Fractionation of dicarboxylic acids produced by Rhizopus oryzae using reactive extraction.

Fumaric, malic, and succinic acids have been selectively separated from their mixture obtained by Rhizopus oryzae fermentation using reactive extraction with Amberlite LA-2 dissolved in three solvents with different dielectric constants (n-heptane, n-butyl acetate, and dichloromethane). This technique allows recovering preferentially fumaric acid from the mixture, the raffinate containing only malic and succinic acids. The extractant concentration and organic phase polarity control the efficiency and selectivity of acids extraction. The increase of aqueous phase viscosity reduces the extraction yield for all studied acids, but exhibits a positively effect on separation selectivity. By using Amberlite LA-2 concentration equal to that stoichiometrically required for interfacial reaction with fumaric acid and mixing intensity which does not allow higher diffusion rates for larger molecules (malic and succinic acids), the maximum value of fumaric acid extraction rate exceeds 90%, while the selectivity factor value becomes 20. Regardless of the extraction system, the complete separation of fumaric acid from their mixture is possible by multi-stage extraction process, adjusting the extractant concentration in each stage. At higher values of aqueous phase viscosity, more extraction stages are required, while the increase of solvent polarity reduce the required number of stages for total recovery of fumaric acid.

Rapid hyperpolarization and purification of the metabolite fumarate in aqueous solution.

Hyperpolarized fumarate is a promising biosensor for carbon-13 magnetic resonance metabolic imaging. Such molecular imaging applications require nuclear hyperpolarization to attain sufficient signal strength. Dissolution dynamic nuclear polarization is the current state-of-the-art methodology for hyperpolarizing fumarate, but this is expensive and relatively slow. Alternatively, this important biomolecule can be hyperpolarized in a cheap and convenient manner using parahydrogen-induced polarization. However, this process requires a chemical reaction, and the resulting solutions are contaminated with the catalyst, unreacted reagents, and reaction side-product molecules, and are hence unsuitable for use in vivo. In this work we show that the hyperpolarized fumarate can be purified from these contaminants by acid precipitation as a pure solid, and later redissolved to a desired concentration in a clean aqueous solvent. Significant advances in the reaction conditions and reactor equipment allow for formation of hyperpolarized fumarate at 13C polarization levels of 30-45%.

Preparation of Sterile Raw Material - Chicken Eggshells in the Process of their Transformation into Selected Calcium Salts.

BACKGROUND: The chicken eggshells and their subcrustal membranes are a valuable source of calcium, but they are not further processed but disposed of as waste from the food industry. Chicken eggshells have high content (>95%) of calcium carbonate. Some properties suggest that eggshells may be a promising alternative to the present calcium sources used in the pharmaceutical industry. METHODS: The effect of roasting chicken eggshells with a selected organic acid (citric or fumaric or lactic acid) on microbiological purity, including the presence of fungi and bacteria Salmonella spp., Staphylococcus aureus, Escherichia coli of obtained calcium salts, was investigated. In this study, chicken eggshells were subjected to chemical reactions with organic acids (citric, fumaric or lactic acid) at two different calcium-acid molar ratios (1:1 or 1:3) and the mixture was heat-treated for 1 or 3 hours at a temperature of 100°C or 120°C. RESULTS AND DISCUSSION: It was found that lactic acid was 100% effective against fungi, and the remaining citric and fumaric acids were -50% (regardless of the other examined conditions). The type of acid used has a significant effect on fungal growth inhibition (p<0.05). Fumaric acid and lactic acid will be nearly 100% effective against bacteria (100% fumaric acid and 97% lactic acid effectiveness), regardless of other factors. CONCLUSION: Lactic acid is the most effective against pathogenic flora - fungi and bacteria. The transformation of chicken eggshells into calcium lactate can provide us with sterile calcium salt, free of 100% fungi and 97% of all bacteria.

Optimized Bioproduction of Itaconic and Fumaric Acids Based on Solid-State Fermentation of Lignocellulosic Biomass.

