Surface roughness and cyclic fatigue resistance of a novel shaping system: An in-vitro study.

Recently developed Nickel-Titanium (NiTi) instruments with practical changes have resulted in safer instrumentation. In addition, topographical features on the file surface are a contributing factor to clinical durability. Therefore, this study aimed to investigate both the cyclic fatigue resistance and the roughness change of MTwo and Rotate instruments (VDW, Munich, Germany). Each instrument (n = 6/each group) was scanned with an atomic force microscopy prior to and after instrumentation. In addition, cyclic fatigue testing was conducted for each instrument (n = 11/each group) with stainless-steel blocks, including 45°-60°-90° degrees of curvature milled to the instruments' size. The roughness parameters increased for both systems after instrumentation (p<0.05). Both systems presented an increased roughness following instrumentation (p<0.05). The cyclic fatigue resistance was lowest at 90° for both systems (p<0.05), whereas the Rotate files presented a higher resistance than that of the Mtwo files (p<0.05). Compared to the Mtwo files, Rotate files presented better resistance, while the resistance decreased as the curvature increased.

Volumetric Analysis of Hand and Rotary Instrumentation, Root Canal Filling Techniques, and Obturation Materials in Primary Teeth Using Spiral CT.

AIM AND BACKGROUND: To compare the root canal volume in primary teeth using hand and rotary instruments and to evaluate root canal filling techniques and flow of root canal obturation materials in the postinstrumented root canal volume using spiral computed tomography (SCT). MATERIALS AND METHODS: Freshly extracted 16 primary molars were randomly divided into two groups and subjected to SCT analysis before and after instrumentation. For the manual technique (group I) with eight teeth were prepared using K files, and rotary (group II) eight teeth preparation was performed with ProTaper files. The filled volume in each canal was measured using SCT, and the percentage of obturated volume was calculated. The data were statistically analyzed using the Mann-Whitney U test. RESULTS: There was a statistically significant difference in both groups' volume of root canals enlarged. Even though both K files and the ProTaper system brought about enlarged canals after instrumentation, there was a statistically significant increase in volume after using K files in two canals. In three canals, there was a statistically significant increase in volume after using ProTaper. Irrespective of the obturation technique and materials used, there is no statistically significant difference in the volume after obturation. CONCLUSION: From the results of this study, the ProTaper file system shows suitable volumetric enlargement up to an optimum level, which is needed in primary root canal walls, and is better in canal shaping, as evidenced by good postobturation volume. CLINICAL SIGNIFICANCE: The traditional method of cleaning and shaping the root canals in permanent teeth using manual stainless-steel files can lead to undesirable curvatures in root canal morphology, making correctly filling the root canals difficult. It is also time-consuming and sometimes leads to iatrogenic errors. Rotary nickel-titanium (Ni-Ti) instrumentation techniques have been developed to overcome these problems. How to cite this article: Yadav DBUC, Varma RB, Kumar JS, et al. Volumetric Analysis of Hand and Rotary Instrumentation, Root Canal Filling Techniques, and Obturation Materials in Primary Teeth Using Spiral CT. J Contemp Dent Pract 2024;25(3):250-259.

Phase-locked µPIV analysis of flow dynamics in a simulated root canal with different laser-activated irrigations.

PURPOSE: To measure the dynamic characteristics of the flow field in a complex root canal model activated by two laser-activated irrigation (LAI) modalities at different activation energy outputs: photon-induced photoacoustic streaming (PIPS) and microshort pulse (MSP). METHODS: A phase-locked micro-scale Particle Image Velocimetry (µPIV) system was employed to characterise the temporal variations of LAI-induced velocity fields in the root canal following a single laser pulse. The wall shear stress (WSS) in the lateral root canal was subsequently estimated from the phase-averaged velocity fields. RESULTS: Both PIPS and MSP were able to generate the 'breath mode' of the irrigant current under all tested conditions. The transient irrigation flush in the root canal peaked at speeds close to 6 m/s. However, this intense flushing effect persisted for only about 2000 µs (or 3% of a single laser-pulse activation cycle). For MSP, the maximum WSS magnitude was approximately 3.08 Pa at an activation energy of E = 20 mJ/pulse, rising to 9.01 Pa at E = 50 mJ/pulse. In comparison, PIPS elevated the WSS to 10.63 Pa at E = 20 mJ/pulse. CONCLUSION: Elevating the activation energy can boost the peak flushing velocity and the maximum WSS, thereby enhancing irrigation efficiency. Given the same activation energy, PIPS outperforms MSP. Additionally, increasing the activation frequency may be an effective strategy to improve irrigation performance further.

