Molecular parameters responsible for thermally activated transport in doped organic semiconductors.

Doped organic semiconductors typically exhibit a thermal activation of their electrical conductivity, whose physical origin is still under scientific debate. In this study, we disclose relationships between molecular parameters and the thermal activation energy (EA) of the conductivity, revealing that charge transport is controlled by the properties of host-dopant integer charge transfer complexes (ICTCs) in efficiently doped organic semiconductors. At low doping concentrations, charge transport is limited by the Coulomb binding energy of ICTCs, which can be minimized by systematic modification of the charge distribution on the individual ions. The investigation of a wide variety of material systems reveals that static energetic disorder induced by ICTC dipole moments sets a general lower limit for EA at large doping concentrations. The impact of disorder can be reduced by adjusting the ICTC density and the intramolecular relaxation energy of host ions, allowing an increase of conductivity by many orders of magnitude.

Insight into doping efficiency of organic semiconductors from the analysis of the density of states in n-doped C60 and ZnPc.

Doping plays a crucial role in semiconductor physics, with n-doping being controlled by the ionization energy of the impurity relative to the conduction band edge. In organic semiconductors, efficient doping is dominated by various effects that are currently not well understood. Here, we simulate and experimentally measure, with direct and inverse photoemission spectroscopy, the density of states and the Fermi level position of the prototypical materials C60 and zinc phthalocyanine n-doped with highly efficient benzimidazoline radicals (2-Cyc-DMBI). We study the role of doping-induced gap states, and, in particular, of the difference Δ1 between the electron affinity of the undoped material and the ionization potential of its doped counterpart. We show that this parameter is critical for the generation of free carriers and influences the conductivity of the doped films. Tuning of Δ1 may provide alternative strategies to optimize the electronic properties of organic semiconductors.

Self-Assembly of Tetraphenyldibenzoperiflanthene (DBP) Films on Ag(111) in the Monolayer Regime.

Tetraphenyldibenzoperiflanthene (DBP) is a promising candidate as a component of highly efficient organic photovoltaic cells and organic light-emitting diodes. The structural properties of thin films of this particular lander-type molecule on Ag(111) were investigated by complementary techniques. Highly ordered structures were obtained, and their mutual alignment was characterized by means of low-energy electron diffraction (LEED). Scanning tunneling microscopy (STM) images reveal two slightly different arrangements within the first monolayer (ML), both describable as specific herringbone patterns with two molecules per unit cell whose dibenzoperiflanthene framework is parallel to the surface. In contrast, single DBP molecules in the second ML were imaged with much higher intramolecular resolution, resembling the shape of the frontier orbitals in the gas phase as calculated by means of density functional theory (DFT). Further deposition leads to the growth of highly ordered bilayer islands on top of the first ML with identical unit cell dimensions and orientation but slightly inclined molecules. This suggests that the first ML acts as a template for the epitaxial growth of further layers. Simultaneously, a significant number of second-layer molecules mainly located at step edges or scattered over narrow terraces do not form highly ordered aggregates.

Role of S-Vacancy Concentration in Air Oxidation of WS2 Single Crystals.

Semiconducting transition metal dichalcogenides (TMDs) are a class of two-dimensional materials with potential applications in optoelectronics, spintronics, valleytronics, and quantum information processing. Understanding their stability under ambient conditions is critical for determining their in-air processability during device fabrication and for predicting their long-term device performance stability. While the effects of environmental conditions (i.e., oxygen, moisture, and light) on TMD degradation are well-acknowledged, the role of defects in driving their oxidation remains unclear. We conducted a systematic X-ray photoelectron spectroscopy study on WS2 single crystals with different surface S-vacancy concentrations formed via controlled argon sputtering. Oxidation primarily occurred at defect concentrations ≥ 10%, resulting in stoichiometric WO3 formation, while a stable surface was observed at lower concentrations. Theoretical calculations informed us that single S-vacancies do not spontaneously oxidize, while defect pairing at high vacancy concentrations facilitates O2 dissociation and subsequent oxide formation. Our XPS results also point to vacancy-related structural and electrostatic disorder as the main origin for the p-type characteristics that persists even after oxidation. Despite the complex interplay between defects and TMD oxidation processes, our work unveils scientifically informed guidance for working effectively with TMDs.