The bioproduction of high-value chemicals such as itaconic and fumaric acids (IA and FA, respectively) from renewable resources via solid-state fermentation (SSF) represents an alternative to the current bioprocesses of submerged fermentation using refined sugars. Both acids are excellent platform chemicals with a wide range of applications in different market, such as plastics, coating, or cosmetics. The use of lignocellulosic biomass instead of food resources (starch or grains) in the frame of a sustainable development for IA and FA bioproduction is of prime importance. Filamentous fungi, especially belonging to the Aspergillus genus, have shown a great capacity to produce these organic dicarboxylic acids. This study attempts to develop and optimize the SSF conditions with lignocellulosic biomasses using A. terreus and A. oryzae to produce IA and FA. First, a kinetic study of SSF was performed with non-food resources (wheat bran and corn cobs) and a panel of pH and moisture conditions was studied during fermentation. Next, a new process using an enzymatic cocktail simultaneously with SSF was investigated in order to facilitate the use of the biomass as microbial substrate. Finally, a large-scale fermentation process was developed for SSF using corn cobs with A. oryzae; this specific condition showed the best yield in acid production. The yields achieved were 0.05 mg of IA and 0.16 mg of FA per gram of biomass after 48 h. These values currently represent the highest reported productions for SSF from raw lignocellulosic biomass.

Fumaric acid: production and separation.

Fumaric acid is a valuable compound used in foods, beverages, detergents, animal feed, pharmaceuticals and miscellaneous industrial products. It is produced on a large scale by the petrochemical route but the current tendency is towards implementing "green production" and environmental friendly technologies like biotechnological production of fumaric acid using low-cost raw materials. In this context, numerous studies focus on improving the fermentation process not only by using renewable raw material and genetically modified microorganisms, but also by developing and applying different downstream techniques for easy recovery of fumaric acid from the fermented broth. This review presents the main methods for production and separation of fumaric acid, highlighting the advantages and disadvantages of these and the potential economic impact in industry.

Design of simulated moving bed for separation of fumaric acid with a little fronting phenomenon.

The production of fumaric acid through a biotechnological pathway has grown in importance because of its potential value in related industries. This has sparked an interest in developing an economically-efficient process for separation of fumaric acid (product of interest) from acetic acid (by-product). This study aimed to develop a simulated moving bed (SMB) chromatographic process for such separation in a systematic way. As a first step for this work, commercially available adsorbents were screened for their applicability to the considered separation, which revealed that an Amberchrom-CG71C resin had a sufficient potential to become an adsorbent of the targeted SMB. Using this adsorbent, the intrinsic parameters of fumaric and acetic acids were determined and then applied to optimizing the SMB process under consideration. The optimized SMB process was tested experimentally, from which the yield of fumaric-acid product was found to become lower than expected in the design. An investigation about the reason for such problem revealed that it was attributed to a fronting phenomenon occurring in the solute band of fumaric acid. To resolve this issue, the extent of the fronting was evaluated quantitatively using an experimental axial dispersion coefficient for fumaric acid, which was then considered in the design of the SMB of interest. The SMB experimental results showed that the SMB design based on the consideration of the fumaric-acid fronting could guarantee the attainment of both high purity (>99%) and high yield (>99%) for fumaric-acid product under the desorbent consumption of 2.6 and the throughput of 0.36L/L/h.

In vitro neuroprotective potential of lichen metabolite fumarprotocetraric acid via intracellular redox modulation.

