Magnetic iron oxide nanoparticle enhanced microwave pretreatment for anaerobic digestion of meat industry sludge.

Our study investigates the effects of iron oxide (Fe3O4) nanoparticles combined microwave pretreatment on the anaerobic digestibility and soluble chemical oxygen demand (SCOD) of meat industry sludge. One of our main objectives was to see whether the different microwave-based pretreatment procedures can enhance biogas production by improving the biological availability of organic compounds. Results demonstrated that combining microwave irradiation with magnetic iron oxide nanoparticles considerably increased SCOD (enhancement ratio was above 1.5), the rate of specific biogas production, and the total cumulative specific biogas volume (more than a threefold increment), while having no negative effect on the biomethane content. Furthermore, the assessment of the sludge samples' dielectric properties (dielectric constant and loss factor measured at the frequency of 500 MHz) showed a strong correlation with SCOD changes (r = 0.9942, R2 = 0.99), offering a novel method to evaluate pretreatment efficiency.

Rice husk reuse as a sustainable energy alternative in Tolima, Colombia.

Colombia has great potential to produce clean energy through the use of residual biomass from the agricultural sector, such as residues obtained from the life cycle of rice production. This document presents a mixed approach methodology study to examine the combustion of rice husks as a possible energy alternative in the Tolima department of Colombia. First, the physicochemical characteristics of the rice husk were analyzed to characterize the raw material. Next, System Advisor Model (SAM) software was used to model a bioenergy plant to obtain biochar, bio-oil, and biogas from the combustion of rice husks and generate performance matrices, such as thermal efficiency, heat rate, and capacity factor. Then, the project was evaluated for financial feasibility using a mathematical model of net present value (NPV) with a planning horizon of 5 years. Finally, a subset of the local population was surveyed to assess perspectives on the project in the region. The results of the rice husk physicochemical analysis were the following: nitrogen content (0.74%), organic carbon (38.04%), silica (18.39%), humidity determination (7.68%), ash (19.4%), presence of carbonates (< 0.01%), and pH (6.41). These properties are adequate for the combustion process. The SAM simulation showed that the heat transferred in the boiler was 3180 kW, maintaining an efficiency between 50 and 52% throughout the 12 months of the year, meaning that the rice husk can generate electricity and thermal energy. The financial analysis showed that the internal rate of return (IRR) was 6% higher than the opportunity interest rate (OIR), demonstrating economic feasibility of the project. The design and creation of a rice husk processing plant is socially and environmentally viable and has the potential to contribute to the economic development of the Tolima community and reduce greenhouse gases. Likewise, this activity has the potential to promote energy security for consumers and environmental sustainability while at the same time being economically competitive.

Nutrients recovery from dairy wastewater by Chlorella vulgaris and comparison of the lipid's composition with various chlorella strains for biodiesel production.

Microalgae biomass is regarded as a promising feedstock for biodiesel production. The biomass lipid content and fatty acids composition are among the main selective criteria when screening microalgae strains for biodiesel production. In this study, three strains of Chlorella microalgae (C. kessleri, C. sorokiniana, C. vulgaris) were cultivated nutrient media with different nitrogen contents, and on a medium with the addition of dairy wastewater. Moreover, microalgae grown on dairy wastewater allowed the removal of azote and phosphorous. The removal efficiency of 90%, 53% and 95% of ammonium nitrogen, total nitrogen and phosphate ions, respectively, were reached. The efficiency of wastewater treatment from inorganic carbon was 55%, while the maximum growth of biomass was achieved. All four samples of microalgae had a similar fatty acid profile. Palmitic acid (C16:0) was the most abundant saturated fatty acid (SFA), and is suitable for the production of biodiesel. The main unsaturated fatty acids (UFA) present in the samples were oleic acid (C18:1 n9); linoleic acid (C18:2 n6) and alpha-linolenic acid (C18:3 n3), which belong to omega-9, omega-6, omega-3, respectively.

Greenhouse gas emissions from on-site sanitation systems: A systematic review and meta-analysis of emission rates, formation pathways and influencing factors.

