Optical detection of the ultrasound-induced pulsed thermal lens close to the ice-water phase transition.

Piezo-optic and thermo-optic coefficients are important material properties that play a critical role in the design and optimization of many optical devices. The ability to accurately measure and control these coefficients is essential for achieving high performance and reliability in a wide range of applications. In this article, we use the optical detection of the ultrasound-induced thermal lens effect to investigate these properties for water at low temperatures. The results show that the anomalous behavior of water around 4°C is easily observed. The thermal lens method is used to determine the temperature dependence of the piezo-optic and thermo-optic coefficients.

Laser induced thermoelastic surface displacement in solids detected simultaneously by photothermal mirror and interferometry.

We propose a combined pump-probe optical method to investigate heat diffusion properties of solids. We demonstrate single-shot simultaneous laser-induced thermoelastic surface displacement of metals detected by concurrent measurements using photothermal mirror and interferometry. Both methods probe the surface displacement by analyzing the wavefront distortions of the probe beams reflected from the surface of the sample. Thermoelastic properties are retrieved by transient analysis in combination with numerical description of the thermoelastic displacement and temperature rise in the sample and in the surrounding air. This technique presents a capability for material characterization that can be extended to experiments for quantitative surface mapping.

Modeling population and thermal lenses in the presence of Auger Upconversion for Nd(3+) doped materials.

We present a theoretical model to thermal (TL) and population (PL) lenses effects in the presence of Auger upconversion (AU) for analysis of Nd(3+) doped materials. The model distinguishes and quantifies the contributions from TL and PL. From the experimental and theoretical results, the AU cannot be neglected because it plays an important role on the excited state population and therefore on the temperature and polarizability difference between excited and ground states. Considering the extensive use of these techniques, the model presented here could be useful for the investigation of materials and also to avoid misleading analysis of lenses transients.

Discriminating the role of sample length in thermal lensing of solids.

Thermal lens (TL) is a key effect in laser engineering and photothermal spectroscopy. The amplitude of the TL signal or its dioptric power is proportional to the optical path difference (OPD) between the center and border of the beam, which is proportional to the heat power (Ph). Due to thermally induced mechanical stress and bulging of end faces of the sample, OPD depends critically on the geometry of the sample. In this investigation, TL measurements were performed as a function of the sample length keeping the same Ph. It is experimentally demonstrated that for materials with positive ∂n/∂T OPD increases typically 30 to 50% with the decrease of sample length (from long rod to thin-disk geometry). For materials with negative ∂n/∂T, this variation is much larger due to the cancelation of the different contributions to OPD with opposite signs. Furthermore, the experimental investigation presented here validates a recently proposed unified theoretical description of the TL effect.

Role of photophysics processes in thermal lens spectroscopy of fluids: a theoretical study.

Photophysics processes are ubiquitous in nature and difficult to be quantitatively characterized by conventional spectroscopy. Alternatively, pump-probe methods have been widely applied to study these complex processes. In this context, the thermal lens technique is a precise spectroscopic tool for material characterization and presents a wide range of applications in chemical analysis. Here, we present an all numerical approach to analyze the dynamics of photophysics processes and to identify the role of individual contributions of photoreaction and mass diffusion in the thermal lens experiments. The results are essential for a proper understanding of the dominant physical mechanisms in laser-induced photodegradation, which allow precise data analysis of the effects in photosensitive fluids.

Pulsed photothermal mirror technique: characterization of opaque materials.

The time-resolved thermal mirror technique is developed under pulsed laser excitation for quantitative measurement of thermal and mechanical properties of opaque materials. Heat diffusion and thermoelastic equations are solved analytically for pulsed excitation assuming surface absorption and an instantaneous pulse. Analytical results for the temperature change and surface displacement in the sample are compared to all-numerical solutions using finite element method analysis accounting for the laser pulse width and sample geometry. Experiments are performed that validate the theoretical model and regression fitting is performed to obtain the thermal diffusivity and the linear thermal expansion coefficient of the samples. The values obtained for these properties are in agreement with literature data. The technique is shown to be useful for quantitative determinations of the physics properties of metals with high thermal diffusivity.

