Large-scale soil application of hydrochar: Reducing its polycyclic aromatic hydrocarbon content and toxicity by heating.

The beneficial roles of hydrochar in carbon sequestration and soil improvement are widely accepted. Despite few available reports regarding polycyclic aromatic hydrocarbons (PAHs) generated during preparation, their potential negative impacts on ecosystems remain a concern. A heating treatment method was employed in this study for rapidly removing PAHs and reducing the toxicity of corn stover-based hydrochar (CHC). The result showed total PAHs content (∑PAH) decreased and then sharply increased within the temperature range from 150 °C to 400 °C. The ∑PAH and related toxicity in CHC decreased by more than 80% under 200 °C heating temperature, compared with those in the untreated sample, representing the lowest microbial toxicity. Benzo(a)pyrene produced a significant influence on the ecological toxicity of the hydrochar among the 16 types of PAHs. The impact of thermal treatment on the composition, content, and toxicity of PAHs was significantly influenced by the adsorption, migration, and desorption of PAHs within hydrochar pores, as well as the disintegration and aggregation of large molecular polymers. The combination of hydrochar with carbonized waste heat and exhaust gas collection could be a promising method to efficiently and affordably reduce hydrochar ecological toxicity.

Simultaneous production of biosurfactant and extracellular unspecific peroxygenases by Moesziomyces aphidis XM01 enables an efficient strategy for crude oil degradation.

Crude oil is a hazardous pollutant that poses significant and lasting harm to human health and ecosystems. In this study, Moesziomyces aphidis XM01, a biosurfactant mannosylerythritol lipids (MELs)-producing yeast, was utilized for crude oil degradation. Unlike most microorganisms relying on cytochrome P450, XM01 employed two extracellular unspecific peroxygenases, MaUPO.1 and MaUPO.2, with preference for polycyclic aromatic hydrocarbons (PAHs) and n-alkanes respectively, thus facilitating efficient crude oil degradation. The MELs produced by XM01 exhibited a significant emulsification activity of 65.9% for crude oil and were consequently supplemented in an "exogenous MELs addition" strategy to boost crude oil degradation, resulting in an optimal degradation ratio of 72.3%. Furthermore, a new and simple "pre-MELs production" strategy was implemented, achieving a maximum degradation ratio of 95.9%. During this process, the synergistic up-regulation of MaUPO.1, MaUPO.1 and the key MELs synthesis genes contributed to the efficient degradation of crude oil. Additionally, the phylogenetic and geographic distribution analysis of MaUPO.1 and MaUPO.1 revealed their wide occurrence among fungi in Basidiomycota and Ascomycota, with high transcription levels across global ocean, highlighting their important role in biodegradation of crude oil. In conclusion, M. aphidis XM01 emerges as a novel yeast for efficient and eco-friendly crude oil degradation.

Adjustable chromatographic performance of silica-based mixed-mode stationary phase through the control of co-grafting amounts of imidazole and C18 chain.

In this paper, three imidazole- and C18- bifunctional silica stationary phases (Sil-Im-C18) were prepared by adjusting introduction interval of octadecyltrichlorosilane (ODS) and 3-imidazol-1-ylpropyl(trimethoxy)silane (TMPImS), which can be used for reversed-phase liquid chromatography (RPLC) and ion exchange chromatography (IEC) with adjustable performance. The successful preparation of Sil-Im-C18 were confirmed by the characterizations of elemental analysis, infrared spectroscopy (FTIR) and contact angle (CA). Chromatographic performance of Sil-Im-C18 were evaluated by the separation of Tanaka test mixture, alkylbenzenes, linear PAHs and a set of analytes with different properties (uracil, phenol, 1,2-dinitrobenzene and naphthalene), and compared with commonly used C18 column. It was found that the chromatographic performance of Sil-Im-C18 changed significantly with the difference in bonding amount of imidazole and C18. Sil-Im-C18 demonstrated the excellent separation performance towards polycyclic aromatic hydrocarbons (PAHs), phenylesters, phenylamines, phenols and inorganic anions, and notably, nucleobases and nucleosides can be separated using pure water as mobile phases. The van Deemter plot showed that the column efficiency of Sil-Im-C18-3 was 64,933 plate·m-1 for naphthalene, indicated that Sil-Im-C18 was reasonably chromatographic columns. The RSD values of retention time were 0.22 %-0.61 % for 10 needles alkylbenzenes injected continuously at 50 °C to investigate thermal stability and repeatability, all the fluctuations of k of naphthalene were less than 2.3 % for Sil-Im-C18-1 during flushing 24 h with the mobile phase at different pH values (pH = 3 and 8), the retention time of alkylbenzenes were almost same for Sil-Im-C18-1 at different time, the RSD values of retention time of alkylbenzenes were 0.45 %-2.28 % for two batches Sil-Im-C18-1, revealing the excellent repeatability, thermal stability, durability and reproducibility of Sil-Im-C18, and implying a commercial prospect.

