Understanding methanol dissociative adsorption and oxidation on amorphous oxide films.

Interactions between a transition metal (oxide) catalyst and a support can tailor the number and nature of active sites, for instance in the methanol oxidation reaction. We here use ambient pressure X-ray photoelectron spectroscopy (AP-XPS) to identify and compare the surface adsorbates that form on amorphous metal oxide films that maximize such interactions. Considering Al(1-x)MxOy (M = Fe or Mn) films at a range of methanol : oxygen gas ratios and temperatures, we find that the redox-active transition metal site (characterized by methoxy formation) dominates dissociative methanol adsorption, while basic oxygen sites (characterized by carbonate formation) play a lesser role. Product detection, however, indicates complete oxidation to carbon dioxide and water with partial oxidation products (dimethyl ether) comprising a minor species. Comparing the intensity of methoxy and hydroxyl features at a fixed XPS chemical shift suggests methanol deprotonation during adsorption in oxygen rich conditions for high transition metal content. However, increasing methanol partial pressure and lower metal site density may promote oxygen vacancy formation and the dehydroxylation pathway, supported by a nominal reduction in the oxidation state of iron sites. These findings illustrate that AP-XPS and mass spectrometry together are powerful tools in understanding metal-support interactions, quantifying and probing the nature of catalytic active sites, and considering the link between electronic structure of materials and their catalytic activity.

Kinetic Isotope Effect as a Tool To Investigate the Oxygen Reduction Reaction on Pt-based Electrocatalysts - Part II: Effect of Platinum Dispersion.

We investigated the oxygen reduction reaction (ORR) mechanism on Pt nanoparticles (NPs) dispersed on several carbon blacks with various physicochemical properties (i. e. specific surface ranging from 80 to 900 m2 g-1 , different graphitization degree, etc.). Using the kinetic isotope effect (KIE) along with various electrochemical characterizations, we determined that the rate determining step (RDS) of the ORR is a proton-independent step when the density of Pt NPs on the surface of the carbon support is high. Upon decrease of the density of Pt NPs on the surface, the RDS of the ORR starts involving a proton, as denoted by an increase of the KIE >1. This underlined the critical role played by the carbon support in the oxygen reduction reaction electrocatalysis by Pt supported on high surface area carbon.

Versailles Project on Advanced Materials and Standards interlaboratory study on intensity calibration for x-ray photoelectron spectroscopy instruments using low-density polyethylene.

We report the results of a Versailles Project on Advanced Materials and Standards interlaboratory study on the intensity scale calibration of x-ray photoelectron spectrometers using low-density polyethylene (LDPE) as an alternative material to gold, silver, and copper. An improved set of LDPE reference spectra, corrected for different instrument geometries using a quartz-monochromated Al Kα x-ray source, was developed using data provided by participants in this study. Using these new reference spectra, a transmission function was calculated for each dataset that participants provided. When compared to a similar calibration procedure using the NPL reference spectra for gold, the LDPE intensity calibration method achieves an absolute offset of ∼3.0% and a systematic deviation of ±6.5% on average across all participants. For spectra recorded at high pass energies (≥90 eV), values of absolute offset and systematic deviation are ∼5.8% and ±5.7%, respectively, whereas for spectra collected at lower pass energies (<90 eV), values of absolute offset and systematic deviation are ∼4.9% and ±8.8%, respectively; low pass energy spectra perform worse than the global average, in terms of systematic deviations, due to diminished count rates and signal-to-noise ratio. Differences in absolute offset are attributed to the surface roughness of the LDPE induced by sample preparation. We further assess the usability of LDPE as a secondary reference material and comment on its performance in the presence of issues such as variable dark noise, x-ray warm up times, inaccuracy at low count rates, and underlying spectrometer problems. In response to participant feedback and the results of the study, we provide an updated LDPE intensity calibration protocol to address the issues highlighted in the interlaboratory study. We also comment on the lack of implementation of a consistent and traceable intensity calibration method across the community of x-ray photoelectron spectroscopy (XPS) users and, therefore, propose a route to achieving this with the assistance of instrument manufacturers, metrology laboratories, and experts leading to an international standard for XPS intensity scale calibration.

Intrinsically fluorescent gold nanoclusters stabilized within a copper storage protein that follow the Irving-Williams trend in metal ion sensing.

