Real-time in situ dynamic sub-surface imaging of multi-component electrodeposited films using event mode neutron reflectivity.

Exquisite control of the electrodeposition of metal films and coatings is critical to a number of high technology and manufacturing industries, delivering functionality as diverse as anti-corrosion and anti-wear coatings, electronic device interconnects and energy storage. The frequent involvement of more than one metal motivates the capability to control, maintain and monitor spatial disposition of the component metals, whether as multilayers, alloys or composites. Here we investigate the deposition, evolution and dissolution of single and two-component metal layers involving Ag, Cu, and Sn on Au substrates immersed in the deep eutectic solvent (DES) Ethaline. During galvanostatically controlled stripping of the metals from two-component systems the potential signature in simultaneous thickness electrochemical potential (STEP) measurements provides identification of the dissolving metal; coulometric assay of deposition efficiency is an additional outcome. When combined with quartz crystal microbalance (QCM) frequency responses, the mass change : charge ratio provides oxidation state data; this is significant for Cu in the high chloride environment provided by Ethaline. The spatial distribution (solvent penetration and external roughness) of multiple components in bilayer systems is provided by specular neutron reflectivity (NR). Significantly, the use of the recently established event mode capability shortens the observational timescale of the NR measurements by an order of magnitude, permitting dynamic in situ observations on practically useful timescales. Ag,Cu bilayers of both spatial configurations give identical STEP signatures indicating that, despite the extremely low layer porosity, thermodynamic constraints (rather than spatial accessibility) dictate reactivity; thus, surprisingly, Cu dissolves first in both instances. Sn penetrates the Au electrode on the timescale of deposition; this can be prevented by interposing a layer of either Ag or Cu.

Electrochemistry and speciation of Au(+) in a deep eutectic solvent: growth and morphology of galvanic immersion coatings.

In this study we compare the electrochemical and structural properties of three gold salts AuCl, AuCN and KAu(CN)2 in a Deep Eutectic Solvent (DES) electrolyte (Ethaline 200) in order to elucidate factors affecting the galvanic deposition of gold coatings on nickel substrates. A chemically reversible diffusion limited response was observed for AuCl, whereas AuCN and KAu(CN)2 showed much more complicated, kinetically limited responses. Galvanic exchange reactions were performed on nickel substrates from DES solutions of the three gold salts; the AuCN gave a bright gold coating, the KAu(CN)2 solution give a visibly thin coating, whilst the coating from AuCl was dull, friable and poorly adhesive. This behaviour was rationalised by the differing speciation for each of these compounds, as evidenced by EXAFS methods. Analysis of EXAFS data shows that AuCl forms the chlorido-complex [AuCl2](-), AuCN forms a mixed [AuCl(CN)](-) species, whereas KAu(CN)2 maintains its [Au(CN)2](-) structure. The more labile Cl(-) enables easier reduction of Au when compared to the tightly bound cyanide species, hence leading to slower kinetics of deposition and differing electrochemical behaviour. We conclude that metal speciation in DESs is a function of the initial metal salt and that this has a strong influence on the mechanism and rate of growth, as well as on the morphology of the metal deposit obtained. In addition, these coatings are also extremely promising from a technological perspective as Electroless Nickel Immersion Gold (ENIG) finishes in the printed circuit board (PCB) industry, where the elimination of acid in gold plating formulation could potentially lead to more reliable coatings. Consequently, these results are both significant and timely.

Effect of Graphene Oxide and Temperature on Electrochemical Polymerization of Pyrrole and Its Stability Performance in a Novel Eutectic Solvent (Choline Chloride-Phenol) for Supercapacitor Applications.

Polypyrrole (Ppy)-modified graphene oxide (GO) electrodes were synthesized for the first time in a choline chloride-phenol-based deep eutectic solvent at various temperatures via electrochemical methods without the addition of any inorganic or organic catalysts. The surface morphologies and structures of the modified films were assessed via scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, and X-ray diffraction techniques. The electrochemical properties and stability of the modified electrodes were investigated via cyclic voltammetry and impedance spectroscopy at various temperatures and scan rates. The results showed that the specific capacitance of the nanocomposites decreased with increasing scan rate during cycling. Additionally, the specific capacitances of the pure Ppy and Ppy/GO films increased with increasing temperature of the electrolyte (monomer-free), attributed to the reduction in viscosity at elevated temperature. The specific capacitances at 5 mV s-1 were found to be 1071.78 and 594.79 F g-1 for Ppy/GO (20 wt %) at 50 and 25 °C, respectively. It was also observed that the resistance in the cell decreased with increasing electrolyte temperature. Ppy/GO at 50 mV s-1 was found to have the highest capacitance retention of 85% after 2000 cycles, showing better cycling stability than the pure Ppy film. Herein, the incorporation of GO in the Ppy matrix led to improved specific capacitance and cyclic stability, suggesting that Ppy/GO could represent a promising electrode material for supercapacitor applications.

Immiscible electrolyte systems based on asymmetric hydrophobic room temperature ionic liquids.

The effect on the melting point of the introduction of asymmetry in tetraalkylammonium halide salts has been investigated leading to the synthesis of new, hydrophobic (room temperature) ionic liquids suitable for liquid/liquid electrochemistry; one of these, tri(hexyl)decylammonium tetrakis(pentafluorophenyl)borate, displays the largest electrochemical window observed to date for a biphasic room temperature ionic liquid system.

Lead acid battery recycling for the twenty-first century.

There is a growing need to develop novel processes to recover lead from end-of-life lead-acid batteries, due to increasing energy costs of pyrometallurgical lead recovery, the resulting CO2 emissions and the catastrophic health implications of lead exposure from lead-to-air emissions. To address these issues, we are developing an iono-metallurgical process, aiming to displace the pyrometallurgical process that has dominated lead production for millennia. The proposed process involves the dissolution of Pb salts into the deep eutectic solvent (DES) Ethaline 200, a liquid formed when a 1 : 2 molar ratio of choline chloride and ethylene glycol are mixed together. Once dissolved, the Pb can be recovered through electrodeposition and the liquid can then be recycled for further Pb recycling. Firstly, DESs are being used to dissolve the lead compounds (PbCO3, PbO, PbO2 and PbSO4) involved and their solubilities measured by inductively coupled plasma optical emission spectrometry (ICP-OES). The resulting Pb2+ species are then reduced and electrodeposited as elemental lead at the cathode of an electrochemical cell; cyclic voltammetry and chronoamperometry are being used to determine the electrodeposition behaviour and mechanism. The electrodeposited films were characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). We discuss the implications and opportunities of such processes.

Do all ionic liquids need organic cations? Characterisation of [AlCl2·nAmide]+ AlCl4(-) and comparison with imidazolium based systems.

The addition of a simple amide to AlCl(3) causes the formation of a liquid of the form [AlCl(2)·nAmide](+) AlCl(4)(-). The material thus produced is liquid over a wide temperature range, is relatively insensitive to water and has the properties of an ionic liquid. This ionic liquid is shown to be a suitable medium for the acetylation of ferrocene and the electrodeposition of aluminium and demonstrated that quaternary ammonium cations are not always needed to form ionic liquids.