First experimental results of the cosmic time synchronizer for a wireless, precise, and perpetual time synchronization system.

In 2022, the idea of the cosmic time synchronizer (CTS) was proposed for a precise wireless synchronization of local clocks (<100 ns). Because CTS does not require critical timing information traffic among CTS sensors, the technique can be considered robust against jamming and spoofing. In this work, a small-scale CTS sensor network has been developed and tested for the first time. Good time synchronization performances were obtained for a short-haul configuration (30-35 ns (SD, 1 σ), over 50-60 m). Based on the results of this work, CTS could be potentially conceived as a 'self-adjusting' system, offering high level continuous (perpetual) performances, to be considered either as a backup chain for GPS disciplined oscillators (GPS DO), a standalone standard for frequency and time interval measurements, or as a tool for the dissemination of reference time scales to final users, with improved characteristics in terms of robustness and reliability.

Extensive cosmic showers detection: the importance of timing and the role of GPS in the EEE experiment.

Extreme Energy Events (EEE) is an extended Cosmic Rays (CRs) Observatory, composed of about 60 tracking telescopes spread over more than 10 degrees in Latitude and Longitude. We present the metrological characterization of a representative set of actually installed EEE GPS receivers, their calibration and their comparison with respect to dual-frequency receivers for timing applications, as well as plans for a transportable measurement system to calibrate the currently deployed GPS receivers. Finally, the realization of an INRIM Laboratory dedicated to EEE, aimed at hosting reference telescopes and allowing timing studies for Particle Physics/Astrophysics experiments, is presented, as well as the possibility of synchronizing already deployed telescopes utilizing White Rabbit Technique, over optical fiber links, directly with the Universal Time Coordinated time scale, as realized by INRIM (UTC(IT)).

Calibration of Galileo signals for time metrology.

Using global navigation satellite system (GNSS) signals for accurate timing and time transfer requires the knowledge of all electric delays of the signals inside the receiving system. GNSS stations dedicated to timing or time transfer are classically calibrated only for Global Positioning System (GPS) signals. This paper proposes a procedure to determine the hardware delays of a GNSS receiving station for Galileo signals, once the delays of the GPS signals are known. This approach makes use of the broadcast satellite inter-signal biases, and is based on the ionospheric delay measured from dual-frequency combinations of GPS and Galileo signals. The uncertainty on the so-determined hardware delays is estimated to 3.7 ns for each isolated code in the L5 frequency band, and 4.2 ns for the ionosphere-free combination of E1 with a code of the L5 frequency band. For the calibration of a time transfer link between two stations, another approach can be used, based on the difference between the common-view time transfer results obtained with calibrated GPS data and with uncalibrated Galileo data. It is shown that the results obtained with this approach or with the ionospheric method are equivalent.

Near real-time comparison and monitoring of time scales with precise point positioning using NRCan ultra-rapid products.

This paper experimentally evaluates the assessment of precise point positioning (PPP) using the Natural Resources Canada (NRCan) Ultra-Rapid GPS products to serve as a short latency time-transfer tool to assist timing laboratories in operational maintenance of frequency standards and time scale dissemination. An automated data exchange and processing system has been set up to serve the international community for efficient, nearly real-time clock comparison and monitoring purposes.

Network time and frequency transfer with GNSS receivers located in time laboratories.

In this paper we investigate a possible network solution, similar to the IGS analysis center solutions, that can be easily managed by a network of timing institutes to solve for all the clock differences (in addition to other quantities) in a unique system to understand the feasibility and the advantages of this approach in time and frequency transfer. The investigation is based on a suite of global navigation satellite system (GNSS) software products that allows the users to perform a wide range of calculations and analyses related to GNSS, from the evaluation of performances at the user level to the computation of precise GNSS orbits and clocks, including the calculation of precise receiver coordinates. The time and frequency transfer capabilities of the network solution (named ODTS) are evaluated and compared with PPP solutions as well as to other time transfer results.

Further characterization of the time transfer capabilities of precise point positioning (PPP): the Sliding Batch Procedure.

In recent years, many national timing laboratories have installed geodetic Global Positioning System receivers together with their traditional GPS/GLONASS Common View receivers and Two Way Satellite Time and Frequency Transfer equipment. Many of these geodetic receivers operate continuously within the International GNSS Service (IGS), and their data are regularly processed by IGS Analysis Centers. From its global network of over 350 stations and its Analysis Centers, the IGS generates precise combined GPS ephemeredes and station and satellite clock time series referred to the IGS Time Scale. A processing method called Precise Point Positioning (PPP) is in use in the geodetic community allowing precise recovery of GPS antenna position, clock phase, and atmospheric delays by taking advantage of these IGS precise products. Previous assessments, carried out at Istituto Nazionale di Ricerca Metrologica (INRiM; formerly IEN) with a PPP implementation developed at Natural Resources Canada (NRCan), showed PPP clock solutions have better stability over short/medium term than GPS CV and GPS P3 methods and significantly reduce the day-boundary discontinuities when used in multi-day continuous processing, allowing time-limited, campaign-style time-transfer experiments. This paper reports on follow-on work performed at INRiM and NRCan to further characterize and develop the PPP method for time transfer applications, using data from some of the National Metrology Institutes. We develop a processing procedure that takes advantage of the improved stability of the phase-connected multi-day PPP solutions while allowing the generation of continuous clock time series, more applicable to continuous operation/monitoring of timing equipment.