Architecture and design of a robotic mastication simulator for interactive load testing of dental implants and the mandible.

STATEMENT OF PROBLEM: Determination of interactive loading between a dental prosthesis and the host mandible is essential for implant prosthodontics and to preserve bone. PURPOSE: The purpose of this study was to develop and evaluate a robotic mastication simulator to replicate the human mastication force cycle to record the required interactive loading using specifically designed force sensors. MATERIAL AND METHODS: This robotic mastication simulator incorporated a Stewart parallel kinematic mechanism (PKM) controlled in the force-control loop. The hydraulically operated PKM executed the wrench operation, which consisted of the combined effect of forces and moments exhibited by the mastication process. Principal design features of this robotic simulator included PKM kinematic modeling, static force analysis to realize the masticatory wrench characteristics, and the architecture of its hydraulic system. Additionally, the design of a load-sensing element for the mandible and implant interaction was also incorporated. This element facilitated the quantification of the load distribution between implants and the host bone during the masticatory operation produced by the PKM. These loading tests were patient-specific and required separate artificial mandibular models for each patient. RESULTS: The simulation results demonstrated that the robotic PKM could replicate human mastication. These results validated the hydraulic system modeling for the required range of masticatory movements and effective forces of the PKM end-effector. The overall structural design of the robotic mastication simulator presented the integration of the PKM and its hydraulic system with the premeditated load-recording mechanism. CONCLUSIONS: The developed system facilitated the teeth-replacement procedure. The PKM accomplished the execution of mastication cycle involving 6 degrees of freedom, enabling any translation and rotation in sagittal, horizontal, and vertical planes. The mechanism can simulate the human mastication cycle and has a force application range of up to 2000 N. The designed load-sensing element can record interactive forces within the range of 200 N to 2000 N with fast response and high sensitivity to produce a robotic mastication simulator with custom-made modules.

Orthodontic miniscrews: an experimental campaign on primary stability and bone properties.

OBJECTIVE: To evaluate the primary stability of different shaped miniscrews through the acquisition of data regarding maximum insertion torque, pullout force, and a radiodiagnosic evaluation of bone characteristics. MATERIALS AND METHODS: Sixty fresh porcine bone samples were scanned by computed tomography (CT) and cone-beam computed tomography (CBCT). By means of a dedicated software, CT and CBCT images were analysed to measure the insertion-site cortical thickness, cortical density, and marrow bone density. Sixty miniscrews of 12 different types were implanted with no predrilling pilot hole in the bone samples. Every device was tightened by means of a digital torque screwdriver and torque data were collected. Subsequently, pullout tests were performed. Spearman and Pearson correlations were employed to compare any relationship between continuous variables. RESULTS: Different types of miniscrews did not show statistically significant differences in their torque value (P = 0.595), instead a significant difference was revealed by considering their load measures (P = 0.039). Cortical bone thickness resulted strongly correlated both with value of load (P < 0.001), and modestly with torque measures (P = 0.004). A strong positive correlation was found between CT and CBCT both for cortical density (P < 0.001) and marrow bone density (P < 0.001). CONCLUSION: Bone characteristics play the major role in miniscrews primary stability.

Fiber-Reinforced Composites for Full-Arch Implant-Supported Rehabilitations: An In Vitro Study.

Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant-supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber-reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence with the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made of the following different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multidirectional carbon fibers+resin (ICFRC+AR), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+AR), FRC with glass fibers+composite (GFRC+C), and resin (R, fully acrylic prosthesis). Flexural tests were conducted using a Zwick/Roell Z 0.5 machine, and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C and GFRC+C, followed by Ti+R and Au+R. The greatest deformations were observed for resin alone, ICFRC+R, and GFRC+R. The results were slightly different in the incisal region, probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow for predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, although it showed greater deflections. Further studies are needed in order to evaluate how different prosthesis designs and material thicknesses might affect the outcomes.

Tackling Inequalities in Oral Health: Bone Augmentation in Dental Surgery through the 3D Printing of Poly(ε-caprolactone) Combined with 20% Tricalcium Phosphate.

