Assessment of antimicrobial activity of melittin encapsulated in bicontinuous microemulsions prepared using renewable oils.

The objective of this study is to demonstrate that melittin, a well-studied antimicrobial peptide (AMP), can be solubilized in an active form in bicontinuous microemulsions (BMEs) that employ biocompatible oils. The systems investigated consisted of Winsor-III and -IV BME phases composed of Water/Aerosol-OT (AOT)/Polysorbate 85/isopropyl myristate and a Winsor-IV BME employing Polysorbate 80 and limonene. We found that melittin resided in an α-helix-rich configuration and was in an apolar environment for the AOT/Polysorbate 85 Winsor-III system, suggesting that melittin interacted with the surfactant monolayer and was in an active conformation. An apolar environment was also detected for melittin in the two Winsor-IV systems, but to a lesser extent than the Winsor-III system. Small-angle X-ray scattering analysis indicated that melittin at a concentration of 1.0 g/Laq in the aqueous subphase of the Winsor-IV systems led to the greatest impact on the BME structure (e.g., decrease of quasi-periodic repeat distance and correlation length and induction of interfacial fluidity). The antimicrobial activity of the Polysorbate 80 Winsor-IV system was evaluated against several bacteria prominent in chronic wounds and surgical site infections (SSIs). Melittin-free BMEs inhibited the growth of all tested bacteria due to its oil, limonene, while the inclusion of 1.0 g/Laq of melittin in the BMEs enhanced the activity against several bacteria. A further increase of melittin concentration in the BMEs had no further enhancement. These results demonstrate the potential utility of BMEs as a delivery platform for AMPs and other hydrophilic and lipophilic drugs to inhibit antibiotic-resistant microorganisms in chronic wounds and SSIs.

Extending synchrotron SAXS instrument ranges through addition of a portable, inexpensive USAXS module with vertical rotation axes.

Ultra-SAXS can enhance the capabilities of existing synchrotron SAXS/WAXS beamlines. A compact ultra-SAXS module has been developed, which extends the measurable q-range with 0.0015 ≤ q (nm-1) ≤ 0.2, allowing structural dimensions in the range 30 ≤ D (nm) ≤ 4000 to be probed in addition to the range covered by a high-end SAXS/WAXS instrument. By shifting the module components in and out on their respective motor stages, SAXS/WAXS measurements can be easily and rapidly interleaved with USAXS measurements. The use of vertical crystal rotation axes (horizontal diffraction) greatly simplifies the construction, at minimal cost to efficiency. In this paper, the design considerations, realization and synchrotron findings are presented. Measurements of silica spheres, an alumina membrane, and a porous carbon catalyst are provided as application examples.

Molecular packing structure of fibrin fibers resolved by X-ray scattering and molecular modeling.

Fibrin is the major extracellular component of blood clots and a proteinaceous hydrogel used as a versatile biomaterial. Fibrin forms branched networks built of laterally associated double-stranded protofibrils. This multiscale hierarchical structure is crucial for the extraordinary mechanical resilience of blood clots, yet the structural basis of clot mechanical properties remains largely unclear due, in part, to the unresolved molecular packing of fibrin fibers. Here the packing structure of fibrin fibers is quantitatively assessed by combining Small Angle X-ray Scattering (SAXS) measurements of fibrin reconstituted under a wide range of conditions with computational molecular modeling of fibrin protofibrils. The number, positions, and intensities of the Bragg peaks observed in the SAXS experiments were reproduced computationally based on the all-atom molecular structure of reconstructed fibrin protofibrils. Specifically, the model correctly predicts the intensities of the reflections of the 22.5 nm axial repeat, corresponding to the half-staggered longitudinal arrangement of fibrin molecules. In addition, the SAXS measurements showed that protofibrils within fibrin fibers have a partially ordered lateral arrangement with a characteristic transverse repeat distance of 13 nm, irrespective of the fiber thickness. These findings provide fundamental insights into the molecular structure of fibrin clots that underlies their biological and physical properties.

Polycapillary Optics Based Confocal Micro X-ray Fluorescence and X-ray Absorption Spectroscopy Setup at The European Synchrotron Radiation Facility Collaborative Research Group Dutch-Belgian Beamline, BM26A.