Atypical healing of an endodontic lesion following emergency treatment: a case report.

This case report examines the atypical healing of an endodontic lesion without standard endodontic treatment, influenced by the patient's failure to attend treatment appointments. A 50-year-old woman with no notable medical history presented with a deep carious lesion on her mandibular right first molar, accompanied by localized pain. Citing forgetfulness as a reason, the patient missed her initially scheduled root canal treatment, necessitating an emergency intervention. The emergency treatment included access cavity preparation, irrigation with 5.25% sodium hypochlorite solution, application of a modified triple antibiotic paste (equal parts penicillin G, metronidazole, and ciprofloxacin), and temporary restoration with amalgam. A large apical lesion was detected in immediate postoperative radiographs. However, the patient failed to return for definitive endodontic treatment, due to a lack of symptoms and time for treatment. Follow-up examinations 1 and 5 years after emergency treatment disclosed gradual healing of the lesion, culminating in the establishment of a normal periodontal ligament. This case underscores the potential efficacy of a modified triple antibiotic paste and highlights the importance of a well-sealed coronal restoration in promoting the healing of endodontic lesions, even in the absence of pulpectomy and conventional root canal therapy. Additional research is needed to understand the mechanisms behind such healing events.

Post-endodontic pain in curved canals prepared with different rotary instrumentation techniques: A randomized controlled trial.

BACKGROUND: Curved root canals are associated with the highest number of procedural errors during endodontic instrumentation. Recently, numerous rotary instruments have been developed, with both manual and automated mechanisms, to facilitate endodontic treatment and manage the complications related to it. OBJECTIVES: The aim of the study was to assess post-endodontic pain after using the HyFlex® EDM OneFile (HEDM), WaveOne® Gold (WOG) and XP-endo® Shaper (XPS) systems in the preparation of curved canals in patients with asymptomatic irreversible pulpitis. MATERIAL AND METHODS: A total of 45 molars with curved canals and asymptomatic irreversible pulpitis were randomly divided into 3 equal groups based on the instrumentation used: HEDM (group A); WOG (group B); and XPS (group C). All teeth were prepared according to the manufacturers' instructions. Postendodontic pain was assessed using the visual analog scale (VAS) at 6, 12, 18, 24, 48, and 72 h after root canal instrumentation. The data was analyzed using the one-way analysis of variance (ANOVA) and the paired-samples t test with the Bonferroni correction, with a p-value of 0.05 set for statistical significance. RESULTS: The highest levels of post-endodontic pain were recorded at 6 h after treatment. Then, the values gradually decreased until the pain nearly vanished after 72 h. No statistically significant differences were observed in the VAS scores between groups A and B. At the same time, group C showed the lowest VAS scores at all follow-up time points. CONCLUSIONS: The use of the XPS system resulted in the lowest pain scores at all follow-ups. The HEDM and WOG groups showed no differences in the pain scores throughout the whole follow-up period.

Factors influencing NiTi endodontic file separation: A thematic review.

Nickel-titanium (NiTi) file separation during endodontic treatment is an undesirable event. This phenomenon needs to be understood by knowing the factors influencing fracture in endodontic files. There is a large amount of literature where these factors and their influence have been studied, increasing the knowledge about the mechanisms involved, mainly related to wire technology, file shapes and geometry, operator manipulation, the anatomy of the root canal, and the irrigation and sterilization processes. As many factors are involved, the complexity of the fracture phenomena increases and the isolated correlation of one factor with the file fracture becomes a small part of comprehending the separation phenomena. This thematic review aims to compile important reports from 2014 to 2022 on the factors influencing NiTi file separation. The information obtained was classified into wire technology, file geometry, operational aspects, irrigation and sterilization, and anatomy. For this purpose, the Scopus, Web of Science and ScienceDirect databases were consulted using a search string. Filters were applied to consolidate the final set of relevant papers covering the subject of factors influencing endodontic file separation. It was found that the fracture of NiTi files incorporates different mechanisms that operate simultaneously during the endodontic procedure and strongly affect the instrument performance. The collected information promotes good practices to prevent file separation.

