Application of microemulsions for the removal of synthetic resins from paintings on canvas.

Traditional cleaning methods with organic solvents often are not suitable for removal of aged resin so researchers have to find new formulations. In this work, a case study is reported in which new microemulsions were applied on the surface of a painting covered by some aged resin layers used during a previous restoration. Based on the quality of the intervention and the analysis of a sample of the varnish carried out with both MALDI-TOF and ATR-IR spectrometers, it was conjectured that this undesired material could be an acrylic polymer. So it was chosen to use xylene, ethyl acetate and propylene carbonate (XYL and EAPC) microemulsions (O/W oil in water). The first is able to solubilise only acrylic polymers, the second may solve both acrylic and vinyl resins. The first has had the greatest effect allowing complete varnish removal and original artwork restoration.

All-Aqueous Nanoprecipitation: Spontaneous Formation of Hydrogen-Bonded Nanoparticles and Nanocapsules Mediated by Phase Separation of Poly(N-Isopropylacrylamide).

Spontaneous formation of polymer nanoparticles of well-defined, <100 nm sizes with controlled solid/hollow morphology and fluorescent properties is reported. The nanoparticle formation is assisted by temperature-triggered nucleation of an amphiphilic polymer-poly(N-isopropylacrylamide) (PNIPAM)-and mediated by hydrogen bonding of the emerged nuclei with tannic acid (TA). The pH of solution and TA/PNIPAM ratios are explored as parameters that define TA/PNIPAM assembly. Well-defined nanoparticles are formed in a wide range of neutral pH when the TA/PNIPAM ratio exceeds its critical, pH-dependent value. Dynamic light scattering and zeta potential measurements as well as atomic force microscopy and electron energy loss spectroscopy indicate that solid nanoparticles or nanocapsules are formed depending on the solution pH and that enhanced ionization of TA favors hollow morphology. Nanocapsules exhibit label-free fluorescence at neutral pH values and therefore can be useful in imaging applications.

Analysis using size exclusion chromatography of poly(N-isopropyl acrylamide) using methanol as an eluent.

Size Exclusion Chromatography is traditionally carried out in either aqueous or non-polar solvents. A system to present molar mass distributions of polymers using methanol as a mobile phase is presented. This is shown to be a suitable system for determining the molar mass distributions poly(N-isopropylacrylamide)s (PNIPAM); a polymer class that is often difficult to analyze by size exclusion chromatography. DOSY NMR was used to provide intrinsic viscosity data that was used in conjunction with a viscometric detector to provide absolute calibration. Then the utility of the system was shown by providing the absolute molar mass distributions of dispersed highly branched PNIPAM with biologically functional end groups.

Using capillary electrophoresis to characterize polymeric particles.

Capillary electrophoresis (CE) was used for the characterization of a variety of polymeric micron and sub-micron particles based on size, surface functionality, and binding properties. First, a robust capillary zone electrophoresis (CZE) method was developed for the baseline separation and quantitation of commercially available polystyrene particles with various surface modifications (including amino, carboxylate, and sulfate functional groups) and various sizes (0.2, 0.5, 1.0, and 3.0µm). The separation of DNA-templated polyacrylamide particles from untemplated particles (as used for the Ion Torrent Personal Genome Machine) was demonstrated. Finally, using the 29-base thrombin aptamer and thrombin protein as a model system, a study was undertaken to determine dissociation constants for the aptamer and protein in free solution and when the aptamer was conjugated to a particle, with the goal of better understanding how the use of solid substrates, like particles, affects selection and binding processes. Dissociation constants were determined and were found to be approximately 5-fold higher for the aptamer conjugated to a particle relative to that in free solution.

Effect of residual monomer from polyacrylamide on head lettuce grown in peat substrate.

The paper investigates the migration of the acrylamide monomer (AMD) to lettuce chosen as a test plant growing in an organic medium (peat substrate). Polyacrylamide (PAM)-based flocculant added to the growing medium contained no more than 1000 mg kg(-1) of AMD. Plants were grown with varied doses of PAM preparation (0.5-3.0 mg dm(-3) of peat substrate) to compare the results with the control sample. The determination of AMD content, chlorophyll content, weight of the lettuce head, and also analysis of macro- and micro-elements in lyophilised test material was made under the same analytical conditions. The results showed that lettuce plants absorb AMD to the leaves from the peat substrate. The AMD uptake has a negative impact on the growth of lettuce. It reduces the average fresh weight of heads and destabilises the mineral composition of the plant. Therefore, concern related to the transfer risk of the residual AMD from sludge used for organic fertilisation of edible plants still remains a crucial question from a food and consumer safety point of view. To ensure consumer safety, the fate of the AMD following the application of PAM to cropland should be carefully monitored in the whole food chain.

