The Renaissance of Poly(3-hexylthiophene) as a Promising Hole-Transporting Material Toward Efficient and Stable Perovskite Solar Cells.

To push the commercialization of the promising photovoltaic technique of perovskite solar cells (PSCs), the three-element golden law of efficiency, stability, and cost should be followed. As the key component of PSCs, hole-transporting materials (HTMs) involving widely-used organic semiconductors such as 2,2',7,7'-tetrakis-(N,N-di-4-methoxyphenylamino)-9,9'-spirobifluorene (Spiro-OMeTAD) or poly(triarylamine) (PTAA) usually suffer high-cost preparation and low operational stability. Fortunately, the studies on the classical p-type polymer poly(3-hexylthiophene) (P3HT) as an alternative HTM have recently sparked a broad interest due to its low-cost synthesis, excellent batch-to-batch purity, superior hole conductivity as well as controllable and stable film morphology. Despite this, the device efficiency still lags behind P3HT-based PSCs mainly owing to the mismatched energy level and poor interfacial contact between P3HT and the perovskite layer. Hence, in this review, the study timely summarizes the developed strategies for overcoming the corresponding issues such as interface engineering, morphology regulation, and formation of composite HTMs from which some critical clues can be extracted to provide guidance for further boosting the efficiency and stability of P3HT-based devices. Finally, in the outlook, the future research directions either from the viewpoint of material design or device engineering are outlined.

Surface Re-Engineering of Perovskites with Buckybowls to Boost the Inverted-Type Photovoltaics.

Despite their multifaceted advantages, inverted perovskite solar cells (PSCs) still suffer from lower power conversion efficiencies (PCEs) than their regular counterparts, which is largely due to recombination energy losses (Eloss) that arise from the chemical, physical, and energy level mismatches, especially at the interfaces between perovskites and fullerene electron transport layers (ETLs). To address this problem, we herein introduce an aminium iodide derivative of a buckybowl (aminocorannulene) that is molecularly layered at the perovskite-ETL interface. Strikingly, besides passivating the PbI2-rich perovskite surface, the aminocorannulene enforces a vertical dipole and enhances the surface n-type character that is more compatible with the ETL, thus boosting the electron extraction and transport dynamics and suppressing interfacial Eloss. As a result, the champion PSC achieves an excellent PCE of over 22%, which is superior compared to that of the control device (∼20%). Furthermore, the device stability is significantly enhanced, owing to a lock-and-key-like grip on the mobile iodides by the buckybowls and the resultant increase of the interfacial ion-migration barrier. This work highlights the potential of buckybowls for the multifunctional surface engineering of perovskite toward high-performance and stable PSCs.

The α2δ Calcium Channel Subunit Accessorily and Independently Affects the Biological Function of Ditylenchus destructor.

The α2δ subunit is a high-voltage activated (HVA) calcium channel (Cav1 and Cav2) auxiliary subunit that increases the density and function of HVA calcium channels in the plasma membrane of mammals. However, its function in plant parasitic nematodes remains unknown. In this study, we cloned the full-length cDNA sequence of the voltage-gated calcium channel (VGCC) α2δ subunit (named DdCavα2δ) in Ditylenchus destructor. We found that DdCavα2δ tends to be expressed in the egg stage, followed by the J3 stage. RNA-DIG in situ hybridization experiments showed that the DdCavα2δ subunit was expressed in the body wall, esophageal gland, uterus, post uterine, and spicules of D. destructor. The in vitro application of RNA interference (RNAi) affected the motility, reproduction, chemotaxis, stylet thrusting, and protein secretion of D. destructor to different degrees by targeting DdCα1D, DdCα1A, and DdCavα2δ in J3 stages, respectively. Based on the results of RNAi experiments, it was hypothesized that L-type VGCC may affect the motility, chemotaxis, and stylet thrusting of D. destructor. Non-L-type VGCC may affect the protein secretion and reproduction of D. destructor. The DdCavα2δ subunit gene also affected the motility, chemotaxis, and reproduction of D. destructor. These findings reveal the independent function of the VGCC α2δ subunit in D. destructor as well as give a theoretical foundation for future research on plant parasitic nematode VGCC.

Co-Silencing of the Voltage-Gated Calcium Channel ß Subunit and High-Voltage Activated α1 Subunit by dsRNA Soaking Resulted in Enhanced Defects in Locomotion, Stylet Thrusting, Chemotaxis, Protein Secretion, and Reproduction in Ditylenchus destructor.