Postoperative pain after single-visit root canal treatments in necrotic teeth comparing instruments' kinematics and apical instrumentation limits - a prospective randomized multicenter clinical trial.

OBJECTIVES: This prospective randomized multicenter clinical trial (PRMCT) investigated postoperative pain after single-visit root canal treatments in teeth affected by pulp necrosis (PN), and asymptomatic apical periodontitis (AAP) (with apical radiolucent areas) or normal periradicular tissues (without apical radiolucent areas) comparing different instruments' kinematics and apical instrumentation limits. METHODS: Before chemomechanical preparation, 240 patients/teeth were randomly distributed into four groups (n = 60) according to the instruments' kinematics (rotary or reciprocating) and apical instrumentation limits (with or without intentional foraminal enlargement [IFE]). After that, specimens were submitted to the same irrigation and obturation techniques, and the patients were referred to undergo the definitive restorations. No medication was prescribed, but the patients were instructed to take either paracetamol (750 mg every 6 h for three days) or ibuprofen (600 mg every 6 h for three days) in pain cases. Postoperative pain incidence and levels were assessed at 24-, 48-, and 72 h following treatment completion according to a verbal rating scale (VRS) following a score. The Kolmogorov-Smirnov test was applied to assess the normality of the data. Mann-Whitney U, Chi-square, Friedman's ANOVA, and Friedman's multiple 2 to 2 comparison tests were employed to identify potential significant statistical differences among the variables in the study groups (P < .05). RESULTS: Significant statistical differences were only observed among the groups considering tooth, periradicular status, and the occurrence of overfilling (sealer extrusion) (P < 0.00). Patients with teeth instrumented through rotary kinematics and without IFE experienced lower rates of postoperative pain; however, this difference was relevant only at 24 h (P < 0.05). CONCLUSIONS: Postoperative pain was lower after using a rotary file system (Profile 04) inserted up to the apical constriction (AC). However, this finding was just statistically meaningful at 24 h. TRIAL REGISTRATION: This PRMCT was approved by the Human Research Ethics Committee of the Paranaense University - UNIPAR, Francisco Beltrão, PR, Brazil (CAAE. 46,774,621.6.0000.0109) on 02/09/2021. It was registered at The Brazilian Registry of Clinical Trials - ReBEC (RBR-3r967t) on 01/06/2023, was performed according to the Principles of the Helsinki Declaration and is reported following the Consolidated Standards of Reporting Trials Statement.

Micro-computed tomographic evaluation on the quality of single-cone obturation using a modified passive-deflation sealer injection needle: an in vitro study.

OBJECTIVES: This study aimed to design a modified passive-deflation sealer injection needle and investigate its ability to improve obturation quality of single-cone technique through assessing the distribution of voids in root canals using micro-computed tomography (micro-CT). MATERIALS AND METHODS: Forty-eight mandibular incisors were divided into eight groups (n = 6), according to the taper of root canal preparation (0.06 or 0.04), the needle used for sealer injection (modified or commercial iRoot SP injection needle), and the obturation method (iRoot SP sealer-only or single-cone obturation). After obturation, each specimen was scanned by micro-CT. The volumetric percentage and distribution of all voids were first analyzed and compared among groups, then the open and closed voids were separately analyzed and compared among single-cone obturation groups. RESULTS: Compared to commercial needle groups, modified needle groups showed much less voids, especially in the apical root canal part (P < 0.05). Besides, the modified needle groups produced much less open voids than commercial needle groups despite the root canal taper (P < 0.05). CONCLUSIONS: The modified passive deflation sealer injection needle could effectively improve the quality of single-cone obturation through reducing intra-canal voids, especially open voids throughout the root canal, thus might possibly be developed as an effective intra-canal sealer delivering instrument.

[Comparison of the ability of four different kinds of nickel-titanium instruments to prepare simulated resin to simulate curved root canal forming].