Onsite sanitation systems (OSS) are significant sources of greenhouse gases (GHG) including carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O). While a handful of studies have been conducted on GHG emissions from OSS, systematic evaluation of literature on this subject is limited. Our systematic review and meta-analysis provides state-of-the- art information on GHG emissions from OSS and identifies novel areas for investigation. The paper analyzes GHG emission rates from different OSS, the influence of various design, operational, and environmental factors on emission rates and proffers mitigation measures. Following the Preferred Reporting Items for Systematic reviews and Meta-analysis (PRISMA) guidelines, we identified 16 articles which quantified GHG emissions from OSS. Septic tanks emit substantial amounts of CO2 and CH4 ranging from 1.74 to 398.30 g CO2/cap/day and 0.06-110.13 g CH4/cap/day, respectively, but have low N2O emissions (0.01-0.06 g N2O/cap/day). CH4 emissions from pit latrines range from 0.77 to 20.30 g CH4/cap/day N2O emissions range from 0.76 to 1.20 gN2O/cap/day. We observed statistically significant correlations (p < 0.05) between temperature, biochemical oxygen demand, chemical oxygen demand, dissolved oxygen, storage period, and GHG emissions from OSS. However, no significant correlation (p > 0.05) was observed between soil volumetric water content and CO2 emissions. CH4 emissions (expressed as CO2 equivalents) from OSS estimated following Intergovernmental Panel for Climate Change (IPCC) guidelines were found to be seven times lower (90.99 g CO2e/cap/day) than in-situ field emission measurements (704.7 g CO2e/cap/day), implying that relying solely on IPCC guidelines may lead to underestimation of GHG emission from OSS. Our findings underscore the importance of considering local contexts and environmental factors when estimating GHG emissions from OSS. Plausible mitigation measures for GHG emissions from OSS include converting waste to biogas in anaerobic systems (e.g. biogas), applying biochar, and implementing mitigation policies that equally address inequalities in sanitation service access. Future research on GHG from OSS should focus on in-situ measurements of GHGs from pit latrines and other common OSS in developing countries, understanding the fate and transport of dissolved organics like CH4 in OSS effluents and impacts of microbial communities in OSS on GHG emissions. Addressing these gaps will enable more holistic and effective management of GHG emissions from OSS.

The flow pattern effects of hydrodynamic cavitation on waste activated sludge digestibility.

The disintegration of raw sludge is of importance for enhancing biogas production and facilitates the degradation of substrates for microorganisms so that the efficiency of digestion can be increased. In this study, the effect of hydrodynamic cavitation (HC) as a pretreatment approach for waste activated sludge (WAS) was investigated at two upstream pressures (0.83 and 1.72 MPa) by using a milli-scale apparatus which makes sludge pass through an orifice with a restriction at the cross section of the flow. The HC probe made of polyether ether ketone (PEEK) material was tested using potassium iodide solution and it was made sure that cavitation occurred at the selected pressures. The analysis on chemical effects of HC bubbles collapse suggested that not only cavitation occurred at low upstream pressure, i.e., 0.83 MPa, but it also had high intensity at this pressure. The pretreatment results of HC implementation on WAS were also in agreement with the chemical characterization of HC collapse. Release of soluble organics and ammonium was observed in the treated samples, which proved the efficiency of the HC pretreatment. The methane production was improved during the digestion of the treated samples compared to the control one. The digestion of treated WAS sample at lower upstream pressure (0.83 MPa) resulted in higher methane production (128.4 mL CH4/g VS) compared to the treated sample at higher upstream pressure (119.1 mL CH4/g VS) and control sample (98.3 mL CH4/g VS). Thus, these results showed that the HC pretreatment for WAS led to a significant increase in methane production (up to 30.6%), which reveals the potential of HC in full-scale applications.

From grass to gas and beyond: Anaerobic digestion as a key enabling technology for a residual grass biorefinery.