The concept of personalized medicine and overcoming healthcare inequalities have become extremely popular in recent decades. Polymers can support cost reductions, the simplicity of customized printing processes, and possible future wide-scale expansion. Polymers with ß-tricalcium phosphate (TCP) are well known for their synergy with oral tissues and their ability to induce osteoconductivity. However, poor information exists concerning their properties after the printing process and whether they can maintain an unaffected biological role. Poly(ε-caprolactone) (PCL) polymer and PCL compounded with TCP 20% composite were printed with a Prusa Mini-LCD-®3D printer. Samples were sterilised by immersion in a 2% peracetic acid solution. Sample analyses were performed using infrared-spectroscopy and statical mechanical tests. Biocompatibility tests, such as cell adhesion on the substrate, evaluations of the metabolic activity of viable cells on substrates, and F-actin labelling, followed by FilaQuant-Software were performed using a MC3T3-E1 pre-osteoblasts line. PCL+ß-TCP-20% composite is satisfactory for commercial 3D printing and appears suitable to sustain an ISO14937:200937 sterilization procedure. In addition, the proper actin cytoskeleton rearrangement clearly shows their biocompatibility as well as their ability to favour osteoblast adhesion, which is a pivotal condition for cell proliferation and differentiation.

Multipotent Mesenchymal Cells Homing and Differentiation on Poly(ε-caprolactone) Blended with 20% Tricalcium Phosphate and Polylactic Acid Incorporating 10% Hydroxyapatite 3D-Printed Scaffolds via a Commercial Fused Deposition Modeling 3D Device.

As highlighted by the 'Global Burden of Disease Study 2019' conducted by the World Health Organization, ensuring fair access to medical care through affordable and targeted treatments remains crucial for an ethical global healthcare system. Given the escalating demand for advanced and urgently needed solutions in regenerative bone procedures, the critical role of biopolymers emerges as a paramount necessity, offering a groundbreaking avenue to address pressing medical needs and revolutionize the landscape of bone regeneration therapies. Polymers emerge as excellent solutions due to their versatility, making them reliable materials for 3D printing. The development and widespread adoption of this technology would impact production costs and enhance access to related healthcare services. For instance, in dentistry, the use of commercial polymers blended with ß-tricalcium phosphate (TCP) is driven by the need to print a standardized product with osteoconductive features. However, modernization is required to bridge the gap between biomaterial innovation and the ability to print them through commercial printing devices. Here we showed, for the first time, the metabolic behavior and the lineage commitment of bone marrow-derived multipotent mesenchymal cells (MSCs) on the 3D-printed substrates poly(e-caprolactone) combined with 20% tricalcium phosphate (PCL + 20% ß-TCP) and L-polylactic acid (PLLA) combined with 10% hydroxyapatite (PLLA + 10% HA). Although there are limitations in printing additive-enriched polymers with a predictable and short half-life, the tested 3D-printed biomaterials were highly efficient in supporting osteoinductivity. Indeed, considering different temporal sequences, both 3D-printed biomaterials resulted as optimal scaffolds for MSCs' commitment toward mature bone cells. Of interest, PLLA + 10% HA substrates hold the confirmation as the finest material for osteoinduction of MSCs.

Miniscrew design and bone characteristics: an experimental study of primary stability.

INTRODUCTION: The purpose of this study was to evaluate the correlations between bone characteristics, orthodontic miniscrew designs, and primary stability. METHODS: Four different miniscrews were placed in pig ribs. The miniscrews were first scanned with a scanning electron microscope to obtain measurable images of their threads. Subsequently, the maximum insertion torque of the screws and the maximum load value in the pullout force tests were measured; furthermore, bone specimen characteristics were analyzed by using cone-beam computed tomography. For each bone sample, the insertion site cortical thickness as well as both cortical and marrow bone density were evaluated. The nonparametric Kendall rank correlation (tau) was used to evaluate the strength of the associations among the characteristics measured. The nonparametric Kruskall-Wallis test was used to evaluate the differences among the groups, and post-hoc comparisons were assessed by using the Nemenyi-Damico-Wolfe-Dunn test. RESULTS: A significant dependence was found between pitch and maximum insertion torque (tau, -0.49). Positive correlations were also found between pullout force and maximum insertion torque (tau, 0.64), cortical thickness (tau, 0.36), and marrow bone density (tau, 0.35). CONCLUSIONS: In this in-vitro experimental study, strong correlations were observed among miniscrew geometry, bone characteristics, and primary stability.

Immediate Implants in the Aesthetic Zone: Is Socket Shield Technique a Predictable Treatment Option? A Narrative Review.