Evaluation of extractables in processed and unprocessed polymer materials used for pharmaceutical applications.

Polymeric materials are often used in pharmaceutical packaging, delivery systems, and manufacturing components. There is continued concern that chemical entities from polymeric components may leach into various dosage forms, particularly those that are comprised of liquids such as parenterals, injectables, ophthalmics, and inhalation products. In some cases, polymeric components are subjected to routine extractables testing as a control measure. To reduce the risk of discovering leachables during stability studies late in the development process, or components that may fail extractables release criteria, it is proposed that extractables testing on polymer resins may be useful as a screening tool. Two studies have been performed to evaluate whether the extractables profile generated from a polymer resin is representative of the extractables profile of components made from that same resin. The ELSIE Consortium pilot program examined polyvinyl chloride and polyethylene, and another study evaluated polypropylene and a copolymer of polycarbonate and acrylonitrile butadiene styrene. The test materials were comprised of polymer resin and processed resin or molded components. Volatile, semi-volatile, and nonvolatile chemical profiles were evaluated after headspace sampling and extraction with solvents of varying polarity and pH. The findings from these studies indicate that there may or may not be differences between extractables profiles obtained from resins and processed forms of the resin depending on the type of material, the compounds of interest, and extraction conditions used. Extractables testing of polymer resins is useful for material screening and in certain situations may replace routine component testing.

Quantitative characterization by asymmetrical flow field-flow fractionation of IgG thermal aggregation with and without polymer protective agents.

Complexes formed between poly(acrylates) and polyclonal immunoglobulin G (IgG) in its native conformation and after heat stress were characterized using asymmetric flow field-flow fractionation (AF4) coupled with on-line UV-Vis spectroscopy and multi-angle light-scattering detection (MALS). Mixtures of IgG and poly(acrylates) of increasing structural complexity, sodium poly(acrylate) (PAA), a sodium poly(acrylate) bearing at random 3 mol % n-octadecyl groups, and a random copolymer of sodium acrylate (35 mol%), N-n-octylacrylamide (25 mol%) and N-isopropylacrylamide (40 mol%), were fractionated in a sodium phosphate buffer (0.02 M, pH 6.8) in the presence, or not, of 0.1 M NaCl. The AF4 protocol developed allowed the fractionation of solutions containing free poly(acrylates), native IgG monomer and dimer, poly(acrylates)/IgG complexes made up of one IgG molecule and a few polymer chains, and/or larger poly(acrylates)/IgG aggregates. The molar mass and recovery of the soluble analytes were obtained for mixed solutions of poly(acrylates) and native IgG and for the same solutions incubated at 65 °C for 10 min. From the combined AF4 results, we concluded that in solutions of low ionic strength, the presence of PAA increased the recovery ratio of IgG after thermal stress because of the formation of electrostatically-driven PAA/IgG complexes, but PAA had no protective effect in the presence of 0.1 M NaCl. Poly(acrylates) bearing hydrophobic groups significantly increased IgG recovery after stress, independently of NaCl concentration, because of the synergistic effect of hydrophobic and electrostatic interactions. The AF4 results corroborate conclusions drawn from a previous study combining four analytical techniques. This study demonstrates that AF4 is an efficient tool for the analysis of protein formulations subjected to stress, an important achievement given the anticipated important role of proteins in near-future human therapies.

Enantiomeric differentiation by synthetic helical polymers.

Recent advances in the synthesis of helical polymers and their applications as chiral materials, in particular chiral stationary phases (CSPs), for high-performance liquid chromatography (HPLC) are reviewed with an emphasis on the key role of the helical conformations with one-handedness for the prominent chiral recognition of enantiomers. The historical background of artificial optically active helical polymers is also briefly described.

Nonionic polymer cross-linked chitosan hydrogel: preparation and bioevaluation.