Towards a comprehensive characterization of spatio-temporal dependence of light-induced electromagnetic forces in dielectric liquids.

The interaction of localized light with matter generates optical electrostriction within dielectric fluids, leading to a discernible change in the refractive index of the medium according to the excitation's light profile. This optical force holds critical significance in optical manipulation and plays a fundamental role in numerous photonic applications. In this study, we demonstrate the applicability of the pump-probe, photo-induced lensing (PIL) method to investigate optical electrostriction in various dielectric liquids. Notably, the thermal and nonlinear effects are observed to be temporally decoupled from the electrostriction effects, facilitating isolated observation of the latter. Our findings provide a comprehensive explanation of optical forces in the context of the recently introduced microscopic Ampère electromagnetic formalism, which is grounded in the dipolar approximation of electromagnetic sources within matter and characterizes electrostriction as an electromagnetic-induced stress within the medium. Here, the optical force density is re-obtained through a new Lagrangian approach.

Modeling the population lens effect in thermal lens spectrometry.

We report a theoretical model and experimental results for laser-induced lensing in solids. The model distinguishes and quantifies the contributions from population and thermal effects. Laser-induced lensing in ytterbium-doped fluorozirconate glass ZBLAN:Yb(3+) is measured, and the thermal and optical properties obtained from analyzing the data with the proposed model agree well with published values. Photothermal techniques are used extensively for the investigation of laser and laser-cooling materials, and the model developed here enables the interpretation of convoluted laser-induced lensing signals that have contributions from different sources.

Resonant excited state absorption and relaxation mechanisms in Tb3+-doped calcium aluminosilicate glasses: an investigation by thermal mirror spectroscopy.

Resonant excited state absorption (ESA) and relaxation processes in Tb(3+)-doped aluminosilicate glasses are quantitatively evaluated. A model describing the excitation steps and upconversion emission is developed and applied to interpret the results from laser-induced surface deformation using thermal mirror spectroscopy. The fluorescence quantum efficiency of level (5)D(4) was found to be close to unity and concentration independent while, for the level (5)D(3), it decreases with Tb(3+) concentration. Emission spectroscopy measurements supported these results. ESA cross sections are found to be more than three orders of magnitude higher than the ground state absorption cross section.

The role of electrostriction in the generation of acoustic waves by optical forces in water.

We present semi-analytical solutions describing the spatiotemporal distributions of temperature and pressure inside low-absorbing dielectrics excited by tightly focused laser beams. These solutions are compared to measurements in water associated with variations of the local refractive index due to acoustic waves generated by electrostriction, heat deposition, and the Kerr effect at different temperatures. The experimental results exhibited an excellent agreement with the modeling predictions, with electrostriction being the dominant transient effect in the acoustic wave generation. Measurements at 4 . 0 ∘ C show that the thermoelastic contribution to the optical signal is significantly reduced due to the low thermal expansion coefficient of water at this temperature.

Tunable color temperature of Ce3+/Eu2+, 3+ co-doped low silica aluminosilicate glasses for white lighting.

In this paper we report results of tunable lighting in Ce(3+)/Eu(2+,3+) doped low silica calcium aluminosilicate glass. Optical spectroscopy experiments indicate that there is a red color compensation from Eu(2+) and Eu(3+) to the green emission from Ce(3+), resulting in a broad and tunable emission spectra depending on the excitation wavelength. This result analysed in the CIE 1976 color diagram shows a close distance from the Plank emission and a correlated color temperature, varying from 5200 to 3500K. This indicates that our system can be easily excited by GaN based blue LEDs, being an interesting phosphor for white lighting devices.

Photoacoustic for thermal diffusivity determination of fish scale: A methodology for environmental integrity monitoring.

