An Effective Acid-Base-Induced Liquid-Liquid Microextraction Based on Deep Eutectic Solvents for Determination of Testosterone and Methyltestosterone in Milk.

An environmentally friendly method for the determination of testosterone and methyltestosterone by acid-base-induced deep eutectic solvents liquid-liquid microextraction (DES-ABLLME) combining with high-performance liquid chromatography was established. The deep eutectic solvent (DES) consisting of menthol:lauric acid:decanoic acid (3:1:1) can act as both hydrogen bond donor and hydrogen bond acceptor. In this approach, ammonia solution (NH3•H2O) is used as an emulsifier to react with DESs in the extraction process to generate salt and form milky white solution, achieving high extraction efficiency. Hydrochloric acid was used as a phase separator to change the emulsification state and promote the separation of extraction agent from water phase. A series of parameters were optimized including the volume of DES and the emulsifying agent, glucose concentration as well as hydrochloric acid volume. The method was linear in the range 0.5-100 µg mL-1 with a correlation coefficient (R) of 0.9999, and the limits of detection were 0.067 and 0.2 µg mL-1 for testosterone and methyltestosterone, respectively. This method was applied to analyze testosterone and methyltestosterone in milk samples, and the recoveries were between 89.2 and 108.2%.

Development of a total serum testosterone, androstenedione, 17-hydroxyprogesterone, 11ß-hydroxyandrostenedione and 11-ketotestosterone LC-MS/MS assay and its application to evaluate pre-analytical sample stability.

Background Classically, serum testosterone (T) and androstenedione (A4) have been the mainstay for the biochemical assessment of hyperandrogenism. However, recent evidence suggests 11ß-hydroxyandrostenedione (11OHA4) and 11-ketotestosterone (11KT) may also be important. Here, we describe the development of a liquid chromatography-tandem mass spectrometry (LC-MS/MS) assay for quantitation of total serum T, A4, 17-hydroxyprogesterone (17OHP), 11OHA4 and 11KT. In addition, we applied the method to assess pre-analytical stability. Methods An isotopically labelled internal standard was added to samples prior to supported liquid extraction (SLE). Extracts were analysed using LC-MS/MS to detect T/A4/17OHP/11OHA4 and 11KT along with their corresponding internal standards. Samples (n = 7) were collected from healthy volunteers (n = 14) and left incubated at 20 °C for up to 72 h. Tubes were retrieved at select time points, centrifuged, separated and frozen prior to analysis. Results The total run time was 4 min. For all analytes, intra- and inter-assay imprecision did not exceed 7.9% and 5.3%, respectively; matrix effects were negligible and mean recoveries ranged from 95.3 to 111.6%. The limits of quantitation (LOQs) were 0.25 nmol/L for T, A4 and 11OHA4, 0.50 nmol/L for 17OHP, and 0.24 nmol/L for 11KT. No significant change was observed in pre-centrifugation A4 or female T concentrations over 72 h. Significant increases (p < 0.01) in concentrations of 11KT, 17OHP, 11OHA4 and male T were observed after 2, 8, 12 and 24 h, respectively. Conclusions We developed a robust LC-MS/MS assay for the quantitation of total serum T/A4/17OHP/11OHA4 and 11KT. Applying the method to determine pre-analytical stability suggests samples requiring 11KT need separating from the cells within 2 h.

A robust LC-MS/MS assay with online cleanup for measurement of serum testosterone.

Accurate measurement of low levels of testosterone is critical for diagnosis and treatment of androgen disorders. The very low concentrations of testosterone in children, females, and males with androgen suppression therapies necessitate the use of mass spectrometry-based methods. We aimed to develop a liquid chromatography with tandem mass spectrometry method with simplified sample preparation and online solid-phase extraction cleanup to achieve enhanced precision, accuracy, robustness, and cost-effectiveness. The assay was linear from 10 to 20 000 pg/mL with an analytical recovery of 93-104%. The total coefficient of variation was 2.5, 1.9, and 1.7% at concentration levels of 348, 5432, and 10 848 pg/mL, respectively. No significant carryover was observed from samples with concentrations up to 20 000 pg/mL. No significant interference was observed from androstenedione, dehydroepiandrosterone, epi-testosterone, and estriol. Comparison with CDC Hormone Standardization program (HoSt) reference samples with defined values (n = 40) showed a Deming regression slope of 0.963, intercept of 28.06 pg/mL, standard error of estimate was 66.9, a correlation coefficient of 0.9996, and a mean bias of -0.6%. The method met the accuracy criteria by the CDC HoSt program. In addition, we achieved >12 000 injections on a single analytical column without significant performance deterioration due to the specific online solid-phase extraction settings.