Creating new environmentally friendly and non-toxic biomaterials with novel properties is required for numerous applications in healthcare and sensing. Protein bound gold nanoclusters constitute one such class of materials that offer promise in fluorescence imaging and sensing applications. However, unlike alkane thiol-protected gold nanoclusters, the number of protein-templated gold nanoclusters with such properties is limited and there is a need to expand the repertoire of such attractive hybrid quantum clusters. Herein, we report the synthesis, characterization, and applications of new fluorescent gold nanoclusters with tunable emission properties including blue, orange, and red, within a four-helix bundle copper storage protein (Csp1). The template protein consists of 13 cysteines along the length of the helix, which are suitable ligands to template Au and stabilize the resulting 14-19 atom clusters within the protein. The resulting clusters were extensively characterized by employing spectroscopic, microscopic and other analytical methods. The optical emission, relative quantum yields, and the excited state lifetime of the clusters are shown to depend on synthetic conditions. The clusters were found to be sensitive to the ppm level of transition metal ions with the quenching capabilities following the Irving-Williams series of metals (Co2+ < Ni2+ < Cu2+), which is rationalized based on the relative affinities of transition metals for a given set of ligands. The clusters were also found to be stable across the pH range 4-8.5 which, along with tunable emission properties paves the path for live bio-imaging and bio-sensing applications under physiological conditions.

Organic Functional Group Chemistry in Mineralized Deposits Containing U(IV) and U(VI) from the Jackpile Mine in New Mexico.

We investigated the functional group chemistry of natural organic matter (NOM) associated with both U(IV) and U(VI) in solids from mineralized deposits exposed to oxidizing conditions from the Jackpile Mine, Laguna Pueblo, NM. The uranium (U) content in unreacted samples was 0.44-2.6% by weight determined by X-ray fluorescence. In spite of prolonged exposure to ambient oxidizing conditions, ≈49% of U(IV) and ≈51% of U(VI) were identified on U LIII edge extended X-ray absorption fine structure spectra. Loss on ignition and thermogravimetric analyses identified from 13% to 44% of NOM in the samples. Carbonyl, phenolic, and carboxylic functional groups in the unreacted samples were identified by fitting of high-resolution X-ray photoelectron spectroscopy (XPS) C 1s and O 1s spectra. Peaks corresponding to phenolic and carbonyl functional groups had intensities higher than those corresponding to carboxylic groups in samples from the supernatant from batch extractions conducted at pH 13, 7, and 2. U(IV) and U(VI) species were detected in the supernatant after batch extractions conducted under oxidizing conditions by fitting of high-resolution XPS U 4f spectra. The outcomes from this study highlight the importance of the influence of pH on the organic functional group chemistry and U speciation in mineralized deposits.

Effect of Bicarbonate and Oxidizing Conditions on U(IV) and U(VI) Reactivity in Mineralized Deposits of New Mexico.

We investigated the effect of bicarbonate and oxidizing agents on uranium (U) reactivity and subsequent dissolution of U(IV) and U(VI) mineral phases in the mineralized deposits from Jackpile mine, Laguna Pueblo, New Mexico, by integrating laboratory experiments with spectroscopy, microscopy and diffraction techniques. Uranium concentration in solid samples from mineralized deposit obtained for this study exceeded 7000 mg kg-1, as determined by X-ray fluorescence (XRF). Results from X-ray photoelectron spectroscopy (XPS) suggest the coexistence of U(VI) and U(IV) at a ratio of 19:1 at the near surface region of unreacted solid samples. Analyses made using X-ray diffraction (XRD) and electron microprobe detected the presence of coffinite (USiO4) and uranium-phosphorous-potassium (U-P-K) mineral phases. Imaging, mapping and spectroscopy results from scanning transmission electron microscopy (STEM) indicate that the U-P-K phases were encapsulated by carbon. Despite exposing the solid samples to strong oxidizing conditions, the highest aqueous U concentrations were measured from samples reacted with 100% air saturated 10 mM NaHCO3 solution, at pH 7.5. Analyses using X-ray absorption spectroscopy (XAS) indicate that all the U(IV) in these solid samples were oxidized to U(VI) after reaction with dissolved oxygen and hypochlorite (OCl-) in the presence of bicarbonate (HCO3 -). The reaction between these organic rich deposits, and 100% air saturated bicarbonate solution (containing dissolved oxygen), can result in considerable mobilization of U in water, which has relevance to the U concentrations observed at the Rio Paguate across the Jackpile mine. Results from this investigation provide insights on the reactivity of carbon encapsulated U-phases under mild and strong oxidizing conditions that have important implication in U recovery, remediation and risk exposure assessment of sites.