Gap states in pentacene thin film induced by inert gas exposure.

We studied gas-exposure effects on pentacene (Pn) films on SiO2 and Au(111) substrates by ultrahigh sensitivity photoelectron spectroscopy, which can detect the density of states of ∼10(16) states eV-1 cm-3 comparable to electrical measurements. The results show the striking effects for Pn/SiO2: exposure to inert gas (N2 and Ar) produces a sharp rise in gap states from ∼10(16) to ∼10(18) states eV-1 cm-3 and pushes the Fermi level closer to the valence band (0.15-0.17 eV), as does exposure to O2 (0.20 eV), while no such gas-exposure effect is observed for Pn/Au(111). The results demonstrate that these gap states originate from small imperfections in the Pn packing structure, which are induced by gas penetration into the film through the crystal grain boundaries.

Toward Edge Engineering of Two-Dimensional Layered Transition-Metal Dichalcogenides by Chemical Vapor Deposition.

The manipulation of edge configurations and structures in atomically-thin transition metal dichalcogenides (TMDs) for versatile functionalization has attracted intensive interest in recent years. The chemical vapor deposition (CVD) approach has shown promise for TMD edge engineering of atomic edge configurations (1H, 1T or 1T'-zigzag or armchair edges) as well as diverse edge morphologies (1D nanoribbons, 2D dendrites, 3D spirals, etc.). These edge-rich TMD layers offer versatile candidates for probing the physical and chemical properties and exploring potential applications in electronics, optoelectronics, catalysis, sensing, and quantum technologies. In this Review, we present an overview of the current state-of-the-art in the manipulation of TMD atomic edges and edge-rich structures using CVD. We highlight the vast range of distinct properties associated with these edge configurations and structures and provide insights into the opportunities afforded by such edge-functionalized crystals. The objective of this Review is to motivate further research and development efforts to use CVD as a scalable approach to harness the benefits of such crystal-edge engineering.

Liquid-Metal-Printed Ultrathin Oxides for Atomically Smooth 2D Material Heterostructures.

Two-dimensional (2D) semiconductors are promising channel materials for continued downscaling of complementary metal-oxide-semiconductor (CMOS) logic circuits. However, their full potential continues to be limited by a lack of scalable high-k dielectrics that can achieve atomically smooth interfaces, small equivalent oxide thicknesses (EOTs), excellent gate control, and low leakage currents. Here, large-area liquid-metal-printed ultrathin Ga2O3 dielectrics for 2D electronics and optoelectronics are reported. The atomically smooth Ga2O3/WS2 interfaces enabled by the conformal nature of liquid metal printing are directly visualized. Atomic layer deposition compatibility with high-k Ga2O3/HfO2 top-gate dielectric stacks on a chemical-vapor-deposition-grown monolayer WS2 is demonstrated, achieving EOTs of ∼1 nm and subthreshold swings down to 84.9 mV/dec. Gate leakage currents are well within requirements for ultrascaled low-power logic circuits. These results show that liquid-metal-printed oxides can bridge a crucial gap in dielectric integration of 2D materials for next-generation nanoelectronics.

Accessing surface Brillouin zone and band structure of picene single crystals.

We have experimentally revealed the band structure and the surface Brillouin zone of insulating picene single crystals (SCs), the mother organic system for a recently discovered aromatic superconductor, with ultraviolet photoelectron spectroscopy (UPS) and low-energy electron diffraction with a laser for photoconduction. A hole effective mass of 2.24m(0) and the hole mobility µ(h)≥9.0 cm(2)/V s (298 K) were deduced in the Γ-Y direction. We have further shown that some picene SCs did not show charging during UPS even without the laser, which indicates that pristine UPS works for high-quality organic SCs.

