RESUMO
UNLABELLED: Negative pressure isolation wards are essential infection control facilities against airborne transmissible diseases. Airborne infectious particles are supposed to be contained in the isolation room. However, negative pressure may break down by door-opening action or by human movement. Understanding the interzonal transport of airborne infectious particles in the isolation wards can aid the design and operation strategy of isolation facilities. In this work, the interzonal migration of airborne infectious particles by human movement was studied experimentally in an isolation ward. Artificial saliva solution with benign E. coli bacteria was aerosolized to simulate bacterium-laden infectious particles. The interzonal migration of aerosolized bacteria was characterized by biological air sampling. Less than 1% of airborne infectious particles were transported to the higher pressure zone when door was closed. With human movement, 2.7% of the particles were transported from the anteroom to the corridor. From high-to-low pressure zones, as much as 20.7% of airborne infectious particles were migrated. Only a minimal amount of particles was transported from the corridor to the positive pressure nurses' station. Infection risk of tuberculosis of the healthcare workers and other occupants in the isolation wards were also assessed based on the measured migration ratios. PRACTICAL IMPLICATIONS: Human movement is an important factor governing interzonal migration. It is the main cause of migration of airborne infectious particles to a relatively negative pressure zone. This study provides a set of experimentally obtained particle migration ratios by human movement. Other than serving as empirical data for further studies on the mechanics, these migration ratios can also be used to assess the infection risk for occupants in the isolation ward.
Assuntos
Microbiologia do Ar , Isolamento de Pacientes , Aerossóis/análise , Movimentos do Ar , Humanos , Medição de Risco , IncertezaRESUMO
Motivated by growing considerations of the scale, severity, and risks associated with human exposure to indoor particulate matter, this work reviewed existing literature to: (i) identify state-of-the-art experimental techniques used for personal exposure assessment; (ii) compare exposure levels reported for domestic/school settings in different countries (excluding exposure to environmental tobacco smoke and particulate matter from biomass cooking in developing countries); (iii) assess the contribution of outdoor background vs indoor sources to personal exposure; and (iv) examine scientific understanding of the risks posed by personal exposure to indoor aerosols. Limited studies assessing integrated daily residential exposure to just one particle size fraction, ultrafine particles, show that the contribution of indoor sources ranged from 19% to 76%. This indicates a strong dependence on resident activities, source events and site specificity, and highlights the importance of indoor sources for total personal exposure. Further, it was assessed that 10-30% of the total burden of disease from particulate matter exposure was due to indoor-generated particles, signifying that indoor environments are likely to be a dominant environmental factor affecting human health. However, due to challenges associated with conducting epidemiological assessments, the role of indoor-generated particles has not been fully acknowledged, and improved exposure/risk assessment methods are still needed, together with a serious focus on exposure control.
Assuntos
Aerossóis/análise , Poluição do Ar em Ambientes Fechados/análise , Exposição Ambiental , Aerossóis/efeitos adversos , Poluição do Ar em Ambientes Fechados/efeitos adversos , Humanos , Medição de RiscoRESUMO
Guidelines for heating, ventilation, and air-conditioning systems have been developed for different settings. However, there is a lack of up-to-date evidence providing concrete recommendations for the heating, ventilation, and air-conditioning systems of an isolation room, which is essential to appropriately guide infection control policies. To highlight the guidelines for heating, ventilation, and air-conditioning systems in isolation rooms to inform relevant stakeholders and policymakers. A systematic search was performed based on Joanna Briggs Methodology using five databases (CINAHL, Embase, Joanna Briggs Institute, Medline, and Web of Science) and websites. Eight articles published by government departments were included in this review. Most studies recommended controlled airflow without recirculation, 12 air changes per hour, high-efficiency particulate air filtrate to exhaust contaminated air from the airborne isolation room, humidity ≤60%, and temperature in the range of 18-30 °C. This review provides further evidence that there is a need for interdisciplinary collaborative research to quantify the optimum range for heating, ventilation, and air conditioning system parameters, considering door types, anterooms, and bed management, to effectively reduce the transmission of infection in isolation rooms.
Assuntos
Poluição do Ar em Ambientes Fechados , Calefação , Humanos , Ventilação/métodos , Ar Condicionado , Fenômenos Fisiológicos Respiratórios , Atenção à SaúdeRESUMO
Crystalline Co3O4 nanowire arrays freely supported on Ni foam are successfully synthesized using a template-free method. The effects of reaction time, concentration of reactants, and temperature on the morphology of the nanowires are studied. The results indicate that uniform Co3O4 nanowires could be synthesized at 90 degrees C, and a transformation of the samples' morphology from nanoparticles to nanowires to microrods is observed by controlling the concentration of the reactants. The well-ordered nanowires synthesized under the selected reaction conditions are composed of spinel Co3O4 with diameters of 500-580 nm and lengths of 6-8 microm. These nanowires show good catalytic activity for the ozone catalytic oxidation of toluene.