Mechanism of soot and particulate matter formation during high temperature pyrolysis and gasification of waste derived from MSW.

This research investigates the formation mechanism of soot and particulate matter during the pyrolysis and gasification of waste derived from Municipal Solid Waste (MSW) in a laboratory scale drop tube furnace. Compared with CO2 gasification atmosphere, more ultrafine particles (PM0.2, aerodynamic diameter less than 0.2 µm) were generated in N2 atmosphere at 1200℃, which were mainly composed of polycyclic aromatic hydrocarbons (PAHs), graphitic carbonaceous soot and volatile alkali salts. High reaction temperatures promote the formation of hydrocarbon gaseous products and their conversion to PAHs, which ultimately leads to the formation of soot particles. The soot particles generated by waste derived from MSW pyrolysis and gasification both have high specific surface area and well-developed pore structure. Compared with pyrolysis, the soot generated by gasification of waste derived from MSW had smaller size and higher proportion of inorganic components. The higher pyrolysis temperature led to the collapse of the mesoporous structure of submicron particles, resulting in a decrease in total pore volume and an increase in specific surface area. Innovatively, this research provides an explanation for the effect of reaction temperature/ CO2 on the formation pathways and physicochemical properties of soot and fine particulate matter.

The effect of bioturbation on the release behavior of polycyclic aromatic hydrocarbons from sediments: A sediment-seawater microcosm experiment combined with a fugacity model.

The effects of two benthonic species, Perinereis aibuhitensis and Matuta planipes Fabricius, on the release of polycyclic aromatic hydrocarbons (PAHs) from sediments were investigated using a sediment-seawater microcosm. A Level IV fugacity model was used to simulate the behavior and fate of PAHs in the environment. This study revealed that both benthos significantly influenced the release of PAHs, and Matuta planipes Fabricius had a stronger disturbance effect than another. The final concentrations of Matuta planipes Fabricius group, Perinereis aibuhitensis group and the control group in the seawater phase reached 10.8, 9.94 and 7.90 µg/L, respectively. There were certain differences in the behaviour of the two benthonic species. Matuta planipes Fabricius caused more sediment resuspension, while Perinereis aibuhitensis increased the total organic carbon (TOC) content in the environment. The vertical concentration distribution of sediment indicated that vertical mixing was slightly stronger in the Matuta planipes Fabricius group than that in the Perinereis aibuhitensis group. The fugacity model effectively simulated the release behavior of PAHs, providing insight into PAH transport and distribution. The results demonstrated that bioturbation could promote the release of PAHs from seawater. The amount of PAHs released was significantly correlated with the biological habits of the benthos.

Non-target analysis of crude oil photooxidation products at high latitudes and their biological effects.

