Effectiveness of UV-C radiation in inactivation of microorganisms on materials with different surface structures.

INTRODUCTION AND OBJECTIVE: Ultraviolet light in the UV-C band is known as germicidal radiation and was widely used for both sterilization of the equipment and creation of a sterile environment. The aim of the study is to assess the effectiveness of inactivation of microorganisms deposited on surfaces with various textures by UV-C radiation disinfection devices. MATERIAL AND METHODS: Five microorganisms (3 bacteria, virus, and fungus) deposited on metal, plastic, and glass surfaces with smooth and rough textures were irradiated with UV-C light emitted by low-pressure mercury lamp and ultraviolet emitting diodes (LEDs), from a distance of 0.5 m, 1 m, and 1.5 m to check their survivability after 20-minute exposure. RESULTS AND CONCLUSIONS: Both tested UV-C sources were effective in inactivation of microorganisms; however, LED emitter was more efficient in this respect than the mercury lamp. The survival rate of microorganisms depended on the UV-C dose, conditioned by the distance from UV-C source being the highest at 0.5 m and the lowest at 1.5 m. For the tested microorganisms, the highest survival rate after UV-C irradiation was usually visible on glass and plastic surfaces. This observation should be considered in all environments where the type of material (from which the elements of technical equipment are manufactured and may be contaminated by specific activities) is important for maintaining the proper level of hygiene and avoiding the unwanted and uncontrolled spread of microbiological pollution.

Fast Depolymerization of PET Bottle Mediated by Microwave Pre-Treatment and An Engineered PETase.

Recycling plastics is the key to reaching a sustainable materials economy. Biocatalytic degradation of plastics shows great promise by allowing selective depolymerization of man-made materials into constituent building blocks under mild aqueous conditions. However, insoluble plastics have polymer chains that can reside in different conformations and show compact secondary structures that offer low accessibility for initiating the depolymerization reaction by enzymes. In this work, we overcome these shortcomings by microwave irradiation as a pre-treatment process to deliver powders of polyethylene terephthalate (PET) particles suitable for subsequent biotechnology-assisted plastic degradation by previously generated engineered enzymes. An optimized microwave step resulted in 1400 times higher integral of released terephthalic acid (TPA) from high-performance liquid chromatography (HPLC), compared to original untreated PET bottle. Biocatalytic plastic hydrolysis of substrates originating from PET bottles responded to 78 % yield conversion from 2 h microwave pretreatment and 1 h enzymatic reaction at 30 °C. The increase in activity stems from enhanced substrate accessibility from the microwave step, followed by the administration of designer enzymes capable of accommodating oligomers and shorter chains released in a productive conformation.

Can plastics affect near surface layer ocean processes and climate?

Plastics in the ocean are of great concern nowadays, and are often referred to as the apocalyptic twin of climate change in terms of public fear and the problems they pose to the aquatic and terrestrial environment. The number of studies focusing on the ecological effects and toxicity of plastics has substantially increased in the last few years. Considering the current trends in the anthropogenic activities, the amount of plastics entering the world oceans is increasing exponentially, but the oceans have a low assimilative capacity for plastics and the near-surface layer of it is a finite space. If loading of the oceans with plastics continues at the current rate, the thin sea surface microlayer can have a substantial amount of plastics comparable to the distribution of phytoplankton, at least in the major oceanic gyres and coastal waters in the future. Also, processes like biofouling can cluster microplastics in dense fields in the near-surface layer. Plastics can contribute to the warming or cooling of the water column by scattering and attenuating incoming solar radiation, leading to a potential change in the optical and other physico-chemical properties of the water column. We propose a new notion that changes in solar radiation in the water column due to the plastics have the potential to affect the physical processes in the ocean surface and near-surface layers, and can induce climate feedback cycles. The future can be very different, if plastics evolve as one of the key players affecting the ocean physical processes and hence this is the time to tackle this puzzle with appropriate strategies or let the genie out of the bottle.

Outdoor manufacture of UV-Cured plastic linings for storm water culvert repair: Chemical emissions and residual.

