Multiobjective Optimization of Fabrication Parameters of Jute Fiber/Polyester Composites with Egg Shell Powder and Nanoclay Filler.

In the present study, a model is presented to optimize the fabrication parameters of natural fiber reinforced polyester matrix composites with dual fillers. In particular, jute fiber mat was chosen as reinforcement and eggshell powder (ESP) and montmorillonite nanoclay (NC) were selected as fillers. The weight per square meter (GSM) of the fiber, the weight percentage of ESP and NC have been chosen as independent variables and the influence of these variables on tensile, flexural and impact strength of the composite has been inspected. The permutations of the different combinations of factors are intended to accomplish higher interfacial strength with the lowest possible number of tested specimens. The experiments were designed by the Taguchi strategy and a novel multi-objective optimization technique named COPRAS (COmplex PRoportional ASsessment of alternatives) was used to determine the optimal parameter combinations. Affirmation tests were performed with the optimal parameter settings and the mechanical properties were evaluated and compared. Experimental results show that fiber GSM and eggshell powder content are significant variables that improve mechanical strength, while the nanoclay appears less important.

Original and Repair Bulk Fracture Resistance of Particle Filler and Short Fiber-Reinforced Composites.

OBJECTIVE: This study aimed to evaluate the original (OR) and repair (RR) fracture resistance of a semi-interpenetrating polymer network (semi-IPN)-based short fiber-reinforced composite compared to dimethacrylate-based composite materials by means of the V-notch test. METHODS AND MATERIALS: Circular specimens (5×2 mm) with a centrally machined 90° V-shaped notch were prepared. Four bulk fill (Filtek Bulk Fill, Venus Bulk Fill, TetricEvo Ceram Bulk Fill, SDR), three microfilled hybrid (GC-Anterior, GC-Posterior, Z250), one nanofilled (SupremeXTE), and two short fiber-reinforced (Alert, everX Posterior) composites were selected. EverX Posterior was the semi-IPN material. Specimens (n=12/group) were either dry or water stored for 7 and 30 days, respectively, at 37°C and then loaded in two-point load until fracture. One-half of each tested specimen was used for the repair procedure. Repairing surfaces were diamond-bur ground, etched, and treated with silane containing universal adhesive (Scotchbond Universal) before repair. RESULTS: Three-way analysis of variance revealed a significant statistical difference between the groups ( p<0.05). The fracture resistance of dry-stored groups was greater than that of water-stored groups. The highest OR was observed for dry-stored Alert (23.4 N/mm), which significantly deteriorated in water (17.4 N/mm) ( p<0.05). The highest RR was observed for everX Posterior (20.0 N/mm), which did not deteriorate in water significantly (19.0 N/mm) ( p>0.05). The everX Posterior preserved the specimens' integrity at the final fracture load (ductile fracture), whereas all other materials fractured into two halves at the interface (adhesive failure). CONCLUSIONS: The only material that provided enhanced repair strength that was close to the original cohesive strength of the material was everX Posterior. The endurance of repaired restorations can be improved by using semi-IPN-based filling material.

Dynamic and Static Flexural Appraisal of Resin-based Composites: Comparison of the ISO and Mini-flexural Tests.

The objective of this study was to determine the influence of specimen dimension and conditioning medium on the dynamic and static flexural properties of resin-based composites (RBCs). One conventional (Filtek Z350) and two bulk-fill RBCs (Filtek Bulk-fill and Beautifil-Bulk Restorative) were evaluated. Bar-shaped specimens with dimensions 25 × 2 × 2 mm (ISO flexural [IFT]) or 12 × 2 × 2 mm (mini-flexural [MFT]) were fabricated using customized stainless-steel molds, finished, measured, randomly divided into two groups, and conditioned in air or artificial saliva (SAGF) for seven days at 37°C. The specimens (n=10) were then subjected to dynamic and static three-point flexural testing. Data for storage modulus, loss modulus, loss tangent, flexural strength, and modulus were computed and subjected to t-test, analysis of variance/Tukey test, and Pearson correlation at a significance level of α = 0.05. For both IFT and MFT, significant differences in dynamic and static flexural properties were more prevalent between materials after storage in saliva. For both conditioning mediums, the strongest correlation between IFT and MFT was observed for flexural strength. While significant positive correlations were observed for all flexural properties with saliva, no significant correlations were detected for loss tangent and flexural modulus with air. For both IFT and MFT, storage in saliva appeared to be more discriminative than storage in air. As moderate to strong positive relationships exist between IFT and MFT for dynamic and static flexural properties, the mini-flexural test holds promise as a replacement for the ISO 4049 in view of its clinical relevance and greater efficiency.