Semi-quantitative determination of designer steroids by high-performance liquid chromatography with ultraviolet detection in the absence of reference material.

New designer steroids are continually being encountered in dietary supplements that claim to increase muscle mass, but quantitative analysis of such ingredients is challenging due to the availability, quality, or cost of commercial reference materials. Although standard reference material typically becomes available for these emerging compounds, laboratories often face the challenge of finding properly certified materials from accredited suppliers, due to traceability requirements. Several of these designer steroids have been isolated and identified using multiple structural elucidation tools. Structural characteristics of these compounds of interest were evaluated and molar absorptivity data was collected and compared to several readily available steroid standards using ultraviolet/visible spectroscopy. This approach was used to find suitable compounds for use as surrogate reference materials in the semi-quantitative determination of two designer steroids, 1-dehydroepiandrosterone (1-androsterone) and 6ß-chloro-4-androsten-17ß-ol-3-one (6ß-chlorotestosterone). Laboratory-fortified matrix samples and dietary supplement samples were analyzed using this method for the estimation of 1-androsterone and 6ß-chlorotestosterone by HPLC-UV. Assay values obtained for the estimation of 1-androsterone in a dietary supplement sample using a prasterone or dehydroepiandrosterone (DHEA) standard curve were 100% of those obtained using a 1-androsterone reference standard, once it became commercially available. Estimations for 6ß-chlorotestosterone in laboratory-fortified matrix samples using a testosterone standard curve were 92%-93% of those obtained using isolated 6ß-chlorotestosterone as "reference material."

Proteomic Analysis of Charcoal-Stripped Fetal Bovine Serum Reveals Changes in the Insulin-like Growth Factor Signaling Pathway.

Charcoal-stripped fetal bovine serum (CS-FBS) is commonly used to study androgen responsiveness and androgen metabolism in cultured prostate cancer (CaP) cells. Switching CaP cells from FBS to CS-FBS may reduce the activity of androgen receptor (AR), inhibit cell proliferation, or modulate intracellular androgen metabolism. The removal of proteins by charcoal stripping may cause changes in biological functions and has not yet been investigated. Here we profiled proteins in FBS and CS-FBS using an ion-current-based quantitative platform consisting of reproducible surfactant-aided precipitation/on-pellet digestion, long-column nanoliquid chromatography separation, and ion-current-based analysis. A total of 143 proteins were identified in FBS, among which 14 proteins including insulin-like growth factor 2 (IGF-2) and IGF binding protein (IGFBP)-2 and -6 were reduced in CS-FBS. IGF-1 receptor (IGF1R) and insulin receptor were sensitized to IGFs in CS-FBS. IGF-1 and IGF-2 stimulation fully compensated for the loss of AR activity to maintain cell growth in CS-FBS. Endogenous production of IGF and IGFBPs was verified in CaP cells and clinical CaP specimens. This study provided the most comprehensive protein profiles of FBS and CS-FBS and offered an opportunity to identify new protein regulators and signaling pathways that regulate AR activity, androgen metabolism, and proliferation of CaP cells.

Zn2+-loaded cellulose beads stabilized by chitosan and prepared via freeze-drying for removing human testosterone in plasma.