In this work the thermal diffusivity (D) of Astyanax lacustris fish scale is investigated aiming to use it for environmental integrity certification. The D values were obtained by a relatively simple procedure by a photoacoustic method. The chosen fish species is from wide occurrence in Brasil's basins. It has short migration, and it has also been used as environmental bioindicator. The results obtained in 195 scales sampled from three different streams in the Midwest region in Brazil gives an average value of D ~ 4 × 10-3 cm2/s. ANCOVA analysis demonstrated that D values are able to differentiate among the three basins and indicates that it is dependent on the scales thickness and water conductivity. This last one is strongly affected by biotic and abiotic actions, so that D values measured by photoacoustic method can be used for interpreting the environmental integrity from where the fishes were sampled.

Unveiling bulk and surface radiation forces in a dielectric liquid.

Precise control over light-matter interactions is critical for many optical manipulation and material characterization methodologies, further playing a paramount role in a host of nanotechnology applications. Nonetheless, the fundamental aspects of interactions between electromagnetic fields and matter have yet to be established unequivocally in terms of an electromagnetic momentum density. Here, we use tightly focused pulsed laser beams to detect bulk and boundary optical forces in a dielectric fluid. From the optical convoluted signal, we decouple thermal and nonlinear optical effects from the radiation forces using a theoretical interpretation based on the Microscopic Ampère force density. It is shown, for the first time, that the time-dependent pressure distribution within the fluid chiefly originates from the electrostriction effects. Our results shed light on the contribution of optical forces to the surface displacements observed at the dielectric air-water interfaces, thus shedding light on the long-standing controversy surrounding the basic definition of electromagnetic momentum density in matter.

Ex vivo UV-vis and FTIR photoacoustic spectroscopy of natural nanoemulsions from cellulose nanocrystals and saponins topically applied into the skin: Diffusion rates and physicochemical evaluation.

Nanoemulsions are increasingly gaining importance in the development of topically applied medicine and cosmetic products because their small droplets favor the penetration rates of active compounds into the body. In this scenario, the measurements of their diffusion rates as well as eventual physicochemical changes in the target tissues are of utmost importance. It is also recognized that the use of natural surfactants can avoid allergic reactions as frequently observed for synthetic products. The natural saponins extracted from Sapindus Saponaria have the property of forming foam and are exploited as biocompatible and biodegradable, while cellulose nanocrystals are known to increase the stability of a formulation avoiding the coalescence of drops at the interface. Therefore, nanoemulsions combining natural saponins and cellulose nanocrystals are promising systems that may facilitate greater diffusion rates of molecules into the skin, being candidates to substitute synthetic formulations. This study applied the Photoacoustic Spectroscopy technique to measure the diffusion rates and the physicochemical properties of nanoemulsified formulations containing saponins and cellulose nanocrystals topically applied to the skin. The ex vivo study combined the first-time photoacoustic measurements performed in both ultraviolet-visible and mid-infrared spectral regions. The toxicity of these formulations in L929 cells was also evaluated. The results showed that the formulations were able to propagate throughout the skin to a depth of approximately 756 µm, reaching the dermal side. The non-observation of absorbing band shifting or new bands in the FTIR spectra suggests that there were no structural changes in the skin as well as in the formulations after the nanoemulsions administration. The cytotoxicity results showed that the increase of cellulose nanocrystals concentration decreased cellular toxicity. In conclusion, the results demonstrated the advantage of combining photoacoustic methods in the ultraviolet-visible and mid-infrared spectral regions to analyze drug diffusion and interaction with the skin tissues. Both methods complement each other, allowing the confirmation of the nanoemulsion diffusion through the skin and also suggesting there were no detectable physicochemical changes in the tissues. Formulations stabilized with saponins and cellulose nanocrystals showed great potential for the development of topically administered cosmetics and drugs.