Roadside grass clippings hold potential as a sustainable source of bioenergy as they do not compete with crops for land use, and are only partially utilized for low-value applications. In this study, we proposed using roadside grass as a sole feedstock for anaerobic digestion (AD) in three different settings, and assessed the potential of producing biomaterials and fertilizers from grass-based digestate. Wet continuous digestion at pilot scale and dry batch digestion at pilot and large scales resulted in biogas yields up to 700 Nm3.t-1 DOM with a methane content of 49-55 %. Despite promising results, wet AD had operational problems such as clogging and poor mixing; once upscaled, the dry digestion initially also presented an operational problem with acidification, which was overcome by the second trial. Digested grass fibers from the pilot dry AD were processed into biomaterials and performed similarly or better than the undigested fibers, while around 20 % performance reduction was observed when compared to reference wood fibers. A mass balance indicated reduced fiber recovery when higher biogas production was obtained. The liquid fraction from the pilot dry AD was characterized for its nutrient content and used as a biofertilizer in another study. In contrast, the leachate collected from the large-scale dry AD had a low nitrogen content and high chloride content that could hinder its further use. Finally, a regional market analysis was conducted showing that the biocomposites produced with the available grass fibers could substitute at least half of the current European market based on our results.

Early detection of deep-seated smouldering fires in wood waste storage using ERT.

Incidents of waste and biofuel fires are common at all stages of the waste recycling chain and have grave implications for business, employees, firefighters, society, and environment. An early detection of waste and biofuel fires in the smouldering stage could save precious lives, resources, and our environment. Existing fire detection methodologies e.g. handheld temperature sensors, IR cameras, gas sensors, and video and satellite-based monitoring techniques have inherent limitations to efficiently detect smouldering fires. An attempt was made to explore the potential of electrical resistivity tomography (ERT) as an alternate tool to address the problem. In the experiments an externally powered resistive wire was employed to initiate the smouldering fire inside the test material (wood pellets, wood shavings, wood fines). Time series of ERT that followed the initiation and development of smouldering were recorded using an automated monitoring instrument setup. The actual geometry of the experimental sample container and electrode setup was integrated in the 3D finite element method (FEM) model grid to perform inverse numerical modelling (inversion) and to develop resistivity tomographic images. The study shows a sharp increase in ratio of resistivity (R/Ro ≥ 50 %) in the test material in the region of smouldering hotspot and demonstrates the potential use of ERT technique for the detection of smouldering hotspots in silos and pile storage of organic material such as wood-based fuels, wood waste, coal, municipal solid waste (MSW), recyclables etc. More research is however required for enabling the use of this technique at the practical scale for different storage conditions.

Design expert based optimization of the pyrolysis process for the production of cattle dung bio-oil and properties characterization.

This study aimed to optimize pyrolysis conditions to maximize bio-oil yield from cattle dung, a waste product of livestock practices. Pyrolysis of cattle dung was carried out in batch type reactor. The pyrolysis process was optimized using a central composite design in response surface methodology, with conversion parameters such as pyrolysis temperature, vapor cooling temperature, residence time, and gas flow rate taken into account. The cattle dung bio-oil was analyzed using gas chromatography/mass spectroscopy (GC/MS), an elemental analyzer, a pH probe, and a bomb calorimeter. Furthermore, the ASTM standard procedures were used to determine the bio-fuel characteristics. The optimized conditions were found to be a pyrolysis temperature of 402 °C, a vapor cooling temperature of 2.25 °C, a residence time of 30.72 min, and a gas flow rate of 1.81 l min-1, resulting in a maximum bio-oil yield of 18.9%. According to the findings, the yield of bio-oil was predominantly affected by pyrolysis temperature and vapor cooling temperature. Moreover, the bio-oil that was retrieved was discovered to be similar to conventional liquid fuels in numerous ways.

Deep eutectic solvent pretreatment of cork dust - Effects on biomass composition, phenolic extraction and anaerobic degradability.