(1) Background. Dental implant placement in the anterior region requires extreme precision due to relatively high aesthetic demand. This narrative review aimed to analyse some of the available clinical studies of the socket-shield technique and determine its viability for dental implant survival/success and complication rates. (2) Methods. An electronic search for publications was performed using the Cochrane, PubMed-MEDLINE, Web of Science, and Google Scholar databases. All electronic searches included human clinical and animal studies and were performed by three independent examiners. (3) Results. A total of 1383 records were identified with the initial search strategies, but only 25 full texts + five abstracts clinical studies were kept after the recruitment criteria screening. The technical details, advantages, and limitations of the techniques were illustrated. (4) Conclusion. Within the limitations of the present review, it would be merely justified that immediate dental implant placement in conjunction with the socket-shield technique can be a promising strategy for dental implant therapy.

A partial equilibrium theory for liquids bonded to immobile solids.

In order to obtain consistency with the force balance theory of Young and Laplace, which quantitatively predicts the height of capillary rise from the contact angles of drops on solid surfaces, Gibbs made chemical potentials in interface functions of the integral interface free energies. We cite evidence that equilibrium chemical potentials in one-component systems are identical at interfaces to equilibrium chemical potentials in bulk phases. We evaluate two postulates. (1) Partial free energies of liquids at an interface with a solid are functions of the strength and range of attractive fields outside solid phase boundaries. (2) At equilibrium, the chemical potentials in all interfaces of a one-component liquid equal the chemical potential in its interior when the liquid is bonded to one or more immiscible solids. These postulates yield equations for partial equilibrium (PE) states of drops, films, and liquids. The PE equations yield the same prediction of the height of a meniscus from the contact angle of drops as does Young-Laplace theory and also the same dependence of the volume of capillary condensate on vapor pressure as does the Kelvin equation. But our measurements of the contact angles of water on glass and Teflon and between their close-spaced surfaces contradict the YL supposition that meniscus angles are the same as angles of drops on glass and Teflon surfaces and support the PE postulate that attraction by the external fields of solids, not meniscus curvature, is responsible for capillary rise. We use published data to illustrate the validity of the PE conclusion that divergence or convergence at the saturation pressure of a parent liquid depends on whether or not the attractive field of a solid surface imparts to the liquid more than twice the energy required to create two liquid-vapor interfaces. For divergent water films on quartz, the PE equation provides a quantitative fit to experimental data for films of any thickness greater than 1.5 nm. No previous theory has accomplished that. In an appendix, we illustrate applications of PE theory to evaluating the complex interactions between inherently reversible chemical diffusion and inherently irreversible forces introduced by strains.

Mechanical characterisation of multi vs. uni-directional carbon fiber frameworks for dental implant applications.

OBJECTIVES: The aim of the present study was to investigate the mechanical characteristics of dental implant frameworks made of unidirectional carbon fiber composite (UF) and to compare them with those provided by multidirectional carbon fiber composite (IF). METHODS: 8 identical UF samples were used. The samples were initially evaluated by optical microscope and SEM then non-destructive and destructive mechanical tests were performed on 4 samples in order to evaluate dynamic, static elastic modulus, wettability and ultimate strength. The outcomes were compared with those of IF samples tested following the same protocol - data reported in a previous published paper. The remaining 4 samples were aged for 60 days in isotonic saline solution at 37 °C simulating the human saliva. The same tests reported before were performed on the aged samples. RESULTS: The dynamic elastic modulus was lower for UF (78.1 GPa for UF vs. 92.2 GPa for IF) as well as the static elastic modulus (71.0 GPa for UF vs. 84.5 GPa for IF). The ultimate strength value was 582 MPa for the IF samples and 700 MPa for the UF. The aging process of the UF samples did not show any appreciable variation, with small differences that falls within the experimental error. SIGNIFICANCE: Unidirectional carbon fiber-reinforced composite appears suitable for the fabrication of frameworks for implant-supported full-arch dentures. The dynamic elastic modulus was higher for UF while the static elastic modulus was higher for IF. The aging process seems not able to significantly alter the mechanical properties of the material. Further research is needed to evaluate the clinical significance of such outcomes.

Torque efficiency of a customized lingual appliance : Performance of wires with three different ligature systems.

