Strength of interference screw fixation of meniscus prosthesis matches native meniscus attachments.

PURPOSE: Meniscal surgery is one of the most common orthopaedic surgical interventions. Total meniscus replacements have been proposed as a solution for patients with irreparable meniscal injuries. Reliable fixation is crucial for the success and functionality of such implants. The aim of this study was to characterise an interference screw fixation system developed for a novel fibre-matrix-reinforced synthetic total meniscus replacement in an ovine cadaveric model. METHODS: Textile straps were tested in tension to failure (n = 15) and in cyclic tension (70-220 N) for 1000 cycles (n = 5). The textile strap-interference screw fixation system was tested in 4.5 mm-diameter single anterior and double posterior tunnels in North of England Mule ovine tibias aged > 2 years using titanium alloy (Ti6Al4Va) and polyether-ether-ketone (PEEK) screws (n ≥ 5). Straps were preconditioned, dynamically loaded for 1000 cycles in tension (70-220 N), the fixation slippage under cyclic loading was measured, and then pulled to failure. RESULTS: Strap stiffness was at least 12 times that recorded for human meniscal roots. Strap creep strain at the maximum load (220 N) was 0.005 following 1000 cycles. For all tunnels, pull-out failure resulted from textile strap slippage or bone fracture rather than strap rupture, which demonstrated that the textile strap was comparatively stronger than the interference screw fixation system. Pull-out load (anterior 544 ± 119 N; posterior 889 ± 157 N) was comparable to human meniscal root strength. Fixation slippage was within the acceptable range for anterior cruciate ligament graft reconstruction (anterior 1.9 ± 0.7 mm; posterior 1.9 ± 0.5 mm). CONCLUSION: These findings show that the textile attachment-interference screw fixation system provides reliable fixation for a novel ovine meniscus implant, supporting progression to in vivo testing. This research provides a baseline for future development of novel human meniscus replacements, in relation to attachment design and fixation methods. The data suggest that surgical techniques familiar from ligament reconstruction may be used for the fixation of clinical meniscal prostheses.

Isolated popliteus tendon injury does not lead to abnormal laxity in posterior-stabilised total knee arthroplasty.

PURPOSE: The popliteus tendon is crucial to postero-lateral stability and prone to iatrogenic injury intra-operatively. Its role in the stability of the replaced knee remains contentious. The aim of this study was to use computer navigation to quantify the effect of popliteus sectioning on the 'envelope of laxity' (EoL) offered by a posterior-stabilised (PS) total knee arthroplasty (TKA) and compare with that of the native knee. METHODS: Loaded cadaveric legs were mounted on a purpose built rig. EoL was measured in 3 degrees of freedom using computer navigation. Knees were subjectively stressed in varus/valgus, internal/external rotation and anterior draw. This was performed preoperatively, during TKA and after sectioning of the popliteus tendon. Real-time data were recorded at 0°, 30°, 60° and 90° of flexion as the operating surgeon stressed the knee in 3 degrees of freedom to its subjective endpoint. Mixed-effect modelling was used to quantify the effects of intervention on degree of laxity. RESULTS: In all conditions, there was an increase in laxity with knee flexion. Insertion of a PS TKA resulted in increased constraint, particularly in rotation. Sectioning of the popliteus did not result in a significant increase in knee laxity to 90º of knee flexion. However, at deeper flexion angles, tendon sectioning overcame the constraints of the implant resulting in a significant increase in rotatory and varus/valgus laxity towards the native condition. CONCLUSION: These findings support the view that certain current designs of PS knee replacement can constrain the knee in flexion in the absence of postero-lateral deficiency. For this implant, isolated sectioning of the popliteus tendon did not substantially generate abnormal knee laxity.

Can we define envelope of laxity during navigated knee arthroplasty?