In this study, phenolic compounds using deep eutectic solvents (DES) were extracted from cork dust, and the biogas production potential of DES-treated cork dust samples was determined. The DES treatment was carried out using choline chloride and formic acid (1:2 M ratio) at various temperatures (90, 110 and 130 °C) and treatment times (20, 40 and 60 min) at a solid-to-solvent ratio of 1:10 g mL-1. The highest total phenolic content (137 mg gallic acid equivalent (GAE) g-1 dry cork dust) was achieved at 110 °C/20 min. The extracts exhibited an antioxidant capacity of up to 56.3 ± 3.1 % 1,1-diphenyl-2-picrylhydazyl (DPPH) inhibition at a dilution rate of 100. DES treatment resulted in minimal sugar solubilization at low temperatures, while approximately 42 % of the xylan fraction in the biomass degraded under severe conditions (e.g., 130 °C/60 min). Catechin, 4-hydroxybenzoic acid and gallic acid were the major phenolics in DES extracts. The biogas yield of DES-treated cork dust increased with treatment severity. The highest biogas yield (115.1mLN gVS-1) was observed at 130 °C/60 min, representing an increase of 125 % compared to the untreated sample. SEM images revealed that the surface structure of the samples became smoother after mild pretreatment and rougher after harsh pretreatment. Compositional and FTIR analyses indicated that a higher biogas formation potential was associated with increased cellulose content in the substrate, which could be attributed to hemicellulose solubilization in the hydrolysate. Overall, DES pretreatment effectively enhanced phenol extraction and anaerobic degradability.

Mechanism of improving anaerobic fermentation performance of kitchen waste pretreated by ionizing irradiation-part 1: rice.

Ionizing irradiation, as a new pretreatment method for the anaerobic fermentation of organic pollutants, is featured with fast reaction speed, good treatment effect, no need to add any chemical reagents, and no secondary pollution. This study explores the mechanism of improving anaerobic fermentation performance of rice samples pretreated by cobalt-60 gamma irradiation through the influence on fermentation substrate, acidogenic phase and methanogenic phase. The results reveal that the soluble chemical oxygen demand of the irradiated rice sample at an absorbed dose of 9.6 kGy increases by 12.4 times due to the dissolution of small molecules of fat-soluble organic matter. The yield of biogas in the acidogenic phase increases by 22.2% with a slight increase in hydrogen gas content. The yield of biogas and methane gas content in the methanogenic phase increases by 27.3% and 15%, respectively. Microbial genome analysis, performed with MiSeq high-throughput sequencing and metagenomic methods, suggests the microbial abundance and metabolic functions in the anaerobic fermentation process change significantly as a result of the pretreatment by gamma irradiation.

Hydrothermal co-liquefaction of microalgae, sugarcane bagasse, brewer's spent grain, and sludge from a paper recycling mill: Modeling and evaluation of biocrude and biochar yield.

Biomass can be used as an energy source to thermochemical conversion processes to biocrude production. However, the supply and dependence on only one biomass for biocrude production can be an obstacle due to its seasonality, availability, and logistics costs. In this way, biomass waste and agroindustrial residues can be mixture and used as feedstock to the hydrothermal co-liquefaction (co-HTL) process as an alternative to obtaining biocrude. In this sense, the present paper analyzed the biocrude yield influence of the co-HTL from a quaternary unprecedented blend of different biomasses, such as sugarcane bagasse, brewer's spent grain (BSG), sludge from a paper recycling mill (PRM), and microalgae (Chlorella vulgaris). In this way, a simplex lattice design was employed and co-HTL experiments were carried out in a 2000 mL high-pressure stirred autoclave reactor under 275 °C for 60 min, considering 15% of feedstock/water ratio. Significant effects in each feedstock and their blends were analyzed aiming to increase biocrude and biochar yield. It was found that the addition of microalgae is only significant when considered more than 50% into the blend with BSG and PRM sludge to increase biocrude yield.

Photoheterotroph improved the growth and nutrient levels of Chlorella vulgaris and the related molecular mechanism.