Optimizing quality and safety of dental materials.

This paper discusses aspects of quality and safety improvement of the most commonly used dental restorative materials, the resin-based composites. From a patient's perspective, long-lasting resin-based restorations without complications are important. Recurrent caries and fracture are the most common causes for restoration failures. Proper handling and curing of the composites improve the mechanical properties of the restorations and increase safety by reducing exposure to residual methacrylate monomers. A number of compounds have been introduced in restorative materials to reduce the risk of recurrent caries, even though a real breakthrough has not yet been achieved. It is concluded that simple measures may improve the quality and safety of resin-based composite restorations.

OCT for early quality evaluation of tooth-composite bond in clinical trials.

OBJECTIVES: To evaluate early quality of composite restorations with a universal adhesive in different application modes clinically and with optical coherence tomography (OCT). METHODS: 22 patients with four non-carious cervical lesions each received composite restorations (Filtek Supreme™ XTE, 3 M). The universal adhesive Scotchbond Universal™(SBU, 3 M) was applied with three etching protocols: self-etch (SE), selective-enamel-etch (SEE) and etch-and-rinse (ER). The etch-and-rinse adhesive OptiBond™ FL (OFL, Kerr) served as a control. Restorations were imaged by OCT (Thorlabs) directly after application (t0). After 14 days (t1) and 6 month (t2) OCT imaging (interfacial adhesive defects) was repeated combined with clinical assessment (FDI criteria). Groups were compared by Friedman-/Wilcoxon- and McNemar-Test. RESULTS: No differences were seen clinically between groups (pi ≥ 0.500). OCT assessment revealed more adhesive defects at the enamel interface with SBU/SE at t0-t2 compared to all groups (pi ≤ 0.016). OFL showed more defects than SBU/ER (t1: p = 0.01; t2: p = 0.083). At dentin/cementum interface OFL exhibited more adhesive defects than SBU with all conditioning modes (t0, t1, pi ≤ 0.003) and at t2 to SBU/SE and SBU/ER (p < 0.001). Since t1 defects with SBU were detected more frequently in the SE and SEE modes compared to ER (pi ≤ 0.037). In contrast to SBU defects increased with OFL up to t2 (pi ≤ 0.007). CONCLUSIONS: In contrast to clinical evaluation, OCT revealed subtle adhesive defects directly after application that might interfere with clinical success. It was demonstrated that ER does not decrease initial adhesion of SBU to dentin.

Effects of core-to-dentin thickness ratio on the biaxial flexural strength, reliability, and fracture mode of bilayered materials of zirconia core (Y-TZP) and veneer indirect composite resins.