With new oil and gas lease sales in high-latitude regions, there exists a need to better understand the chemical fate of spilled oil and its effects on biological life. To address this need, laboratory simulations of crude oil spills under sub-Arctic conditions were conducted using artificial seawater and exposure to solar irradiation to create Hydrocarbon Oxidation Products (HOPs). HOPs characterization and their biological effects were assessed using ultra high-performance liquid chromatography (UHPLC) with high resolution mass Orbitrap spectrometry and the aryl hydrocarbon receptor (AhR) chemically activated luciferase gene expression (CALUX) assay. Non-target UHPLC-Orbitrap mass spectrometry analysis identified 251 HOPs that were in greater abundance in light-exposed samples than dark controls. Oxidized polycyclic aromatic hydrocarbons were also detected, including phenanthrene quinone, anthraquinone, hydroxyanthraquinone, and 9-fluoreneone. The composition of HOPs were consistent with photo-products of alkylated two to four ring PAHs, primarily compounds between 1 and 3 aromatic rings and 1-3 oxygens. The HOP mixture formed during photochemical weathering of Cook Inlet crude oil induced greater AhR activity than parent petroleum products solubilized in dark controls, indicating that HOPs, as a complex mixture, may contribute to petroleum toxicity more than the parent petroleum compounds. These non-targeted approaches provide the most comprehensive analysis of hydrocarbon oxidation products to date, highlighting the diversity of the complex mixture resulting from the photooxidation of crude oil and the limitations of targeted analyses for adequately monitoring HOPs in the environment. Taken together, these data identify a critical "blind spot" in environmental monitoring and spill clean-up strategies as there is a diverse pool of HOPs that may negatively impact human and ecosystem health.

Interpretation of adsorption isotherm and kinetics behind fluorene degradation.

The gradual release of slow-degrading polycyclic aromatic hydrocarbons into the environment creates a high level of threat to aquatic and terrestrial life worldwide. Remediation of these PAHs should be designed in such a way that it poses as few or no environmental hazards as possible. In our study, we examined the degradation ability of the synthesized MnO2 nanoparticles against fluorene. The MnO2 nanoparticle prepared was found to be spherical from the SEM analysis. XRD analysis confirms the average crystallite size as 31.8652 nm. Further, the characterization of nanoparticles was confirmed by UV-DRS, FT-IR, DLS, and HPLC techniques. The extent of adsorption potential of the synthesized nanoparticles was established from the batch adsorption studies and the kinetic and isotherm model was interpreted. The antimicrobial properties of the synthesized MnO2 nanoparticles were analyzed.

Viscosities and Densities of Binary and Ternary Mixtures of Aliphatic and Polyaromatic Hydrocarbons: Pyrene +1-Methylnaphthalene + Dodecane at T = (293.15 to 343.15) K. Experiment and Modeling.

This work presents new experimental viscosity and density data for aromatic and polyaromatic compounds in binary and ternary pyrene, 1-methylnaphthalene, and dodecane mixtures. The lack of experimental viscosity data for these mixtures requires the development of a new database, which is vital for understanding the behavior of mixtures in more complex systems, such as asphaltenes and fuels. The mixtures proposed in this work have been measured over a temperature range of (293.15 to 343.15) K at atmospheric pressure. Several mixture compositions have been studied at these conditions: 1.0, 2.5, 5.0, 7.5, 10.0, 12.5, and 15.0% pyrene mass fraction. The concentration of pyrene correlates with an increase in the viscosity and density values. At the lowest temperature in binary mixtures, the corresponding values reach 4.4217 mPa·s for viscosity and 1.0447 × 103 kg·m-3 for density, respectively. In ternary mixtures, the introduction of dodecane leads to the lowest maximum values of 3.5555 mPa·s for viscosity and 1.0112 × 103 kg·m-3 for density at the same temperature. The experimental data have been employed for the specific modification of viscosity models. These modifications could facilitate the prediction of the viscosity of mixtures that are more complex than those presented in this work. Various viscosity models have been employed, such as Linear, Ratcliff and Khan, modified UNIFAC-Visco, and Krieger-Dougherty. The settings in the models used reliably reproduce the experiment reliably. However, the Ratcliff model agrees excellently with the experiment, having a low standard deviation (2.0%) compared to other models. Furthermore, a model based on the equation of state of Guo is proposed to predict the viscosity values by modifying the specific parameters and adjusting them to the mixtures proposed in this work. The results from this study are compared to previous work, where pyrene, toluene, and heptane mixtures were analyzed. In this case, we find that the decrease of aggregation grade in the present systems is predicted by the model fixed in this work.

PAH bioremediation with Rhodococcus rhodochrous ATCC 21198: Impact of cell immobilization and surfactant use on PAH treatment and post-remediation toxicity.

