Determination of di-n-butyl adipate (DnBA) metabolites as possible biomarkers of exposure in human urine by online-SPE-LC-MS/MS.

Di-n-butyl adipate (DnBA) is an alternative to the anti-androgenic and strictly regulated di-n-butyl phthalate (DnBP) used as a cosmetic ingredient, plasticizer, and in various articles of everyday life. Hence, exposures of the general population have to be expected. Currently, biomarkers of DnBA exposure and methods for their determination are not available. Here, we describe a sensitive, rugged and precise analytical method for the determination of the DnBA monoester metabolite mono-n-butyl adipate (MnBA), as well as its potential downstream metabolites 3-hydroxy-mono-n-butyl adipate (3OH-MnBA) and 3-carboxy-mono-n-propyl adipate (3cx-MnPrA) in human urine. Glucuronic acid conjugates present in urine were deconjugated using a pure ß-glucuronidase. The metabolites were then analyzed by liquid chromatography on a C18 column with superficially porous particles coupled to electrospray ionization-triple quadrupole-tandem mass spectrometry, applying online turbulent flow chromatography for analyte enrichment and matrix depletion (online-SPE-LC-MS/MS). The metabolites were quantified using stable isotope dilution analysis with limits of quantification of 0.05 µg/L (MnBA), 0.1 µg/L (3OH-MnBA), and 0.5 µg/L (3cx-MnPrA). Method imprecision in urinary matrix was below 7% (coefficient of variation) for all analytes. Mean relative recoveries were between 93% and 107%. The suitability of the DnBA metabolites as biomarkers of exposure was demonstrated after dermal application of a commercially available sunscreen containing DnBA. Maximum concentrations were reached 6.5 h after dose (219 µg/L 3cx-MnPrA, 91 µg/L MnBA, and 3.9 µg/L 3OH-MnBA). Elimination kinetics were similar for all three metabolites. We were able to quantify 3cx-MnPrA and MnBA until 4 d after sunscreen application. In a sample set of 35 urine samples from the general German population, 3cx-MnPrA was quantified in 94% (median 2.54 µg/L, maximum 78.3 µg/L) and MnBA in 3% (median < LOQ, maximum 0.18 µg/L) of the samples. The method will be applied in future human metabolism and human biomonitoring population studies.

Universal response quantification approach using a Corona Charged Aerosol Detector (CAD) - Application on linear and cyclic oligomers extractable from polycondensate plastics polyesters, polyamides and polyarylsulfones.

In terms of risk assessment especially for known and unknown substances migrating from food contact materials, quantification without corresponding reference substances currently poses a challenge. In the present study, the opportunity of a universal response quantification approach was evaluated by using a corona charged aerosol detector (CAD) for liquid chromatography combined with inverse gradient compensation. Characteristics of CAD detection in dependence of substance properties were analyzed with 46 randomly chosen reference substances. An almost equal CAD response (±20%) was achieved for non-volatile substances with a molecular weight of minimum 400 g/mol and a vapor pressure of maximum 10-8 Torr. We empirically defined an analytical parameter, Q50/35, the quotient of CAD peak areas at CAD evaporator temperatures of 50 °C and 35 °C, to predict the adequacy of the CAD universal response approach for quantification of known and unknown analyte substances. Exemplarily, we applied the CAD universal quantification approach for the determination of extractable oligomers below 1000 g/mol from a variety of food contact polycondensate plastic materials (e.g. polyesters like polyethylene terephthalate, polybutylene terephthalate, Tritan copolyester, polyamides 6, 6.6 and 6 T/6I and polyarylsulfones polyphenylsulfone and polyethersulfone). Quantitative results for in total 44 oligomers out of 11 materials were compared with established material-specific quantification methods using extracted oligomer mixtures as well as individual oligomers isolated from the mixtures. CAD-based quantification results were generally in accordance to published quantification approaches for polyamide oligomers and oligomers from polyarylsulfones. For oligomers extracted and isolated from polyester materials a slight underestimation was determined by CAD universal response approach. In terms of detection limits and accuracy, the universal CAD approach exhibits no advantages compared to established UV-methods, to date.

