Highly Conductive PDMS Composite Mechanically Enhanced with 3D-Graphene Network for High-Performance EMI Shielding Application.

A highly conductive three-dimensional (3D) graphene network (GN) was fabricated by chemical vapor deposition on a 3D nickel fiber network and subsequent etching process. Then a lightweight and flexible polydimethylsiloxane (PDMS)/GN composite was prepared by a vacuum infiltration method by using the graphene network as a template. The composite showed the superior electrical conductivity of 6100 S/m even at a very low loading level of graphene (1.2 wt %). As a result, an outstanding electromagnetic interference (EMI) shielding effectiveness (SE) of around 40 and 90 dB can be achieved in the X-band at thicknesses of 0.25 and 0.75 mm, respectively, which are much higher than most of the conductive polymers filled with carbon. The 3D graphene network can also act as a mechanical enhancer for PDMS. With a loading level of 1.2 wt %, the composite shows a significant increase by 256% in tensile strength.

Heterostructured NiO/ZnO Nanorod Arrays with Significantly Enhanced H2S Sensing Performance.

H2S gas sensors were fabricated using p-n heterojunctions of NiO/ZnO, in which the ZnO nanorod arrays were wrapped with NiO nanosheets via a hydrothermal synthesis method. When the H2S gas molecules were adsorbed and then oxidized on the ZnO surfaces, the free electrons were released. The increase in the electron concentration on the ZnO boosts the transport speed of the electrons on both sides of the NiO/ZnO p-n junction, which significantly improved the sensing performance and selectivity for H2S detection, if compared with sensors using the pure ZnO nanorod arrays. The response to 20 ppm of H2S was 21.3 at 160 °C for the heterostructured NiO/ZnO sensor, and the limit of detection was 0.1 ppm. We found that when the sensor was exposed to H2S at an operating temperature below 160 °C, the resistance of the sensor significantly decreased, indicating its n-type semiconductor nature, whereas when the operating temperature was above 160 °C, the resistance significantly increased, indicating its p-type semiconductor nature. The sensing mechanism of the NiO/ZnO heterostructured H2S gas sensor was discussed in detail.

NH3-Sensing Mechanism Using Surface Acoustic Wave Sensor with AlO(OH) Film.

In this study, AlO(OH) (boehmite) film was deposited onto a surface acoustic wave (SAW) resonator using a combined sol-gel and spin-coating technology, and prepared and used as a sensitive layer for a high-performance ammonia sensor. The prepared AlO(OH) film has a mesoporous structure and a good affinity to NH3 (ammonia gas) molecules, and thus can selectively adsorb and react with NH3. When exposed to ammonia gases, the SAW sensor shows an initial positive response of the frequency shift, and then a slight decrease of the frequency responses. The sensing mechanism of the NH3 sensor is based on the competition between mass-loading and elastic-loading effects. The sensor operated at room temperature shows a positive response of 1540 Hz to 10 ppm NH3, with excellent sensitivity, selectivity and stability.

Bi-Metal Phosphide NiCoP: An Enhanced Catalyst for the Reduction of 4-Nitrophenol.

Porous phosphide NixCoyP composite nanomaterials are successfully synthesized at different Ni/Co ratios (=0, 0.5, 1, and 2) to reduce 4-nitrophenol. The X-ray diffraction and X-ray photoelectron spectroscopy results demonstrate that the products are CoP, NiCoP/CoP, NiCoP, and NiCoP/Ni2P when the Ni/Co ratio is 0, 0.5, 1, and 2, respectively. The products exhibit different catalytic performance for reduction of 4-nitrophenol at room temperature. Among them, the pure NiCoP delivers a better catalytic efficiency with k app = 677.4 × 10 - 2   min - 1 and k = 338.7   ( Lg - 1 min - 1 ) , due to the synergy between Ni and Co atoms. The sequence of catalytic efficiency of different samples is CoP < NiCoP/CoP < NiCoP/Ni2P < NiCoP.

A fast response & recovery H2S gas sensor based on α-Fe2O3 nanoparticles with ppb level detection limit.

H2S gas sensor based on α-Fe2O3 nanoparticles was fabricated by post-thermal annealing of Fe3O4 precursor which was synthesized using a facile hydrothermal route. The characteristic techniques including X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were adopted to characterize the chemical composition and microstructure of the obtained samples. Gas-sensing performance of the sensor was investigated at different operation temperatures from 100°C to 400°C. Results showed that the sensor exhibited the best sensitivity, reproducibility and long-term stability for detecting H2S gas at an operating temperature of 300°C. The detection limit towards H2S gas was 0.05 ppm, and the response time and recovery time was 30s and 5s, respectively. In addition, sensing mechanism of the sensor towards H2S was discussed.

Surface acoustic wave ammonia sensor based on ZnO/SiO2 composite film.

A surface acoustic wave (SAW) resonator with ZnO/SiO2 (ZS) composite film was used as an ammonia sensor in this study. ZS composite films were deposited on the surface of SAW devices using the sol-gel method, and were characterized using SEM, AFM, and XRD. The performance of the sensors under ammonia gas was optimized by adjusting the molar ratio of ZnO:SiO2 to 1:1, 1:2 and 1:3, and the sensor with the ratio of ZnO to SiO2 equaling to 1:2 was found to have the best performance. The response of sensor was 1.132 kHz under 10 ppm NH3, which was much higher than that of the sensor based on a pristine ZnO film. Moreover, the sensor has good selectivity, reversibility and stability at room temperature. These can be attributed to the enhanced absorption of ammonia and unique surface reaction on composite films due to the existence of silica.