Hemoperfusion using metal ion affinity adsorbent is a promising method to remove human testosterone in plasma. Due to the leakage of metal ion from the adsorbents, there is no metal ion affinity adsorbent for hemoperfusion. In this study, chitosan was used to coat the adsorbent for preventing the leakage of Zn2+ loaded. Meanwhile, freeze-drying method was used to enhance adsorption capacity of Zn2+-loaded cellulose beads for testosterone. The results indicate that after the adsorbent was coated by 0.02% chitosan solution, the highest adsorption percentage reached 48%, during adsorption, the Zn2+ concentration in plasma did not increase; the adsorption capacity of the adsorbent can be significantly enhanced by freeze-drying. The results may be caused by porosity of the adsorbent enlarged via freeze-drying and improved stability by coating with chitosan. In addition, the adsorbent shows better selectivity and storage stability and could be a potential adsorbent to treat prostate cancer.

A fluorescent, supramolecular chemosensor to follow steroid depletion in bacterial cultures.

Steroids have been identified as endocrine-disrupting agents, which are thought to impact the fertility of aquatic organisms and may even have direct effects on humans. The removal of steroids from wastewater is therefore essential, and this is most efficiently achieved by microbial treatment. We report herein a simple fluorescent method to identify microorganisms that are capable of steroid degradation and to optimize the conditions for steroid removal. The method is based on the supramolecular macrocycle cucurbit[8]uril (CB8), which can bind either the fluorescent dye berberine or a steroid in their inner cavity. In absence of steroid, the cavity is free to bind the dye, leading to a strong increase in fluorescence. In contrast, in the presence of steroid, the dye is displaced into the bulk solution. This principle affords a stable (no thermal or photodegradation was noted), fluorescent chemosensor (excitation ca. 450 nm, maximum emission at 525 nm), which can detect testosterone at concentrations > 0.7 µM. We show that this displacement principle can be applied to follow the removal of micromolar concentrations of the steroid testosterone from a bacterial culture of Buttiauxella sp. S19-1. The reliability of the chemosensor in screening applications is demonstrated by an excellent Z-factor, which was in the range of 0.52 to 0.74 for all experiments carried out with this assay. Graphical abstract Steroid depletion by bacterial cultures can be followed by fluorescence spectroscopy using a supramolecular chemosensor based on berberine and cucurbit[8]uril.

Synthesis of novel ß-cyclodextrin functionalized S, N codoped carbon dots for selective detection of testosterone.

A novel functionalized carbon dot has been synthesized by covalently linking ß-cyclodextrin to the surface of N, S codoped carbon dots (ß-CD-CDs). The characterization was confirmed by transmission electron microscopy, X-ray photoelectron spectroscopy, infrared spectra, ultraviolet-visible, and fluorescence emission spectra. On the basis of this carbon dot and (ferrocenylmethyl) trimethylammonium iodide (Fc+), a photo-induced electron transfer (PET) fluorescent probe system was developed to determine the concentration of testosterone in water and identify testosterone in cell by fluorescence imaging as a visible biomarker. Under the optimum condition, the fluorescent intensity of the probe system linearly responded to the concentration of testosterone from 0µM to 280µM and the limit of detection was 0.51µM. This probe system also performed well at determining testosterone in groundwater with average recoveries of testosterone ranging from 96% to 107% at spiking levels of 0.5-100µM, and the relative standard deviation remained below 13%, which provided a reliable, rapid and easy method to determine testosterone in environmental water. Furthermore, the low cytotoxicity, high anti-interference ability, and excellent biocompatibility of ß-CD-CDs made this probe system successfully used in cell fluorescence imaging to monitor levels of testosterone in the cytoplasm of cells with a promising application value in medical research.

Synthesis of magnetic molecularly imprinted polymers with excellent biocompatibility for the selective separation and inhibition of testosterone in prostate cancer cells.