Microalgae are rich in fatty acids, proteins, and other nutrients, which have gained the general attention of researchers all over the world. For the development of Chlorella vulgaris in food and feed industry, this study was conducted to investigate the differences in C. vulgaris' growth and nutritional components under different culture conditions (autotrophic, heterotrophic, photoheterotrophic) and the internal factors through cell counting in combination with transcriptome and nutrient analyses. The results showed that, under the photoheterotrophic condition, Chlorella's growth and the contents of lipid and protein were significantly higher than that under the heterotrophic condition, and the moisture content was lower than that under the heterotrophic condition. The saturated fatty acid content under the photoheterotrophic condition was the lowest, while the polyunsaturated fatty acid content was significantly higher than those under the other two conditions. There were 46,583 differentially expressed genes (DEGs), including 33,039 up-regulated DEGs (70.93%) and 13,544 down-regulated DEGs (29.07%), under the photoheterotrophic condition in comparison with the autotrophic condition. The fold change between the two conditions of samples of up-regulated genes was higher than that of the down-regulated genes. The KEGG enrichment showed that the up-regulated DEGs in the photoheterotrophic condition were significantly enriched in 5 pathways, including protein processing in endoplasmic reticulum pathway, photosynthesis pathway, photosynthesis-antenna protein pathway, endocytosis pathway, and phosphonate and phosphinate metabolism pathway. DEGs related to fatty acid metabolic pathways were significantly enriched in the fatty acid biosynthesis pathway and the biosynthesis of unsaturated fatty acid pathway. The qPCR analysis showed that the expression pattern of the selected genes was consistent with that of transcriptome analysis. The results of this study lay a theoretical foundation for the large-scale production of Chlorella and its application in food, feed, and biodiesel. KEY POINTS: • Nutrient levels under photoheterotrophic condition were higher than other conditions. • Six important pathways were discovered that affect changes in nutritional composition. • Explored genes encode important enzymes in the differential metabolic pathways.

Stabilization of microbial network by co-digestion of swine manure and organic wastes.

The production of biogas from organic waste has attracted considerable interest as a solution to current energy and waste management challenges. This study explored the methane (CH4) production potential of swine manure (SM), food waste (FW), and tomato waste (TW) and the changes in the microbial community involved in the anaerobic digestion process. The results revealed that the CH4 production potentials of the four kinds of SM samples were influenced by the characteristics of SM (e.g., age and storage period). Among the four kinds of SM samples, the CH4 yield from the manure directly sampled from primiparous sows (SM3) was the highest. The CH4 yield was significantly improved when SM3 was co-digested with FW, but not with TW. The addition of SM fostered a stable CH4 production community by enhancing the interaction between methanogens and syntrophic bacteria. Furthermore, the addition of FW as a co-substrate may improve the functional redundancy structure of the methanogenesis-associated network. Overall, the characteristics of SM must be considered to achieve consistent CH4 yield efficiency from anaerobic digestion since CH4 production potentials of SM can be different. Also, the contribution of co-substrate to the synergistic relationship between methanogens and syntrophic bacteria can be considered when a co-substrate is selected in order to enhace CH4 yield from SM.

Environmental impacts of valorisation of crude glycerol from biodiesel production - A life cycle perspective.

Biodiesel production produces significant quantities of impure crude glycerol as a by-product. Recent increases in the global biodiesel production have led to a surplus of crude glycerol, rendering it a waste. As a result, different methods for its valorisation are currently being investigated. This paper assesses the life cycle environmental impacts of an emerging technology for purification of crude glycerol - a multi-step physico-chemical treatment - in comparison to incineration with energy recovery commonly used for its disposal. For the former, three different acids (H3PO4, H2SO4 and HCl) are considered for the acidification step in the purification process. The results suggest that the H2SO4-based treatment is the best option with 17 net-negative impacts out of the 18 categories considered; this is due to system credits for the production of purified glycerol, heat and potassium salts. In comparison to incineration with energy recovery, the H2SO4-based process has lower savings for the climate change impact (-311 versus -504 kg CO2 eq./t crude glycerol) but it performs better in ten other categories. Sensitivity analyses suggest that that the impacts of the physico-chemical treatment are highly dependent on crude glycerol composition, allocation of burdens to crude glycerol and credits for glycerol production. For example, treating crude glycerol with lower glycerol content would increase all impacts except climate change and fossil depletion due to the higher consumption of chemicals and lower production of purified glycerol. Considering crude glycerol as a useful product rather than waste and allocating to it burdens from biodiesel production would increase most impacts significantly, including climate change (22-40 %), while fossil depletion, freshwater and marine eutrophication would become net-positive. The findings of this research will be of interest to the biodiesel industry and other industrial sectors that generate crude glycerol as a by-product.

Progress and challenges in valorisation of biomass waste from ornamental trees pruning through pyrolysis processes. Prospects in the bioenergy sector.