A novel plug-and-play setup based on polycapillary X-ray optics enables three-dimensional (3D) confocal X-ray fluorescence (XRF) and X-ray absorption spectroscopy down to 8 × 8 × 11 µm3 (17 keV) at the European Synchrotron Radiation Facility Collaborative Research Group Dutch-Belgian Beamline, BM26A. A complete description and analytical characterization is presented, together with two recently performed experimental cases. In Deep Earth diamond São Luiz-Frankfurt am Main 16, an olivine-rich inclusion was mapped with full 3D XRF elemental imaging. The preliminary tests on Iron Gall ink contained in an historical document, a letter from the court of King Philip II of Spain, reveal both the delicate nature of Iron Gall ink and the lack of Fe-Ni chemical bonding.

Selective molecular annealing: in situ small angle X-ray scattering study of microwave-assisted annealing of block copolymers.

Microwave annealing has emerged as an alternative to traditional thermal annealing approaches for optimising block copolymer self-assembly. A novel sample environment enabling small angle X-ray scattering to be performed in situ during microwave annealing is demonstrated, which has enabled, for the first time, the direct study of the effects of microwave annealing upon the self-assembly behavior of a model, commercial triblock copolymer system [polystyrene-block-poly(ethylene-co-butylene)-block-polystyrene]. Results show that the block copolymer is a poor microwave absorber, resulting in no change in the block copolymer morphology upon application of microwave energy. The block copolymer species may only indirectly interact with the microwave energy when a small molecule microwave-interactive species [diethylene glycol dibenzoate (DEGDB)] is incorporated directly into the polymer matrix. Then significant morphological development is observed at DEGDB loadings ≥6 wt%. Through spatial localisation of the microwave-interactive species, we demonstrate targeted annealing of specific regions of a multi-component system, opening routes for the development of "smart" manufacturing methodologies.

Molecular ordering in the high-temperature nematic phase of an all-aromatic liquid crystal.

We report the structural characterization of the nematic phase of 2,6-biphenyl naphthalene (PPNPP). This lath-like all-aromatic mesogen provides a valuable benchmark for classical theories of nematic order. PPNPP exhibits a very high temperature nematic phase (417-489 °C) above an enantiotropic smectic A phase. X-ray diffraction reveals a surprisingly strong tendency towards molecular layering in the nematic phase, indicative of "normal cybotaxis" (i.e. SmA-like stratification within clusters of mesogens). Although stronger at low temperatures, the layering is evident well above the smectic A-nematic transition. The nematic order parameter is evaluated as a function of temperature from the broadening of the wide-angle diffuse diffraction feature. Measured values of the orientational order parameter are slightly larger than those predicted by the Maier-Saupe theory over the entire nematic range except for a narrow region just below the clearing point where they significantly drop below the theoretical prediction.

Photon Energy Becomes the Third Dimension in Crystallographic Texture Analysis.

Conventional analysis of the preferred orientation of crystallites (crystallographic texture) involves X-ray diffraction with area detectors and 2D data output. True 3D, spatially resolved information requires sample rotation in the beam, thus changing the probed volume, which introduces signal smearing and precludes the scanning of complex structures. This obstacle has been overcome by energy-dispersive Laue diffraction. A method has been devised to reach a large portion of reciprocal space and translate the X-ray photon energy into the missing third dimension of space. Carbon fibers and lobster exoskeleton as examples of biomineralized tissue have been analyzed. The major potential of this method lies in its "one-shot" nature and the direct 3D information requiring no previous knowledge of the sample. It allows the texture of large samples with complex substructures to be scanned and opens up the conceptual possibility of following texture changes in situ, for example, during crystallization.

In Situ Observation of Active Oxygen Species in Fe-Containing Ni-Based Oxygen Evolution Catalysts: The Effect of pH on Electrochemical Activity.

