Microengineering Laser Plasma Interactions at Relativistic Intensities.

We report on the first successful proof-of-principle experiment to manipulate laser-matter interactions on microscales using highly ordered Si microwire arrays. The interaction of a high-contrast short-pulse laser with a flat target via periodic Si microwires yields a substantial enhancement in both the total and cutoff energies of the produced electron beam. The self-generated electric and magnetic fields behave as an electromagnetic lens that confines and guides electrons between the microwires as they acquire relativistic energies via direct laser acceleration.

Experimental capabilities of 0.4 PW, 1 shot/min Scarlet laser facility for high energy density science.

We report on the recently completed 400 TW upgrade to the Scarlet laser at The Ohio State University. Scarlet is a Ti:sapphire-based ultrashort pulse system that delivers >10 J in 30 fs pulses to a 2 µm full width at half-maximum focal spot, resulting in intensities exceeding 5×1021 W/cm2. The laser fires at a repetition rate of once per minute and is equipped with a suite of on-demand and on-shot diagnostics detailed here, allowing for rapid collection of experimental statistics. As part of the upgrade, the entire laser system has been redesigned to facilitate consistent, characterized high intensity data collection at high repetition rates. The design and functionality of the laser and target chambers are described along with initial data from commissioning experimental shots.

Effect of target material on fast-electron transport and resistive collimation.

The effect of target material on fast-electron transport is investigated using a high-intensity (0.7 ps, 10(20) W/cm2) laser pulse irradiated on multilayered solid Al targets with embedded transport (Au, Mo, Al) and tracer (Cu) layers, backed with millimeter-thick carbon foils to minimize refluxing. We consistently observed a more collimated electron beam (36% average reduction in fast-electron induced Cu Kα spot size) using a high- or mid-Z (Au or Mo) layer compared to Al. All targets showed a similar electron flux level in the central spot of the beam. Two-dimensional collisional particle-in-cell simulations showed formation of strong self-generated resistive magnetic fields in targets with a high-Z transport layer that suppressed the fast-electron beam divergence; the consequent magnetic channels guided the fast electrons to a smaller spot, in good agreement with experiments. These findings indicate that fast-electron transport can be controlled by self-generated resistive magnetic fields and may have important implications to fast ignition.

Dynamics of relativistic laser-plasma interaction on solid targets.

A novel time-resolved diagnostic is used to record the critical surface motion during picosecond-scale relativistic laser interaction with a solid target. Single-shot measurements of the specular light show a redshift decreasing with time during the interaction, corresponding to a slowing-down of the hole boring process into overdense plasma. On-shot full characterization of the laser pulse enables simulations of the experiment without any free parameters. Two-dimensional particle-in-cell simulations yield redshifts that agree with the data, and support a simple explanation of the slowing-down of the critical surface based on momentum conservation between ions and reflected laser light.

Scaling hot-electron generation to high-power, kilojoule-class laser-solid interactions.

Thin-foil targets were irradiated with high-power (1 ≤ P(L) ≤ 210 TW), 10-ps pulses focused to intensities of I>10(18) W/cm(2) and studied with K-photon spectroscopy. Comparing the energy emitted in K photons to target-heating calculations shows a laser-energy-coupling efficiency to hot electrons of η(L-e) = 20 ± 10%. Time-resolved x-ray emission measurements suggest that laser energy is coupled to hot electrons over the entire duration of the incident laser drive. Comparison of the K-photon emission data to previous data at similar laser intensities shows that η(L-e) is independent of laser-pulse duration from 1 ≤ τ(p) ≤ 10 ps.

Limitation on prepulse level for cone-guided fast-ignition inertial confinement fusion.

The viability of fast-ignition (FI) inertial confinement fusion hinges on the efficient transfer of laser energy to the compressed fuel via multi-MeV electrons. Preformed plasma due to the laser prepulse strongly influences ultraintense laser plasma interactions and hot electron generation in the hollow cone of an FI target. We induced a prepulse and consequent preplasma in copper cone targets and measured the energy deposition zone of the main pulse by imaging the emitted K_{alpha} radiation. Simulation of the radiation hydrodynamics of the preplasma and particle in cell modeling of the main pulse interaction agree well with the measured deposition zones and provide an insight into the energy deposition mechanism and electron distribution. It was demonstrated that a under these conditions a 100 mJ prepulse eliminates the forward going component of approximately 2-4 MeV electrons.

Towards manipulating relativistic laser pulses with micro-tube plasma lenses.

Efficient coupling of intense laser pulses to solid-density matter is critical to many applications including ion acceleration for cancer therapy. At relativistic intensities, the focus has been mainly on investigating various laser beams irradiating initially overdense flat interfaces with little or no control over the interaction. Here, we propose a novel approach that leverages recent advancements in 3D direct laser writing (DLW) of materials and high contrast lasers to manipulate the laser-matter interactions on the micro-scales. We demonstrate, via simulations, that usable intensities ≥10(23) Wcm(-2) could be achieved with current tabletop lasers coupled to micro-engineered plasma lenses. We show that these plasma optical elements act as a lens to focus laser light. These results open new paths to engineering light-matter interactions at ultra-relativistic intensities.