PURPOSE: Torque control in lingual orthodontics is key to obtain optimal esthetic results. The aim of this in vitro experimental study was to verify the efficiency of the ligature-archwire-slot system in torque control using a customized lingual appliance. METHODS: An idealized cast with eight extracted human teeth was created and a set of customized lingual brackets was obtained. Tests were performed with the following wires: 0.016â€³â€¯× 0.022″ nickel-titanium (NiTi), 0.016â€³â€¯× 0.024″ stainless steel (SS), 0.017â€³â€¯× 0.025″ ßIII titanium (ßIIITi), 0.0182â€³â€¯× 0.0182″ ßIIITi, 0.018â€³â€¯× 0.025″ SS, 0.018â€³â€¯× 0.025″ NiTi, 0.018â€³â€¯× 0.025″ ßIIITi, and three types of ligatures were tested using a universal testing machine to calculate the efficiency in torque control. A blind statistical analysis was performed. RESULTS: Based on post hoc multiple comparisons, differences were found for two of the three ligatures when using the 0.016â€³â€¯× 0.022″ NiTi wires (p < 0.001 for both ligatures). When considering all ligatures, 0.018â€³â€¯× 0.025″ SS and 0.018â€³â€¯× 0.025″ ßIIITi were significantly different from all other wires (p < 0.001 in all cases). With a moment of 5 Nmm, the 0.016â€³â€¯× 0.022″ NiTi wire developed median angles of 26.7, 29.8, and 38.7° with the three ligatures, respectively, while the 0.018â€³â€¯× 0.025″ SS developed median angles of 12.9, 10.7, and 12.7°, respectively. CONCLUSIONS: The ligature type and geometry did not affect the efficiency of torque control, except for the 0.016â€³â€¯× 0.022″ NiTi wire. The wires generating the greatest moments were the 0.018â€³â€¯× 0.025″ SS and 0.018â€³â€¯× 0.025″ ßIIITi.

Evaluation of Adhesion Between Carbon Fiber Frameworks and Esthetic Veneering Materials.

PURPOSE: To assess bond strength and failure patterns of carbon fiber-reinforced composite (CFRC) and veneering materials. MATERIALS AND METHODS: A total of 20 samples were prepared: 10 veneered with polymethylmethacrylate (group A) and 10 with composite resin (group B). Shear bond strength (SBS) was measured, and failed samples were microscopically observed. RESULTS: The mean ± standard deviation (SD) SBS of specimens in group A was slightly higher (7.39 ± 0.24 MPa) than specimens in group B (5.68 ± 0.29 MPa). Microscopic observation showed an adhesive fracture pattern at the CFRC-adhesive interface in both groups. CONCLUSION: Adhesion between CFRC and veneering material is reliable and predictable, although a specific protocol needs to be developed to improve adhesion.

3D Porous Gelatin/PVA Hydrogel as Meniscus Substitute Using Alginate Micro-Particles as Porogens.

One of the current major challenges in orthopedic surgery is the treatment of meniscal lesions. Some of the main issues include mechanical consistency of meniscal implants, besides their fixation methods and integration with the host tissues. To tackle these aspects we realized a micro-porous, gelatin/polyvinyl alcohol (PVA)-based hydrogel to approach the high percentage of water present in the native meniscal tissue, recapitulating its biomechanical features, and, at the same time, realizing a porous implant, permissive to cell infiltration and tissue integration. In particular, we adopted aerodynamically-assisted jetting technology to realize sodium alginate micro-particles with controlled dimensions to be used as porogens. The porous hydrogels were realized through freezing-thawing cycles, followed by alginate particles leaching. Composite hydrogels showed a high porosity (74%) and an open porous structure, while preserving the elasticity behavior (E = 0.25 MPa) and high water content, typical of PVA-based hydrogels. The ex vivo animal model validation proved that the addition of gelatin, combined with the micro-porosity of the hydrogel, enhanced implant integration with the host tissue, allowing penetration of host cells within the construct boundaries. Altogether, these results show that the combined use of a water-insoluble micro-porogen and gelatin, as a bioactive agent, allowed the realization of a porous composite PVA-based hydrogel to be envisaged as a potential meniscal substitute.

"Green-reduced" graphene oxide induces in vitro an enhanced biomimetic mineralization of polycaprolactone electrospun meshes.