PURPOSE: Functional outcomes after knee arthroplasty (TKA) remain poor. The ability to restore the soft tissue envelope intraoperatively may improve such outcomes. The aim of this study was to extend the scope of computer navigation as a tool to quantifying the envelope of laxity during subjective stress testing preoperatively and to quantify the effects of knee replacement and how it changes as a result of ligamentous failure. METHODS: Loaded cadaveric legs were mounted on a purpose-built rig. Envelope of laxity was measured in 3 degrees of freedom using computer navigation. Knees were subjectively stressed in varus/valgus, internal/external rotation and anterior draw. This was performed preoperatively, during TKA and after sequential sectioning of ligaments. Real-time data were recorded at 0°, 30°, 60° and 90° of flexion. Mixed effect modelling was used to quantify the effects of intervention on degree of laxity. RESULTS: In all cases, there was an increase in laxity with increasing flexion or ligament sectioning. Operator and movement cycle had no effect. Insertion of a TKA showed increased stability within the joint, especially in internal/external rotation and anterior drawer. Once the PCL and popliteus were cut, the implant only maintained some rotatory stability; thereafter, the soft tissue envelope failed. CONCLUSIONS: This work has shown a novel way by which computer navigation can be used to analyse soft tissue behaviour during TKA beyond the coronal plane and throughout range of motion. Despite subjective stress testing, our results show reproducible patterns of soft tissue behaviour-in particular a wide range of mid-flexion excursion. It also quantifies the limits within which a cruciate-retaining TKR can maintain knee stability. This functionality may guide the surgeon in identifying and/or preventing soft tissue imbalances intra-operatively, improving functional results.

No difference in patellar tracking between symmetrical and asymmetrical femoral component designs in TKA.

PURPOSE: Poor knee extension function after total knee arthroplasty (TKA) is associated with factors including articular geometry and alignment. Femoral trochlear geometry has evolved from symmetrical to become more prominent proximal-laterally, with the groove aligned proximal-lateral to distal-medial. This study in vitro tested the hypothesis that a modern asymmetrical prosthesis would restore patellar tracking and stability to more natural behaviour than an older symmetrical prosthesis. METHODS: Six knees had their patellar tracking measured optically during active knee extension. Medial-lateral force versus displacement stability was measured at fixed angles of knee flexion. The measurements were repeated after inserting each of the symmetrical and asymmetrical TKAs. RESULTS: Significant differences of patellar lateral displacement stability, compared to normal, were not found at any angle of knee flexion. The patella tracked medial-laterally within 2.5 mm of the natural path with both TKAs. However, for both TKAs near knee extension, the patella was tilted laterally by approximately 6° and was also flexed approximately 8° more than in the natural knee. CONCLUSION: The hypothesis was not supported: The more anatomical component design did not provide more anatomical patellar kinematics and stability.

A biomechanical basis for tears of the human acetabular labrum.

OBJECTIVE: Acetabular labral tears predominantly affect young patients and are a source of hip pain in the athlete. Four causes of the initiation of labral tears have been proposed; trauma, hypolaxity of the anterior capsule, dysplasia and bony impingement. A further cause could be reduced biomechanical properties in the area most susceptible to tears. However, no work has defined these properties. DESIGN: 32 compressive and 32 tensile test samples were harvested from fresh-frozen cadaveric acetabula. The labrum was divided into eight areas to allow comparison around its circumference. Semiconfined compressive testing and tensile testing were performed at a displacement rate of 10 mm/min in a controlled environment of 100% humidity at 37 (SD 1) degrees C. SETTING: Cadaveric study. RESULTS: The mean compressive stiffness was 31.75 (SD 16.7) MPa, and the mean tensile elastic modulus was 24.7 (SD 10.8) MPa. The anterosuperior region had a significantly lower compressive elastic modulus than either of the posterior quadrants (p<0.05) and a significantly lower tensile modulus to the anterioinferior area (p<0.05). CONCLUSIONS: The biomechanical properties in the anterosuperior region may be a contributing factor to the initiation of labral tears.

Tensile properties of the human glenoid labrum.

Human fresh-frozen cadaveric glenoid labrae from 16 donors were harvested and ten of these had no gross degeneration. These ten were divided into eight equal circumferential sections. Each section was cut to produce test-samples from the core layer with a cross-section of 1 x 1 mm. Tensile testing was performed within a controlled environment unit at 37 +/- 1 degrees C and 100% relative humidity. Each test-sample was precycled to a quasi-static state to alleviate the effects of deep-freezing, prior to final testing. The tangent modulus was calculated for each test-sample before and after a 5-min period of stress relaxation and at yield. The mean elastic modulus and yield stress of the glenoid labrum were 22.8 +/- 11.4 and 2.5 +/- 2.1 MPa, respectively. The anterosuperior portion had a lower elastic modulus and lower yield stress than the inferior portion (both P < 0.02). The pre-stress relaxation tangent modulus was significantly lower than the post-stress relaxation tangent modulus for all portions of the labrum. The glenoid labrum has similar tensile material properties to articular cartilage. Its elastic modulus varies around its circumference. This suggests that the labrum may encounter different forces at different positions.

Pre-clinical assessment of total knee replacement anterior-posterior constraint.