Reactivity of As and U co-occurring in Mine Wastes in northeastern Arizona.

The reactivity of co-occurring arsenic (As) and uranium (U) in mine wastes was investigated using batch reactors, microscopy, spectroscopy, and aqueous chemistry. Analyses of field samples collected in proximity to mine wastes in northeastern Arizona confirm the presence of As and U in soils and surrounding waters, as reported in a previous study from our research group. In this study, we measured As (< 0.500 to 7.77 µg/L) and U (0.950 to 165 µg/L) in waters, as well as mine wastes (< 20.0 to 40.0 mg/kg As and < 60.0 to 110 mg/kg U) and background solids (< 20.0 mg/kg As and < 60.0 mg/kg U). Analysis with X-ray fluorescence (XRF) and electron microprobe show the co-occurrence of As and U with iron (Fe) and vanadium (V). These field conditions served as a foundation for additional laboratory experiments to assess the reactivity of metals in these mine wastes. Results from laboratory experiments indicate that labile and exchangeable As(V) was released to solution when solids were sequentially reacted with water and magnesium chloride (MgCl2), while limited U was released to solution with the same reactants. The predominance of As(V) in mine waste solids was confirmed by X-ray absorption near edge (XANES) analysis. Both As and U were released to solution after reaction of solids in batch experiments with HCO3 -. Both X-ray photoelectron spectroscopy (XPS) and XANES analysis determined the predominance of Fe(III) in the solids. Mössbauer spectroscopy detected the presence of nano-crystalline goethite, Fe(II) and Fe(III) in (phyllo)silicates, and an unidentified mineral with parameters consistent with arsenopyrite or jarosite in the mine waste solids. Our results suggest that As and U can be released under environmentally relevant conditions in mine waste, which is applicable to risk and exposure assessment.

Iron-streptomycin derived catalyst for efficient oxygen reduction reaction in ceramic microbial fuel cells operating with urine.

In recent years, the microbial fuel cell (MFC) technology has drawn the attention of the scientific community due to its ability to produce clean energy and treat different types of waste at the same time. Often, expensive catalysts are required to facilitate the oxygen reduction reaction (ORR) and this hinders their large-scale commercialisation. In this work, a novel iron-based catalyst (Fe-STR) synthesised from iron salt and streptomycin as a nitrogen-rich organic precursor was chemically, morphologically and electrochemically studied. The kinetics of Fe-STR with and without being doped with carbon nanotubes (CNT) was initially screened through rotating disk electrode (RDE) analysis. Then, the catalysts were integrated into air-breathing cathodes and placed into ceramic-type MFCs continuously fed with human urine. The half-wave potential showed the following trend Fe-STR > Fe-STR-CNT ≫ AC, indicating better kinetics towards ORR in the case of Fe-STR. In terms of MFC performance, the results showed that cathodes containing Fe-based catalyst outperformed AC-based cathodes after 3 months of operation. The long-term test reported that Fe-STR-based cathodes allow MFCs to reach a stable power output of 104.5 ±â€¯0.0 µW cm-2, 74% higher than AC-based cathodes (60.4 ±â€¯3.9 µW cm-2). To the best of the Authors' knowledge, this power performance is the highest recorded from ceramic-type MFCs fed with human urine.

Practical Guides for X-Ray Photoelectron Spectroscopy (XPS): First Steps in planning, conducting and reporting XPS measurements.

Over the past three decades, the widespread utility and applicability of X-ray photoelectron spectroscopy (XPS) in research and applications has made it the most popular and widely used method of surface analysis. Associated with this increased use has been an increase in the number of new or inexperienced users which has led to erroneous uses and misapplications of the method. This article is the first in a series of guides assembled by a committee of experienced XPS practitioners that are intended to assist inexperienced users by providing information about good practices in the use of XPS. This first guide outlines steps appropriate for determining whether XPS is capable of obtaining the desired information, identifies issues relevant to planning, conducting and reporting an XPS measurement, and identifies sources of practical information for conducting XPS measurements. Many of the topics and questions addressed in this article also apply to other surface-analysis techniques.

Metal Reactivity in Laboratory Burned Wood from a Watershed Affected by Wildfires.