A straightforward method to prepare nonionic polymer (polyacrylamide, PAM) cross-linked chitosan hydrogel has been developed. The chitosan-polyacrylamide (CS-PAM) hydrogel could be quickly obtained by simply mixing of chitosan and polyacrylamide solutions under very benign condition (room temperature, <30 s). The cytotoxicity and hemocompatibility of the CS-PAM hydrogel were subsequently investigated. Cells retained normal morphology even when the concentration of CS-PAM hydrogel in culture system was as high as 640 µg mL(-1), indicating the CS-PAM hydrogel has minimal cytotoxicity to A549 and HeLa cells. Meanwhile, no hemolysis was observed after incubating the CS-PAM hydrogel with red blood cells for 6 h, further suggesting excellent biocompatibility of the hydrogel. Scanning electron microscopy images illustrated that the CS-PAM hydrogel can absorb red blood cells through the interaction between the protonated amine groups on chitosan and the negative charged residues on red blood cell membranes. Given its low cost, simple preparation, and excellent biocompatibility, this CS-PAM hydrogel might be a potential biomaterial for future healthcare and biomedical applications.

Antiscalant removal in accelerated desupersaturation of RO concentrate via chemically-enhanced seeded precipitation (CESP).

An experimental study was carried out to demonstrate and quantify the feasibility of antiscalant (AS) removal from brackish water RO concentrate of high gypsum scaling propensity via lime treatment prior to seeded gypsum precipitation. Based on studies with model solutions, it was shown that sufficient AS removal (up to ∼90%) from RO concentrate is feasible via a lime treatment step (at a dose significantly lower than that required for conventional lime softening) to enable effective subsequent seeded gypsum precipitation. This two-step chemically-enhanced seeded precipitation (CESP) treatment of primary RO concentrate is suitable as an intermediate concentrate demineralization (ICD) stage for high recovery desalting employing secondary RO desalination. Analysis of gypsum precipitation and lime treatment kinetic data suggests that, after adequate CaCO(3) precipitation has been induced for effective AS scavenging, CaSO(4) desupersaturation can be achieved via seeded gypsum precipitation without retardation due to seed poisoning by AS. Also, the lime dose required to prevent seed poisoning during subsequent gypsum desupersaturation via seeded gypsum precipitation can be adequately assessed with a precipitation kinetics model that considers AS seed poisoning based on a Langmuir adsorption isotherm. The degree of AS removal after lime treatment increased linearly with the logarithm of the single lime dose additions. Staged lime dosing (i.e., multiple lime additions), however, removed a higher degree of AS relative to an equivalent single lime dose addition since a higher driving force for CaCO(3) precipitation could be maintained over the course of the lime treatment period.

Hemocompatible poly(NIPAm-MBA-AMPS) colloidal nanoparticles as carriers of anti-inflammatory cell penetrating peptides.

Anionic copolymer systems containing sulfated monomers have great potential for delivery of cationic therapeutics, but N-isopropylacrylamide (NIPAm) 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) copolymer nanoparticles have seen limited characterization to date with regard to physical properties relevant to loading and release of therapeutics. Characterization of polymeric nanoparticles incorporating AMPS showed an increased size and decreased thermodynamic swelling ratios of AMPS containing particles as compared to NIPAm nanoparticles lacking AMPS. Particles with increasing AMPS addition showed an increased propensity for uniformity, intraparticle colloidal stability, and drug loading capacity. Peptide encapsulated in particles was shielded from peptide degradation in serum. Particles were shown not impede blood coagulation or to cause hemolysis. This study has demonstrated that AMPS incorporation into traditional NIPAm nanoparticles presents a tunable parameter for changing particle LCST, size, swelling ratio, ζ potential, and cationic peptide loading potential. This one-pot synthesis results in a thermosensitive anionic nanoparticle system that is a potentially useful platform to deliver cationic cell penetrating peptides.

Isotherm and kinetic behavior of adsorption of anion polyacrylamide (APAM) from aqueous solution using two kinds of PVDF UF membranes.