Polycyclic aromatic hydrocarbons (PAHs) are prevalent environmental contaminants that are harmful to ecological and human health. Bioremediation is a promising technique for remediating PAHs in the environment, however bioremediation often results in the accumulation of toxic PAH metabolites. The objectives of this research were to demonstrate the cometabolic treatment of a mixture of PAHs by a pure bacterial culture, Rhodococcus rhodochrous ATCC 21198, and investigate PAH metabolites and toxicity. Additionally, the surfactant Tween ® 80 and cell immobilization techniques were used to enhance bioremediation. Total PAH removal ranged from 70-95% for fluorene, 44-89% for phenanthrene, 86-97% for anthracene, and 6.5-78% for pyrene. Maximum removal was achieved with immobilized cells in the presence of Tween ® 80. Investigation of PAH metabolites produced by 21198 revealed a complex mixture of hydroxylated compounds, quinones, and ring-fission products. Toxicity appeared to increase after bioremediation, manifesting as mortality and developmental effects in embryonic zebrafish. 21198's ability to rapidly transform PAHs of a variety of molecular structures and sizes suggests that 21198 can be a valuable microorganism for catalyzing PAH remediation. However, implementing further treatment processes to address toxic PAH metabolites should be pursued to help lower post-remediation toxicity in future studies.

A novel remediation strategy of mixed calcium peroxide and degrading bacteria for polycyclic aromatic hydrocarbon contaminated water.

Polycyclic aromatic hydrocarbons (PAHs) are a class of toxic organic pollutants commonly detected in the aqueous phase. Traditional biodegradation is inefficient and advanced oxidation technologies are expensive. In the current study, a novel strategy was developed using calcium peroxide (CP) and PAH-degrading bacteria (PDB) to effectively augment PAH degradation by 28.62-59.22%. The PDB consisted of the genera Acinetobacter, Stenotrophomonas, and Comamonas. Applying the response surface model (RSM), the most appropriate parameters were identified, and the predictive degradation rates of phenanthrene (Phe), pyrene (Pyr), and ΣPAHs were 98%, 76%, and 84%, respectively. The constructed mixed system could reduce 90% of Phe and more than 60% of ΣPAHs and will perform better at pH 5-7 and lower salinity. Because PAHs tend to bind to dissolved organic matter (DOM) with larger molecular weights, humic acid (HA) had a larger negative effect on the PAH-degradation efficiency of the CP-PDB mixed system than fulvic acid (FA). The proposed PAH-degradation pathways in the mixed system were based on the detection of intermediates at different times. The investigation constructed and optimized a novel environmental PAH-degradation strategy. The synergistic application of PDB and oxidation was extended for organic contaminant degradation in aqueous environments.

Poly-(ionic liquid) coated with magnetic nanoparticles for micro solid phase extraction of polycyclic aromatic hydrocarbons in food samples.

Poly(methyl methacrylate-vinyl imidazole bromide) (poly-MMA-IL)-grafted magnetic nanoparticles were successfully developed and applied in the micro-magnetic solid phase extraction (µ-MSPE) for 16 types of polycyclic aromatic hydrocarbons (PAHs) from tea, fried food, and grilled food samples via gas chromatography flame ionization detector (GC-FID). One variable at a time (OVAT) and response surface methodology (RSM) were used for efficient optimization. The validation method showed a good coefficient of determination (R2) ranging from 0.9901 to 0.9982 (n = 3) with linearity of 0.2 µg L-1-500 µg L-1. Detection and quantification limits were 0.06 µg L-1-0.32 µg L-1 and 0.18 µg L-1-0.97 µg L-1. Additionally, satisfactory reproducibility was attained with intra-day and inter-day precisions having RSD ranges of 3.6%-11.1%. The spiked recovery value of 16 PAHs in fried food, grilled food and tea samples obtained from the night market in Malaysia ranged from 80%-12%, respectively.

Cardiolipin Membranes Promote Cytochrome c Transformation of Polycyclic Aromatic Hydrocarbons and Their In Vivo Metabolites.