Storm water culverts are integral for U.S. public safety and welfare, and their mechanical failure can cause roadways to collapse. To repair these buried assets, ultraviolet (UV) light cured-in-place-pipes (CIPP) are being installed. Chemical emission and residual material left behind from the installation process was investigated in New York and Virginia, USA. Samples of an uncured resin tube and field-cured styrene-based resin CIPPs were collected and analyzed. Also collected were air and water samples before, during, and after installations. Chemicals were emitted into air because of the installation and curing processes. Particulates emitted into the air, water, and soil contained fiberglass, polymer, and contaminants, some of which are regulated by state-level water quality standards. The uncured resin tube contained more than 70 chemical compounds, and 19 were confirmed with analytical standards. Compounds included known and suspected carcinogens, endocrine disrupting compounds, hazardous air pollutants, and other compounds with little aquatic toxicity data available. Compounds (14 of 19 confirmed) were extracted from the newly installed CIPPs, and 11 were found in water samples. Aqueous styrene (2.31 mg/L), dibutyl phthalate (12.5 µg/L), and phenol (16.7 µg/L) levels exceeded the most stringent state water quality standards chosen in this study. Styrene was the only compound that was found to have exceed a 48 h aquatic toxicity threshold. Newly installed CIPPs contained a significant amount volatile material (1.0 to > 9.0 wt%). Recommendations provided can reduce chemical emission, as well as improve worksite and environmental protection practices. Recommended future research is also described.

Comparisons of analytical chemistry and biological activities of extracts from North Pacific gyre plastics with UV-treated and untreated plastics using in vitro and in vivo models.

Plastic debris is an emerging worldwide threat to marine biota. Marine species may face unique challenges in low-flow estuarine systems with a high abundance of "macro-sized" (>4.75 mm) plastic due to the leaching of constituents and adsorbed contaminants. To simulate this leaching process, plastic samples recovered from the North Pacific Gyre along with corresponding UV-irradiated virgin plastic and non-irradiated virgin plastic counterparts were incubated in saltwater for 30 days at ambient temperatures ranging from 17 to 25 °C. Following solid-phase extraction, water samples were fractionated with sequential methanol elution from 10 to 100% and evaluated using in vitro assays assessing estrogen receptor (ER) and aryl hydrocarbon receptor (AhR) activities. In vivo responses (vitellogenin [vtg] and cytochrome p450 1A [cyp1a] mRNA) were measured following 5-day exposures in Japanese medaka (Oryzias latipes) larvae (3 days post hatch). Estrogenic plasticizers, co-planar PCBs and PAHs were quantified in the extracts using targeted GC-MS/MS and UPLC-MS/MS. In vitro estrogenicity showed highest activity in the 70% methanol fraction for all plastic leachate exposures. Whole extract in vitro estradiol equivalent (EEQ) values were 4.34 ±â€¯2.65, 8.79 ±â€¯2.09 and 13.78 ±â€¯3.64 ng/L, for virgin plastic, UV-irradiated virgin plastic and North Pacific Gyre-recovered plastic, respectively (mean ±â€¯SD). Significant vtg induction was observed in medaka larvae exposed to leachate extracts from North Pacific Gyre-recovered plastic and UV-irradiated virgin plastic (9.9-fold, p = 0.039 and 10.1-fold, p = 0.042, respectively). Chemically-determined EEQ values were also localized in the 70% methanol fraction. Whole leachate extract chemical EEQ values were 0.33 ±â€¯0.07, 1.64 ±â€¯0.62 and 11.4 ±â€¯2.13 ng/L, for virgin plastic, UV-irradiated virgin plastic and North Pacific Gyre-recovered plastic, respectively. In-vitro AhR activity was highest in the 70% methanol elution with greater activity in North Pacific Gyre-recovered plastic than in virgin plastic and UV-irradiated virgin plastic (toxic equivalency [TEQ] = 1.06 ±â€¯0.54, 0.38 ±â€¯0.07 and 0.71 ±â€¯0.47 ng/L, respectively). CYP1A mRNA was significantly induced in larval medaka exposed to North Pacific Gyre-recovered plastic leachates (17.8-fold, p = 0.02) while exposure to virgin plastic and UV-irradiated virgin plastic leachates caused no significant change. Chemically-determined TEQ analysis for AhR indicated highest activity in the 90% methanol fraction for all leachates, with whole extract in vitro TEQs being 1.47 ±â€¯0.87, 0.03 ±â€¯0.05 and 0.42 ±â€¯0.38 ng/L for North Pacific Gyre-recovered plastic, virgin plastic and UV-irradiated virgin plastic, respectively. These results indicate that weathering and UV radiation release estrogenic plasticizers and demonstrate the ability for plastics to transport adsorbed persistent organic pollutants at eco-toxicologically relevant concentrations.