We investigated interfacial processes affecting metal mobility by wood ash under laboratory-controlled conditions using aqueous chemistry, microscopy, and spectroscopy. The Valles Caldera National Preserve in New Mexico experiences catastrophic wildfires of devastating effects. Wood samples of Ponderosa Pine, Colorado Blue Spruce, and Quaking Aspen collected from this site were exposed to temperatures of 60, 350, and 550 °C. The 350 °C Pine ash had the highest content of Cu (4997 ± 262 mg kg-1), Cr (543 ± 124 mg kg-1), and labile dissolved organic carbon (DOC, 11.3 ± 0.28 mg L-1). Sorption experiments were conducted by reacting 350 °C Pine, Spruce, and Aspen ashes separately with 10 µM Cu(II) and Cr(VI) solutions. Up to a 94% decrease in Cu(II) concentration was observed in solution while Cr(VI) concentration showed a limited decrease (up to 13%) after 180 min of reaction. X-ray photoelectron spectroscopy (XPS) analyses detected increased association of Cu(II) on the near surface region of the reacted 350 °C Pine ash from the sorption experiments compared to the unreacted ash. The results suggest that dissolution and sorption processes should be considered to better understand the potential effects of metals transported by wood ash on water quality that have important implications for postfire recovery and response strategies.

Influence of platinum group metal-free catalyst synthesis on microbial fuel cell performance.

Platinum group metal-free (PGM-free) ORR catalysts from the Fe-N-C family were synthesized using sacrificial support method (SSM) technique. Six experimental steps were used during the synthesis: 1) mixing the precursor, the metal salt, and the silica template; 2) first pyrolysis in hydrogen rich atmosphere; 3) ball milling; 4) etching the silica template using harsh acids environment; 5) the second pyrolysis in ammonia rich atmosphere; 6) final ball milling. Three independent batches were fabricated following the same procedure. The effect of each synthetic parameters on the surface chemistry and the electrocatalytic performance in neutral media was studied. Rotating ring disk electrode (RRDE) experiment showed an increase in half wave potential and limiting current after the pyrolysis steps. The additional improvement was observed after etching and performing the second pyrolysis. A similar trend was seen in microbial fuel cells (MFCs), in which the power output increased from 167 ± 2 µW cm-2 to 214 ± 5 µW cm-2. X-ray Photoelectron Spectroscopy (XPS) was used to evaluate surface chemistry of catalysts obtained after each synthetic step. The changes in chemical composition were directly correlated with the improvements in performance. We report outstanding reproducibility in both composition and performance among the three different batches.

Functional interfaces for biomimetic energy harvesting: CNTs-DNA matrix for enzyme assembly.

The development of 3D structures exploring the properties of nano-materials and biological molecules has been shown through the years as an effective path forward for the design of advanced bio-nano architectures for enzymatic fuel cells, photo-bio energy harvesting devices, nano-biosensors and bio-actuators and other bio-nano-interfacial architectures. In this study we demonstrate a scaffold design utilizing carbon nanotubes, deoxyribose nucleic acid (DNA) and a specific DNA binding transcription factor that allows for directed immobilization of a single enzyme. Functionalized carbon nanotubes were covalently bonded to a diazonium salt modified gold surface through carbodiimide chemistry creating a brush-type nanotube alignment. The aligned nanotubes created a highly ordered structure with high surface area that allowed for the attachment of a protein assembly through a designed DNA scaffold. The enzyme immobilization was controlled by a zinc finger (ZNF) protein domain that binds to a specific dsDNA sequence. ZNF 268 was genetically fused to the small laccase (SLAC) from Streptomyces coelicolor, an enzyme belonging to the family of multi-copper oxidases, and used to demonstrate the applicability of the developed approach. Analytical techniques such as X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and enzymatic activity analysis, allowed characterization at each stage of development of the bio-nano architecture. This article is part of a Special Issue entitled Biodesign for Bioenergetics--the design and engineering of electronic transfer cofactors, proteins and protein networks, edited by Ronald L. Koder and J.L. Ross Anderson.

Synthesis, characterization, and photoluminescence of Er2O3-Er2SO2 nanoparticles on reduced graphene oxide.