RESUMO
UNLABELLED: Infection risk assessment is very useful in understanding the transmission dynamics of infectious diseases and in predicting the risk of these diseases to the public. Quantitative infection risk assessment can provide quantitative analysis of disease transmission and the effectiveness of infection control measures. The Wells-Riley model has been extensively used for quantitative infection risk assessment of respiratory infectious diseases in indoor premises. Some newer studies have also proposed the use of dose-response models for such purpose. This study reviews and compares these two approaches to infection risk assessment of respiratory infectious diseases. The Wells-Riley model allows quick assessment and does not require interspecies extrapolation of infectivity. Dose-response models can consider other disease transmission routes in addition to airborne route and can calculate the infectious source strength of an outbreak in terms of the quantity of the pathogen rather than a hypothetical unit. Spatial distribution of airborne pathogens is one of the most important factors in infection risk assessment of respiratory disease. Respiratory deposition of aerosol induces heterogeneous infectivity of intake pathogens and randomness on the intake dose, which are not being well accounted for in current risk models. Some suggestions for further development of the risk assessment models are proposed. PRACTICAL IMPLICATIONS: This review article summarizes the strengths and limitations of the Wells-Riley and the dose-response models for risk assessment of respiratory diseases. Even with many efforts by various investigators to develop and modify the risk assessment models, some limitations still persist. This review serves as a reference for further development of infection risk assessment models of respiratory diseases. The Wells-Riley model and dose-response model offer specific advantages. Risk assessors can select the approach that is suitable to their particular conditions to perform risk assessment.
Assuntos
Relação Dose-Resposta a Droga , Infecções Respiratórias/transmissão , Algoritmos , Humanos , Modelos Teóricos , Medição de Risco/métodosRESUMO
Size distributions of expiratory droplets expelled during coughing and speaking and the velocities of the expiration air jets of healthy volunteers were measured. Droplet size was measured using the interferometric Mie imaging (IMI) technique while the particle image velocimetry (PIV) technique was used for measuring air velocity. These techniques allowed measurements in close proximity to the mouth and avoided air sampling losses. The average expiration air velocity was 11.7 m/s for coughing and 3.9 m/s for speaking. Under the experimental setting, evaporation and condensation effects had negligible impact on the measured droplet size. The geometric mean diameter of droplets from coughing was 13.5 µm and it was 16.0 µm for speaking (counting 1-100). The estimated total number of droplets expelled ranged from 947 to 2085 per cough and 112-6720 for speaking. The estimated droplet concentrations for coughing ranged from 2.4 to 5.2 cm-3 per cough and 0.004-0.223 cm-3 for speaking.
RESUMO
UNLABELLED: This study investigated the feasibility of using the spatial distribution of expiratory aerosols and the viability functions of airborne viruses to estimate exposures to airborne viruses in an indoor environment under imperfectly mixed condition. A method adopting this approach was tested in an air-conditioned hospital ward. Artificial coughs were produced by aerosolizing a simulated respiratory fluid containing a known concentration of benign bacteriophage. The bacteriophage exposures estimated on the basis of the spatial aerosol distributions and its viability function were in reasonable agreement with those measured directly by biological air sampling and culturing. The ventilation flow and coughing orientation were found to play significant roles in aerosol transport, leading to different spatial distribution patterns in bacteriophage exposure. Bacteriophage exposures decreased with lateral distance from the infector when the infector coughed vertically upward. In contrast, exposures were constant or even increased with distance in the case of lateral coughing. The possibility of incorporating the proposed exposure estimation into a dose-response model for infection risk assessment was discussed. The study has also demonstrated the potential application of viability functions of airborne viral pathogens in exposure assessment and infection risk analysis, which are often unavailable in literature for some important communicable diseases. PRACTICAL IMPLICATIONS: The proposed method makes use of the viability function of the virus and the spatial distribution of the expiratory aerosols for virus exposure estimation. Spatial differences in aerosol distribution and its influences on virus exposure in an air space can be determined. Variations in infectious dose with carrier aerosol size could also be considered. The proposed method may serve as a tool for further investigation of ventilation design and infection control in clinical or other indoor environments.