PURPOSE: Androgen plays an important role in the progression of prostate cancer. In the present study, novel magnetic molecularly imprinted polymers (MMIPs) with good biocompatibility were produced for the selective separation and inhibition of testosterone in prostate cancer cells. MATERIALS AND METHODS: MMIPs were prepared by using magnetic nanospheres, gelatin, and testosterone as the supporting materials, functional monomer, and the template molecule, respectively. The characterization of the resultant products was investigated by transmission electron microscopy, X-ray diffraction, and vibrating sample magnetometry. To test whether MMIPs can remove testosterone in biologic samples, human LNCaP (androgen-dependent) and C4-2 (androgen-independent) prostate cancer cells were selected as cell models. The translocation of androgen receptor (AR) was detected by immunofluorescence assay, and the expression of PSA mRNA was detected by real-time quantitative polymerase chain reaction analysis. Cell flow cytometry analysis was performed to detect cell cycle arrest. RESULTS: The synthesized nanomaterials (MMIPs) possessed high crystallinity, satisfactory superparamagnetic properties, and uniform imprinted shell, and exhibited high adsorption capacity, fast kinetics, and high selectivity for testosterone. Moreover, the obtained imprinted nanomaterials could selectively enrich and detect testosterone in the LNCaP cell samples as a solid-phase extractant coupled with high-performance liquid chromatography. In addition, the MMIPs could freely enter prostate cancer cells and suppress the translocation of AR into the cell nucleus. We further found that MMIPs inhibited upregulation of AR downstream target genes in LNCaP and C4-2 cells; also, MMIPs inhibited cell growth and induced obvious cell cycle arrest in androgen-dependent LNCaP cells, but had no obvious effect on androgen-independent C4-2 cells. CONCLUSION: Our results indicate that the obtained imprinted nanomaterials can specifically and effectively bind testosterone and recover it from prostate cancer cells. Moreover, the MMIPs can freely enter prostate cancer cells and block the activation of testosterone-AR pathway. Thus, the MMIPs may be a new option for antiandrogen therapy in prostate cancer.

Sensitive simultaneous quantitation of testosterone and estradiol in serum by LC-MS/MS without derivatization and comparison with the CDC HoSt program.

BACKGROUND: Very sensitive measurements of serum estrogens and testosterone are important in adult and pediatric endocrinology and immunoassays are known to lack the required performance at very low levels. Our aim was to develop a sensitive HPLC-MS/MS assay for both estradiol (E2) and testosterone (Te) in serum without the need for chemical derivatization and using commercially available calibrators. METHODS: Serum samples were prepared by the addition of internal standards followed by extraction using hexane:ethyl acetate. Chromatographic separation was achieved using a C18 column and mass spectrometry was performed in both positive and negative ion modes. RESULTS: The lower limits of quantitation (LLOQs) of E2 and Te were 5pg/mL and 1ng/dL, respectively. The analytical measurement range (AMR) for E2 was 5-600pg/mL and 1-1,170ng/dL for Te. Assay accuracy was determined both by comparison with a LC-MS/MS method performed at a national laboratory and the CDC HoSt program. Comparison with samples analyzed by both methods showed excellent correlation. Within-day (N=10) and between-day (N=20) CVs at concentrations spanning the AMR were less than 7% for both analytes. CONCLUSION: We have developed an accurate and highly sensitive assay to measure E2 and Te levels in serum by HPLC-MS/MS without chemical derivatization and using commercially available calibrators.

Validation of Electrochemiluminiscence Immunoassay for Ovarian Steroid Determination in Rhinella arenarum.

In this work, we describe the validation of an electrochemiluminescence immunoassay (ECLIA) that allowed us for the first time to determine the levels of progesterone (P4 ) and testosterone (T) secreted by Rhinella arenarum follicles during the preovulatory (POP) and reproductive (RP) periods. We also verified the relation between P4 and T levels and oocyte maturation. Moreover, we demonstrated that the extraction protocol developed for the determinations of P4 and T by ECLIA proved to be efficient and reproducible since the efficacy of the extraction was above 95% in all assays conducted. The results indicate that in the validation process the variation coefficient (CV) between assays is compatible with the analytical procedures based on automated immunoassays (CV < 8%) and that the adaptation proposed for the samples allows the determination of T and P4 with the Cobas e-411 analyzer. Our results indicate that in basal conditions the levels of T released by R. arenarum follicles were higher than those of P4 during POP and RP. In these conditions, steroid secretion failed to induce germinal vesicle break down (GVBD) in the follicles. Under gonadotropin stimulation, steroidogenesis showed a remarkable increase in both periods, especially during POP. This increase was correlated with a high maturation percentage in the follicles incubated in vitro (GVBD = 72 ± 16%) during POP. During RP, human Chorionic Gonadotropin (hCG) induced 81.75 ± 9.1% GVBD. This study is the first report of the seasonal steroidogenic activity in the ovary of R. arenarum in situ using an ECLIA-modified protocol developed in our laboratory.