Thermal reduction of erbium nitrate and S-doped reduced graphene oxide (rGO) mixture resulted in the formation of small (∼3-18 nm sized) Er2O3-Er2SO2 nanoparticles with a high degree of surface coverage on the reduced GO support. The morphology, structure, and the chemical composition of the synthesized nanoparticles have been studied by scanning and transmission electron microscopy, x-ray photoelectron spectroscopy, x-ray diffraction, and by optical spectroscopies. The rGO-supported Er2O3-Er2SO2 nanoparticles (Er2O3-Er2SO2/rGO) demonstrate sufficiently strong light emission (luminescence and upconversion) in the visible and near-infrared range via intra-4f Er3+ optical transitions. The reported synthetic approach demonstrates a novel method for synthesizing Er-containing nanoparticles for sensor applications.

Redox Transformations of As and Se at the Surfaces of Natural and Synthetic Ferric Nontronites: Role of Structural and Adsorbed Fe(II).

Adsorption and redox transformations on clay mineral surfaces are prevalent in surface environments. We examined the redox reactivity of iron Fe(II)/Fe(III) associated with natural and synthetic ferric nontronites. Specifically, we assessed how Fe(II) residing in the octahedral sheets, or Fe(II) adsorbed at the edge sites alters redox activity of nontronites. To probe the redox activity we used arsenic (As) and selenium (Se). Activation of both synthetic and natural ferric nontronites was observed following the introduction of Fe(II) into predominantly-Fe(III) octahedral sheets or through the adsorption of Fe(II) onto the mineral surface. The oxidation of As(III) to As(V) was observed via catalytic (oxic conditions) and, to a lesser degree, via direct (anoxic conditions) pathways. We provide experimental evidence for electron transfer from As(III) to Fe(III) at the natural and synthetic nontronite surfaces, and illustrate that only a fraction of structural Fe(III) is accessible for redox transformations. We show that As adsorbed onto natural and synthetic nontronites forms identical adsorption complexes, namely inner-sphere binuclear bidentate. We show that the formation of an inner-sphere adsorption complex may be a necessary step for the redox transformation via catalytic or direct oxidation pathways.

Air Breathing Cathodes for Microbial Fuel Cell using Mn-, Fe-, Co- and Ni-containing Platinum Group Metal-free Catalysts.

The oxygen reduction reaction (ORR) is one of the major factors that is limiting the overall performance output of microbial fuel cells (MFC). In this study, Platinum Group Metal-free (PGM-free) ORR catalysts based on Fe, Co, Ni, Mn and the same precursor (Aminoantipyrine, AAPyr) were synthesized using identical sacrificial support method (SSM). The catalysts were investigated for their electrochemical performance, and then integrated into an air-breathing cathode to be tested in "clean" environment and in a working microbial fuel cell (MFC). Their performances were also compared to activated carbon (AC) based cathode under similar conditions. Results showed that the addition of Mn, Fe, Co and Ni to AAPyr increased the performances compared to AC. Fe-AAPyr showed the highest open circuit potential (OCP) that was 0.307 ± 0.001 V (vs. Ag/AgCl) and the highest electrocatalytic activity at pH 7.5. On the contrary, AC had an OCP of 0.203 ± 0.002 V (vs. Ag/AgCl) and had the lowest electrochemical activity. In MFC, Fe-AAPyr also had the highest output of 251 ± 2.3 µWcm-2, followed by Co-AAPyr with 196 ± 1.5 µWcm-2, Ni-AAPyr with 171 ± 3.6 µWcm-2, Mn-AAPyr with 160 ± 2.8 µWcm-2 and AC 129 ± 4.2 µWcm-2. The best performing catalyst (Fe-AAPyr) was then tested in MFC with increasing solution conductivity from 12.4 mScm-1 to 63.1 mScm-1. A maximum power density of 482 ± 5 µWcm-2 was obtained with increasing solution conductivity, which is one of the highest values reported in the field.

Thermally Stable and Regenerable Platinum-Tin Clusters for Propane Dehydrogenation Prepared by Atom Trapping on Ceria.

Ceria (CeO2 ) supports are unique in their ability to trap ionic platinum (Pt), providing exceptional stability for isolated single atoms of Pt. The reactivity and stability of single-atom Pt species was explored for the industrially important light alkane dehydrogenation reaction. The single-atom Pt/CeO2 catalysts are stable during propane dehydrogenation, but are not selective for propylene. DFT calculations show strong adsorption of the olefin produced, leading to further unwanted reactions. In contrast, when tin (Sn) is added to CeO2 , the single-atom Pt catalyst undergoes an activation phase where it transforms into Pt-Sn clusters under reaction conditions. Formation of small Pt-Sn clusters allows the catalyst to achieve high selectivity towards propylene because of facile desorption of the product. The CeO2 -supported Pt-Sn clusters are very stable, even during extended reaction at 680 °C. Coke formation is almost completely suppressed by adding water vapor to the feed. Furthermore, upon oxidation the Pt-Sn clusters readily revert to the atomically dispersed species on CeO2 , making Pt-Sn/CeO2 a fully regenerable catalyst.