Nowadays, the scarcity of energy resources is promoting the search for alternative energy sources, boosting interest in the use of forest lignocellulosic residue in the energy sector. In this study, the focus is on the energy recovery from two lignocellulosic residues originated during the pruning of ornamental trees (Horse Chestnut, CI, and False Acacia, FA). Both conventional and flash pyrolysis techniques were applied. The experimental pyrolysis variables were obtained from the study of the thermal behaviour of the pruning residues in thermogravimetric analysis. It was carried out under 5 heating rates and kinetic parameters were estimated using Flynn-Wall-Ozawa method. Results denoted higher maximum mass loss rate values for the same release temperature regions under FA experiments. Also, FA samples had lower final residues for the processes. However, activation energy values were so close for both species. FA was also linked to the faster reactions according frequency factor outcomes. Conventional pyrolysis of pruning residues was carried out in a horizontal oven of original design at a heating rate of 25 °C/min, at 750 °C and 60 min of permanence at that temperature; flash pyrolysis was tested in that oven at 750 and 850 °C. In these pyrolysis processes, three fractions were obtained: bio-char, bio-oil and gas. The physicochemical attributes of the bio-chars suggested their potential utility as biofuels (28.4-29.8 MJ/kg), adsorbent precursors or soil additives. Conventional pyrolysis bio-oils had a dominant monoaromatic hydrocarbons nature, with phenols being the most abundant (≥60%), while flash bio-oils contain mainly polycyclic aromatic hydrocarbons. Conventional pyrolysis gases contained up to 60 vol% of CO2; flash pyrolysis gases had high combustible gas content (CO, CH4, H2) and a low CO2 content (<25 vol%). As a result, their calorific value (18.06 MJ/kg) exhibited a threefold increase compared to the gas produced through conventional pyrolysis (6.04 MJ/kg).

In situ hydrodeoxygenation of heavy bio-oil using a Ce/Fe-based oxygen carrier in methanol-zero valent aluminum media.

Resource recovery from solid organic wastes, such as degradable plastics, and upgrading raw bio-oil are important ways for reducing carbon and pollution emissions. Hydrodeoxygenation (HDO) is a common thermochemical treatment to upgrade crude bio-oil. In this study, in order to realize in situ HDO during the hydropyrolysis of heavy bio-oil and degradable plastics, a reduced Fe/Ce oxygen carrier (OC) was used to catalytically remove oxygen from organics under the methanol-zero valent aluminum (ZV Al) media, where the hydrogen was produced during pyrolysis instead of a direct hydrogen supply. The results showed that the reduced OC captured the oxygen from the pyrolysis products of heavy bio-oil and degradable plastic, representing the multi-selectivity of reduced OC to phenols, ketones, etc. The ZV Al system promoted the production and utilization of hydrogen, as evidenced by the increased hydrogen content in gas phase and hydrocarbon content in liquid phase. The hydrocarbon component distribution in the liquid phase increased clearly when hydropyrolysis with degradable plastics addtion, but the excess degradable plastics addition caused increasing of the liquid product viscosity, and decreasing of the liquid products yield for the higher ash content in degradable plastic, and a higher ZV Al amount was required to maintain the hydropyrolysis. Molecular dynamics simulations verified the synergistic effect of degradable plastics and bio-oil by the pyrolysis behavior in different systems and temperatures, and the pyrolysis pathways were proposed. This non-autocatalytic system realized the resource recovery and heavy bio-oil upgrading using an Fe/Ce OC.

Response of fulvic acid linking to redox characteristics on methane and short-chain fatty acids in anaerobic digestion of chicken manure.

