only approximately 43.4 g/L, butyric acid yield was 0.423 g/g, and reactor productivity was 6.77 g/L. h. These values were much lower at pH 5.5: 20.4 g/L, 0.38 g/g, and 5.11 g/L. h, respectively. The improved performance for extractive fermentation can be attributed to the reduced product inhibition by selective removal of butyric acid from the fermentation broth. The solvent was found to be toxic to free cells in suspension, but not harmful to cells immobilized in the fibrous bed. The process was stable and provided consistent long-term performance for the entire 2-week period of study.

Identification and effects of interaction phytotoxic compounds from exudate of Cistus ladanifer leaves.

Eleven allelochemicals (ferulic acid, cinnamic acid, 4-hydroxybenzoic acid, hydroxycinnamic acid, methyl propionate, oxalic acid, methylmalonic acid, p-anisic acid, butyric acid, 3-hydroxybutyric acid, and azulene) were identified in the exudate of Cistus ladanifer L. We studied the effect of each on germination, cotyledon emergence, root length, and cotyledon length of Rumex crispus. Three groups were distinguished with respect to phytotoxic activity: compounds with low activity (ferulic acid, 4-hydroxybenzoic acid, oxalic acid, methylmalonic acid, p-anisic acid, hydroxybutyric acid, and azulene), with intermediate activity (cinnamic acid and hydroxycinnamic acid), and with high activity (methyl propionate and butyric acid). The effect of the interaction of the compounds was studied. When acting conjointly, all combinations tested produced a more negative effect on both germination and seedling growth than when acting alone. The interaction affected cotyledon emergence and root length more negatively than germination and cotyledon length. When hydroxycinnamic acid and cinnamic acid were added to these mixtures there was an enhancement in the phytotoxic activity, accentuating the effect of the other allelochemicals.

Small-scale characterization of wet powder masses suitable for extrusion-spheronization.

The method of compresso-rheology with an Instron 5567 was used for flow assessment of wet powder mass in order to improve its formulation. In our experiments, the method was efficient for selection of the excipient (Avicel CL611) able to improve the extrusion behavior of the high-dose wet powder mass. The method also allowed the determination of the minima and maxima of the wetting agent volume necessary to identify the correct moisture content for extrusion (20%). The results were not discriminative for the choice of the Avicel CL611 amount in the formulae even if an average amount necessary to improve extrudability of the active ingredient could have been estimated at about 10%. Nevertheless, this method appeared to be a rapid and easy small-scale method for studying wet powder mass, cause only a few grams of solids are required, this rheometer should prove useful in formulation research.