Soret effect and photochemical reaction in liquids with laser-induced local heating.

We report a theoretical model and experimental results for laser-induced local heating in liquids, and propose a method to detect and quantify the contributions of photochemical and Soret effects in several different situations. The time-dependent thermal and mass diffusion equations in the presence and absence of laser excitation are solved. The two effects can produce similar transients for the laser-on refractive index gradient, but very different laser-off behavior. The Soret effect, also called thermal diffusion, and photochemical reaction contributions in photochemically reacting aqueous Cr(VI)-diphenylcarbazide, Eosin Y, and Eosin Y-doped micellar solutions, are decoupled in this work. The extensive use of lasers in various optical techniques suggests that the results may have significance extending from physical-chemical to biological applications.

In Vitro Evaluation of the Stabilization Time of Chemical Bonds During Setting Reaction and Microhardness of Preheated Glass-Ionomer Cements.

OBJECTIVES: To evaluate the effect of preheating glass-ionomer cement (GIC) restorative materials on stabilization time (ST) of their metal carboxylate bonds and on microhardness. METHODS AND MATERIALS: Two conventional high-viscosity GICs, Ketac Universal (3M ESPE) and Equia Forte (GC), were evaluated. The thermographic camera was used to measure the temperature inside the glass-ionomer cement capsules before and after heating. The preheating of capsules was performed at 54°C for 30 seconds in a commercial device. Characterization of ST in the GICs was determined by Fourier Transform Infrared (FTIR) spectroscopy. For this, 10 samples of each material were prepared, five in the non-preheated group (control) and five with preheating. FTIR spectra were obtained 10 minutes after mixing (control group) or after heating and then every 10 minutes for 120 minutes. For the microhardness test, 20 cylindrical specimens (3 mm height x 6 mm diameter) were prepared for each material (10 preheated, 10 control). The microhardness was determined at three time intervals: 10 minutes after mixing, after the ST as detected through the FTIR part of the study, and after one week. Knoop microhardness was assessed using a diamond indenter with a 25 g load and 15 seconds dwell time. RESULTS: Ketac Universal showed an increase in temperatures of 15.7°C for powder and 3.6°C for liquid, while Equia Forte showed 16.4°C for powder and 8.5°C for liquid. FTIR spectra indicated that preheating reduced the ST for Equia Forte but increased it for Ketac Universal. Preheating increased the initial microhardness (T1) of Equia Forte. With maturation over one week, it was observed that preheating significantly improved the microhardness of both materials compared with the control specimens. CONCLUSION: Preheating influenced the ST and the microhardness of Ketac Universal and Equia Forte. The ST and microhardness of Ketac Universal increased after seven days, whereas Equia Forte showed a reduced ST and increased microhardness from the outset.

High values of gain cross section and luminescence quantum efficiency in OH(-)-free Ti3+-doped low-silica calcium aluminosilicate glass.

We recently reported that Ti(3+)-doped low-silica calcium aluminosilicate glass presents long luminescence lifetime (170 micros) and broad emission band (190 nm) shifted toward the visible region when compared with those from Ti(3+):sapphire single crystal and Ti(3+)-doped glasses [Phys. Rev. Lett.100, 027402 (2008)]. Here we demonstrate that this glass also shows high values of both gain cross section (approximately 4.7 x 10(-19) cm(2)) and luminescence quantum efficiency (approximately 70%). By comparing these values with those for Ti(3+):sapphire crystal, we can conclude that the studied Ti(3+)-doped glass is a promising system for tunable solid-state lasers.

Color tunability with temperature and pump intensity in Yb3+/Tm3+ codoped aluminosilicate glass under anti-Stokes excitation.