Pre-clinical, bench-top assessment of Total Knee Replacements (TKR) can provide information about the inherent constraint provided by a TKR, which does not depend on the condition of the patient undergoing the arthroplasty. However little guidance is given by the ASTM standard on test configurations such as medial-lateral (M:L) loading distribution, flexion angle or restriction of secondary motions. Using a purpose built rig for a materials testing machine, four TKRs currently in widespread clinical use, including medial-pivot and symmetrical condyle types, were tested for anterior-posterior translational constraint. Compressive joint loads from 710 to 2000 N, and a range of medial-lateral (M:L) load distributions, from 70:30% to 30:70% M:L, were applied at different flexion angles with secondary motions unconstrained. It was found that TKA constraint was significantly less at 60 and 90° flexion than at 0°, whilst increasing the compressive joint load increased the force required to translate the tibia to limits of AP constraint at all flexion angles tested. Additionally when M:L load distribution was shifted medially, a coupled internal rotation was observed with anterior translation and external rotation with posterior translation. This paper includes some recommendations for future development of pre-clinical testing methods.

Developments in shoulder arthroplasty.

Indications for shoulder arthroplasty are numerous, mainly owing to glenohumeral osteoarthritis, rheumatoid arthritis, or fracture of the proximal humerus. However, the anatomy and the biomechanics of the shoulder are complex and shoulder arthroplasty has evolved significantly over the past 30 years. This paper presents the main recent evolutions in shoulder replacement, the questions not answered yet, and the main future areas of research. The review focuses firstly on the design, positioning, and fixation of the humeral component, secondly on the design, positioning, and fixation of the glenoid implant, and thirdly on other concepts of shoulder arthroplasty such as the reversed prosthesis, the cementless surface replacement arthroplasty, and the bipolar arthroplasty. This review demonstrates that more research is needed. Although, in the long term, large randomized trials are needed to settle the fundamental questions of what type of replacement and which kind of fixation should be used, biomechanical research in the laboratory should be focused primarily on the comprehension of glenoid loosening, which is a major cause of total shoulder arthroplasty failure, and the significance of radiolucent lines which are often seen but with no clear understanding about their relation with failure.

Measurement of laxity in the anterior cruciate ligament-deficient knee: a comparison of three different methods in vitro.

The aim of this study was to compare in-vitro measurements of anteroposterior laxity in the anterior cruciate ligament (ACL)-deficient knee using three different methods: an Instron materials-testing machine, then a KT-2000 arthrometer, and finally by Roentgen stereophotogrammetric analysis (RSA). Eight ACL-deficient human cadaver knees were used. Total displacement was measured between 90 N anterior and 90 N posterior tibiofemoral drawer forces at both 20 degrees and 90 degrees knee flexion. Laxity ranged from 11.5 to 27.6 mm at 20 degrees and from 8.7 to 23.9 mm at 90degrees. A statistically significant difference was not found between the mean RSA and KT-2000 measurements. However, the mean Instron measurements of laxity were significantly (3-4 mm) higher than both RSA and KT-2000 measurements. The clinical methods of RSA and the KT-2000 measurements agreed well but appeared to underestimate tibiofemoral anteroposterior laxity compared with the materials-testing machine. These findings may be helpful in the future comparison of different studies.

The consequences of meniscectomy.

The menisci of the knee have an important role in load-bearing and shock absorption within the joint. They may also function as secondary stabilisers, have a proprioceptive role, and aid the lubrication and nutrition of the articular cartilage. Complete or partial loss of a meniscus can have damaging effects on a knee, leading to serious long-term sequelae. This paper reviews the consequences of meniscectomy and summarises the body of evidence in the literature regarding those factors most relevant to long-term outcome.

The effects of articular, retinacular, or muscular deficiencies on patellofemoral joint stability: a biomechanical study in vitro.

Normal function of the patellofemoral joint is maintained by a complex interaction between soft tissues and articular surfaces. No quantitative data have been found on the relative contributions of these structures to patellar stability. Eight knees were studied using a materials testing machine to displace the patella 10 mm laterally and medially and measure the force required. Patellar stability was tested from 0 degrees to 90 degrees knee flexion with the quadriceps tensed to 175 N. Four conditions were examined: intact, vastus medialis obliquus relaxed, flat lateral condyle, and ruptured medial retinaculae. Abnormal trochlear geometry reduced the lateral stability by 70% at 30 degrees flexion, while relaxation of vastus medialis obliquus caused a 30% reduction. Ruptured medial retinaculae had the largest effect at 0 degrees flexion with 49% reduction. There was no effect on medial stability. There is a complex interaction between these structures, with their contributions to loss of lateral patellar stability varying with knee flexion.