Comparison of solidification of floating drop and homogenous liquid-liquid microextractions for the extraction of two plasticizers from the water kept in PET-bottles.

Two approaches based on solidification of floating drop microextraction (SFDME) and homogenous liquid-liquid microextraction (HLLE) were compared for the extraction and preconcentration of di-(2-ethylhexyl) phthalate (DEHP) and di-(2-ethylhexyl) adipate (DEHA) from the mineral water samples. In SFDME, a floated drop of the mixture of acetophenone/1-undecanol (1:8) was exposed on the surface of the aqueous solution and extraction was permitted to occur. In HLLE, a homogenous ternary solvent system was used by water/methanol/chloroform and the phase separation phenomenon occurred by salt addition. Under the optimal conditions, the LODs for the two target plasticizers (DEHA and DEHP), obtained by SFDME-GC-FID and HLLE-GC-FID, were ranged from 0.03 to 0.01 microg/L and 0.02 to 0.01 microg/L, respectively. HLLE provided higher preconcentration factors (472.5- and 551.2-fold) within the shorter extraction time as well as better RSDs (4.5-6.9%). While, in SFDME, high preconcentration factors in the range of 162-198 and good RSDs in the range of 5.2-9.6% were obtained. Both methods were applied for the analysis of two plasticizers in different water samples and two target plasticizers were found in the bottled mineral water after the expiring time and the boiling water was exposed to a polyethylene vial.

Determination of phthalates and adipate in physiological saline solutions by solid-phase microextraction and gas chromatography.

This study describes an analytical methodology developed for determination of phthalate esters (di-n-butyl, butylbenzyl and di-2-ethylhexyl phthalate) and adipate (di-n-ethylhexyl adipate) by solid-phase microextraction (SPME) and gas chromatography in normal saline solutions and, in bi-distilled water used to reconstitute medicines. An 85-microm-polyacrylate SPME fiber was selected and used in all analyses. The parameters affecting extraction efficiency were simultaneously optimized, firstly by means of a two-level full factorial design including a center point and subsequently through a Doehlert design for two-variables. Satisfactory detection limits in the range of 0.18 to 0.75 microg L(-1) and excellent precision, with relative standard deviation values being lower than 15.1% (n = 6), were obtained. Relative sensitivities of between 72.3 and 124.3% were obtained.

Determination of phthalates and adipate in bottled water by headspace solid-phase microextraction and gas chromatography/mass spectrometry.

The performance of three fibres for the headspace solid-phase microextraction (SPME) of di-2-ethylhexyl adipate (DEHA) and eight phthalates in water was investigated systematically under different extraction conditions. Good responses on the 65 microm polydimethylsiloxane/divinylbenzene (PDMS/DVB) SPME fibre were observed for DEHA and all phthalates. The polydimethylsiloxane (PDMS) SPME fibre had very poor responses for the lighter and slightly polar phthalates, dimethyl phthalate (DMP) and diethyl phthalate (DEP), while the divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS) SPME fibre had very poor responses for the heavier and non-polar adipate and phthalates. The salt (NaCl) was found to increase the partitioning of DMP, DEP, diisobutyl phthalate (DiBP), di-n-butyl phthalate, and benzyl butyl phthalate (BBP) from water into the headspace, while partitioning of heavier adipate and phthalates from water into headspace was suppressed when the concentration of NaCl was above 10%. The automated headspace SPME methods were developed and validated under two different salting conditions (30% NaCl for DMP, DEP and BBP, and 10% for DEHA, DiBP, DBP, di-n-hexyl phthalate (DHP), di-2-ethylhexyl phthalate (DEHP), and di-n-octyl phthalate (DOP)). Linearity with R(2) values better than 0.9949 was observed for DEHA and eight phthalates over the range from 0.1 to 20 microg L(-1). Method detection limits ranged from 0.003 microg L(-1) for DOP to 0.085 microg L(-1) for BBP. Good repeatability was observed for DEHA and most phthalates with relative standard deviation (RSD) values less than 10%. The methods were used to analyse bottled water samples for DEHA and eight phthalates. DMP, DHP, BBP, DEHA and DOP were not detected in any samples. Concentrations of the other phthalates were low (around sub-ppb) except for DBP in the water from a polycarbonate bottle at 1.72 microg L(-1).