To determine the isotherm parameters and kinetic parameters of adsorption of anion polyacrylamide (APAM) from aqueous solution on PVDF ultrafiltration membrane (PM) and modified PVDF ultrafiltration membrane (MPM) is important in understanding the adsorption mechanism of ultrafiltration processes. Effect of variables including adsorption time, initial solution concentration, and temperature were investigated. The Redlich-Peterson equation of the five different isotherm models we chose was the most fitted model, and the R(2) was 0.9487, 0.9765 for PM and MPM, respectively; while, the pseudo-first-order model was the best choice among all the four kinetic models to describe the adsorption behavior of APAM onto membranes, suggesting that the adsorption mechanism was a chemical and physical combined adsorption on heterogeneous surface. The thermodynamic parameters were also calculated from the temperature dependence (Δ(r)G(m)(θ), Δ(r)H(m)(θ), Δ(r)S(m)(θ)), which showed that the process of adsorption is not spontaneous but endothermic process and high temperature favors the adsorption.

Methods for purifying and detoxifying sodium dodecyl sulfate-stabilized polyacrylate nanoparticles.

Recent research in our laboratory has centered on studies of polyacrylate and polyacrylamide nanoparticle emulsions for use in antibiotic delivery. Our goal is to develop these nanoparticle emulsions for treatment of life-threatening bacterial infections such as those caused by methicillin-resistant Staphylococcus aureus. For this intended application it is necessary to ensure that the biological activity of the emulsion is due only to the drug attached to the polymeric chain and not to any extraneous components. To investigate this we evaluated cytotoxicity and microbiological activity of the nanoparticle emulsions before and after purification by centrifugation, dialysis, and gel filtration. Depending on the amount of surfactant used, all or most of the microbial and cellular toxicity can be removed by a simple purification procedure.

Preparation and properties of thermoresponsive bioconjugates of trypsin.

Covalent attachment of enzymes and other proteins to the smart polymer, poly(N-isopropylacrylamide) [poly (NIPAAm)], has been widely used as a method for the preparation of thermosensitive protein conjugates. In the present study, reversible soluble-insoluble polymer-enzyme conjugates were prepared by conjugating a copolymer of NIPAAm with 5-mol % of 6-acrylaminohexanoic acid to trypsin by the carbodiimide-NHS (N-hydroxysuccinimide) coupling method. Four bioconjugates with different units of enzyme coupled to the matrix were prepared. Increased enzymatic activity in terms of high effectiveness factor (in the range of 3-5) was found in the conjugates. Kinetic parameters for the immobilized and free enzyme were determined. The Vmax/Km value of the enzyme significantly increased on immobilization by the factors in the range of 12-28. The immobilized enzyme also showed stability to autolysis at 50 degrees C.

Report: recycling of flame-retarded plastics from waste electric and electronic equipment (WEEE).

Shredder residues produced in plants processing waste electric and electronic equipment are excluded from material recycling due to a variety of polymeric materials and the presence of brominated flame retardants (BFR), which might contain banned polybrominated diphenyl ethers or toxic polybrominated dioxins and furans (PBDD/F). Herein we present a technological approach to transfer a significant portion of the shredder residue into recycled polymers. The technological approach consists of a density-based enrichment of styrenics, which are subjected to a solvolysis process (CreaSolv process) in a second stage. This stage allows the elimination of non-target polymers and extraction of BFR and PBDD/F. Pilot processing of 11.5 and 50 kg shredder residues indicated a material yield of about 50% in the density stage and 70-80% in the CreaSolv process, and an effective removal of BFR additives. The recycled products were proved to comply with threshold values defined by the European directive on the restriction of hazardous substances (RoHS) and the German Chemikalienverbotsverordnung. Mechanical material properties exhibited high tensile and flexural modules as well as slight impact strength, which qualify the products for applications in new electronic equipment.

Large-scale preparation and purification of polyacrylamide-free RNA oligonucleotides.

We present a fast and simple protocol for large-scale preparation and purification of RNA oligonucleotides. RNA oligonucleotides are prepared by in vitro transcription with T7 RNA polymerase from linearized plasmid DNA templates constructed by PCR. In place of denaturing polyacrylamide gel electrophoresis (PAGE), size-exclusion chromatography is employed to purify the RNA oligonucleotide from the transcription mixture yielding >99% pure RNA product. In contrast to PAGE-based purification, the gel filtration method does not require denaturation of the RNA oligonucleotide, which is desirable for larger RNAs, and the product is free of low-molecular-weight acrylamide contaminants, which greatly benefits NMR, crystallographic, and other biophysical studies of large RNAs and RNA-protein complexes.

[The tissue reaction to acrylic plastics modified by supercritical extraction with carbon dioxide]. / Tkanevaia reaktsiia na akrilovye plastmassy, modifitsirovannye sverkhkriticheskoi ékstraktsiei dvuokis'iu ugleroda.