PURPOSE: To compare the forming ability of four kinds of nickel-titanium instrument preparation resin for simulated curved root canal. METHODS: A total of 40 single bend resin simulated root canals were randomly divided into 4 groups with 10 in each group. Four kinds of nickel-titanium instruments (ProTaper, HyFlex EDM, WaveOne Gold and Reciproc Blue) were used for root canal preparation, and divided into group A, group B, group C and group D. The preparation time of the four groups was compared, the root canal images before and after preparation were analyzed by computer image analysis software, and the changes of the preparation time, curvature and curvature radius of the four groups were recorded. With the root tip as the center of the circle, the radius of 1-10 mm was selected as concentric circle arcs. The detection points were overlapping root canal intersection points. The resin removal amount and center positioning force of the inner and outer walls of the root canal at different detection points were recorded. Statistical analysis was performed with SPSS 20.0 software package. RESULTS: The root canal preparation time in group A was significant longer than that in group B, C and D(P＜0.05), but there was no significant difference in the curvature and curvature radius of the root canal among the four groups (P＞0.05). The removal amount of resin from the root canal wall in group C was significant lower than that in group A, B and D (P＜0.05) when the distance from the detection point to the apical foramina was 5, 6, 8, 9 and 10 mm, respectively. The removal amount of resin from the outer wall of the root canal in group C was significant lower than that in group A, B and D (P＜0.05) when the distance from the detection point to the apical foramina was 5, 6, 7, 9 and 10 mm, respectively. The root tip offset of group A from the detection point to the apical hole of 1, 2, 3, 4, 6, 7, 8, 9 and 10 mm was significant greater than that of group B, C and D(P＜0.05). CONCLUSIONS: Among the four instruments, ProTaper has the largest apical deviation, HyFlex EDM, WaveOne Gold and Reciproc Blue have better ability of root canal forming.

Microcomputed tomography analysis of curved root canal preparation when coronal flaring and glide path files used with heat-treated nickel titanium rotary files.

The objective was to evaluate the effect of glide path and coronal flaring on the dentin volume removal and percentage of touched walls in curved canals using two heat-treated rotary files. The mesiobuccal canal of forty-eight, randomly selected, extracted mandibular molars was divided into two groups of 24 each, according to the type of instrument used (RACE EVO and EdgeSequel rotary files). Each group was further divided into three subgroups; Group (A): Control using one file shaped to 04/30, Group (B) with a glide path (EdgeGlidePath (EGP)), and Group (C): with a glide path and coronal flaring (EGP and EdgeTaper Platinum (ETP) SX file respectively). The root canals were then instrumented using the assigned instruments. The assessment was carried out using micro-CT. The comparison of the mean values of the tested groups about dentin volume removal and percentage of untouched walls did not reach statistical significance (p<0.05). Glide path and coronal flaring had an insignificant effect on the dentin volume removal and percentage of untouched walls in curved canals.

Comparative evaluation of ethanol versus citric acid in removal of oil-based calcium hydroxide from the apical third of root canal system.

Objectives: To evaluate the effectiveness of ethanol compared to citric acid in the removal of oil-based calcium hydroxide from the apical third of the root canal system using passive ultrasonic irrigation. METHODS: The in vitro study was conducted from September to October 2021 at the dental clinics of the Aga Khan University Hospital, Karachi, and comprised single-rooted teeth that were selected from institutional bank of extracted teeth. They were randomly divided into group A having 70% ethanol + passive ultrasonic irrigation, group B 10% citric acid + passive ultrasonic irrigation, group C positive controls and group D negative controls. The specimens were sectioned at 1mm and 3mm from the apex and examined under a dental operating microscope. A single examiner scored the specimens on two different occasions. Data was analysed using SPSS 25. RESULTS: Of the 90 teeth, there were 40(44.4%) in each of the 2 experimental groups and 5(5.5%) in each of the 2 control groups. At 3mm apical sections, ethanol was significantly more effective in the removal of oil-based calcium hydroxide (p=0.01). However, at 1mm from the apex, there was no significant difference between the experimental groups (p=0.064). Intragroup comparison showed that for groups A and B, residual medicament at 1mm sections was significantly greater than at 3mm sections (p<0.001, p=0.003). CONCLUSIONS: Neither irrigant showed complete removal at 1mm and 3mm from the apex. However, at 3mm apical sections, 70% ethanol was significantly more effective compared to 10% citric acid.