A novel green method for graphene oxide (GO) reduction via ascorbic acid has been adopted to realize bio-friendly reduced graphene oxide (RGO)/polycaprolactone (PCL) nanofibrous meshes, as substrates for bone tissue engineering applications. PCL fibrous mats enriched with either RGO or GO (0.25 wt%) were fabricated to recapitulate the fibrillar structure of the bone extracellular matrix (ECM) and the effects of RGO incorporation on the structural proprieties, biomechanics and bioactivity of the nano-composites meshes were evaluated. RGO/PCL fibrous meshes displayed superior mechanical properties (i.e. Young's Modulus and ultimate tensile strength) besides supporting noticeably improved cell adhesion, spreading and proliferation of fibroblasts and osteoblast-like cell lines. Furthermore, RGO-based electrospun substrates enhanced in vitro calcium deposition in the ECM produced by osteoblast-like cells, which was paralleled, in human mesenchymal stem cells grown onto the same substrates, by an increased expression of the osteogenic markers mandatory for mineralization. In this respect, the capability of graphene-based materials to adsorb osteogenic factors cooperates synergically with the rougher surface of RGO/PCL-based materials, evidenced by AFM analysis, to ignite mineralization of the neodeposited matrix and to promote the osteogenic commitment of the cultured cell in the surrounding microenvironment.

Adsorption of paraffin vapor on oxidized molybdenum substrates at nano- and micro-scales.

Sputtered oxidized molybdenum surfaces were exposed at room temperature for different times to paraffin vapors obtained at 150 degrees C. Scanning polarization force microscopy (SPFM), optical and confocal microscopy were used to characterize the surfaces. The condensed morphologies are complex and strongly dependent upon the quantity of vapor molecules deposited on the substrate surface. A thin paraffin film is initially formed and quite uniform nano-height drops are nucleated randomly over it within 10-20 s time exposures. Their average contact angle ranged between 1 degrees -2.5 degrees . Further vapor deposition led to a more complex regime where nano-height drops do not show a clear interface with the film, while micro-sized drops do. The tangent approximation method adopted by Salmeron and Xu for the nano-drop regimes was extended to the micro-sized drop regime obtaining an averaged effective contact angle equal to 4 degrees -5 degrees . Both nano-height and micro-sized drops shape and effective contact angles have been discussed taking into account their interactions between the film and the drops.

Molecular level interactions in brushite-aminoacids composites.

The interaction of aminoacids (Glycine, Proline, Lysine) with brushite based bone cements has been investigated by several techniques (FTIR spectroscopy, Thermogravimetry-TG, Scanning Electron Microscopy-SEM, mechanical properties studies), with the aim to elucidate the properties of the resulting composite materials and the interaction occurring at molecular level between the inorganic matrix and the organic moieties. Brushite phase is predominantly obtained also in the presence of aminoacids added during preparation of the bone cement. Focusing on Glycine incorporation, the presence of a fraction of bulk Glycine, weakly interacting with the inorganic matrix, together with Glycine specifically interacting with adsorption sites can be envisaged, as pointed out by FT IR and thermogravimetric data. In detail, FT-IR data evidenced changes in shape and position of bands associated to stretching modes of the carboxylic groups in Glycine structure, which can be explained by the coordination of these functional groups with the Ca ions in the matrix. Heating this composite at controlled temperature results in the detection of a condensation products, either cyclic condensation product, either dipeptide. Diffuse and not specific H-bonding seems to be the main form of interaction of Proline and Lysine with brushite. Due to the coordination with Ca ions here described, Glycine can act as retardant during brushite preparation, allowing good workability of the resulting composite.

New in-situ synthetized hydrogel composite based on alginate and brushite as a potential pH sensitive drug delivery system.

A Series of in-situ alginate-brushite (Alg-Bru) hydrogel composites were fabricated to optimize release profile of ibuprofen (Ibu) and to avoid burst releases associated with the pure form of the hydrogels. The Bru crystals were synthetized and dispersed during the crosslinking process of Alg matrix. The beads with different formulations were subject to various characterization tests such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), dynamic mechanical analysis (DMA), and swelling. In addition, the entrapment Efficiency (%EE) and drug release profile were obtained to investigate the impacts of initial concentration of Alg and content of Bru on these parameters. FTIR and XRD outcomes confirmed the successful fabricating of Alg-Bru composite as well as the loading of Ibu. Besides, the results showed that the presence of Bru within Alg matrix restricted polymer chain movement, improved mechanical properties, and decreased swelling ratio. Although the presence of Bru crystals did not improve%EE, they optimized the release profile in a more gradual manner.

Biological and mechanical characterization of carbon fiber frameworks for dental implant applications.