Fulvic acids (FAs) is formed during the bioconversion of organic matter (OM) to biogas during anaerobic digestion (AD) and has a complex structure and redox function. However, the evolutionary mechanisms of FAs during AD and its interactions with acid and methane production have not been sufficiently investigated, especially at different stages of AD. Intermittent AD experiments by chicken manure and rice husk showed significant structural changes and reduced aromatization of FAs (e.g., O-H stretch6, 14.10-0%; SR, 0.22-0.60). The electron donating capacity (EDC) [9.76-45.39 µmole-/(g C)] and electron accepting capacity (EAC) [2.55-5.20 µmole-/(g C)] of FAs showed a tendency of decreasing and then increasing, and FAs had a stronger electron transfer capacity (ETC) in the methanogenic stage. Correlation analysis showed that the EDC of FAs was influenced by their own structure (C-O stretch2, C-H bend1, C-H bend4, and N-H bend) and also had an inhibitory effect on propionic production, which further inhibited acetic production. The EAC of FAs was affected by molecular weight and had a promoting effect on methane production. Structural equation modelling identified three possible pathways for AD. The C-O stretch2 structure of FAs alone inhibits the production of propionic. In addition, pH can directly affect the EDC of FAs. This study provides a theoretical basis for the structural and functional evolution of FAs in AD of chicken manure on the mechanism of methane production.

An integrated approach for wastewater treatment and algae cultivation: Nutrient removal analysis, biodiesel extraction, and energy and environmental metrics enhancement.

Human urine is rich in nitrogen and phosphorus, and the presence of these elements in wastewater significantly disrupts the biogeochemical cycle. Meanwhile, green algal biomass cultivation is unfeasible without these nutrients. Hence, the present study integrates wastewater treatment and algae cultivation to extract biodiesel and improve its performance through fuel modification. Chlorella vulgaris algae was cultivated in different dilution ratios of water and urine, and the nutrient removal rate was analyzed. Chlorella vulgaris algae biodiesel (CAB) was derived through Bligh and Dyer's method followed by transesterification, and its functional and elemental groups were analyzed. The various volume concentrations of CAB were blended with regular diesel fuel (RDF), and 10% water was added to a 30% CAB blended RDF to evaluate the combustion performance and environmental impacts. The results of the experiments demonstrated that the algae cultivation effectively removed the wastewater nutrients. The functional and elemental groups of CAB are identical to those of RDF. The engine characteristics of test fuels report that the CAB-blend RDF fuel mixtures generate low carbon footprints, whereas negative impacts have been drawn for performance metrics and oxides of nitrogen emissions. The water-emulsified fuel outweighed the unfavorable effects and promoted more efficient and cleaner combustion.

Technoeconomic and carbon footprint analysis of simulated industrial scale biodiesel production process from mixed macroalgal and non-edible seed oil using sulphonated zinc doped recyclable biochar catalyst.

The present research explored the sustainable production of biodiesel from mixed oils of marine macroalgae and non-edible seeds using a sulphonated Zinc doped recyclable biochar catalyst derived from coconut husk. The maximum biodiesel conversion of 94.8 % was yielded with optimized conditions of 10:1 methanol to oil molar ratio, 4.8 % biochar catalyst concentration, 54.5 ℃ temperature and 87.4 min reaction time. A techno-economic assessment provided a favourable return on investment (ROI) of 21.59 % and 4.63 years of reimbursement period, with a calculated minimum selling price of 0.81 $/kg of produced biodiesel. The carbon footprint analysis results estimated an annual emission of 752.07 t CO2 which corresponds to 0.088 kg CO2 emission per kg of biodiesel produced from the simulated process. The study on economic viability and environmental consciousness of biodiesel production not only paves the way for a greener and sustainable future while also contributing to low carbon footprint.

Life-cycle and economic assessments of microalgae biogas production in suspension and biofilm cultivation systems.

Biogas production via anaerobic digestion is highly attractive for microalgae. The technology of microalgae cultivation has profound impacts on biogas production system as it is the most energy-consuming process. However, a comprehensive evaluation of the environmental and economic benefits of different cultivation systems has yet to be sufficiently conducted. Here, life-cycle and economic assessments of open raceway ponds, photobioreactors and biofilm systems were investigated. Results showed greenhouse gas emissions of all systems were positive because more than two-thirds of carbon in fuel gas was lost and the fixed carbon in product gas and solid fertilizer was less than the emitted carbon during energy input. Particularly, biofilm system achieved the least greenhouse gas emissions (9.3 g CO2-eq/MJ), net energy ratio (0.7) and levelized cost of energy (0.9 $/kWh), indicating the optimum cultivation system. Open raceway ponds and photobioreactors failed to achieve positive benefits because of low harvesting efficiency and biomass concentration.