Evaluation of Postoperative Pain after Using Dexamethasone Intracanal Rinse in Irreversible Pulpitis.

OBJECTIVE: To evaluate the efficacy of dexamethasone as a final intracanal rinse in relieving postoperative pain of teeth with symptomatic irreversible pulpitis. STUDY DESIGN: Randomised controlled trial. Place and Duration of the Study: Department of Operative Dentistry, PIMS, Islamabad, Pakistan, from June 2019 to December 2020. METHODOLOGY: Sixty patients aged 18- 50 years diagnosed with symptomatic irreversible pulpitis were selected according to the inclusion criterion. After obtaining informed consent, root canal therapy (RCT) was initiated under rubber dam. Pulpectomy was done followed by canal preparation. The lottery method was utilised for the division of patients. Group A (experimental) received dexamethasone (4mg/ml in 5ml syringe) as a final rinse, while Group B (control group) recalled after 1 week and asked whether their pain had relieved or not as a yes/no question. After data collection teeth were obturated and permanent restoration was placed. Data were analysed using Chi-square test. RESULTS: The efficacy of dexamethasone as a final intracanal rinse was greater than saline 86.67% and 20.0%, respectively (p < 0.05) in relieving postoperative pain in teeth with symptomatic irreversible pulpitis. CONCLUSION: Dexamethasone was proved to be more efficacious than saline in alleviating postoperative pain when used as a final intracanal rinse after canal instrumentation. KEY WORDS: Irreversible pulpitis, Dexamethasone, Postoperative pain, Pulpectomy.

Influence of Different Glide Path Techniques on Microcrack Formation after Two Different Root Canal Preparation Treatments: Micro Computed Tomography Analysis.

OBJECTIVE: This study aimed to evaluate the effect of WaveOne Glider (WOGG) with Waveone Gold (WOG) primary reciprocation systems on root dentine microcrack formation and to know the effect of TruNatomy Glider (TRNG) with TruNatomy (TRN) prime rotary systems on root dentine microcrack formation. METHODS: In this study, 40 extracted mandibular first molar roots were selected and divided randomly into four groups (n=10). Group MWOG: a manual glide path was performed + WOG primary. Group MTRN: manual glide path performed+TRN prime. Additionally, group WOGG: glide path preparation with WOGG+WOG primary. Finally, for group TRNG, the glide path preparation was performed with TRNG+TRN prime. Micro-CT was used for pre and post-instrumentation image analysis. Statistical analysis was performed using the Kruskal- Wallis test (p<0.05) with Two-way ANOVA. RESULTS: The Kruskal-Wallis test showed no significant differences among all groups in all thirds for pre and post-instrumentation regarding the crack formation. The Two-way ANOVA showed no significant difference or interaction between the ways of glide path preparation, whether manual or reciprocal WOGG, or between the rotary TRNG and the motion used in root canal preparation (rotary TRN or reciprocal WOG) regarding the crack formation and propagation. CONCLUSION: Microcrack formation and propagation occurred independently of using different glide path techniques (manual, rotary, or reciprocal).

Root canal curvature influences uncontrolled removal of dentin and cleaning efficacy after ultrasonic activation.

This study evaluated the correlation between root canal curvature and the effects of ultrasonic irrigation in the following parameters: volume of uncontrolled dentin removal (UDRVol), maximum depth of dentin defects, removal of accumulated hard tissue debris (AHTD), and canal transportation in prepared curved root canals. Twenty-four human permanent mandibular molars were divided into two groups according to root canal curvature: moderate curvature (MC: mean 25°); and severe curvature (SC: mean 48°). The specimens were scanned using an X-ray microcomputed scanner (Skyscan 1172) before and after cleaning and shaping and after the final irrigation protocol with ultrasonic irrigation. There was a moderate correlation between the degree of root canal curvature and the volume of remaining AHTD (p<0.05) and between the degree of root canal curvature and maximum depth of defects due to uncontrolled removal of dentin (p<0.05). The teeth in the SC group had a greater maximum depth of defects on the dentin wall in the apical third than the teeth in the MC group (p <0.05). Both groups had a significant reduction of AHTD in all canal thirds, but the amount of remaining AHTD in the middle and apical thirds and the whole canal was significantly greater in the SC than in the MC group (p <0.05). Canal transportation was not influenced by the canal curvature in all thirds (p >0.05). This study concluded that root canal curvature affects significantly the uncontrolled removal of dentin and remaining AHTD volume after the final irrigation protocol with ultrasonic irrigation.