Ni-based oxygen evolution catalysts (OECs) are cost-effective and very active materials that can be potentially used for efficient solar-to-fuel conversion process toward sustainable energy generation. We present a systematic spectroelectrochemical characterization of two Fe-containing Ni-based OECs, namely nickel borate (Ni(Fe)-B(i)) and nickel oxyhydroxide (Ni(Fe)OOH). Our Raman and X-ray absorption spectroscopy results show that both OECs are chemically similar, and that the borate anions do not play an apparent role in the catalytic process at pH 13. Furthermore, we show spectroscopic evidence for the generation of negatively charged sites in both OECs (NiOO(-)), which can be described as adsorbed "active oxygen". Our data conclusively links the OER activity of the Ni-based OECs with the generation of those sites on the surface of the OECs. The OER activity of both OECs is strongly pH dependent, which can be attributed to a deprotonation process of the Ni-based OECs, leading to the formation of the negatively charged surface sites that act as OER precursors. This work emphasizes the relevance of the electrolyte effect to obtain catalytically active phases in Ni-based OECs, in addition to the key role of the Fe impurities. This effect should be carefully considered in the development of Ni-based compounds meant to catalyze the OER at moderate pHs. Complementarily, UV-vis spectroscopy measurements show strong darkening of those catalysts in the catalytically active state. This coloration effect is directly related to the oxidation of nickel and can be an important factor limiting the efficiency of solar-driven devices utilizing Ni-based OECs.

Self-Assembly-Driven Electrospinning: The Transition from Fibers to Intact Beaded Morphologies.

Polymer beads have attracted considerable interest for use in catalysis, drug delivery, and photonics due to their particular shape and surface morphology. Electrospinning, typically used for producing nanofibers, can also be used to fabricate polymer beads if the solution has a sufficiently low concentration. In this work, a novel approach for producing more uniform, intact beads is presented by electrospinning self-assembled block copolymer (BCP) solutions. This approach allows a relatively high polymer concentration to be used, yet with a low degree of entanglement between polymer chains due to microphase separation of the BCP in a selective solvent system. Herein, to demonstrate the technology, a well-studied polystyrene-poly(ethylene butylene)-polystyrene triblock copolymer is dissolved in a co-solvent system. The effect of solvent composition on the characteristics of the fibers and beads is intensively studied, and the mechanism of this fiber-to-bead is found to be dependent on microphase separation of the BCP.

Evaluation of an X-ray-excited optical microscope for chemical imaging of metal and other surfaces.

The application of a modular system for the nondestructive chemical imaging of metal and other surfaces is described using heritage metals as an example. The custom-built X-ray-excited optical luminescence (XEOL) microscope, XEOM 1, images the chemical state and short-range atomic order of the top 200 nm of both amorphous and crystalline surfaces. A broad X-ray beam is used to illuminate large areas (up to 4 mm(2)) of the sample, and the resulting XEOL emission is collected simultaneously for each pixel by a charge-coupled device sensor to form an image. The input X-ray energy is incremented across a range typical for the X-ray absorption near-edge structure (XANES) and an image collected for each increment. The use of large-footprint beams combined with parallel detection allows the power density to be kept low and facilitates complete nondestructive XANES mapping on a reasonable time scale. In this study the microscope was evaluated by imaging copper surfaces with well-defined patterns of different corrosion products (cuprite Cu2O and nantokite CuCl). The images obtained show chemical contrast, and filtering the XEOL light allowed different corrosion products to be imaged separately. Absorption spectra extracted from software-selected regions of interest exhibit characteristic XANES fingerprints for the compounds present. Moreover, when the X-ray absorption edge positions were extracted from each spectrum, an oxidation state map of the sample could be compiled. The results show that this method allows one to obtain nondestructive and noninvasive information at the micrometer scale while using full-field imaging.

Full-field fluorescence mode micro-XANES imaging using a unique energy dispersive CCD detector.

X-ray absorption near-edge structure (XANES) spectroscopy is a well-known nondestructive technique that allows for chemical state and local structure determination. Spatially resolved oxidation state imaging is possible performing full-field transmission mode XANES experiments, providing chemical state information on the illuminated sample area, but these experiments are limited to thin, concentrated samples. Here we present the use of a unique energy dispersive (ED) pnCCD detector, the SLcam, for full-field fluorescence mode XANES experiments, thereby significantly relaxing the constraints on sample thickness. Using this new detection methodology, spatially resolved chemical state information on millimeter-sized sample areas can be obtained with microscopic resolution in moderate measuring times (less than 15 h), obtaining a XANES profile for each of nearly 70,000 points in a single measurement without the need of scanning the sample through the beam. Besides a description of the use of this detector for micro-XANES applications, we also present the proof of concept for fluorescence mode micro-XANES using a Fe(0)/Fe2O3 model sample and a Nitisol soil sample, which was measured to obtain iron chemical state distribution information.