OBJECTIVES: The aim of the present study was to investigate the biocompatibility and mechanical characteristics of dental implant frameworks made of carbon fiber composite. METHODS: The biocompatibility of intact samples and fragments was evaluated by cell count and MTT test according to EN-ISO 10993-5:2009 directions. Destructive and non-destructive mechanical tests were performed in order to evaluate: porosity, static and dynamic elastic modulus of carbon fiber samples. These tests were conducted on different batches of samples manufactured by different dental technicians. The samples were evaluated by optical microscope and by SEM. A compression test was performed to compare complete implant-supported fixed dentures, provided with a metal or carbon fiber framework. RESULTS: Carbon fiber intact and fragmented samples showed optimal biocompatibility. Manufacture technique strongly influenced the mechanical characteristics of fiber-reinforced composite materials. The implant-supported full-arch fixed denture provided with a carbon fiber framework, showed a yield strength comparable to the implant-supported full-arch fixed denture, provided with a metal framework. SIGNIFICANCE: Carbon fiber-reinforced composites demonstrated optimal biocompatibility and mechanical characteristics. They appear suitable for the fabrication of frameworks for implant-supported full-arch dentures. Great attention must be paid to manufacture technique as it strongly affects the material mechanical characteristics.

Characterization of alginate-brushite in-situ hydrogel composites.

In the present study alginate-brushite composite hydrogels were in-situ synthetized and characterized with respect to preparation parameters. Specifically, the influence of initial pH value and initial concentration of phosphate precursor on the in-situ fabrication of the composite hydrogel were taken into account. The composite hydrogels were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), thermogravimetric (TGA, DTG) and differential thermal analysis (DTA). Finally, the cell viability tests were carried out (MTT) over the incubation time period of 3, 7, and 14days. The results revealed that the formation and the crystalline stability of brushite were highly dependent on the initial pH value. It was shown that as the pH reached to the value of 6, characteristics peaks of brushite appeared in the FTIR spectra. Besides, the XRD and thermal analysis results were in a good accordance with those of FTIR. In addition, the SEM images demonstrated that the plate like brushite was formed inside the alginate matrix. Also, a considerable impact of pH variation on the biocompatibility of samples was noticed so that the majority of samples especially those prepared in the acidic conditions were toxic.

Torque Loss After Miniscrew Placement: An In-Vitro Study Followed by a Clinical Trial.

To evaluate torque loss a week after insertion, both in an in vivo and an in vitro experimental setup were designed. In the in vivo setup a total of 29 miniscrews were placed in 20 patients who underwent orthodontic treatment. Maximum insertion torque (MIT) was evaluated at insertion time (T1). A week later, insertion torque was measured again by applying a quarter turn (T2); no load was applied on the screw during the first week. In the in vitro setup a total of 20 miniscrews were placed in pig rib bone samples. MIT was evaluated at insertion time (T1). Bone samples were kept in saline solution and controlled environment for a week during which the solution was refreshed every day. Afterwards, torque was measured again by applying a quarter turn (T2). The comparison of MIT over time was done calculating the percentage difference of the torque values between pre- and post-treatment and using the parametric two independent samples t-test or the non-parametric Mann-Whitney test. After a week unloaded miniscrews showed a mean loss of rotational torque of 36.3% and 40.9% in in vitro and in in vivo conditions, respectively. No statistical differences were found between the two different setups. Torque loss was observed after the first week in both study models; in vitro experimental setup provided a reliable study model for studying torque variation during the first week after insertion.

Effect of Framework in an Implant-Supported Full-Arch Fixed Prosthesis: 3D Finite Element Analysis.

PURPOSE: The aim of this study was to analyze through a three-dimensional finite element analysis (3D-FEA) stress distribution on four implants supporting a full-arch implant-supported fixed prosthesis (FFP) using different prosthesis designs. MATERIALS AND METHODS: A 3D edentulous maxillary model was created and four implants were virtually placed into the maxilla and splinted, simulating an FFP without framework, with a cast metal framework, and with a carbon fiber framework. An occlusal load of 150 N was applied, stresses were transmitted into peri-implant bone, and prosthodontic components were recorded. RESULTS: 3D-FEA revealed higher stresses on the implants (up to +55.16%), on peri-implant bone (up to +56.93%), and in the prosthesis (up to +70.71%) when the full-acrylic prosthesis was simulated. The prosthesis with a carbon fiber framework showed an intermediate behavior between that of the other two configurations. CONCLUSION: This study suggests that the presence of a rigid framework in full-arch fixed prostheses provides a better load distribution that decreases the maximum values of stress at the levels of implants, prosthesis, and maxillary bone.