Dissolved organic carbon leaching from plastics stimulates microbial activity in the ocean.

Approximately 5.25 trillion plastic pieces are floating at the sea surface. The impact of plastic pollution on the lowest trophic levels of the food web, however, remains unknown. Here we show that plastics release dissolved organic carbon (DOC) into the ambient seawater stimulating the activity of heterotrophic microbes. Our estimates indicate that globally up to 23,600 metric tons of DOC are leaching from marine plastics annually. About 60% of it is available to microbial utilization in less than 5 days. If exposed to solar radiation, however, this DOC becomes less labile. Thus, plastic pollution of marine surface waters likely alters the composition and activity of the base of the marine food webs. It is predicted that plastic waste entering the ocean will increase by a factor of ten within the next decade, resulting in an increase in plastic-derived DOC that might have unaccounted consequences for marine microbes and for the ocean system.

Evaluation of the migration of chemicals from baby bottles under standardised and duration testing conditions.

After the prohibition of bisphenol-A-containing polycarbonate baby bottles in the European Union (EU), alternative materials, such as polypropylene, polyethersulphone, Tritan™ copolyester, etc., have appeared on the market. Based on an initial screening and in vitro toxicity assessment, the most toxic migrating compounds were selected to be monitored and quantified using validated GC- and LC-QqQ-MS methods. The effect of several 'real-life-use conditions', such as microwave, sterilisation and dishwasher, on the migration of different contaminants was evaluated by means of duration tests. These results were compared with a reference treatment (filling five times with pre-heated simulant at 40°C) and with the legal EU 'repetitive-use conditions' (three migrations, 2 h at 70°C). Analysis of the third migration step of the EU repetitive-use conditions (which has to comply with the EU legislative migration limits) showed that several non-authorised compounds were observed in some baby bottles exceeding 10 µg kg(-1). However, all authorised compounds were detected well below their respective specific migration limits (SMLs). The reference experiment confirmed the migration of some of the compounds previously detected in the EU repetitive-use experiment, though at lower concentrations. Analysis of extracts from the microwave and dishwasher experiments showed a reduction in the migration during the duration tests. In general, the concentrations found were low and comparable with the reference experiment. Similar observations were made for the two sterilisation types: steam and cooking sterilisation. However, steam sterilisation seems to be more recommended for daily use of baby bottles, since it resulted in a lower release of substances afterwards. Repeated use of baby bottles under 'real-life' conditions showed no increase in the migration of investigated compounds and, after some time, the migration of these compounds even became negligible.

Efficacy of UV-C irradiation for inactivation of food-borne pathogens on sliced cheese packaged with different types and thicknesses of plastic films.

In this study, the efficacy of using UV-C light to inactivate sliced cheese inoculated with Escherichia coli O157:H7, Salmonella Typhimurium, and Listeria monocytogenes and, packaged with 0.07 mm films of polyethylene terephthalate (PET), polyvinylchloride (PVC), polypropylene (PP), and polyethylene (PE) was investigated. The results show that compared with PET and PVC, PP and PE films showed significantly reduced levels of the three pathogens compared to inoculated but non-treated controls. Therefore, PP and PE films of different thicknesses (0.07 mm, 0.10 mm, and 0.13 mm) were then evaluated for pathogen reduction of inoculated sliced cheese samples. Compared with 0.10 and 0.13 mm, 0.07 mm thick PP and PE films did not show statistically significant reductions compared to non-packaged treated samples. Moreover, there were no statistically significant differences between the efficacy of PP and PE films. These results suggest that adjusted PP or PE film packaging in conjunction with UV-C radiation can be applied to control foodborne pathogens in the dairy industry.