Position and flux stabilization of X-ray beams produced by double-crystal monochromators for EXAFS scans at the titanium K-edge.

The simultaneous and active feedback stabilization of X-ray beam position and monochromatic beam flux during EXAFS scans at the titanium K-edge as produced by a double-crystal monochromator beamline is reported. The feedback is generated using two independent feedback loops using separate beam flux and position measurements. The flux is stabilized using a fast extremum-searching algorithm that is insensitive to changes in the synchrotron ring current and energy-dependent monochromator output. Corrections of beam height are made using an innovative transmissive beam position monitor instrument. The efficacy of the feedback stabilization method is demonstrated by comparing the measurements of EXAFS spectra on inhomogeneous diluted Ti-containing samples with and without feedback applied.

A high-pressure and controlled-flow gas system for catalysis research.

A high-pressure gas rig for in situ catalytic reactions at X-ray absorption spectroscopy beamline (BM26A) has been developed. The rig enables catalysts to be studied in a variety of cells under well controlled and industrially relevant operation conditions. A large variety of gas mixtures can be generated and pressures of up to 50 bar with dry gas and 20 bar with wet gas (steam) can be obtained. Analyses of reaction products can be performed using an on-line mass spectrometer.

Energy-resolved electron-yield XAS studies of nanoporous CoAlPO-18 and CoAlPO-34 catalysts.

Energy-resolved electron-yield X-ray absorption spectroscopy is a promising technique for probing the near-surface structure of nanomaterials because of its ability to discriminate between the near-surface and bulk of materials. So far, the technique has only been used in model systems. Here, the local structural characterization of nanoporous cobalt-substituted aluminophosphates is reported and it is shown that the technique can be employed for the study of open-framework catalytically active systems. Evidence that the cobalt ions on the surface of the crystals react differently to those in the bulk is found.

Influence of metal-support interaction on the surface structure of gold nanoclusters deposited on native SiO(x)/Si substrates.

The structure of small gold nanoclusters (around 2.5 nm) deposited on different silica-on-silicon (SiOx/Si) substrates is investigated using several characterization techniques (AFM, XRD, EXAFS and GISAXS). The grain morphology and the surface roughness of the deposited gold cluster layers are determined by AFM. The in-plane GISAXS intensity is modelled in order to obtain information about the cluster size and the characteristic length scale of the surface roughness. The surface morphology of the deposited clusters depends on whether the native defect-rich (n-SiOx/Si) or the defect-poor substrate obtained by thermal treatment (t-SiO2/Si) is used. Gold clusters show a stronger tendency to aggregate when deposited on n-SiOx/Si, resulting in films characterized by a larger grain dimension (around 20 nm) and by a higher surface roughness (up to 5 nm). The more noticeable cluster aggregation on n-SiOx/Si substrates is explained in terms of metal-support interaction mediated by the defects located on the surface of the native silica substrate. Evidence of metal-support interaction is provided by EXAFS, demonstrating the existence of an Au-O distance for clusters deposited on n-SiOx/Si that is not found on t-SiO2/Si.

Structure and speciation of chromium ions in chromium doped Fe2O3 catalysts.

In this paper, we report a detailed characterisation of chromium doped iron oxide catalysts using a range of techniques to establish the nature of chromium species in the near surface and bulk of iron oxide, high-temperature shift (HTS) catalysts. In particular we have employed X-ray absorption spectroscopy Cr K-edge near edge and extended fine structure data for comparison with chemical and X-ray photoelectron spectroscopy. There was excellent agreement between the techniques in terms of identification and quantification of Cr(6+) and Cr(3+) species as a function of calcination temperatures between 100 and 500 °C.

The skin barrier: An extraordinary interface with an exceptional lipid organization.