The lichen-forming fungi Cetraria islandica has been largely used in folk medicines, and it has recently showed promising in vitro antioxidant effects in glial-like cells. Current work aimed at investigating the neuroprotective potential of its major isolated secondary metabolite: the depsidone fumarprotocetraric acid (FUM). H2O2 was used herein to induce oxidative stress (OS)-mediated cytotoxicity in two models of neurons and astrocytes cells (SH-SY5Y and U373-MG cell lines). We found that a pre-treatment with FUM significantly enhanced cell viability compared to H2O2-treated cells, and we selected the optimal concentrations in each model (1 and 25µg/ml, respectively) for assessing its cytoprotective mechanisms. FUM, which exerted effective peroxyl radical scavenging effect in the chemical oxygen radical antioxidant capacity (ORAC) assay, alleviated the alterations in OS markers provoked by H2O2. It attenuated intracellular ROS formation, lipid peroxidation and GSH depletion. At mitochondrial level, FUM prevented from the dissipation of mitochondrial membrane potential and the increase in mitochondrial calcium, implying a protective role against oxidative damage in mitochondrial membrane. Similarly, FUM pre-treatment diminished H2O2-induced apoptosis, as evidenced by the reduction in caspase-3 activity and expression; inmunoblot analysis also revealed a decrease in Bax and an increase in Bcl-2 proteins levels. Furthermore, FUM up-regulated the expression of the antioxidant enzymes catalase, superoxide dismutase-1, and hemeoxigenase-1. These findings and the activation of Nrf2 binding activity in nuclear extracts suggest a plausible involvement of Nrf2 signaling pathway in the cytoprotection by FUM. In conclusion, FUM emerges as a potential drug candidate in the therapy of OS-related diseases, such as the neurodegenerative disorders.

Fumaric Acid Production from Alkali-Pretreated Corncob by Fed-Batch Simultaneous Saccharification and Fermentation Combined with Separated Hydrolysis and Fermentation at High Solids Loading.

Production of fumaric acid from alkali-pretreated corncob (APC) at high solids loading was investigated using a combination of separated hydrolysis and fermentation (SHF) and fed-batch simultaneous saccharification and fermentation (SSF) by Rhizopus oryzae. Four different fermentation modes were tested to maximize fumaric acid concentration at high solids loading. The highest concentration of 41.32 g/L fumaric acid was obtained from 20 % (w/v) APC at 38 °C in the combined SHF and fed-batch SSF process, compared with 19.13 g/L fumaric acid in batch SSF alone. The results indicated that a combination of SHF and fed-batch SSF significantly improved production of fumaric acid from lignocellulose by R. oryzae than that achieved with batch SSF at high solids loading.

Engineering nonphosphorylative metabolism to synthesize mesaconate from lignocellulosic sugars in Escherichia coli.

Dicarboxylic acids are attractive biosynthetic targets due to their broad applications and their challenging manufacturing process from fossil fuel feedstock. Mesaconate is a branched, unsaturated dicarboxylic acid that can be used as a co-monomer to produce hydrogels and fire-retardant materials. In this study, we engineered nonphosphorylative metabolism to produce mesaconate from d-xylose and l-arabinose. This nonphosphorylative metabolism is orthogonal to the intrinsic pentose metabolism in Escherichia coli and has fewer enzymatic steps and a higher theoretical yield to TCA cycle intermediates than the pentose phosphate pathway. Here mesaconate production was enabled from the d-xylose pathway and the l-arabinose pathway. To enhance the transportation of d-xylose and l-arabinose, pentose transporters were examined. We identified the pentose/proton symporter, AraE, as the most effective transporter for both d-xylose and l-arabinose in mesaconate production process. Further production optimization was achieved by operon screening and metabolic engineering. These efforts led to the engineered strains that produced 12.5g/l and 13.2g/l mesaconate after 48h from 20g/l of d-xylose and l-arabinose, respectively. Finally, the engineered strain overexpressing both l-arabinose and d-xylose operons produced 14.7g/l mesaconate from a 1:1 d-xylose and l-arabinose mixture with a yield of 85% of the theoretical maximum. (0.87g/g). This work demonstrates an effective system that converts pentoses into a value-added chemical, mesaconate, with promising titer, rate, and yield.

Nutritional and Biochemical Profiling of Leucopaxillus candidus (Bres.) Singer Wild Mushroom.