STATEMENT OF PROBLEM: Indirect composite resins (ICR) are promising alternatives as veneering materials for zirconia frameworks. The effects of core-to-dentin thickness ratio (C/Dtr) on the mechanical property of bilayered veneer ICR/yttria-tetragonal zirconia polycrystalline (Y-TZP) core disks have not been previously studied. PURPOSE: The purpose of this in vitro study was to assess the effects of C/Dtr on the biaxial flexural strength, reliability, and fracture mode of bilayered veneer ICR/ Y-TZP core disks. MATERIAL AND METHODS: A total of 180 bilayered 0.6-mm-thick composite resin disks in core material and C/Dtr of 2:1, 1:1, and 1:2 were tested with either core material placed up or placed down for piston-on-3-ball biaxial flexural strength. The mean biaxial flexural strength, Weibull modulus, and fracture mode were measured to evaluate the variation trend of the biaxial flexural strength, reliability, and fracture mode of the bilayered disks with various C/Dtr. One-way analysis of variance (ANOVA) and chi-square tests were used to evaluate the variation tendency of fracture mode with the C/Dtr or material placed down during testing (α=.05). Light microscopy was used to identify the fracture mode. RESULTS: The mean biaxial flexural strength and reliability improved with the increase in C/Dtr when specimens were tested with the core material either up and down, and depended on the materials that were placed down during testing. The rates of delamination, Hertzian cone cracks, subcritical radial cracks, and number of fracture fragments partially depended on the C/Dtr and the materials that were placed down during testing. CONCLUSION: The biaxial flexural strength, reliability, and fracture mode in bilayered structures of Y-TZP core and veneer ICR depend on both the C/Dtr and the material that was placed down during testing.

Clinical performance of aesthetic restorative materials in primary teeth according to the FDI criteria.

AIM: The purpose of this study is to evaluate the clinical performance of three different restorative materials in primary teeth according to the FDI criteria. MATERIALS AND METHODS: Resin-modified glass ionomer cement, compomer and composite resin restorations (n=93) were made in 31 patients. The restorations were clinically evaluated at baseline, 6th, 12th and 18th month with the FDI criteria. RESULTS: The cumulative survival rate after 18 months was found to be 90.3% for resin modified glass ionomer cement restorations, 100% for compomer restorations and 80.6% for composite resin restorations. Statistically significant increase in surface roughness, colour mismatch, anatomic form loss and marginal deterioration were detected in resin- modified glass ionomer group (p<0.05). The most frequent reason for restoration failure in composite resin group was restoration fractures. CONCLUSIONS: The resin-modified glass ionomer restorations necessitates close follow-up because of the risk of increase in surface roughness, changes in colour and loss in anatomic form and marginal adaptation. The clinical performance of compomer restorations is superior to resin-modified glass ionomer and composite resin restorations in primary teeth.

Fechamento de diastema com resina composta direta: relato de caso clínico / Diastema closure with direct composite restorations: a case report

Com a evolução dos materiais restauradores adesivos diretos e das técnicas restauradoras minimamente invasivas, é possível realizar o fechamento de diastemas inter incisivos superiores de maneira efetiva e estética em uma única sessão. O presente trabalho consiste em um relato de caso clínico que aborda o clareamento dental e o fechamento de diastema entre os dentes 11 e 21 de um paciente jovem. Previamente ao procedimento restaurador foi realizado clareamento de consultório em todos os dentes com peróxido de hidrogênio 35%. Então, o planejamento restaurador foi auxiliado por modelos de estudo associado ao enceramento diagnóstico.A técnica restauradora de eleição foi a resina composta direta com o auxílio de uma matriz/guia de silicona para a confecção das faces palatinas das restaurações. Após o acabamento e polimento, obteve-se a reanatomização dos incisivos centrais com a eliminação do diastema. O tratamento realizado baseado no clareamento dental seguido por restaurações diretas de resina composta foi eficaz na solução estética do sorriso, atingindo a expectativa do paciente e dentro dos princípios de máxima preservação dos tecidos dentais.

After the evolution of restorative adhesive materials and minimal invasive restorations, it ispossible to close a maxilar interincisal diastema in an effective and aesthetical way, performingit in only one session. This clinical case report approaches a teeth bleaching and diastema closurewith composites between teeth 11 and 21, of a young male patient. The elective restorative technique was direct composite restoration with a silicon putty matrix to make the shape of thelingual surfaces of the restorations. Before the restoration procedure, it was performed “in office”bleaching technique, in addition to the case planning with the assistance of a wax-up. The tooth whitening therapy followed by direct composite restorations was effective, contributing to clinical success, esthetic and patient´s satisfaction.