The voltage-gated calcium channel (VGCC) ß subunit (Cavß) protein is a kind of cytosolic auxiliary subunit that plays an important role in regulating the surface expression and gating characteristics of high-voltage-activated (HVA) calcium channels. Ditylenchus destructor is an important plant-parasitic nematode. In the present study, the putative Cavß subunit gene of D. destructor, namely, DdCavß, was subjected to molecular characterization. In situ hybridization assays showed that DdCavß was expressed in all nematode tissues. Transcriptional analyses showed that DdCavß was expressed during each developmental stage of D. destructor, and the highest expression level was recorded in the third-stage juveniles. The crucial role of DdCavß was verified by dsRNA soaking-mediated RNA interference (RNAi). Silencing of DdCavß or HVA Cavα1 alone and co-silencing of the DdCavß and HVA Cavα1 genes resulted in defective locomotion, stylet thrusting, chemotaxis, protein secretion and reproduction in D. destructor. Co-silencing of the HVA Cavα1 and Cavß subunits showed stronger interference effects than single-gene silencing. This study provides insights for further study of VGCCs in plant-parasitic nematodes.

Beyond Planar Structure: Curved π-Conjugated Molecules for High-Performing and Stable Perovskite Solar Cells.

Perovskite solar cell (PSC) shows a great potential to become the next-generation photovoltaic technology, which has stimulated researchers to engineer materials and to innovate device architectures for promoting device performance and stability. As the power conversion efficiency (PCE) keeps advancing, the importance of exploring multifunctional materials for the PSCs has been increasingly recognized. Considerable attention has been directed to the design and synthesis of novel organic π-conjugated molecules, particularly the emerging curved ones, which can perform various unmatched functions for PSCs. In this review, the characteristics of three representative such curved π-conjugated molecules (fullerene, corannulene and helicene) and the recent progress concerning the application of these molecules in state-of-the-art PSCs are summarized and discussed holistically. With this discussion, we hope to provide a fresh perspective on the structure-property relation of these unique materials toward high-performance and high-stability PSCs.

Efficient and stable organic solar cells enabled by multicomponent photoactive layer based on one-pot polymerization.

Degradation of the kinetically trapped bulk heterojunction film morphology in organic solar cells (OSCs) remains a grand challenge for their practical application. Herein, we demonstrate highly thermally stable OSCs using multicomponent photoactive layer synthesized via a facile one-pot polymerization, which show the advantages of low synthetic cost and simplified device fabrication. The OSCs based on multicomponent photoactive layer deliver a high power conversion efficiency of 11.8% and exhibit excellent device stability for over 1000 h (>80% of their initial efficiency retention), realizing a balance between device efficiency and operational lifetime for OSCs. In-depth opto-electrical and morphological properties characterizations revealed that the dominant PM6-b-L15 block polymers with backbone entanglement and the small fraction of PM6 and L15 polymers synergistically contribute to the frozen fine-tuned film morphology and maintain well-balanced charge transport under long-time operation. These findings pave the way towards the development of low-cost and long-term stable OSCs.

n-Type Polymer Semiconductors Based on Dithienylpyrazinediimide.

The development of n-type organic semiconductors critically relies on the design and synthesis of highly electron-deficient building blocks with good solubility and small steric hindrance. We report here a strongly electron-deficient dithienylpyrazinediimide (TPDI) and its n-type semiconducting polymers. The pyrazine substitution leads to the resulting polymers with much lower-lying lowest unoccupied molecular orbital (LUMO) levels and improved backbone planarity compared to the reported dithienylbenzodiimide (TBDI)- and fluorinated dithienylbenzodiimide (TFBDI)-based polymer analogues, thus yielding n-type transport character with an electron mobility up to 0.44 cm2 V-1 s-1 in organic thin-film transistors. These results demonstrate that dithienylpyrazinediimide is a highly promising electron-deficient building block for constructing high-performance n-type polymers and the incorporation of pyrazine into imide-functionalized (hetero)arenes is an effective strategy to develop n-type polymers with deep-lying frontier molecular orbital (FMO) levels for organic optoelectronic devices.

Molecular characterization of Ditylenchus destructor voltage-gated calcium channel α1 subunits and analysis of the effect of their knockdown on nematode activity.

Voltage-gated calcium channels (VGCCs) mediate the entry of Ca2+ ions into cells in response to membrane depolarization and play fundamental roles in the nervous system, and the α1 subunits are the main subunits of Ca2+ channels. Caenorhabditis elegans possesses genes encoding α1 subunits; however, very few of these genes have been cloned in plant-parasitic nematodes (PPNs). Ditylenchus destructor is a PPN that has been proposed as a new model for studying the biology and control of PPNs. To understand the structure and function of the VGCCs of this PPN, we first cloned and identified three full-length cDNAs of VGCC α1 subunit genes in D. destructor with the defining structural and conserved features of Cav1 (L-type), Cav2 (non-L-type) and Cav3 (T-type). In situ hybridization assays demonstrated that the Cav1 VGCC α1 subunit gene (DdCα1D) was expressed within body wall muscles. The Cav2 VGCC α1 subunit (DdCα1A) was expressed in the oesophageal gland, vulva and vas deferens of the worm, and the Cav3 VGCC α1 subunit (DdCα1G) was localized to the oesophagus and median bulb. In addition, on the basis of the in vitro knockdown of L-, non-L- and T-type genes via RNAi, these genes were predicted to play a key role in the modulation of locomotion, feeding and reproduction. After the silencing of DdCα1G, the median bulb muscle of D. destructor was obviously contracted, and its feeding and reproduction abilities were significantly inhibited. This study provides insight into the structure and function of VGCC α1 subunits in D. destructor.