The wild mushroom Leucopaxillus candidus (Bres.) Singer was studied for the first time to obtain information about its chemical composition, nutritional value and bioactivity. Free sugars, fatty acids, tocopherols, organic and phenolic acids were analysed by chromatographic techniques coupled to different detectors. L. candidus methanolic extract was tested regarding antioxidant potential (reducing power, radical scavenging activity and lipid peroxidation inhibition). L. candidus was shown to be an interesting species in terms of nutritional value, with high content in proteins and carbohydrates, but low fat levels, with the prevalence of polyunsaturated fatty acids. Mannitol was the most abundant free sugar and ß-tocopherol was the main tocopherol isoform. Other compounds detected were oxalic and fumaric acids, p-hydroxybenzoic and cinnamic acids. The methanolic extract revealed antioxidant activity and did not show hepatoxicity in porcine liver primary cells. The present study provides new information about L. candidus.

Modular optimization of multi-gene pathways for fumarate production.

Microbial fumarate production from renewable feedstock is a promising and sustainable alternative to petroleum-based chemical synthesis. Here, we report a modular engineering approach that systematically removed metabolic pathway bottlenecks and led to significant titer improvements in a multi-gene fumarate metabolic pathway. On the basis of central pathway architecture, yeast fumarate biosynthesis was re-cast into three modules: reduction module, oxidation module, and byproduct module. We targeted reduction module and oxidation module to the cytoplasm and the mitochondria, respectively. Combinatorially tuning pathway efficiency by constructing protein fusions RoMDH-P160A and KGD2-SUCLG2 and optimizing metabolic balance by controlling genes RoPYC, RoMDH-P160A, KGD2-SUCLG2 and SDH1 expression strengths led to significantly improved fumarate production (20.46 g/L). In byproduct module, synthetizing DNA-guided scaffolds and designing sRNA switchs enabled further production improvement up to 33.13 g/L. These results suggest that modular pathway engineering can systematically optimize biosynthesis pathways to enable an efficient production of fumarate.

High production of fumaric acid from xylose by newly selected strain Rhizopus arrhizus RH 7-13-9#.

Fumaric acid, as an important material for polymerization, is highly expected to be produced by fermentation of lignocellulosic biomass which is composed of cellulose, hemicellulose and lignin. Xylose as the main component of hemicellulose cannot be efficiently utilized by most of the common fermentation. In this study, a new strain Rhizopus arrhizus RH 7-13-9# was selected from the R. arrhizus RH 7-13 through a novel convenient and efficient selection method. Efficient production of fumaric acid (45.31 g/L) from xylose was achieved by the new strain, and the volumetric productivity was still 0.472 g/L h. Moreover, the conversion of xylose reached 73% which is close to the theoretic yield (77%). The production of fumaric acid was increased approximate by 172%, compared with the initial strain counterpart. These results indicated that xylose, as the main component of hemicellulose, has a promising application for the production of fumaric acid on an industrial-scale.

Engineering Scheffersomyces stipitis for fumaric acid production from xylose.

In this work, Scheffersomyces stipitis, the yeast with excellent xylose-utilizing ability, was firstly engineered for fumaric acid production from xylose with the heterologous reductive pathway from Rhizopus oryzae FM19, and 1.86g/L fumaric acid was produced by the initial strain PSRPMF under the oxygen-limited condition. Furthermore, three strategies were performed to improve the fumaric acid production, including increasing the reductive pathway activity by codon optimization, blocking the fumaric acid conversion in tricarboxylic acid cycle by knocking out the native fumarases, and improving the fumaric acid transportation by overexpressing heterologous transporter. Finally, the strain PSYPMFfS was obtained and the fumaric acid titer reached to 4.67g/L, significantly increased by 37.92-fold than that of the control strain PSPYSS. It was indicated that the S. stipitis was a promising platform for fumaric acid production from xylose.

Enhanced acid tolerance of Rhizopus oryzae during fumaric acid production.