Gate-Defined Quantum Confinement in CVD 2D WS2.

Temperature-dependent transport measurements are performed on the same set of chemical vapor deposition (CVD)-grown WS2 single- and bilayer devices before and after atomic layer deposition (ALD) of HfO2 . This isolates the influence of HfO2 deposition on low-temperature carrier transport and shows that carrier mobility is not charge impurity limited as commonly thought, but due to another important but commonly overlooked factor: interface roughness. This finding is corroborated by circular dichroic photoluminescence spectroscopy, X-ray photoemission spectroscopy, cross-sectional scanning transmission electron microscopy, carrier-transport modeling, and density functional modeling. Finally, electrostatic gate-defined quantum confinement is demonstrated using a scalable approach of large-area CVD-grown bilayer WS2 and ALD-grown HfO2 . The high dielectric constant and low leakage current enabled by HfO2 allows an estimated quantum dot size as small as 58 nm. The ability to lithographically define increasingly smaller devices is especially important for transition metal dichalcogenides due to their large effective masses, and should pave the way toward their use in quantum information processing applications.

Impact of S-Vacancies on the Charge Injection Barrier at the Electrical Contact with the MoS2 Monolayer.

Making electrical contacts to semiconducting transition metal dichalcogenides (TMDCs) represents a major bottleneck for high device performance, often manifesting as strong Fermi level pinning and high contact resistance. Despite intense ongoing research, the mechanism by which lattice defects in TMDCs impact the transport properties across the contact-TMDC interface remains unsettled. Here we study the impact of S-vacancies on the electronic properties at a MoS2 monolayer interfaced with graphite by photoemission spectroscopy, where the defect density is selectively controlled by Ar sputtering. A clear reduction of the MoS2 core level and valence band binding energies is observed as the defect density increases. The experimental results are explained in terms of (i) gap states' energy distribution and (ii) S-vacancies' electrostatic disorder effect. Our model indicates that the Fermi level pinning at deep S-vacancy gap states is the origin of the commonly reported large electron injection barrier (∼0.5 eV) at the MoS2 ML interface with low work function metals. At the contact with high work function electrodes, S-vacancies do not significantly affect the hole injection barrier, which is intrinsically favored by Fermi level pinning at shallow occupied gap states. Our results clarify the importance of S-vacancies and electrostatic disorder in TMDC-based electronic devices, which could lead to strategies for optimizing device performance and production.

Stacks of nucleic acids as molecular wires: direct measurement of the intermolecular band dispersion in multilayer guanine assemblies.

The intermolecular band dispersion related to the highest occupied molecular orbital in highly ordered, hydrated multilayer films of the DNA base guanine has been measured using photon-energy-dependent ultraviolet photoelectron spectroscopy. A bandwidth of 331 ± 8 meV at room temperature and a small effective mass of about 1.11 times that of a free charge suggest a high intrinsic hole mobility along quasi-one-dimensional stacks formed perpendicular to layered, hydrogen-bound networks.

Bi ordered phases on Cu(100): periodic arrays of dislocations influence the electronic properties.

A single layer of bismuth deposited on the Cu(100) surface forms long range ordered structural phases at various Bi density. A highly ordered c(2 x 2) reconstruction is accomplished at 0.5 ML, further Bi deposition induces a c(9square root of 2 x square root of 2)R45 degrees structure and a subsequent p(10 x 10) phase related to the formation of regular dislocations arrays. The transition from a c(2 x 2) superstructure to the c(9square root of 2 x square root of 2)R45 degrees phase is accompanied by a sudden decrease in the work function. Photoemission measurements reveal that the Bi induced states close to the Fermi level, associated to the c(2 x 2) phase, are strongly quenched when the arrays of dislocations are formed, while at higher binding energies, they undergo an energy shift probably due to a confinement effect. The low-energy single particle excitations and the electron dispersion of the Bi induced states of the c(2 x 2) phase are compared to the electronic states deduced by theoretical band structure obtained by ab initio calculation performed within the embedding method applied to a realistic semi-infinite system.