Effect of diverting stoma for rectovaginal fistula: A protocol of systematic review and meta-analysis.

BACKGROUND: Rectovaginal fistula (RVF) is a pathologic channel between the anterior wall of the rectum and the posterior wall of the vagina, is rare, and the majority is of traumatic origin. The most common causes are obstetric trauma, local infection, rectal surgery or caused by chronic inflammatory bowel disease. Once the disease will seriously affect the patient's quality of life, and generally not self-healing, most require surgical intervention. At present, diverting stoma is mainly used in patients with severe RVF or complicated RVF or patients with Crohn disease. Due to the lack of large sample, linical studies, its clinical effectiveness is still controversial. The purpose of this systematic review is to evaluate the efficacy of diverting stoma in the treatment of diverting stoma. METHODS: EMBASE, PubMed, the Cochrane Library, Chinese National Knowledge Infrastructure (CNKI), Wanfang Database, Chinese Biomedical Literature Database (CBM), and Chinese VIP Information will be searched systematically by 2 reviewers from the inception until October 2020. The original study that randomized controlled trials (RCTs), clinical controlled trials (CCTs), nonrandomized control trials (NCTs), and retrospective trials (RTs) of diverting stoma for RVF will be selected. In addition, similar searches will be conducted for the reference lists, researches in progress, and the citation lists of identified publications. Study selection, data extraction, and assessment of the quality will be performed independently by 2 reviewers who have been trained prior to data extraction. A meta-analysis will be conduct if the quantity and quality of the original studies included are satisfactory; otherwise, a descriptive analysis will be conducted. Review Manager 5.4 software (The Nordic Cochrane Centre, The Cochrane Collaboration, Copenhagen, Denmark) will be using for data synthesis and assessment the risk of bias according by Cochrane Handbook. RESULT: This study will provide a comprehensive review of current evidence for the treatment of diverting stoma on RVF. CONCLUSION: The conclusion of this study will provide a judging basis that whether the treatment of RVF with diverting stoma is effective. INPLASY REGISTRATION NUMBER: INPLASY2020090070.

Human leptin protein activates the growth of HepG2 cells by inhibiting PERK­mediated ER stress and apoptosis.

Current treatment modalities for various types of hepatic cancer, which has an increasing incidence rate, are inadequate and novel therapies are required. Therefore, identifying targets for liver cancer is becoming increasingly valuable to develop novel methods for therapy. The aim of the present study was to examine the growth activation mechanism of the leptin protein in the liver cancer cell line HepG2. The effects of the leptin protein on cell death were investigated by 2,3-bis-(2-methoxy-4-nitro-5-sulfophenyl)-2H-tetrazolium-5-carboxanilide analysis. DNA fragmentation and terminal deoxynucleotidyl transferase dUTP nick end labeling analysis were also performed to detect cell apoptosis. The expression of leptin and three endoplasmic reticulum (ER) stress unfolded protein response (UPR) proteins, including activating transcription factor 6, phosphorylated­PKR­like ER kinase (p­PERK) and inositol requiring protein 1, were investigated for the examination of ER stress. The mRNA UPR proteins were also detected by reverse transcription polymerase chain reaction. The apoptosis­associated caspase 12 and C/EBP homologous protein (CHOP) was detected by western blot analysis. The expression of or incubation with the leptin protein was able to activate cell growth and inhibit cell death and apoptosis. In cells that expressed leptin or were incubated with leptin protein (pep-LPT), cisplatin­induced ER stress­associated mRNA transcription and protein activation were inhibited. Levels of the ER stress UPR pathway protein, PERK, increased significantly in leptin­silenced cells when treated with cisplatin as compared with those in the leptin­expressing or pep-LPT cells. Furthermore, caspase 12 activation was inhibited in ex­LPT, pep­LPT and HepG2 cells. In conclusion, human leptin protein is involved in promoting the proliferation of HepG2 cells through inhibiting the ER stress­associated apoptotic pathway. The PERK UPR pathway and the apoptotic factor caspase 12 were found to be involved in the inhibition of apoptosis and enhancement of proliferation.