Tensile strength of the medial patellofemoral ligament before and after repair or reconstruction.

The tensile strength of the medial patellofemoral ligament (MPFL), and of surgical procedures which reconstitute it, are unknown. Ten fresh cadaver knees were prepared by isolating the patella, leaving only the MPFL as its attachment to the medial femoral condyle. The MPFL was either repaired by using a Kessler suture or reconstructed using either bone anchors or one of two tendon grafting techniques. The tensile strength and the displacement to peak force of the MPFL were then measured using an Instron materials-testing machine. The MPFL was found to have a mean tensile strength of 208 N (SD 90) at 26 mm (SD 7) of displacement. The strengths of the other techniques were: sutures alone, 37 N (SD 27); bone anchors plus sutures, 142 N (SD 39); blind-tunnel tendon graft, 126 N (SD 21); and through-tunnel tendon graft, 195 N (SD 66). The last was not significantly weaker than the MPFL itself.

The porcine forelimb as a model for human flexor tendon surgery.

Technical skills have been shown to transfer very well from bench models to practical use. The central two rays of 30 forelimbs of pigs were dissected and anatomical observations were made. The rays contained deep and superficial flexor tendons enclosed in a fibro-osseous tunnel and these were present in all 60 specimens. The fibrous part of the tunnel had specific constant condensations in annular and oblique directions which were present in all 60 rays. The anatomy of the porcine forelimb digital flexor tendon system is sufficiently similar to the human system to be used as a model for surgeons wishing to master the technical aspects of zone II flexor tendon repair. This paper proposes the porcine forelimb as a bench model for zone II flexor tendon repair.

The capsular ligaments provide more hip rotational restraint than the acetabular labrum and the ligamentum teres : an experimental study.

In this in vitro study of the hip joint we examined which soft tissues act as primary and secondary passive rotational restraints when the hip joint is functionally loaded. A total of nine cadaveric left hips were mounted in a testing rig that allowed the application of forces, torques and rotations in all six degrees of freedom. The hip was rotated throughout a complete range of movement (ROM) and the contributions of the iliofemoral (medial and lateral arms), pubofemoral and ischiofemoral ligaments and the ligamentum teres to rotational restraint was determined by resecting a ligament and measuring the reduced torque required to achieve the same angular position as before resection. The contribution from the acetabular labrum was also measured. Each of the capsular ligaments acted as the primary hip rotation restraint somewhere within the complete ROM, and the ligamentum teres acted as a secondary restraint in high flexion, adduction and external rotation. The iliofemoral lateral arm and the ischiofemoral ligaments were primary restraints in two-thirds of the positions tested. Appreciation of the importance of these structures in preventing excessive hip rotation and subsequent impingement/instability may be relevant for surgeons undertaking both hip joint preserving surgery and hip arthroplasty.

A comparative study of the effects of different bioactive fillers in PLGA matrix composites and their suitability as bone substitute materials: A thermo-mechanical and in vitro investigation.

Bone substitute composite materials with poly(L-lactide-co-glycolide) (PLGA) matrices and four different bioactive fillers: CaCO3, hydroxyapatite (HA), 45S5 Bioglass(®) (45S5 BG), and ICIE4 bioactive glass (a lower sodium glass than 45S5 BG) were produced via melt blending, extrusion and moulding. The viscoelastic, mechanical and thermal properties, and the molecular weight of the matrix were measured. Thermogravimetric analysis evaluated the effect of filler composition on the thermal degradation of the matrix. Bioactive glasses caused premature degradation of the matrix during processing, whereas CaCO3 or HA did not. All composites, except those with 45S5 BG, had similar mechanical strength and were stiffer than PLGA alone in compression, whilst all had a lower tensile strength. Dynamic mechanical analysis demonstrated an increased storage modulus (E') in the composites (other than the 45S5 BG filled PLGA). The effect of water uptake and early degradation was investigated by short-term in vitro aging in simulated body fluid, which indicated enhanced water uptake over the neat polymer; bioactive glass had the greatest water uptake, causing matrix plasticization. These results enable a direct comparison between bioactive filler type in poly(α-hydroxyester) composites, and have implications when selecting a composite material for eventual application in bone substitution.

Fatigue fracture of a femoral sliding compression screw-plate device after bone union.