Time resolution of the plastic scintillator strips with matrix photomultiplier readout for J-PET tomograph.

Recent tests of a single module of the Jagiellonian Positron Emission Tomography system (J-PET) consisting of 30 cm long plastic scintillator strips have proven its applicability for the detection of annihilation quanta (0.511 MeV) with a coincidence resolving time (CRT) of 0.266 ns. The achieved resolution is almost by a factor of two better with respect to the current TOF-PET detectors and it can still be improved since, as it is shown in this article, the intrinsic limit of time resolution for the determination of time of the interaction of 0.511 MeV gamma quanta in plastic scintillators is much lower. As the major point of the article, a method allowing to record timestamps of several photons, at two ends of the scintillator strip, by means of matrix of silicon photomultipliers (SiPM) is introduced. As a result of simulations, conducted with the number of SiPM varying from 4 to 42, it is shown that the improvement of timing resolution saturates with the growing number of photomultipliers, and that the [Formula: see text] configuration at two ends allowing to read twenty timestamps, constitutes an optimal solution. The conducted simulations accounted for the emission time distribution, photon transport and absorption inside the scintillator, as well as quantum efficiency and transit time spread of photosensors, and were checked based on the experimental results. Application of the [Formula: see text] matrix of SiPM allows for achieving the coincidence resolving time in positron emission tomography of [Formula: see text]0.170 ns for 15 cm axial field-of-view (AFOV) and [Formula: see text]0.365 ns for 100 cm AFOV. The results open perspectives for construction of a cost-effective TOF-PET scanner with significantly better TOF resolution and larger AFOV with respect to the current TOF-PET modalities.

Systematic evaluation of photodetector performance for plastic scintillation dosimetry.

PURPOSE: The authors' objective was to systematically assess the performance of seven photodetectors used in plastic scintillation dosimetry. The authors also propose some guidelines for selecting an appropriate detector for a specific application. METHODS: The plastic scintillation detector (PSD) consisted of a 1-mm diameter, 10-mm long plastic scintillation fiber (BCF-60), which was optically coupled to a clear 10-m long optical fiber of the same diameter. A light-tight plastic sheath covered both fibers and the scintillator end was sealed. The clear fiber end was connected to one of the following photodetectors: two polychromatic cameras (one with an optical lens and one with a fiber optic taper replacing the lens), a monochromatic camera with an optical lens, a PIN photodiode, an avalanche photodiode (APD), or a photomultiplier tube (PMT). A commercially available W1 PSD was also included in the study, but it relied on its own fiber and scintillator. Each PSD was exposed to both low-energy beams (120, 180, and 220 kVp) from an orthovoltage unit and high-energy beams (6 and 23 MV) from a linear accelerator. Various dose rates were tested to identify the operating range and accuracy of each photodetector. RESULTS: For all photodetectors, the relative uncertainty was less than 5% for dose rates higher than 3 mGy/s. The cameras allowed multiple probes to be used simultaneously, but they are less sensitive to low-light signals. The PIN, APD, and PMT had higher sensitivity, making them more suitable for low dose rate and out-of-field dose monitoring. The relative uncertainty of the PMT was less than 1% at the lowest dose rate achieved (0.10 mGy/s), suggesting that it was optimal for use in live dosimetry. CONCLUSIONS: For dose rates higher than 3 mGy/s, the PIN diode is the most effective photodetector in terms of performance/cost ratio. For lower dose rates, such as those seen in interventional radiology or high-gradient radiotherapy, PMTs are the optimal choice.