Relation between conversion degree and cytotoxicity of a flowable bulk-fill and three conventional flowable resin-composites.

OBJECTIVE: The aim of this study is to evaluate if the cytotoxic effects of the Surefil SDR flow, bulk fill flowable composite resin and three conventional flowable materials (Venus Diamond Flow, Filtex Supreme XTE Flowable and Enamel plus HRi Flow) correlated with the conversion degree (DC); hardness and depth of cure are also assessed. MATERIALS AND METHODS: Disks of each materials--cured using LED lamp--are utilized to evaluate DC (by FT-IR technique), amount of leached monomers (by HPLC technique), hardness (by Vickers hardness tester) and cytotoxicity (by MTT test). RESULTS: All tested materials show light cytotoxic effects, independently from DC values. Both the latter parameter and the hardness, in fact, change in function of thickness and type of material. HPLC results show that the monomers amount leached from each specimen is influenced by thickness but it is always very low which justifies the absence of any cytotoxic effect. CONCLUSIONS: Our findings suggest that there are not statistically significant differences in cytotoxicity in all experimental conditions, notwithstanding the differences in hardness and in degree of conversion.

A new methodology for fluorescence analysis of composite resins used in anterior direct restorations.

The aim of this study was to use a new methodology to evaluate the fluorescence of composite resins for direct restorations. Microhybrid (group 1, Amelogen; group 2, Opallis; group 3, Filtek Z250) and nanohybrid (group 4, Filtek Z350 XT; group 5, Brilliant NG; group 6, Evolu-X) composite resins were analyzed in this study. A prefabricated matrix was used to prepare 60 specimens of 7.0 × 3.0 mm (n = 10 per group); the composite resin discs were prepared in 2 increments (1.5 mm each) and photocured for 20 seconds. To establish a control group of natural teeth, 10 maxillary central incisor crowns were horizontally sectioned to create 10 discs of dentin and enamel tissues with the same dimensions as the composite resin specimens. The specimens were placed in a box with ultraviolet light, and photographs were taken. Aperture 3.0 software was used to quantify the central portion of the image of each specimen in shades of red (R), green (G), and blue (B) of the RGB color space. The brighter the B shade in the evaluated area of the image, the greater the fluorescence shown by the specimen. One-way analysis of variance revealed significant differences between the groups. The fluorescence achieved in group 1 was statistically similar to that of the control group and significantly different from those of the other groups (Bonferroni test). Groups 3 and 4 had the lowest fluorescence values, which were significantly different from those of the other groups. According to the results of this study, neither the size nor the amount of inorganic particles in the evaluated composite resin materials predicts if the material will exhibit good fluorescence.

Depth of cure of bulk-fill flowable composite resins.

In recent years, manufacturers have introduced flowable composite resins that reportedly can be placed in increments of 4 mm or greater. The purpose of this study was to evaluate the depth of cure of bulk-fill flowable composite resins (SureFil SDR Flow, Grandio Flow, and Venus Bulk Fill) and a conventional flowable composite resin (Revolution Formula 2). Depth of cure was measured in terms of bottom-maximum Knoop hardness number (KHN) ratios and the International Organization for Standardization (ISO) 4049 scrape technique. Shades A2 and A3 of SureFil SDR Flow, Grandio Flow, and Revolution Formula 2 were tested. Venus Bulk Fill was tested in its only available shade (universal). Specimens in thicknesses of 2, 3, 4, 5, and 6 mm were polymerized for 20 or 40 seconds, and a hardness tester was used to determine the hardness ratios for each shade at each thickness. For the scraping technique, after specimens were exposed to the curing light, unpolymerized composite resin was removed with a plastic instrument, the polymerized composite was measured, and the length was divided by 2 per ISO guidelines. According to the KHN ratios and the scrape test, Venus Bulk Fill predictably exceeded the manufacturer's claim of a 4-mm depth of cure at both 20 and 40 seconds of curing time. The overall results for depth of cure showed that Venus Bulk Fill ≥ SureFil SDR Flow ≥ Grandio Flow ≥ Revolution Formula 2.