Effects of front-surface target structures on properties of relativistic laser-plasma electrons.

We report the results of a study of the role of prescribed geometrical structures on the front of a target in determining the energy and spatial distribution of relativistic laser-plasma electrons. Our three-dimensional particle-in-cell simulation studies apply to short-pulse, high-intensity laser pulses, and indicate that a judicious choice of target front-surface geometry provides the realistic possibility of greatly enhancing the yield of high-energy electrons while simultaneously confining the emission to narrow (<5°) angular cones.

Note: Characterization of a high-photon-energy X-ray imager.

The Bragg angle, rocking curve, and reflection efficiency of a quartz crystal x-ray imager (Miller indices 234) were measured at photon energy of 15.6909 keV, corresponding to the K(α2) line of Zr, using the X15A beamline at the National Synchrotron Light Source at Brookhaven National Laboratory. One flat and three spherically curved samples were tested. The peak reflectivity of the best-performing crystal was determined to be (3.6 ± 0.7) × 10(-4) with a rocking-curve full width at half maximum of 0.09°. The Zr K(α2) emission was imaged from a hot Zr plasma generated by a 10-J multiterawatt laser.

Coupling of high-intensity laser light to fast electrons in cone-guided fast ignition.

Cu wires attached to Al cones are used to investigate the energy coupling efficiency of laser light to fast electrons through a cone into a dense plasma. We present experimental and simulation results demonstrating the effect on the energy coupling of effectively placing the cone in a surrounding high density plasma as well as the effect of a large preformed plasma inside the cone. Thick cone walls, simulating plasma surrounding the cone in fast ignition, reduce the energy coupling by a factor of up to 4. An increase in prepulse inside the cone by a factor of 50 further reduces coupling by a factor of 3. Simulations with the pic code lsp that include the laser plasma interaction and the preformed plasma from the flash code show that electron refluxing in thin cone-wall targets enhances coupling to the wire. The implications for full-scale cone-guided fast ignition are discussed.

Time dependence of fast electron beam divergence in ultraintense laser-plasma interactions.

We report on the measurement and computer simulation of the divergence of fast electrons generated in an ultraintense laser-plasma interaction (LPI) and the subsequent propagation in a nonrefluxing target. We show that, at Iλ(2) of 10(20) Wcm(-2)µm(2), the time-integrated electron beam full divergence angle is (60±5)°. However, our time-resolved 2D particle-in-cell simulations show the initial beam divergence to be much smaller (≤30°). Our simulations show the divergence to monotonically increase with time, reaching a final value of (68±7)° after the passage of the laser pulse, consistent with the experimental time-integrated measurements. By revealing the time-dependent nature of the LPI, we find that a substantial fraction of the laser energy (~7%) is transported up to 100 µm with a divergence of 32°.

A novel zirconium Kα imager for high energy density physics research.

We report on the development and characterization of a zirconium Kα imager for high energy density physics research. The imager consists of a spherically bent quartz crystal operating at 15.7 keV photon energy. We compare the performance of the imager in terms of integrated reflectivity (R(int)) and temperature dependent collection efficiency (η(Te)) to that of the widely used Cu Kα imager. Our collisional-radiative simulations show that the new imager can be reliably used up to 250 eV plasma temperature. Monte Carlo simulations show that for a 25 µm thick tracer layer of zirconium, the contribution to Kα production from photo-pumping is only 2%. We present, for the first time, 2D spatially resolved images of zirconium plasmas generated by a high intensity short pulse laser interacting with Zr solid targets.

A dual-channel, curved-crystal spectrograph for petawatt laser, x-ray backlighter source studies.

A dual-channel, curved-crystal spectrograph was designed to measure time-integrated x-ray spectra in the approximately 1.5 to 2 keV range (6.2-8.2 A wavelength) from small-mass, thin-foil targets irradiated by the VULCAN petawatt laser focused up to 4x10(20) W/cm(2). The spectrograph consists of two cylindrically curved potassium-acid-phthalate crystals bent in the meridional plane to increase the spectral range by a factor of approximately 10 compared to a flat crystal. The device acquires single-shot x-ray spectra with good signal-to-background ratios in the hard x-ray background environment of petawatt laser-plasma interactions. The peak spectral energies of the aluminum He(alpha) and Ly(alpha) resonance lines were approximately 1.8 and approximately 1.0 mJ/eV sr (approximately 0.4 and 0.25 J/A sr), respectively, for 220 J, 10 ps laser irradiation.

Effect of reentrant cone geometry on energy transport in intense laser-plasma interactions.