Ensuring a suitable pH in the culture broth is a major problem in microorganism-assisted industrial fermentation of organic acids. To address this issue, we investigated the physiological changes in Rhizopus oryzae at different extracellular pH levels and attempted to solve the issue of cell shortage under low pH conditions. We compared various parameters, such as membrane fatty acids' composition, intracellular pH, and adenosine triphosphate (ATP) concentration. It was found that the shortage of intracellular ATP might be the main reason for the low rate of fumaric acid production by R. oryzae under low pH conditions. When 1 g/l citrate was added to the culture medium at pH 3.0, the intracellular ATP concentration increased from 0.4 to 0.7 µmol/mg, and the fumaric acid titer was enhanced by 63% compared with the control (pH 3.0 without citrate addition). The final fumaric acid concentration at pH 3.0 reached 21.9 g/l after 96 h of fermentation. This strategy is simple and feasible for industrial fumaric acid production under low pH conditions.

Nanofiltration, bipolar electrodialysis and reactive extraction hybrid system for separation of fumaric acid from fermentation broth.

A novel approach based on a hybrid system allowing nanofiltration, bipolar electrodialysis and reactive extraction, was proposed to remove fumaric acid from fermentation broth left after bioconversion of glycerol. The fumaric salts can be concentrated in the nanofiltration process to a high yield (80-95% depending on pressure), fumaric acid can be selectively separated from other fermentation components, as well as sodium fumarate can be conversed into the acid form in bipolar electrodialysis process (stack consists of bipolar and anion-exchange membranes). Reactive extraction with quaternary ammonium chloride (Aliquat 336) or alkylphosphine oxides (Cyanex 923) solutions (yield between 60% and 98%) was applied as the final step for fumaric acid recovery from aqueous streams after the membrane techniques. The hybrid system permitting nanofiltration, bipolar electrodialysis and reactive extraction was found effective for recovery of fumaric acid from the fermentation broth.

Expectorant and antioxidant activities of purified fumarprotocetraric acid from Cladonia verticillaris lichen in mice.

UNLABELLED: The lichen Cladonia verticillaris produces bioactive secondary metabolites, such as fumarprotocetraric (FUM) and protocetraric acids. Species of the genus Cladonia demonstrate anti-tumor, anti-inflammatory and antipyretic activities and have been used in folk medicine to treat respiratory diseases (throat irritation, cough, asthma and tuberculosis). The aim of the present study was to evaluate the expectorant and mucolytic activities of fumarprotocetraric acid in albino Swiss mice. FUM was extracted and purified from an acetone extract of C. verticillaris. The phenol red quantification method was used on the bronchoalveolar lavage fluid following the administration of FUM (25, 50 or 100 mg/kg orally or intraduodenally and 12.5, 25 or 50 mg/kg, intraperitoneally) for the evaluation of expectorant activity. Control groups received either saline solution (7.5 mL/kg) or ambroxol (1 mg/kg) through the same administration routes. Antioxidant activity was evaluated using the thiobarbituric acid reactive species assay in mouse lung tissue treated with the FUM at 25, 50 or 100 mg/kg orally, followed by a lipopolysaccharide solution at 1 mg/kg intrapleurally. The same protocol was used for the control groups using either saline solution (7.5 mL/kg, orally) or N-acetylcysteine (20 mg/kg, orally). RESULTS: Orally administered FUM at doses of 25 and 50 mg/kg promoted significantly greater dose-dependent phenol red activity in the bronchoalveolar lavage and expectorant activity in comparison to the controls (p < 0.05). Lipid peroxidation (malondialdehyde equivalent) was reduced by 50% in the lung tissue. CONCLUSION: The results confirm the expectorant and antioxidant properties of fumarprotocetraric acid produced by the lichen C. verticillaris.

End-to-end continuous manufacturing of pharmaceuticals: integrated synthesis, purification, and final dosage formation.

A series of tubes: The continuous manufacture of a finished drug product starting from chemical intermediates is reported. The continuous pilot-scale plant used a novel route that incorporated many advantages of continuous-flow processes to produce active pharmaceutical ingredients and the drug product in one integrated system.

Identification of putative steroid receptor antagonists in bottled water: combining bioassays and high-resolution mass spectrometry.