Postendodontic Pain Using Single File System with Different Irrigation Protocols in Single-visit Root Canal Treatment: A Randomized Control Trial.

AIM: To evaluate the intensity of postendodontic pain (PEP) using final irrigation with side-vented needle (SV), EndoActivator (EA), and Ultra X (UX) in single-visit endodontics (SVE) with F-One rotary files. MATERIALS AND METHODS: A total 150 patients indicated for endodontic treatment were selected. Single-visit endodontics treatment was performed under local anesthesia. For the final irrigation protocol, they were divided into three groups: group I (SV), group II (EA), and group III (UX). The severity of PEP was assessed using visual analogue scale (VAS) score after 6, 12, 24, and 48 hours. Analgesics taken by patients, for pain, were also recorded. Finally, the data were tabulated and statistically analyzed using SPSS 20.0 software at a level of significance being 0.05. RESULTS: Postendodontic pain was less in group III (UX) and group II (EA) compared with group I (SV) at 6 and 12 hours, which is statistically significant (p < 0.05). There was no statistically significant difference found after 24 hours and 48 hours. CONCLUSION: The intensity of PEP was minimum in patients treated with EndoActivator and ultrasonic along with single rotary file systems. The incidence of analgesic intake was similar in all three groups. How to cite this article: Kathiria NV, Attur K, Bagda KM, et al. Postendodontic Pain Using Single File System with Different Irrigation Protocols in Single-visit Root Canal Treatment: A Randomized Control Trial. J Contemp Dent Pract 2024;25(2):180-185.

The evaluation of effective rate and pain intensity of root canal treatment in primary teeth-a retrospective study.

Two-visit root canal treatment for children reduce the time of visits and the by-chair time in comparison with the three-visit root canal treatment. However, it is not clear whether two-visit root canal treatment increase the risk of complications. This study aimed to evaluate the clinical effects and post-operative pain intensity after the root canal treatment between two-visit and three-visit groups in primary molars from children.106 patients were screened for eligibility, of which 74 went back to the preservation visit. Therefore, 74 primary molars from 74 children that diagnosed with chronic pulp and periodontal tissue diseases in the clinics of pediatric dentistry were retrospectively analyzed, in which 37 in the two-visit group and 37 in the three-visit group. The total effective rate and postoperative pain intensity were assessed after treatment and all statistical data were carried out with SPSS software.The average age of children in the two-visit and three-visit groups was 6.4 and 7.0, respectively, with no significant difference (p = 0.056). The two-visit group consisted of 59.5% male and 40.5% female children, while the three-visit group consisted of 56.8% male children and 43.2% female children (p = 0.813). Two months after treatment, the total effective rate in the three-visit group was 97.30%, a little higher than that in the two-visit group (94.59%), but with no significant difference (p = 0.201). Besides, there was also no significant difference in pain intensity between the two-visit and three-visit groups (p = 0.692). Therefore, there were no significant difference of total effective rate and pain intensity in root canal treatment between the two-visit and three-visit groups in primary molars from children.

Comparative evaluation of volumetric changes between two pediatric rotary files (Kedo-S plus, Kedo-SG blue) and manual files (hand K-files) during canal preparation of primary mandibular molars: an in-vitro nano-CT analysis.