Effect of surfactants on plasticizer biodegradation by Bacillus subtilis ATCC 6633.

The biodegradation of plasticizers has been previously shown to result in the accumulation of metabolites that are more toxic than the initial compound. The present work shows that the pattern of degradation of di-2-ethylhexyl adipate by Bacillus subtilis can be significantly altered by the presence of biosurfactants, such as surfactin, or synthetic surfactants, such as Pluronic L122. In particular, this work confirms that the monoester, mono-2-ethylhexyl adipate, is a metabolite in the breakdown of the plasticizer. This metabolite was proposed but not observed in earlier studies. Toxicity measurements showed it to be significantly more toxic than the plasticizer. Thus, the effect of the surfactants was to significantly increase the accumulation of one or both of the two most toxic metabolites; i.e., the monoester and 2-ethylhexanol. It was proposed that the most likely cause of the effect of the surfactants was the sequestering of these two metabolites into mixed micelles, resulting in their reduced availability for further degradation.

Preparation of horseradish peroxidase hydrazide and its use in immunoassay.

Preparation of horseradish peroxidase (HRP) hydrazide that is HRP linked to adipic acid dihydrazide (HRP-ADH) and its use in enzyme immunoassay (EIA) is described. In this new strategy, horseradish peroxidase was conjugated to adipic acid dihydrazide using a carbodiimide coupling method. The resulting HRP-ADH was then coupled to cortisol-21-hemisuccinate (Cortisol-21-HS) to prepare enzyme conjugate. The prepared cortisol-21-HS coupled ADH-HRP (Cortisol-21-HS-ADH-HRP) enzyme conjugate was used for the development of an enzyme linked immunosorbent assay (ELISA) for direct estimation of cortisol. To the cortisol antibody coated microtiter wells, standard or serum samples (50 microL), along with cortisol-21-HS-ADH-HRP enzyme conjugate (100 microL) were incubated for 1 h at 37 degrees C. Bound enzyme activity was measured by using tetramethyl benzidine/hydrogen peroxide (TMB/H2O2) as substrate. The sensitivity of the assay was 0.05 microg/dL and the analytical recovery ranged from 92.9 to 101.7%.

Benzene-free synthesis of adipic acid.

Strains of Escherichia coli were constructed and evaluated that synthesized cis,cis-muconic acid from D-glucose under fed-batch fermentor conditions. Chemical hydrogenation of the cis,cis-muconic acid in the resulting fermentation broth has also been examined. Biocatalytic synthesis of adipic acid from glucose eliminates two environmental concerns characteristic of industrial adipic acid manufacture: use of carcinogenic benzene and benzene-derived chemicals as feedstocks and generation of nitrous oxide as a byproduct of a nitric acid catalyzed oxidation. While alternative catalytic syntheses that eliminate the use of nitric acid have been developed, most continue to rely on petroleum-derived benzene as the ultimate feedstock. In this study, E. coli WN1/pWN2.248 was developed that synthesized 36.8 g/L of cis,cis-muconic acid in 22% (mol/mol) yield from glucose after 48 h of culturing under fed-batch fermentor conditions. Optimization of microbial cis,cis-muconic acid synthesis required expression of three enzymes not typically found in E. coli. Two copies of the Klebsiella pneumoniae aroZ gene encoding DHS dehydratase were inserted into the E. coli chromosome, while the K. pneumoniae aroY gene encoding PCA decarboxylase and the Acinetobacter calcoaceticus catA gene encoding catechol 1,2-dioxygenase were expressed from an extrachromosomal plasmid. After fed-batch culturing of WN1/pWN2.248 was complete, the cells were removed from the broth, which was treated with activated charcoal and subsequently filtered to remove soluble protein. Hydrogenation of the resulting solution with 10% Pt on carbon (5% mol/mol) at 3400 kPa of H2 pressure for 2.5 h at ambient temperature afforded a 97% (mol/mol) conversion of cis,cis-muconic acid into adipic acid.