Can Reconstructed Se-Deficient Line Defects in Monolayer VSe2 Induce Magnetism?

There have been several recent conflicting reports on the ferromagnetism of clean monolayer VSe2 . Herein, the controllable formation of 1D defect line patterns in vanadium diselenide (VSe2 ) monolayers initiated by thermal annealing is presented. Using scanning tunneling microscopy and q-plus atomic force microscopy techniques, the 1D line features are determined to be 8-member-ring arrays, formed via a Se deficient reconstruction process. The reconstructed VSe2 monolayer with Se-deficient line defects displays room-temperature ferromagnetism under X-ray magnetic circular dichroism and magnetic force microscopy, consistent with the density functional theory calculations. This study possibly resolves the controversy on whether ferromagnetism is intrinsic in monolayer VSe2 , and highlights the importance of controlling and understanding the atomic structures of surface defects in 2D crystals, which could play key roles in the material properties and hence potential device applications.

Metallic 1T Phase, 3d1 Electronic Configuration and Charge Density Wave Order in Molecular Beam Epitaxy Grown Monolayer Vanadium Ditelluride.

We present a combined experimental and theoretical study of monolayer vanadium ditelluride, VTe2, grown on highly oriented pyrolytic graphite by molecular-beam epitaxy. Using various in situ microscopic and spectroscopic techniques, including scanning tunneling microscopy/spectroscopy, synchrotron X-ray and angle-resolved photoemission, and X-ray absorption, together with theoretical analysis by density functional theory calculations, we demonstrate direct evidence of the metallic 1T phase and 3d1 electronic configuration in monolayer VTe2 that also features a (4 × 4) charge density wave order at low temperatures. In contrast to previous theoretical predictions, our element-specific characterization by X-ray magnetic circular dichroism rules out a ferromagnetic order intrinsic to the monolayer. Our findings provide essential knowledge necessary for understanding this interesting yet less explored metallic monolayer in the emerging family of van der Waals magnets.

Evidence of Spin Frustration in a Vanadium Diselenide Monolayer Magnet.

Monolayer VSe2 , featuring both charge density wave and magnetism phenomena, represents a unique van der Waals magnet in the family of metallic 2D transition-metal dichalcogenides (2D-TMDs). Herein, by means of in situ microscopy and spectroscopic techniques, including scanning tunneling microscopy/spectroscopy, synchrotron X-ray and angle-resolved photoemission, and X-ray absorption, direct spectroscopic signatures are established, that identify the metallic 1T-phase and vanadium 3d1 electronic configuration in monolayer VSe2 grown on graphite by molecular-beam epitaxy. Element-specific X-ray magnetic circular dichroism, complemented with magnetic susceptibility measurements, further reveals monolayer VSe2 as a frustrated magnet, with its spins exhibiting subtle correlations, albeit in the absence of a long-range magnetic order down to 2 K and up to a 7 T magnetic field. This observation is attributed to the relative stability of the ferromagnetic and antiferromagnetic ground states, arising from its atomic-scale structural features, such as rotational disorders and edges. The results of this study extend the current understanding of metallic 2D-TMDs in the search for exotic low-dimensional quantum phenomena, and stimulate further theoretical and experimental studies on van der Waals monolayer magnets.

Electronic properties of atomically thin MoS2 layers grown by physical vapour deposition: band structure and energy level alignment at layer/substrate interfaces.