Sorption of testosterone on partially-dispersed soil particles of different size fractions: Methodology and implications.

Sorption of hormones to soil particles of different size fractions (DSFs) has been studied to understand their fate and transport (F/T) in soils. Conventional studies fractionated the soil particles into DSFs by using the high speed stirring method and/or adding surfactants to fully disperse the bulk soil. However, the natural processes (e.g., soil erosion, irrigation) often are relatively mild, and many soil particles may be still in the aggregate form. In this study, a method was developed for conducting the sorption test of a representative hormone (i.e., testosterone) to bulk soils first and then analyzing the results against DSFs. Results indicated the particle size distribution (PSD) of the two representative soils tested with partially-dispersed and fully-dispersed methods was significantly different due to the attachment of clay particles on sand and silt. Testosterone was sorbed mainly by the dominant aggregates even though they might have relatively lower sorption affinity than that of clays. However, the small particles (<2000 nm), even with ∼5% mass of the bulk soil, contributed more than 30% of sorbed testosterone in the "whole" soils. The partially-dispersed soil particles of DSFs should be used to understand the transport of hormone in runoff, because using the fully-dispersed soil particles will overestimate while the whole soil method will underestimate the transport potential. With the methodology developed in this study, the sorption tests will not compromise soil's original properties (e.g., aggregates) or the competition (e.g., sorption) among soil particles, and the contribution of DSFs (particularly the partially-dispersed aggregates) to the sorption of the "whole" soil can be determined.

A direct assay for the routine measurement of testosterone, androstenedione, dihydrotestosterone and dehydroepiandrosterone by liquid chromatography tandem mass spectrometry.

BACKGROUND: The measurement of androgens in many laboratories is often limited to testosterone. To more accurately determine the androgen status in both sexes, the measurement of other androgens such as dihydrotestosterone, the more potent metabolite of testosterone, and androstenendione and dehydroepiandrosterone, the most abundant circulating androgens in women would be informative. We report a combined liquid chromatography tandem mass spectrometry method for the measurement of these androgens. METHODS: Internal standards in methanol (10 µL) were added to 100 µL serum followed by the addition of zinc sulphate (100 µL). After mixing, 100 µL of acetonitrile was added and was further mixed. The samples were centrifuged and the steroids extracted using an automated online solid phase extraction on a C18 cartridge by a Waters Acquity with online sample manager coupled to a TQS mass spectrometer. RESULTS: Separation of the androgens was achieved by liquid chromatography. The run time was 6.5 min per sample. The lower limit of quantitation was 0.1 nmol/L for testosterone, androstenedione and dihydrotestosterone and 1 nmol/L for dehydroepiandrosterone. The coefficient of variation of the assay in serum for testosterone was <6%, androstenedione <8% and dihydrotestosterone and dehydroepiandrosterone <10%. DISCUSSION: We have developed a rapid assay for the liquid chromatography tandem mass spectrometry measurement of testosterone, androstenedione, dihydrotestosterone and dehydroepiandrosterone in a routine clinical laboratory. The assay requires a small volume of serum, and all analytes are measured simultaneously. The assay is rapid and simple to execute offering the potential for routine clinical application.

Testosterone sorption and desorption: effects of soil particle size.