The process of extraction of admixtures from acryl plastic widely used in dentistry by means of supercritical carbon dioxide (sc-CO2) was studied and effects of extraction conditions on biocompatibility and toxicity of resultant materials assessed, sc-CO2 effectively purified the specimens from toxic compounds (monomers and low-molecular oligomers, methylmethacrylate, dichloroethane) and notably improved the biocompatability of polymer implants. Tissue reaction to ethacryl and protacryl depends on the degree of implant polymerization and duration of extraction of toxic substances from polymer.

Using light scattering to locate less than a microgram of protein per band in polyacrylamide tube gels after isoelectric focusing.

After separation by isoelectric focusing (IEF) or non-equilibrium pH gradient electrophoresis (NEPHGE) in 9.2 M urea polyacrylamide tube gels, proteins with Mr > 20,000 can be precipitated by shaking the gels in 25% methanol. When a fiber-optic illuminator is placed in contact with the end of the gel, the cylindrical gel transmits light by internal reflection. In regions of the gel where protein is precipitated, this light is scattered, making it visible when the gel is viewed in a darkened room against a black background. The sensitivity of the method is moderate: less than 1 microgram protein per band (in a 3-mm diameter gel) can be detected. Because the protein in the bands precipitates rapidly (30 min), the solution used (25% methanol) is fairly benign to proteins, and the apparatus is not expensive, this technique should be useful in several situations including electrophoretic purification schemes. This method is especially useful for evaluating the quality of an IEF or NEPHGE tube gel before using it for the second dimension of a two-dimensional gel.

Allergic contact dermatitis to artificial fingernails prepared from UV light-cured acrylates.

BACKGROUND: Contact dermatitis from artificial nails made from self-curing acrylic resins is occasionally reported. Recently, UV light-cured products introducing new acrylics have become available. OBJECTIVE: Our purpose was to identify relevant allergens in commercial light-curing products by patch tests and to evaluate the efficacy of "hypoallergenic" products by inclusion into the test series. METHODS: Patients wearing photobonded acrylic nails who had perionychial and subonychial eczema were patch tested with an acrylate battery and "hypoallergenic" commercial products. RESULTS: Triethyleneglycol dimethacrylate, hydroxyfunctional methacrylates, and (meth)-acrylated urethanes proved to be relevant allergens in photobonded nail preparations. Methacrylated epoxy resin sensitization was not observed. All "hypoallergenic" products provoked positive reactions. CONCLUSION: The omission of irritant methacrylic acid in UV-curable products does not reduce the high sensitizing potential of new acrylates. In contrast to the manufacturers' declarations, all "hypoallergenic" products continue to include acrylate functional monomers and therefore continue to cause allergic sensitization.

'Laterally aggregated' polyacrylamide gels for electrophoresis.

A new method is described for producing highly porous polyacrylamide matrices: polymerization in presence of a preformed hydrophilic polymer. If a standard mixture of monomers (e.g., 5%T, 4%C) is polymerized in presence of, e.g., polyethylene glycol (PEG) 10 kDa, lateral chain aggregation occurs, with formation of large pore sizes. In PEG 10 kDa, the transition from a small- to a large-pore gel is clearly apparent at 0.5% PEG addition and reaches a plateau already at 2.5% PEG. Even with shorter PEG fragments (6.2 and 1 kDa) this transition occurs, but with progressively larger amounts of PEG in solution (up to 25% for the 1 kDa species). Other polymers such as hydroxymethyl cellulose (1000 kDa) and polyvinyl-pyrrolidone (360 kDa and 25 kDa) are also able to elicit this phenomenon. It appears that lateral chain aggregation (before the cross-linking event) is induced via intra-chain hydrogen bonding, since urea and temperature strongly inhibit it, whereas tetramethylurea (an agent quenching hydrophobic interactions) does not hamper it. By scanning electron microscope, it is found that the maximum pore size obtained in a 5%T, 4%C gel in presence of 2.5% PEG 10 kDA is of the order of 0.5 micron, whereas the same 5%T, 4%C control gel would have an average pore diameter of 5 nm. Thus, an increment of pore size of about 2 orders of magnitude is obtained: in these new matrices, a 21000 bp DNA fragment exhibits a much greater migration than in a control gel in which the sample is entrapped at the application site.