We present an analysis of the electronic properties of an MoS2 monolayer (ML) and bilayer (BL) as-grown on a highly ordered pyrolytic graphite (HOPG) substrate by physical vapour deposition (PVD), using lab-based angle-resolved photoemission spectroscopy (ARPES) supported by scanning tunnelling microscopy (STM) and X-ray photoelectron spectroscopy (XPS) for morphology and elemental assessments, respectively. Despite the presence of multiple domains (causing in-plane rotational disorder) and structural defects, electronic band dispersions were clearly observed, reflecting the high density of electronic states along the high symmetry directions of MoS2 single crystal domains. In particular, the thickness dependent direct-to-indirect band gap transition previously reported only for MoS2 layers obtained by exfoliation or via epitaxial growth processes, was found to be also accessible in our PVD grown MoS2 samples. At the same time, electronic gap states were detected, and attributed mainly to structural defects in the 2D layers. Finally, we discuss and clarify the role of the electronic gap states and the interlayer coupling in controlling the energy level alignment at the MoS2/substrate interface.

Analyzing the n-Doping Mechanism of an Air-Stable Small-Molecule Precursor.

Efficient n-doping of organic semiconductors requires electron-donating molecules with small ionization energies, making such n-dopants usually sensitive to degradation under air exposure. A workaround consists in the usage of air-stable precursor molecules containing the actual n-doping species. Here, we systematically analyze the doping mechanism of the small-molecule precursor o-MeO-DMBI-Cl, which releases a highly reducing o-MeO-DMBI radical upon thermal evaporation. n-Doping of N,N-bis(fluoren-2-yl)-naphthalene tetracarboxylic diimide yields air-stable and highly conductive films suitable for application as electron transport layer in organic solar cells. By photoelectron spectroscopy, we determine a reduced doping efficiency at high doping concentrations. We attribute this reduction to a change of the precursor decomposition mechanism with rising crucible temperature, yielding an undesired demethylation at high evaporation rates. Our results do not only show the possibility of efficient and air-stable n-doping, but also support the design of novel air-stable precursor molecules of strong n-dopants.

Modification of Vapor Phase Concentrations in MoS2 Growth Using a NiO Foam Barrier.

Single-layer molybdenum disulfide (MoS2) has attracted significant attention due to its electronic and physical properties, with much effort invested toward obtaining large-area high-quality monolayer MoS2 films. In this work, we demonstrate a reactive-barrier-based approach to achieve growth of highly homogeneous single-layer MoS2 on sapphire by the use of a nickel oxide foam barrier during chemical vapor deposition. Due to the reactivity of the NiO barrier with MoO3, the concentration of precursors reaching the substrate and thus nucleation density is effectively reduced, allowing grain sizes of up to 170 µm and continuous monolayers on the centimeter length scale being obtained. The quality of the monolayer is further revealed by angle-resolved photoemission spectroscopy measurement by observation of a very well resolved electronic band structure and spin-orbit splitting of the bands at room temperature with only two major domain orientations, indicating the successful growth of a highly crystalline and well-oriented MoS2 monolayer.

Core-shell photoabsorption and photoelectron spectra of gas-phase pentacene: experiment and theory.

The C K-edge photoabsorption and 1s core-level photoemission of pentacene (C22H14) free molecules are experimentally measured, and calculated by self-consistent-field and static-exchange approximation ab initio methods. Six nonequivalent C atoms present in the molecule contribute to the C 1s photoemission spectrum. The complex near-edge structures of the carbon K-edge absorption spectrum present two main groups of discrete transitions between 283 and 288 eV photon energy, due to absorption to pi* virtual orbitals, and broader structures at higher energy, involving sigma* virtual orbitals. The sharp absorption structures to the pi* empty orbitals lay well below the thresholds for the C 1s ionizations, caused by strong excitonic and localization effects. We can definitely explain the C K-edge absorption spectrum as due to both final (virtual) and initial (core) orbital effects, mainly involving excitations to the two lowest-unoccupied molecular orbitals of pi* symmetry, from the six chemically shifted C 1s core orbitals.