Printable G-Putty for Frequency- and Rate-Independent, High-Performance Strain Sensors.

While nanocomposite electromechanical sensors are expected to display reasonable conductivity and high sensitivity, little consideration is given to eliminating hysteresis and strain rate/frequency dependence from their response. For example, while G-putty, a composite of graphene and polysiloxane, has very high electromechanical sensitivity, its extreme viscoelasticity renders it completely unsuitable for real sensors due to hysteretic and rate-/frequency-dependent effects. Here it is shown that G-putty can be converted to an ink and printed into patterned thin films on elastic substrates. A partial graphene-polymer phase segregation during printing increases the thin-film conductivity by ×106 compared to bulk, while the mechanical effects of the substrate largely suppress hysteresis and completely remove strain rate and frequency dependence. This allows the fabrication of practical, high-gauge-factor, wearable sensors for pulse measurements as well as patterned sensors for low-signal vibration sensing.

Low cost, high performance ultrafiltration membranes from glass fiber-PTFE-graphene composites.

The development of low-cost ultrafiltration membranes with relatively high flow rate and selectivity is an important goal which could improve access to clean water in the developing world. Here we demonstrate a method to infuse mixtures of graphene nanosheets and Teflon nanoparticles into ultra-cheap glass fibre membranes. Annealing the resultant composites leads to coalescence of the Teflon, resulting in very stable membranes with significantly enhanced mechanical properties. In filtration tests, while adding ~ 10 wt% graphene/Teflon to the glass fibre membrane decreased the flow rate by × 100, the selectivity improved by × 103 compared to the neat glass fibre membrane. This combination of selectively and flow rate was significantly better than any commercial membrane tested under similar circumstances. We found these membranes could remove > 99.99% of 25-250 nm diameter SiC nanoparticles dispersed in ethanol, transmitting only particles with diameters < 40 nm, performance which is superior to commercial alumina membranes. Field trials on dirty canal water showed these composite membranes to remove aluminium to a level × 10 below the EU limit for drinking water and reduce iron and bacteria contents to below detectable levels.

Negative Gauge Factor Piezoresistive Composites Based on Polymers Filled with MoS2 Nanosheets.

Nanocomposite strain sensors, particularly those consisting of polymer-graphene composites, are increasingly common and are of great interest in the area of wearable sensors. In such sensors, application of strain yields an increase in resistance due to the effect of deformation on interparticle junctions. Typically, widening of interparticle separation is thought to increase the junction resistance by reducing the probability of tunnelling between conducting particles. However, an alternative approach would be to use piezoresistive fillers, where an applied strain modifies the intrinsic filler resistance and so the overall composite resistance. Such an approach would broaden sensing capabilities, as using negative piezoresistive fillers could yield strain-induced resistance reductions rather than the usual resistance increases. Here, we introduce nanocomposites based on polyethylene oxide (PEO) filled with MoS2 nanosheets. Doping of the MoS2 by the PEO yields nanocomposites which are conductive enough to act as sensors, while efficient stress transfer leads to nanosheet deformation in response to an external strain. The intrinsic negative piezoresistance of the MoS2 leads to a reduction of the composite resistance on the application of small tensile strains. However, at higher strain the resistance grows due to increases in junction resistance. MoS2-PEO composite gauge factors are approximately -25 but fall to -12 for WS2-PEO composites and roughly -2 for PEO filled with MoSe2 or WSe2. We develop a simple model, which describes all these observations. Finally, we show that these composites can be used as dynamic strain sensors.

Electroconductive Biohybrid Collagen/Pristine Graphene Composite Biomaterials with Enhanced Biological Activity.

Electroconductive substrates are emerging as promising functional materials for biomedical applications. Here, the development of biohybrids of collagen and pristine graphene that effectively harness both the biofunctionality of the protein component and the increased stiffness and enhanced electrical conductivity (matching native cardiac tissue) obtainable with pristine graphene is reported. As well as improving substrate physical properties, the addition of pristine graphene also enhances human cardiac fibroblast growth while simultaneously inhibiting bacterial attachment (Staphylococcus aureus). When embryonic-stem-cell-derived cardiomyocytes (ESC-CMs) are cultured on the substrates, biohybrids containing 32 wt% graphene significantly increase metabolic activity and cross-striated sarcomeric structures, indicative of the improved substrate suitability. By then applying electrical stimulation to these conductive biohybrid substrates, an enhancement of the alignment and maturation of the ESC-CMs is achieved. While this in vitro work has clearly shown the potential of these materials to be translated for cardiac applications, it is proposed that these graphene-based biohybrid platforms have potential for a myriad of other applications-particularly in electrically sensitive tissues, such as neural and neural and musculoskeletal tissues.