Spectroscopic Investigation of Interfacial Interaction of Manganese Oxide with Triclosan, Aniline, and Phenol.

We investigated the reaction of manganese oxide [MnOx(s)] with phenol, aniline, and triclosan in batch experiments using X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and aqueous chemistry measurements. Analyses of XPS high-resolution spectra suggest that the Mn(III) content increased 8-10% and the content of Mn(II) increased 12-15% in the surface of reacted MnOx(s) compared to the control, indicating that the oxidation of organic compounds causes the reduction of MnOx(s). Fitting of C 1s XPS spectra suggests an increase in the number of aromatic and aliphatic bonds for MnOx(s) reacted with organic compounds. The presence of 2.7% Cl in the MnOx(s) surface after reaction with triclosan was detected by XPS survey scans, while no Cl was detected in MnOx-phenol, MnOx-aniline, and MnOx-control. Raman spectra confirm the increased intensity of carbon features in MnOx(s) samples that reacted with organic compounds compared to unreacted MnOx(s). These spectroscopy results indicate that phenol, aniline, triclosan, and related byproducts are associated with the surface of MnOx(s)-reacted samples. The results from this research contribute to a better understanding of interactions between MnOx(s) and organic compounds that are relevant to natural and engineered environments.

Post Gold King Mine Spill Investigation of Metal Stability in Water and Sediments of the Animas River Watershed.

We applied spectroscopy, microscopy, diffraction, and aqueous chemistry methods to investigate the persistence of metals in water and sediments from the Animas River 13 days after the Gold King Mine spill (August 5, 2015). The Upper Animas River watershed, located in San Juan Colorado, is heavily mineralized and impacted by acid mine drainage, with low pH water and elevated metal concentrations in sediments (108.4 ± 1.8 mg kg-1 Pb, 32.4 ± 0.5 mg kg-1 Cu, 729.6 ± 5.7 mg kg-1 Zn, and 51 314.6 ± 295.4 mg kg-1 Fe). Phosphate and nitrogen species were detected in water and sediment samples from Farmington, New Mexico, an intensive agricultural area downstream from the Animas River, while metal concentrations were low compared to those observed upstream. Solid-phase analyses of sediments suggest that Pb, Cu, and Zn are associated with metal-bearing jarosite and other minerals (e.g., clays, Fe-(oxy)hydroxides). The solubility of jarosite at near-neutral pH and biogeochemical processes occurring downstream could affect the stability of metal-bearing minerals in river sediments. This study contributes relevant information about the association of metal mixtures in a heavy mineralized semiarid region, providing a foundation to better understand long-term metal release in a public and agricultural water supply.

A Hybrid DNA-Templated Gold Nanocluster For Enhanced Enzymatic Reduction of Oxygen.

We report the synthesis and characterization of a new DNA-templated gold nanocluster (AuNC) of ∼1 nm in diameter and possessing ∼7 Au atoms. When integrated with bilirubin oxidase (BOD) and single walled carbon nanotubes (SWNTs), the AuNC acts as an enhancer of electron transfer (ET) and lowers the overpotential of electrocatalytic oxygen reduction reaction (ORR) by ∼15 mV as compared to the enzyme alone. In addition, the presence of AuNC causes significant enhancements in the electrocatalytic current densities at the electrode. Control experiments show that such enhancement of ORR by the AuNC is specific to nanoclusters and not to plasmonic gold particles. Rotating ring disk electrode (RRDE) measurements confirm 4e(-) reduction of O2 to H2O with minimal production of H2O2, suggesting that the presence of AuNC does not perturb the mechanism of ORR catalyzed by the enzyme. This unique role of the AuNC as enhancer of ET at the enzyme-electrode interface makes it a potential candidate for the development of cathodes in enzymatic fuel cells, which often suffer from poor electronic communication between the electrode surface and the enzyme active site. Finally, the AuNC displays phosphorescence with large Stokes shift and microsecond lifetime.