The energy transport in cone-guided low- Z targets has been studied for laser intensities on target of 2.5x10(20) W cm(-2). Extreme ultraviolet (XUV) imaging and transverse optical shadowgraphy of the rear surfaces of slab and cone-slab targets show that the cone geometry strongly influences the observed transport patterns. The XUV intensity showed an average spot size of 65+/-10 microm for slab targets. The cone slabs showed a reduced spot size of 44+/-10 microm. The shadowgraphy for the aforementioned shots demonstrate the same behavior. The transverse size of the expansion pattern was 357+/-32 microm for the slabs and reduced to 210+/-30 microm. A transport model was constructed which showed that the change in transport pattern is due to suppression of refluxing electrons in the material surrounding the cone.

A Bremsstrahlung spectrometer using k-edge and differential filters with image plate dosimeters.

A Bremsstrahlung spectrometer using k-edge and differential filtering has been used with image plate dosimeters to measure the x-ray fluence from short-pulse laser/target interactions. An electron spectrometer in front of the Bremsstrahlung spectrometer deflects electrons from the x-ray line of sight and simultaneously measures the electron spectrum. The response functions were modeled with the Monte Carlo code INTEGRATED TIGER SERIES 3.0 and the dosimeters calibrated with radioactive sources. An electron distribution with a slope temperature of 1.3 MeV is inferred from the Bremsstrahlung spectra.

Electron heated target temperature measurements in petawatt laser experiments based on extreme ultraviolet imaging and spectroscopy.

Three independent methods (extreme ultraviolet spectroscopy, imaging at 68 and 256 eV) have been used to measure planar target rear surface plasma temperature due to heating by hot electrons. The hot electrons are produced by ultraintense laser-plasma interactions using the 150 J, 0.5 ps Titan laser. Soft x-ray spectroscopy in the 50-400 eV region and imaging at the 68 and 256 eV photon energies give a planar deuterated carbon target rear surface pre-expansion temperature in the 125-150 eV range, with the rear plasma plume averaging a temperature approximately 74 eV.

Determination of electron-heated temperatures of petawatt laser-irradiated foil targets with 256 and 68 eV extreme ultraviolet imaging.

Measurements of plasma temperature at the rear surface of foil targets due to heating by hot electrons, which were produced in short pulse high intensity laser matter interactions using the 150 J, 0.5 ps Titan laser, are reported. Extreme ultraviolet (XUV) imaging at 256 and 68 eV energies is used to determine spatially resolved target rear surface temperature patterns by comparing absolute intensities to radiation hydrodynamic modeling. XUV mirrors at these two energies were absolutely calibrated at the Advanced Light Source at the Lawrence Berkeley Laboratory. Temperatures deduced from both imagers are validated against each other within the range of 75-225 eV.

Diagnostics for fast ignition science (invited).

The ignition concept for electron fast ignition inertial confinement fusion requires sufficient energy be transferred from an approximately 20 ps laser pulse to the compressed fuel via approximately MeV electrons. We have assembled a suite of diagnostics to characterize such transfer, simultaneously fielding absolutely calibrated extreme ultraviolet multilayer imagers at 68 and 256 eV; spherically bent crystal imagers at 4.5 and 8 keV; multi-keV crystal spectrometers; MeV x-ray bremmstrahlung, electron and proton spectrometers (along the same line of sight), and a picosecond optical probe interferometer. These diagnostics allow careful measurement of energy transport and deposition during and following the laser-plasma interactions at extremely high intensities in both planar and conical targets. Together with accurate on-shot laser focal spot and prepulse characterization, these measurements are yielding new insights into energy coupling and are providing critical data for validating numerical particle-in-cell (PIC) and hybrid PIC simulation codes in an area crucial for fast ignition and other applications. Novel aspects of these diagnostics and how they are combined to extract quantitative data on ultrahigh intensity laser-plasma interactions are discussed.

Laser heating of solid matter by light-pressure-driven shocks at ultrarelativistic intensities.

The heating of solid targets irradiated by 5 x 10(20) W cm(-2), 0.8 ps, 1.05 microm wavelength laser light is studied by x-ray spectroscopy of the K-shell emission from thin layers of Ni, Mo, and V. A surface layer is heated to approximately 5 keV with an axial temperature gradient of 0.6 microm scale length. Images of Ni Ly(alpha) show the hot region has 100 G bar light pressure compresses the preformed plasma and drives a shock into the solid, heating a thin layer.

Effect of laser intensity on fast-electron-beam divergence in solid-density plasmas.

Metal foil targets were irradiated with 1 mum wavelength (lambda) laser pulses of 5 ps duration and focused intensities (I) of up to 4x10;{19} W cm;{-2}, giving values of both Ilambda;{2} and pulse duration comparable to those required for fast ignition inertial fusion. The divergence of the electrons accelerated into the target was determined from spatially resolved measurements of x-ray K_{alpha} emission and from transverse probing of the plasma formed on the back of the foils. Comparison of the divergence with other published data shows that it increases with Ilambda;{2} and is independent of pulse duration. Two-dimensional particle-in-cell simulations reproduce these results, indicating that it is a fundamental property of the laser-plasma interaction.