The barrier function of the skin is primarily located in the stratum corneum (SC), the outermost layer of the skin. The SC is composed of dead cells with highly organized lipid lamellae in the intercellular space. As the lipid matrix forms the only continuous pathway, the lipids play an important role in the permeation of compounds through the SC. The main lipid classes are ceramides (CERs), cholesterol (CHOL) and free fatty acids (FFAs). Analysis of the SC lipid matrix is of crucial importance in understanding the skin barrier function, not only in healthy skin, but also in inflammatory skin diseases with an impaired skin barrier. In this review we provide i) a historical overview of the steps undertaken to obtain information on the lipid composition and organization in SC of healthy skin and inflammatory skin diseases, ii) information on the role CERs, CHOL and FFAs play in the lipid phase behavior of very complex lipid model systems and how this knowledge can be used to understand the deviation in lipid phase behavior in inflammatory skin diseases, iii) knowledge on the role of both, CER subclasses and chain length distribution, on lipid organization and lipid membrane permeability in complex and simple model systems with synthetic CERs, CHOL and FFAs, iv) similarity in lipid phase behavior in SC of different species and complex model systems, and vi) future directions in modulating lipid composition that is expected to improve the skin barrier in inflammatory skin diseases.

Synthesis and Characterization of Stimuli-Responsive Polymer Brushes in Nanofluidic Channels.

Nanochannels with controllable gating behavior are attractive features in a wide range of nanofluidic applications including viral detection, particle sorting, and flow regulation. Here, we use selective sidewall functionalization of nanochannels with a polyelectrolyte brush to investigate the channel gating response to variations in solution pH and ionic strength. The conformational and structural changes of the interfacial brush layer within the channels are interrogated by specular and off-specular neutron reflectometry. Simultaneous fits of the specular and off-specular signals, using a dynamical theory model and a fitting optimization protocol, enable detailed characterization of the brush conformations and corresponding channel geometry under different solution conditions. Our results indicate a collapsed brush state under basic pH, equivalent to an open gate, and an expanded brush state representing a partially closed gate upon decreasing the pH and salt concentration. These findings open new possibilities in noninvasive in situ characterization of tunable nanofluidics and lab-on-chip devices with advanced designs and improved functionality.

Increase in short-chain ceramides correlates with an altered lipid organization and decreased barrier function in atopic eczema patients.

A hallmark of atopic eczema (AE) is skin barrier dysfunction. Lipids in the stratum corneum (SC), primarily ceramides, fatty acids, and cholesterol, are crucial for the barrier function, but their role in relation to AE is indistinct. Filaggrin is an epithelial barrier protein with a central role in the pathogenesis of AE. Nevertheless, the precise causes of AE-associated barrier dysfunction are largely unknown. In this study, a comprehensive analysis of ceramide composition and lipid organization in nonlesional SC of AE patients and control subjects was performed by means of mass spectrometry, infrared spectroscopy, and X-ray diffraction. In addition, the skin barrier and clinical state of the disease were examined. The level of ceramides with an extreme short chain length is drastically increased in SC of AE patients, which leads to an aberrant lipid organization and a decreased skin barrier function. Changes in SC lipid properties correlate with disease severity but are independent of filaggrin mutations. We demonstrate for the first time that changes in ceramide chain length and lipid organization are directly correlated with the skin barrier defects in nonlesional skin of AE patients. We envisage that these insights will provide a new therapeutic entry in therapy and prevention of AE.

Ionic Conductivity Enhancement of Polymer Electrolytes by Directed Crystallization.

We report that hot stretching of poly(ethylene oxide) (PEO)-based solid polymer electrolytes (SPEs) can lead to a preferred orientation of PEO crystalline lamellae, thereby reducing the tortuosity of the ion-conduction pathway along the thickness direction of the SPE film, causing improved ionic conductivity. The hot stretching method is implemented by stretching SPE films above the melting point of PEO in an inert environment followed by crystallization at room temperature while maintaining the applied strain. The effect of hot stretching on the crystalline orientation, crystallinity, morphology, and ion transport in PEO with two types of salts, lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and lithium triflate (LiCF3SO3), is investigated in detail. Wide-angle X-ray scattering (WAXS) and small-angle X-ray scattering (SAXS) show that the orientation of PEO crystalline lamellae induces the formation of a short ion-conduction pathway along the through-plane direction of the SPE films, leading to 1.4- to 3.5-fold enhancement in the through-plane ionic conductivity.