A failure of a femoral screw compression plate is described, the first such case to be reported after bone union. A fatigue fracture had started from an internal screw thread, near a keyway. Design improvements, such as lengthening the barrel around the lag screw, are suggested. The question as to whether keyways are necessary for the function of such devices is discussed. The morbidity of removal operations in elderly patients means that fatigue life improvements are needed, to avoid increasing numbers of failed implants in the continuing epidemic of fractures of the proximal femur.

Evaluation of preserved bovine tendon xenografts: a histological, biomechanical and clinical study.

Glutaraldehyde treated bovine tendon xenografts have been introduced into clinical trials as human knee ligament replacements recently, following animal experiments. This paper reports a further clinical study in which complications arose from implant debris. A laboratory study showed that the implants were not absorbed or integrated into the tissues of the host animals, as had been claimed by the originators. Mechanical tests of tendon reconstructions showed that the implants were not functional. It was concluded that this material is not suitable for clinical use within the knee joint as a cruciate ligament prosthesis.

Quantitative study of the quadriceps muscles and trochlear groove geometry related to instability of the patellofemoral joint.

This was a quantitative study of the major anatomical structures associated with instability of the patellofemoral joint: the quadriceps muscles and the femoral trochlear groove. The attachments of the muscles to the patella, their lines of action, and their relative sizes (physiological cross-sectional areas) were found. On the basis of the physiological cross-sectional areas, it was estimated that the central muscles-the rectus femoris and vastus intermedius-contributed 35% of the quadriceps strength, with 40% from the vastus lateralis and 25% from the vastus medialis. The vastus lateralis had the most variable results, with the ratio of the lateralis to the medialis ranging from 0.90 to 2.18; this may be associated with patellar instability. Both the long and oblique parts of the vastus medialis were more oblique than the corresponding parts of the vastus lateralis. Photographic "skyline" views of the trochlear groove produced data on the sulcus angle and ratio of depth to width. The data showed that the trochlear groove did not deepen in the area contacted by the patella with progressive knee flexion (p > 0.53), contrary to popular belief. These data are useful for objective analysis of patellofemoral stability and related surgical interventions.

Quantitative measurement of patellofemoral joint stability: force-displacement behavior of the human patella in vitro.

Patellofemoral joint instability is a common clinical problem. However, little quantitative data are available describing the stability characteristics of this joint. We measured the stability of the patella against both lateral and medial displacements across a range of knee flexion angles while the quadriceps were loaded physiologically. For eight fresh-frozen knee specimens a materials testing machine was used to displace the patella 10 mm laterally and 10 mm medially while measuring the required force, with 175 N quadriceps tension. The patella was connected via a ball-bearing patellar mounting 10 mm deep to the anterior surface to allow natural tilt and other rotations. Patellar force-displacement behavior was tested at flexion angles of 0 degrees, 10 degrees, 20 degrees, 30 degrees, 45 degrees, 60 degrees, and 90 degrees. Significant differences were found between the lateral and medial restraining forces at 10 mm displacement. For lateral displacement, the restraining force was least at 20 degrees of knee flexion (74 N at 10 mm displacement), rising to 125 N at 0 degrees and 90 degrees of knee flexion. The restraining force increased progressively with knee flexion for medial patellar displacement, from 147 N at 0 degrees to 238 N at 90 degrees. With quadriceps tension, the patella was more resistant to medial than lateral displacement. Our finding that lateral patellar displacement occurred at the lowest restraining force when the knee was flexed 20 degrees agrees with clinical experience of patellar instability.

The mechanical properties of the two bundles of the human posterior cruciate ligament.

Successful reconstruction of ligaments requires knowledge of the properties of the intact ligament. This study examined the strength of the human posterior cruciate ligament (PCL), treating it as two separate fibre bundles. It was hypothesized (i) that the mechanical and material properties of the anterolateral (aPC) and the posteromedial (pPC) bundles of the PCL were significantly different and (ii) that previous studies have underestimated the strength of the whole PCL. The properties of the two bundles were measured in 10 donors (53-98 yr). The mechanical and material properties of the two bundles were found to be significantly different, the aPC was six times as strong as the pPC. The aPC had a mean strength of 1.6 kN. Allowing for age effects this study suggests that the strength of the PCL in young active people is 4 kN, which is higher than that suggested by previous studies. Because of the difference in the strengths of the two bundles, we conclude that the aPC is primarily responsible for the stabilising effect of the PCL. We therefore recommend that PCL reconstructions should be centered on the middle of the aPC bundle.