The catalytic properties of cytochrome c (Cc) have captured great interest in respect to mitochondrial physiology and apoptosis, and hold potential for novel enzymatic bioremediation systems. Nevertheless, its contribution to the metabolism of environmental toxicants remains unstudied. Human exposure to polycyclic aromatic hydrocarbons (PAHs) has been associated with impactful diseases, and animal models have unveiled concerning signs of PAHs' toxicity to mitochondria. In this work, a series of eight PAHs with ionization potentials between 7.2 and 8.1 eV were used to challenge the catalytic ability of Cc and to evaluate the effect of vesicles containing cardiolipin mimicking mitochondrial membranes activating the peroxidase activity of Cc. With moderate levels of H2O2 and at pH 7.0, Cc catalyzed the oxidation of toxic PAHs, such as benzo[a]pyrene, anthracene, and benzo[a]anthracene, and the cardiolipin-containing membranes clearly increased the PAH conversions. Our results also demonstrate for the first time that Cc and Cc-cardiolipin complexes efficiently transformed the PAH metabolites 2-hydroxynaphthalene and 1-hydroxypyrene. In comparison to horseradish peroxidase, Cc was shown to reach more potent oxidizing states and react with PAHs with ionization potentials up to 7.70 eV, including pyrene and acenaphthene. Spectral assays indicated that anthracene binds to Cc, and docking simulations proposed possible binding sites positioning anthracene for oxidation. The results give support to the participation of Cc in the metabolism of PAHs, especially in mitochondria, and encourage further investigation of the molecular interaction between PAHs and Cc.

The high dose of biochar reduces polycyclic aromatic hydrocarbons losses during co-composting of sewage sludge and wheat straw.

The aim of the study was to investigate the effect of the biochar (BC) dose on solvent extractable (Ctot) and freely dissolved (Cfree) polycyclic aromatic hydrocarbons (PAHs) content during co-composting. A significantly better reduction of Σ16 Ctot PAHs after 98 days occurred during composting with BC (for 1% of BC - 44% and for 5% of BC - 23%) than in the control (15%). Despite the relatively high reduction of Ctot PAHs in the experiment with 5% BC rate, the content of the PAHs was still the highest compared to other variants. Regarding Cfree PAHs, 5% rate of BC resulted in the best reduction of PAHs, while the 1% BC dose resulted in a lower reduction of Cfree than the control. For 1% BC, PAHs losses was more effective, and sequestration processes played a less significant role than in the experiment with 5% dose of BC. The total and dissolved organic carbon, and ash were predominantly responsible for Ctot and Cfree losses, and additionally pH for Cfree. The results of the experiment indicate that BC performs a crucial role in composting, affecting the Ctot and Cfree PAHs in the compost but the final effect strictly depends on the BC dose.

Effect of chemical aging on phosphate adsorption and ecotoxicological properties of magnesium-modified biochar.

Using magnesium-biochar composites (Mg-BC) in adsorption allows for the efficient and economically relevant removal of phosphate (PO43-) from water and wastewater. Applying Mg-BC for pollutant removal requires evaluating the adsorption capacity of composites and their ecotoxicological properties. Investigating the composite aging during the application of these composites into the soil is also essential. In the present study, nonaged and aged (at 60 or 90 °C) Mg-BC composites were investigated in the context of pyrolysis temperature (500 or 700 °C). All analyzed biochars were examined by Fourier transform infrared spectroscopy, X-ray powder diffraction, X-ray photoelectron spectroscopy, Raman spectroscopy and surface area. The content of polycyclic aromatic hydrocarbons (PAHs) (bioavailable Cfree and organic solvent-extractable Ctot), heavy metals (HMs), and environmentally persistent free radicals (EPFRs) were determined. Ecotoxicity was evaluated using tests with Folsomia candida and Allivibrio fischeri. The dependence of adsorption on pyrolysis temperature and composite aging time was observed. Changes in physicochemical properties occurring as a result of aging reduced the adsorption of PO43- on Mg-BC composites. It was found that nonaged Mg-BC700 was more effective (9.55 mg g -1) in the adsorption of PO43- than Mg-BC500 (5.75 mg g-1). The adsorption capacities of aged composites were from 21 to 61% lower than those of the nonaged composites. Due to aging, the content of Cfree PAHs increased by 3-5 times depending on the pyrolysis temperature. However, aging reduced the Ctot PAHs in all composites from 24 to 35% depending on the pyrolysis temperature. Ecotoxicological evaluation of Mg-BC composites showed increased toxicity after aging to both organisms. The use of aged BC potentially increases the contaminant content and toxicity of Mg-BC composites.