Pump and thermally induced color tunabilities were demonstrated in Yb(3+)/Tm(3+) codoped low silica calcium aluminosilicate (LSCAS) glass under anti-Stokes excitation at 1.064 microm. The effects of pump intensity and sample's temperature on the upconversion emissions and mainly on the color tunabilities (from 800 to 480 nm) were investigated. The results revealed a 20- and a threefold reductions at 800/480 nm ratio as, respectively, the pump intensity and sample's temperature were increased from 27 to 700 kW/cm(2) and from 296 to 577 K. These behaviors with pump intensity and temperature (a strong increase of the 480 nm emission in comparison with the 800 nm one) were attributed to the several efficient processes occurring in the LSCAS system (Yb(3+)-->Tm(3+) energy-transfer processes, easy saturations of the Yb(3+) and Tm(3+) excited states, and radiative emissions). Besides these assigns, the temperature dependence is mainly assigned to the temperature-dependent effective absorption cross section of the ytterbium sensitizer through the so-called multiphonon-assisted anti-Stokes excitation process. Theoretical analyses and fits of the experimental data provided quantitative information.

Effects of Bioactive Agents on Dentin Mineralization Kinetics After Dentin Bleaching.

OBJECTIVES: This study evaluated effects of Bioglass 45S5 (BG) and Biosilicate (BS) remineralization on the chemical composition and bond strength of control dentin (CD) and bleached dentin (BD) surfaces. METHODS AND MATERIALS: Dentin bleaching treatment was performed using the walking bleaching technique with 0.01 g of sodium perborate and 0.5 mL of 3% hydrogen peroxide for 14 days. Remineralization treatment was carried out by rubbing a remineralization solution (0.015 g of BG or BS diluted in 1.35 mL of distilled water) on the etched dentin surface for 30 seconds. Micro-Raman spectroscopy (MRS) was used to quantitatively analyze the mineral matrix ratios of CD and BD (n=5) after remineralization treatment with BG and BS over 15 days of incubation in artificial saliva. The CD and BD discs (n=10) with and without remineralization treatment with BG and BS were restored using a two-step etch-and-rinse adhesive system (Optibond S, Kerr) and five layers of 1-mm-thick composite resin (Filtek Z250, 3M ESPE). The restored dentin discs were sectioned into nine bonded beams with cross-sectional areas of approximately 0.9 mm2 and tested for microtensile bond strength (µTBS). The dentin surface of one fractured beam per tooth was submitted to MRS to characterize the physicochemical composition (n=10) at the interface. The data were analyzed using one-way analysis of variance and the Tukey-Kramer post hoc test (p<0.005). RESULTS: MRS bioactive analyses revealed that both BG and BS promoted increased mineral matrix ratios in the CD and BD. Significantly higher µTBS values were found after CD treatment with BG (CD: 57 MPa±11; CD-BG: 78 MPa±15) and when BG and BS were applied to the BD (BD: 42 MPa±5; BD-BG: 71 MPa±14; BD-BS: 64 MPa±11) (p<0.005). The MRS analysis of the fractured dentin beam showed that the remineralization treatment significantly increased the dentin relative mineral concentration and promoted the appearance of new interface peaks, indicating a chemical interaction (p<0.005). CONCLUSION: Remineralization of BD is an effective therapy to restore damage caused by dentin bleaching and acid conditioning. This approach not only increases dentin mineral compounds but also improves dentin's ability to interact chemically with the adhesive system.

Thermal lens and interferometric method for glass transition and thermo physical properties measurements in Nd2O3 doped sodium zincborate glass.

In this work the time resolved thermal lens method is combined with interferometric technique, the thermal relaxation calorimetry, photoluminescence and lifetime measurements to determine the thermo physical properties of Nd(2)O(3) doped sodium zincborate glass as a function of temperature up to the glass transition region. Thermal diffusivity, thermal conductivity, fluorescence quantum efficiency, linear thermal expansion coefficient and thermal coefficient of electronic polarizability were determined. In conclusion, the results showed the ability of thermal lens and interferometric methods to perform measurements very close to the phase transition region. These techniques provide absolute values for the measured physical quantities and are advantageous when low scan rates are required.