Dental students' ability to assess their performance in a preclinical restorative course: comparison of students' and faculty members' assessments.

Dental education consists of both theoretical and practical learning for students to develop competence in treating patients clinically. When dental students encounter practical courses in their first year as a new educational experience, they must also learn to evaluate themselves. Self-evaluation is an essential skill to learn for dental professionals to keep increasing their competence over the course of their careers. The aim of this study was to compare the assessment scores of second- and third-year dental students and the faculty in two consecutive preclinical practical exams in restorative dentistry courses in a dental school in Turkey. Faculty- and student-assigned scores were calculated from two consecutive preclinical examinations on tooth restorations performed on both artificial casts and phantom patients. The students were formally instructed on grading procedures for tooth preparations, base and restoration placement, and polishing criteria. After each step, each item was assessed by faculty members, the student, and another student. The results indicated that the initial differences between second-year students' assessments of their own preclinical practical ability and that of the faculty decreased among the third-year students. Self-evaluation scores did not indicate whether the third-year students tended to over- or underestimate the quality of their own work. However, the second-year students not only overestimated themselves but thought they were above average. The results point to the need to develop students' self-insight with more exercises and practical training.

Evaluation of the bond strengths of 3 endodontic cements via push-out test.

In this study, the push-out method was used to evaluate the bond strengths of 3 types of endodontic cements according to their composite base: methacrylate, epoxy resin, and an experimental copaiba oil resin. The study hypothesis was that the methacrylate-based and experimental cements would have bond strengths equal to or greater than that of the epoxy resin-based cement. Thirty bovine tooth roots, 18 mm long, were divided into 3 groups (n = 10) based on the chosen cement treatment. After treatment, the specimens were sectioned and submitted to a push-out test. Results showed that there was no statistically significant difference (P < 0.05) between the cements used or between the middle and apical thirds of the roots. It could be concluded that the tested cements had satisfactory and similar bond strengths to dentin.

Low-shrinkage composites: an in vitro evaluation of sealing ability after occlusal loading.

The objective of this in vitro study was to compare the microleakage of a flowable low-shrinkage-stress resin composite--in a Class II fatigue-loading design when used as a 4 mm dentin replacement--to a conventionally layered silorane-based resin composite. Eighty standardized 4 mm deep cavities, divided into 4 subgroups, were restored with the 2 tested materials. Half of the restorations were submitted to mechanical loading, and all of the restorations were prepared for microleakage evaluation. The evaluation of the marginal adaptation to dentin was performed with scanning electron microscopy. The results showed that both silorane-based composite groups had higher rates of microleakage in comparison to the low-shrinkage-stress resin composite groups.

Evaluation of marginal integrity of four bulk-fill dental composite materials: in vitro study.

OBJECTIVE: The aim of the study was to compare under in vitro conditions marginal sealing of 4 different bulk-fill materials composite restorations of class II. METHODS: Comparative evaluation concerned 4 composites of a bulk-fill type: SonicFill, Tetric EvoCeram Bulk Fill, Filtek Bulk Fill, and SDR. The study used 30 third molars without caries. In each tooth 4 cavities of class II were prepared. The prepared tooth samples were placed in a 1% methylene blue solution for 24 h, and after that in each restoration the depth of dye penetration along the side walls was evaluated. RESULTS: The highest rating (score 0, no dye penetration) was achieved by 93.33% of the restorations made of the SDR material, 90% of restorations of SonicFill system, 86.66% of restorations of the composite Filtek Bulk Fill, and 73.33% of restorations of the Tetric EvoCeram Bulk Fill. CONCLUSION: The performed study showed that bulk-fill flowable or sonic-activated flowable composite restorations have better marginal sealing (lack of discoloration) in comparison with bulk-fill paste-like composite.