Deciphering the photocatalytic degradation of polyaromatic hydrocarbons (PAHs) using hausmannite (Mn3O4) nanoparticles and their efficacy against bacterial biofilm.

Polyaromatic hydrocarbons (PAHs) are life-threatening organic pollutants that severely threaten ecosystems worldwide due to their poisonous qualities, cancer-causing properties, and mutation-causing qualities. Water and soil together form a critical component of the ecosystem that supports all life. Due to the pollutants that are being disposed of in them, their characteristics have changed, and their toxicity has increased. The goal of this study was to investigate the ability of hausmannite nanoparticles to degrade fluorene from soil and water. Using the chemical method, hausmannite nanoparticles were synthesized and further characterization was performed using UV-Vis, FTIR, DLS, XRD, and SEM-EDAX. Hausmannite significantly degraded fluorene using the batch adsorption method. The degradation was also confirmed by performing reactive kinetics using Freundlich's isotherm model and Langmuir's pseudo-second-order model of soil and water. In addition to the degradation efficacy, hausmannite was also proved to inhibit biofilm formation by Pseudomonas aeruginosa. The findings of the experiments confirmed the presence of hausmannite nanoparticles, as well as their physical properties, chemical properties, degradation properties, and parameters of the kinetic study. As a result, synthesized nanoparticles have been extensively utilized as a low-cost option for removing pollutants and microbial biofilm.

Electrochemical remediation of synthetic and real marine sediments contaminated by PAHs, Hg and As under low electric field values.

To date, remediation, protection, and restoration of contaminated sites is a global concern. The current technologies to restore sediments characterized by heterogeneous characteristics, several pollutants, fine grains, and low hydraulic permeability are poorly effective; hence their remediation is still challenging. A promising approach for the sediment's remediation could be the electrochemical route since it is a not-expensive, effective and noninvasive in situ technology. Electrochemical remediation (ER) is commonly studied under relatively high electric fields (E ≥ 1 V cm-1) and using costly processing fluids in a three compartments cell aiming to desorb and transport the contaminants into the processing fluids (secondary dangerous effluent). In this work, contaminated marine sediments were electrochemically treated focusing on the insertion of electrodes directly in the sediments and adopting, for the first time for real sediments, low E values (≤ 0.25 V cm-1) for 4-days period. It was observed that PAHs can be simultaneously transported and degraded in situ preventing the production of a secondary dangerous effluent and reducing the energy consumption. Firstly, clay marine sediments dragged from Capo Granitola Coast (Trapani, Italy) spiked with five PAHs congeners (5PAHs), Hg and As were used as a simplified model matrix and treated to simulate a real case study. A total PAHs removal efficiency of 57% was reached after 96 h of treatment under 0.05 V cm-1. Then, real polluted marine sediments from Augusta Bay (Syracuse) and Bagnoli-Coroglio Bay (Naples) in the southern Italy were treated as real contaminated sediments to be restored, to validate the proposed approach for real cases. A quite good removal efficiency of PAHs was reached after 96 h of electrochemical treatment coupled with a low energetic consumption due to the rather E values adopted. In addition, it was observed that this approach, under the adopted conditions, is unsuitable for the remediation of Hg and As.

Bombé, an undetermined substance that caused an outbreak of illicit drug use in Kinshasa, Democratic Republic of the Congo.