Pediatric endodontics has become popular due to advancements in cleaning, shaping and irrigation systems, resulting in faster and effective removal of infected pulp, saving time, and creating a pathogen-free environment. The patented rotary file system, Kedo-S, designed for primary teeth, introduced a single file generation for efficient pulp therapy. However, there are currently no studies assessing canal preparation in primary mandibular molars using nano-CT (computed Tomography). To evaluate the volumetric changes of two recently introduced pediatric rotary file systems in comparison with conventional hand file systems in primary mandibular molar using an ultra-high resolution nano-CT. This in-vitro study was performed in extracted primary mandibular molar based on certain inclusion and exclusion criteria. Samples were prepared and working length was determined before the pre-operative scan using a high resolution nano-CT device (SkyScan 2214, Bruker, Kontich, Belgium). A single well-experienced pediatric dentist prepared the canals using three file systems: Kedo-S plus, Kedo-SG blue and Hand K-files. A post-operative scan was performed similar to pre-operative scan. Image reconstruction was performed with NRecon software for 3D volumetric visualization and analysis of the root canals. Kedo-SG blue file systems had the highest mean difference in the canal volume (8.85%). Hand K-files had the least difference at (1.24%) of canal volume. Kedo-S plus file system had a mean canal volume difference (6.14%) which is closer to hand K-files. Rotary file systems resulted in a significant enlargement of canals compared to hand files.

The influence of laser-activated irrigation on post-operative pain following root canal treatment: A systematic review.

OBJECTIVES: Synthesise evidence on post-endodontic pain (PEP) in adult teeth undergoing primary root canal treatment with the adjunctive use of laser-activated irrigation (LAI) as compared with conventional needle irrigation (CNI) during the first post-operative week. DATA: An electronic search was performed; no language constraints or restriction on the year of publication were applied. SOURCES: Medline, Scopus, Cochrane and PubMed on 04 June 2023 STUDY SELECTION: Randomised clinical trials (RaCTs) that evaluated PEP after LAI of endodontic irrgants were included. Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines were used. PEP was analysed at various time intervals until 1 week after treatment, related to the type of LAI used and the need for analgesia. REULTS: Of the 793 articles identified through the electronic database search, 6 RaCTs were included. Qualitative review was favoured over meta-analysis due to substantial methodological heterogeneity between studies. Five studies were at high risk for bias determined by the Cochrane Risk-of-Bias 2 tool. Diode LAI demonstrated superior efficacy to needle irrigation in reducing pain 6-48 h post-treatment. The impact of LAI by photon-induced photoacoustic streaming (PIPS) was unclear and no difference was observed between PIPS and needle irrigation. However, PIPS mitigated PEP better than manual dynamic activation, sonic and ultrasonic activation. There was no difference in analgesia intake between LAI and needle irrigation groups. CONCLUSIONS: LAI may help reduce PEP in the first 48 h. Methodological standardisation of future RaCTs on LAI would be beneficial in allowing a more accurate review with the possibility of quantitative synthesis. CLINICAL SIGNIFICANCE: This unique synthesis used stringent criteria to reduce confounding factors and provided valuable evidence regarding PEP with different types of LAI. It helps clinicians choose an appropriate LAI technique as compared with CNI and predicts a time frame for reducing PEP.

Comparative evaluation of hand and rotary file systems on dentinal microcrack formation during pulpectomy procedure in primary teeth: an in vitro study.

PURPOSE: Pulpectomy can be used for the management of deep dentinal carious lesions in primary teeth which can be restored. Mechanical preparation of root canals can be performed using hand or NiTi rotary files. However, this may cause dentinal stress and consequently dentinal microcracks. Hence, the aim was comparative evaluation of hand and rotary file systems on dentinal microcrack formation during pulpectomy procedure in primary teeth. METHODS: 60 extracted primary molar teeth were selected comprising of 80 root canals. Simple random sampling was used to divide root canals into four groups (n = 20): Group A-Hedstrom file, Group B-Pro AF Baby Gold rotary, Group C-ProTaper Next rotary, and Group D-unprepared group. Assessment was conducted on presence or absence of microcracks using Chi square test (p < 0.05). RESULTS: The total number of microcracks in Group A: one (5%), Group B: four (20%), Group C: nine (45%) and Group D: zero (0%) which was statistically significant (p = 0.002). At cervical third, the number of microcracks seen with Group A: one (5%), Group B: zero (0%), Group C: five (25%) and Group D: zero (0%) (p = 0.005). At the middle third, the number of microcracks seen in Group A: zero (0%), Group B: four (20%), Group C: four (20%) and Group D: zero (0%) (p = 0.029). CONCLUSION: The study concluded that dentinal microcracks are formed with both hand and rotary file systems in primary teeth. ProTaper Next showed significantly higher number of microcracks, followed by ProAF Baby Gold and H files.