Soils contain a wide range of particles of different diameters with different mobility during rainfall events. Effects of soil particles on sorption and desorption behaviors of steroid hormones have not been investigated. In this study, wet sieve washing and repeated sedimentation methods were used to fractionate the soils into five ranges. The sorption and desorption properties and related mechanisms of testosterone in batch reactors filled with fractionated soil particles were evaluated. Results of sorption and desorption kinetics indicate that small soil particles have higher sorption and lower desorption rates than that of big ones. Thermodynamic results show the sorption processes are spontaneous and exothermal. The sorption capacity ranks as clay>silt>sand, depending mainly on specific surface area and surface functional groups. The urea control test shows that hydrogen bonding contributes to testosterone sorption onto clay and silt but not on sand. Desorption tests indicate sorption is 36-65% irreversible from clay to sand. Clays have highest desorption hysteresis among these five soil fractions, indicating small particles like clays have less potential for desorption. The results provide indirect evidence on the colloid (clay)-facilitated transport of hormones (micro-pollutants) in soil environments.

Application of bar adsorptive microextraction (BAµE) for anti-doping control screening of anabolic steroids in urine matrices.

This study proposes a new analytical methodology for the determination of trace levels of testosterone (T) and epitestosterone (E) in urine matrices using bar adsorptive microextraction combined with liquid desorption followed by high-performance liquid chromatography with diode array detection (BAµE-LD/HPLC-DAD). The comparison of different sorbent coatings (five activated carbons, one styrene-divinylbenzene, two modified pyrrolidone, one ciano and one n-vinylpyrrolidone polymers) through BAµE showed that the latter phase presented much higher selectivity and capacity offering multiple mechanisms of interaction. Assays using this phase were performed on 25mL of water samples spiked at the 8.0µg/L level, yielded average recoveries of 92.1 and 93.4% for T and E, respectively, under optimized experimental conditions; BAµE (n-vinylpyrrolidone): 16h (1000rpm), pH 5.5; LD: acetonitrile, 30min under sonication treatment. From the developed analytical methodology, suitable detection limits were achieved (0.4µg/L) and good linear dynamic ranges (1.4-16.0µg/L) with remarkable determination coefficients (r(2)>0.9978). By using the standard addition methodology, the application of the present analytical approach on urine samples revealed good sensitivity. The proposed method, which operated under the floating sampling technology, proved to be a suitable sorption-based static microextraction alternative for screening T, E and the T/E ratio in urine samples for doping control purposes. The methodology showed to be easy to implement, demonstrating good reproducibility, sensitivity and robustness, allowing the possibility to choose the most selective sorbent coating according to the compounds of interest.

Evaluation of a molecularly imprinted polymer for determination of steroids in goat milk by matrix solid phase dispersion.

A molecularly imprinted polymer-matrix solid-phase dispersion methodology for simultaneous determination of five steroids in goat milk samples was proposed. Factors affecting the extraction recovery such as sample/dispersant ratio and washing and elution solvents were investigated. The molecularly imprinted polymer used as dispersant in the matrix solid-phase dispersion procedure showed high affinity to steroids, and the obtained extracts were sufficiently cleaned to be directly analyzed. Analytical separation was performed by micellar electrokinetic chromatography using a capillary electrophoresis system equipped with a diode array detector. A background electrolyte composed of borate buffer (25mM, pH 9.3), sodium dodecyl sulfate (10mM) and acetonitrile (20%) was used. The developed MIP-MSPD methodology was applied for direct determination of testosterone (T), estrone (E1), 17ß-estradiol (17ß-E2), 17α-ethinylestradiol (EE2) and progesterone (P) in different goat milk samples. Mean recoveries obtained ranged from 81% to 110%, with relative standard deviations (RSD)≤12%. The molecularly imprinted polymer-matrix solid-phase dispersion method is fast, selective, cost-effective and environment-friendly compared with other pretreatment methods used for extraction of steroids in milk.

An interlaboratory comparison between similar methods for determination of melatonin, cortisol and testosterone in saliva.

An interlaboratory comparison study for melatonin, cortisol and testosterone in saliva in which five laboratories participated is reported in this study. Each laboratory blindly measured eight samples prepared from natural saliva spiked with melatonin, cortisol and testosterone in the range 0-579 pmol/L for melatonin, 0-90 nmol/L for cortisol, and 0-622 pmol/L for testosterone. The recovery of spiked material for melatonin ranged from 91-110%, from 83-100% for cortisol and from 80-94% for testosterone. The content of natural hormone in saliva was estimated to be between 0.278 and 6.90 pmol/L for melatonin, 0.56 and 6.72 nmol/L for cortisol and 11.9 and 73.8 pmol/L for testosterone. This indicates a large interlaboratory variation. The present study emphasizes the importance of external quality control for the analysis of melatonin, cortisol and testosterone in saliva.