Fracture of fiber-reinforced composites analyzed via acoustic emission.

This study investigated the fracture resistance of composite resins using a three-point bending test and acoustic emission (AE) analysis. Three groups of specimens (n=15) were prepared: non-reinforced BelleGlass HP composite (NRC), unidirectional (UFRC) and multidirectional (MFRC) fiber-reinforced groups which respectively incorporated unidirectional Stick and multidirectional StickNet fibers. Specimens were loaded to failure in a universal testing machine while an AE system was used to detect audible signals. Initial fracture strengths and AE amplitudes were significantly lower than those at final fracture in all groups (p<0.05). Initial fracture strength of UFRC (170.0 MPa) was significantly higher than MFRC (124.6 MPa) and NRC (87.9 MPa). Final fracture strength of UFRC (198.1 MPa) was also significantly higher than MFRC (151.0 MPa) and NRC (109.2 MPa). Initial and final fracture strengths were significantly correlated (r=0.971). It was concluded that fiber reinforcement improved the fracture resistance of composite resin materials and the monitoring of acoustic signals revealed significant information regarding the fracture process.

A study of primary teeth restored by intracoronal restorations in children participating in an undergraduate teaching programme at Cork University Dental School and Hospital, Ireland.

AIM: To study the outcomes for restored primary molar teeth; to examine outcomes in relation to tooth type involved, intracoronal restoration complexity and to the material used. DESIGN: Retrospective study of primary molar teeth restored by intracoronal restorations. A series of restored primary molar teeth for children aged 6-12 years was studied. The principal outcome measure was failure of initial restoration (re-restoration or extraction). Three hundred patient records were studied to include three equal groups of primary molar teeth restored with amalgam, composite or glass ionomer, respectively. Restorative materials, the restoration type, simple (single surface) or complex (multi-surface) restoration, and tooth notation were recorded. Subsequent interventions were examined. Data were coded and entered into a Microsoft Excel database and analysis undertaken using SPSS v.18. Statistical differences were tested using the Chi square test of statistical significance. RESULTS: Of the 300 teeth studied, 61 restoration failures were recorded with 11 of those extracted. No significant differences were found between outcomes for upper first, upper second, lower first or lower second primary molars. Outcomes for simple primary teeth restored by intracoronal restorations were significantly better than those for complex intracoronal restorations (P = 0.042). Teeth originally restored with amalgam accounted for 19.7% of the 61 failures, composite for 29.5%, while teeth restored with glass ionomer represented 50.8% of all restoration failures. The differences were significant (P = 0.012). CONCLUSIONS: The majority (79.7%) of the 300 restored primary teeth studied were successful, and 3.7% teeth were extracted. Restorations involving more than one surface had almost twice the failure rate of single surface restorations. The difference was significant. Significant differences in failure rates for the three dental materials studied were recorded. Amalgam had the lowest failure rate while the failure rate with glass ionomer was the highest.

Localized and generalized simulated wear of resin composites.