Enzymatic formation, stability, and spontaneous reactions of 4-fluoromuconolactone, a metabolite of the bacterial degradation of 4-fluorobenzoate.

Enzymatic conversion of 4-fluorocatechol in the simultaneous presence of partially purified preparations of catechol 1,2-dioxygenase from Pseudomonas cepacia and muconate cycloisomerase from Alcaligenes eutrophus 335 yielded a product that was unambiguously identified as (+)-4-fluoromuconolactone [(+)-4-carboxymethyl-4-fluoro-but-2-en-4-olide]. This compound was shown to be the only major product formed from 3-fluoro-cis,cis-muconate by the action of muconate cycloisomerases from A. eutrophus 335, A. eutrophus JMP134, and P. cepacia as well as by the action of dichloromuconate cycloisomerase from A. eutrophus JMP134. This finding implies that dichloromuconate cycloisomerase, like the muconate cycloisomerases, catalyzes primarily a cycloisomerization reaction, which only in the case of chloro- and bromo-substituted substrates is connected to a dehalogenation. 4-Fluoromuconolactone at pH 7 decomposes by spontaneous reactions mainly to maleylacetate, which then decarboxylates to give cis-acetylacrylate. Although significant amounts of an unidentified compound are also formed from the fluorolactone, HF elimination to the two isomeric dienelactones (4-carboxymethylenebut-2-en-4-olides) is negligible. However, all spontaneous reactions proceed so slowly that an enzymatic conversion of 4-fluoromuconolactone must be assumed. Participation of dienelactone hydrolases in this reaction is indicated by their induction during growth of various strains with 4-fluorobenzoate. However, experiments with cell extracts of P. putida A3.12 suggest that at least one other hydrolytic enzyme is able to contribute to 4-fluoromuconolactone conversion. In light of these observations, earlier proposals for a 4-fluorobenzoate degradative pathway are discussed.

Chemistry of the collagen cross-links. Isolation and characterization of two intermediate intermolecular cross-links in collagen.

This paper describes the isolation from reduced collagen of two new amino acids believed to be involved, in their non-reduced form, as intermolecular cross-links stabilizing the collagen fibre. The reduction of intact collagen fibrils with tritiated sodium borohydride was found to stabilize the aldehyde-mediated cross-links to acid hydrolysis and thus allowed their location and isolation from acid hydrolysates on an automatic amino acid analyser. Comparison of the radioactive elution patterns from the autoanalyser of collagen treated in various ways before reduction permitted a preliminary classification of the peaks into cross-link precursors, intramolecular and intermolecular cross-links. The techniques employed to isolate the purified components on a large scale and to identify them structurally are described in detail. Two labile intermolecular cross-links were isolated in their reduced forms, one of which was identified by high-resolution mass spectrometry as N(in)-(5-amino-5-carboxypentyl)hydroxylysine. The structure of this compound was confirmed by chemical synthesis. The cross-link precursor alpha-aminoadipic delta-semialdehyde was isolated in its reduced form, in-hydroxynorleucine, together with its acid degradation product in-chloronorleucine. A relatively stable intermolecular cross-link was isolated and partially characterized by mass spectrometry as an aldol resulting from the reaction of the delta-semialdehyde derived from lysine and hydroxylysine.