BACKGROUND: Illegal drugs are becoming a public health problem in African cities. In 2021, Bombé, a new drug of unknown composition, caused an outbreak of neuro-psychiatric symptoms in Kinshasa. Bombé was rumored to be based on ground catalytic exhausts stolen from cars. METHODS: The chemical composition of six samples of Bombé obtained from different neighborhoods in Kinshasa was determined by triple quad liquid chromatography-mass spectrometry/mass spectrometry with confirmation by quadrupole time-of-flight mass spectrometry. Metals were determined by inductively coupled plasma-mass spectrometry, and polycyclic aromatic hydrocarbons were measured by gas chromatography-mass spectrometry. RESULTS: Analysis of the Bombé samples revealed that it contained heroin (2-12% of the total area under the curve of the samples) and opioid derivatives, plus paracetamol (33-72%), caffeine (17-26%), and also benzodiazepines (5/6 samples) and cyproheptadine (2/6 samples). The concentrations of neurotoxic metals were unremarkable. The median (range) concentrations of manganese and lead were 9.4 µg/g (range 3-334 µg/g) and 0.36 µg/g (range 0.1-3.12 µg/g ), respectively. All polycyclic aromatic hydrocarbons were below the level of detection (<0.10 µg/g). CONCLUSION: Thanks to international collaboration, Bombé was documented to be a heroin-based drug and its alleged origin from catalytic exhausts was not substantiated. The local human expertise and technical capacity for undertaking toxicological analyses should be increased in Africa.

Effect of carboxyl and hydroxyl groups attached to the benzene ring on the photodegradation of polycyclic aromatic hydrocarbons in ice.

The effect of carboxyl and hydroxyl groups attached to the benzene ring on the photodegradation of anthracene (Ant) and pyrene (Pyr) in ice was investigated. The present study aims to explore the inhibition mechanism of five dissolved organic matter (DOM) model compounds' materials such as benzoic acid, o-hydroxybenzoic acid, m-hydroxybenzoic acid, p-hydroxybenzoic acid, and 3-phenyl propionic acid on the degradation of Ant and Pyr in ice. The photodegradation rate of Ant and Pyr were 50.33 and 37.44% in ice, with the photodegradation rate of Ant being greater than that of Pyr. The five DOM model compounds inhibited the photolysis of Ant and Pyr, and the influence mechanism on the photodegradation of Ant and Pyr depended upon the types and positions of functional groups on the benzene. Among them, the structure in which the carboxyl group was directly connected to the benzene ring and carboxyl was located at the ortho position of a hydroxy group had a strong inhibitory effect on the photodegradation of Ant and Pyr. Light-screening effects and quenching effects were the main inhibiting mechanism, and the binding ability of DOM model compounds material and PAHs is dominantly correlated with its inhibiting effect.

Sepiolite promotes photodegradation of pyrene under visible light.

Mechanochemistry and photocatalysis are emergent technologies for the remediation of polycyclic aromatic hydrocarbons (PAHs) in soils. In this work, mechanochemistry and photocatalysis are combined for pyrene degradation. The photodegradation of pyrene, when in contact with sepiolite under pressure application, is studied. The mechanical treatment leads to a pyrene crystal phase transformation. In this new phase, pyrene undergoes a fast photodegradation in the 320-420 nm range. We show that sepiolite is superior as a photocatalyst in pyrene degradation to TiO2, the most exploited photocatalyst. A broad physicochemical characterization is carried out to propose a mechanism in which the photoexcitation of mechanically altered pyrene leads to an electron transfer to sepiolite matrix, which triggers the PAH degradation. Finally, we want to highlight that the pyrene/sepiolite combination is a simplified system to shed light on how PAH photodegradation may occur in soils.

Novel molecular hybrid geometric-harmonic-Zagreb degree based descriptors and their efficacy in QSPR studies of polycyclic aromatic hydrocarbons.

The physicochemical characteristics of polycyclic aromatic compounds critical to environmental modelling such as octanol partition coefficients, solubility, lipophilicity, polarity and several equilibrium constants are functions of their underlying molecular structures, prompting the development of mathematical models to predict such characteristics for which experimental results are difficult to obtain. We propose twelve novel descriptors derived from geometric, harmonic and Zagreb degree-based descriptors and then test the effectiveness of these descriptors on a data set consisting of 55 benzenoid hydrocarbons of environmental importance. Our computations show that the proposed descriptors have a good linear correlation and predictive power when compared to the degree and distance type descriptors. We have also derived the QSPR expressions for four properties of a large series of polycyclic aromatics arising from circumscribing coronenes and show that a scaling factor can be deduced to derive physicochemical properties of such series up to 2D graphene sheets.