A laboratory study was conducted to examine the wear of resin composite materials using both a localized and generalized wear simulation model. Twenty specimens each of seven resin composites (Esthet•X HD [HD], Filtek Supreme Ultra [SU], Herculite Ultra [HU], SonicFill [SF], Tetric EvoCeram Bulk Fill [TB], Venus Diamond [VD], and Z100 Restorative [Z]) were subjected to a wear challenge of 400,000 cycles for both localized and generalized wear in a Leinfelder-Suzuki wear simulator (Alabama machine). The materials were placed in custom cylinder-shaped stainless steel fixtures. A stainless steel ball bearing (r=2.387 mm) was used as the antagonist for localized wear, and a stainless steel, cylindrical antagonist with a flat tip was used for generalized wear. A water slurry of polymethylmethacrylate (PMMA) beads was used as the abrasive media. A noncontact profilometer (Proscan 2100) with Proscan software was used to digitize the surface contours of the pretest and posttest specimens. AnSur 3D software was used for wear assessment. For localized testing, maximum facet depth (µm) and volume loss (mm(3)) were used to compare the materials. The mean depth of the facet surface (µm) and volume loss (mm(3)) were used for comparison of the generalized wear specimens. A one-way analysis of variance (ANOVA) and Tukey post hoc test were used for data analysis of volume loss for both localized and generalized wear, maximum facet depth for localized wear, and mean depth of the facet for generalized wear. The results for localized wear simulation were as follows [mean (standard deviation)]: maximum facet depth (µm)--Z, 59.5 (14.7); HU, 99.3 (16.3); SU, 102.8 (13.8); HD, 110.2 (13.3); VD, 114.0 (10.3); TB, 125.5 (12.1); SF, 195.9 (16.9); volume loss (mm(3))--Z, 0.013 (0.002); SU, 0.026 (0.006); HU, 0.043 (0.008); VD, 0.057 (0.009); HD, 0.058 (0.014); TB, 0.061 (0.010); SF, 0.135 (0.024). Generalized wear simulation results were as follows: mean depth of facet (µm)--Z, 9.3 (3.4); SU, 12.8 (3.1); HU, 15.6 (3.2); TB, 19.2 (4.8); HD, 26.8 (6.5); VD, 29.1 (5.5); SF, 35.6 (8.4); volume loss (mm(3))--Z, 0.132 (0.049); SU, 0.0179 (0.042); HU, 0.224 (0.044); TB, 0.274 (0.065); HD, 0.386 (0.101); VD, 0.417 (0.076); SF, 0.505 (0.105). The ANOVA showed a significant difference among materials (p<0.001) for facet depth and volume loss for both localized and generalized wear. The post hoc test revealed differences (p<0.05) in localized and generalized wear values among the seven resin composites examined in this study. The findings provide valuable information regarding the relative wear characteristics of the materials in this study.

[Evaluation of the quality of proximal restorations with plastic materials: radiographic study]. / Evaluation de la qualité des restaurations proximales aux matériaux plastiques. Etude radiographique.

AIM: To assess the quality of proximal coronary restorations and bring out the factors influencing this quality. MATERIAL AND METHOD: A transversal study on 160 radiographs of proximal coronary restorations was conducted at the University Center of Dental Consultation and Treatment of Rabat. Restorations were evaluated according to the modified USPHS criteria. Four variables were studied: restoration material, treated tooth, cavity type and location of treatment in order to identify the influencing factors. RESULTS: Forty five per cent of the evaluated proximal coronary restorations required replacement. The main cause of failure was recurrent caries in 36% of cases, followed by the absence of the contact point (24.4%), unacceptable proximal coronary outline (13.8%), and finally dentin exposure (6.9%). Thus, it turned out that there is a difficulty to restore correctly posterior proximal cavities especially using amalgam and a high rate of recurrent caries at both the anterior and posterior teeth. CONCLUSION: Both a clinical and a radiographic evaluation after each proximal restoration would be recommended to reduce failure.

Research on the mechanical properties of a glass fiber reinforced polymer-steel combined truss structure.

An assembled plane truss structure used for vehicle loading is designed and manufactured. In the truss, the glass fiber reinforced polymer (GFRP) tube and the steel joint are connected by a new technology featuring a pretightened tooth connection. The detailed description for the rod and node design is introduced in this paper, and a typical truss panel is fabricated. Under natural conditions, the short-term load test and long-term mechanical performance test for one year are performed to analyze its performance and conduct a comparative analysis for a reasonable FEM model. The study shows that the design and fabrication for the node of an assembled truss panel are convenient, safe, and reliable; because of the creep control design of the rods, not only does the short-term structural stiffness meet the design requirement but also the long-term creep deformation tends towards stability. In addition, no significant change is found in the elastic modules, so this structure can be applied in actual engineering. Although the safety factor for the strength of the composite rods is very large, it has a lightweight advantage over the steel truss for the low density of GFRP. In the FEM model, simplifying the node as a hinge connection relatively conforms to the actual status.