Investigating the binding behaviour of two avidin-based testosterone binders using molecular recognition force spectroscopy.

Molecular recognition force spectroscopy, a biosensing atomic force microscopy technique allows to characterise the dissociation of ligand-receptor complexes at the molecular level. Here, we used molecular recognition force spectroscopy to study the binding capability of recently developed testosterone binders. The two avidin-based proteins called sbAvd-1 and sbAvd-2 are expected to bind both testosterone and biotin but differ in their binding behaviour towards these ligands. To explore the ligand binding and dissociation energy landscape of these proteins, we tethered biotin or testosterone to the atomic force microscopy probe while the testosterone-binding protein was immobilized on the surface. Repeated formation and rupture of the ligand-receptor complex at different pulling velocities allowed determination of the loading rate dependence of the complex-rupturing force. In this way, we obtained the molecular dissociation rate (k(off)) and energy landscape distances (x(ß)) of the four possible complexes: sbAvd-1-biotin, sbAvd-1-testosterone, sbAvd-2-biotin and sbAvd-2-testosterone. It was found that the kinetic off-rates for both proteins and both ligands are similar. In contrast, the x(ß) values, as well as the probability of complex formations, varied considerably. In addition, competitive binding experiments with biotin and testosterone in solution differ significantly for the two testosterone-binding proteins, implying a decreased cross-reactivity of sbAvd-2. Unravelling the binding behaviour of the investigated testosterone-binding proteins is expected to improve their usability for possible sensing applications.

Chemometric evaluation of urinary steroid hormone levels as potential biomarkers of neuroendocrine tumors.

Neuroendocrine tumors (NETs) are uncommon tumors which can secrete specific hormone products such as peptides, biogenic amines and hormones. So far, the diagnosis of NETs has been difficult because most NET markers are not specific for a given tumor and none of the NET markers can be used to fulfil the criteria of high specificity and high sensitivity for the screening procedure. However, by combining the measurements of different NET markers, they become highly sensitive and specific diagnostic tests. The aim of the work was to identify whether urinary steroid hormones can be identified as potential new biomarkers of NETs, which could be used as prognostic and clinical course monitoring factors. Thus, a rapid and sensitive reversed-phase high-performance liquid chromatographic method (RP-HPLC) with UV detection has been developed for the determination of cortisol, cortisone, corticosterone, testosterone, epitestosterone and progesterone in human urine. The method has been validated for accuracy, precision, selectivity, linearity, recovery and stability. The limits of detection and quantification were 0.5 and 1 ng mL-1 for each steroid hormone, respectively. Linearity was confirmed within a range of 1-300 ng mL-1 with a correlation coefficient greater than 0.9995 for all analytes. The described method was successfully applied for the quantification of six endogenous steroid levels in human urine. Studies were performed on 20 healthy volunteers and 19 patients with NETs. Next, for better understanding of tumor biology in NETs and for checking whether steroid hormones can be used as potential biomarkers of NETs, a chemometric analysis of urinary steroid hormone levels in both data sets was performed.

Immunoextraction of testosterone and epitestosterone from human urine sample based on polyamidoamine modified silica.

Polyamidoamine dendrimer (PAMAM) is one of a number of dendritic polymers with precise molecular structure, highly geometric symmetry, and a large number of terminal groups. The polyamidoamine modified silica was synthesized with microwave assisted protocol. Anti-epitestosterone monoclonal antibodies were immobilized onto the PAMAM grafted silica and prepared an off-line immunoextraction column that applied in the extraction of testosterone and epitestosterone. The results showed that the affinity activity of the anti-epitestosterone monoclonal antibodies was remained at high level after immobilization. It was satisfactory to apply this new type of immunoextraction column to analyze testosterone and epitestosterone in spiked urine sample.