Endocrine disrupting chemicals (EDCs) are man-made compounds interfering with hormone signaling and thereby adversely affecting human health. Recent reports provide evidence for the presence of EDCs in commercially available bottled water, including steroid receptor agonists and antagonists. However, since these findings are based on biological data the causative chemicals remain unidentified and, therefore, inaccessible for toxicological evaluation. Thus, the aim of this study is to assess the antiestrogenic and antiandrogenic activity of bottled water and to identify the causative steroid receptor antagonists. We evaluated the antiestrogenic and antiandrogenic activity of 18 bottled water products in reporter gene assays for human estrogen receptor alpha and androgen receptor. Using nontarget high-resolution mass spectrometry (LTQ-Orbitrap Velos), we acquired corresponding analytical data. We combined the biological and chemical information to determine the exact mass of the tentative steroid receptor antagonist. Further MS(n) experiments elucidated the molecule's structure and enabled its identification. We detected significant antiestrogenicity in 13 of 18 products. 16 samples were antiandrogenic inhibiting the androgen receptor by up to 90%. Nontarget chemical analysis revealed that out of 24520 candidates present in bottled water one was consistently correlated with the antagonistic activity. By combining experimental and in silico MS(n) data we identified this compound as di(2-ethylhexyl) fumarate (DEHF). We confirmed the identity and biological activity of DEHF and additional isomers of dioctyl fumarate and maleate using authentic standards. Since DEHF is antiestrogenic but not antiandrogenic we conclude that additional, yet unidentified EDCs must contribute to the antagonistic effect of bottled water. Applying a novel approach to combine biological and chemical analysis this is the first study to identify so far unknown EDCs in bottled water. Notably, dioctyl fumarates and maleates have been overlooked by science and regulation to date. This illustrates the need to identify novel toxicologically relevant compounds to establish a more holistic picture of the human exposome.

Engineered fumarate sensing Escherichia coli based on novel chimeric two-component system.

DcuS/DcuR two component system (TCS) was firstly employed for the expression of the gfp gene under the dcuB gene promoter in aerobic condition to develop high throughput screening system able to screen microorganisms producing high amount of fumarate. However, the DcuS/DcuR TCS could not produce a signal strong enough to mediate the expression of the gfp gene responding fumarate concentration. Thus, DcuS/DucR TCS was engineered by recruiting the EnvZ/OmpR system, the most-studied TCS in E. coli. A chimeric DcuS/EnvZ (DcuSZ) TCS was constructed by fusing the sensor histidine kinase of DcuS with the cytoplasmic catalytic domain of EnvZ, in which the expression of the gfp gene or the ompC gene was mediated by the ompC gene promoter through the cognate response regulator, OmpR. The output signals produced by the chimeric DcuSZ TCS were enough to detect fumarate concentration quantatively, in which the expressions of the gfp gene and the ompC gene were proportional to the fumarate concentration in the medium. Moreover, principal component analysis of C4-dicarboxylates showed that DcuSZ chimera was highly specific to fumarate but could also respond to other C4-dicarboxylates, which strongly suggests that TCS-based high throughput screening system able to screen microorganisms producing target chemicals can be developed.

Lichenic extracts and metabolites as UV filters.

Three lichen extracts and ten lichenic compounds have been screened for their photoprotective activities. The determination of their Sun Protection Factor (SPF) and Protection Factor-UVA (PF-UVA) values was done in vitro. Among them, a Lasallia pustulata extract and gyrophoric acid exhibited SPF values over 5, which is better than Homosalate (SPF≈4). Their photoprotective properties are only slightly modified after a 2-hours period of irradiation. Salazinic acid and L. pustulata presented characteristics of a UVA booster like the butyl-methoxydibenzoylmethane (Avobenzone) (PF-UVA≈2 vs. 2.8 for Avobenzone). Salazinic acid was a better anion superoxide scavenger than ascorbic acid and none of them exhibited a photosensitizing cytotoxicity by exposing them on HaCaT cells to UVA radiations (photo-irritancy factor PIF<5).