Assuntos
Aerossóis/análise , Poluição do Ar em Ambientes Fechados/análise , Bacteriófagos/isolamento & purificação , Bacteriófagos/fisiologia , Monitoramento Ambiental/métodos , Ar Condicionado , Surtos de Doenças/prevenção & controle , Monitoramento Ambiental/instrumentação , Humanos , Controle de Infecções , Serviço Hospitalar de Engenharia e Manutenção , Tamanho da Partícula , Medição de Risco , Ventilação , Replicação Viral/fisiologiaRESUMO
This study investigated the performance of a combined ozone and zeolite system in eliminating gaseous toluene which is a major contaminant in many industrial and indoor environments. The hypothesis that the removal of toluene by ozone can be substantially affected by confining the oxidation reaction in a zeolite structure was evaluated. The degradation of toluene seemed to be contributed by the active oxygen atom generated from the decomposition of ozone at the Lewis acid sites in the zeolite 13X. Air containing toluene levels at 1.5, 2 and 3 ppm was injected with ozone in the range of 0-6 ppm before being vented into a fixed amount of 3600 g zeolite 13X with 90 mm bed-length. The experimental results showed that the elimination rate of toluene was significantly enhanced when compared to using zeolite or ozone alone. In particular, over 90% of the 1.5 ppm toluene was removed when 6 ppm ozone was used at 40% relative humidity level. Deactivation of the zeolite 13X after a few hours of reactions under the current experimental conditions was probably due to the adsorbed water, carbon dioxide and the reaction by-products. The residue species left in the zeolite and the intermediate species in the exhaust gas stream were characterized by FT-IR, GC-MS and HP-LC methods, respectively. A distinctive peak of O atom attached to the Lewis acid site at 1380 cm(-1) was found in the FT-IR spectrum and trace amount of aldehydes was found to be the reaction by-products.
Assuntos
Poluentes Atmosféricos/química , Ozônio/química , Tolueno/química , Zeolitas/químicaRESUMO
It has been shown that the exposure to airborne particulate matter is one of the most significant environmental risks people face. Since indoor environment is where people spend the majority of time, in order to protect against this risk, the origin of the particles needs to be understood: do they come from indoor, outdoor sources or both? Further, this question needs to be answered separately for each of the PM mass/number size fractions, as they originate from different sources. Numerous studies have been conducted for specific indoor environments or under specific setting. Here our aim was to go beyond the specifics of individual studies, and to explore, based on pooled data from the literature, whether there are generalizable trends in routes of exposure at homes, schools and day cares, offices and aged care facilities. To do this, we quantified the overall 24h and occupancy weighted means of PM10, PM2.5 and PN - particle number concentration. Based on this, we developed a summary of the indoor versus outdoor origin of indoor particles and compared the means to the WHO guidelines (for PM10 and PM2.5) and to the typical levels reported for urban environments (PN). We showed that the main origins of particle metrics differ from one type of indoor environment to another. For homes, outdoor air is the main origin of PM10 and PM2.5 but PN originate from indoor sources; for schools and day cares, outdoor air is the source of PN while PM10 and PM2.5 have indoor sources; and for offices, outdoor air is the source of all three particle size fractions. While each individual building is different, leading to differences in exposure and ideally necessitating its own assessment (which is very rarely done), our findings point to the existence of generalizable trends for the main types of indoor environments where people spend time, and therefore to the type of prevention measures which need to be considered in general for these environments.
Assuntos
Poluição do Ar em Ambientes Fechados/análise , Monitoramento Ambiental , Instituição de Longa Permanência para Idosos , Material Particulado/análise , Instituições Acadêmicas , Local de Trabalho , Humanos , Tamanho da Partícula , Instalações PrivadasRESUMO
The present study reports a green synthesis method for preparing pure (free of fly ash) and ordered MCM-41 materials from coal fly ash at room temperature (25 degrees C) during 24 h of reaction. It was shown that the impurities in the coal fly ash were not detrimental to the formation of MCM-41 at the tested conditions. The influence of initial synthesis pH on material properties of calcined MCM-41 samples was investigated by various techniques such as XRF, XPS, XRD, FTIR, DR-UV-vis, solid state NMR, N2 physisorption, TG-DTA, SEM and TEM. The experimental results showed that the amount of trace elements such as Al, Na, Ti and Fe incorporated into the sample increased with synthesis pH value. More aluminum species were incorporated with tetrahedral coordination in the framework under a high pH value. The particle size of the sample decreased with the synthesis pH value. Samples synthesized at high pH values had a larger pore size and were more hydrothermally stable than those at low pH values. From thermal analysis, it was observed that the synthesized MCM-41 samples showed a high thermal stability. These properties made the synthesized MCM-41 suitable for further processing into more useful materials in a wide range of applications.
Assuntos
Carbono , Carvão Mineral , Conservação dos Recursos Naturais , Material Particulado , Dióxido de Silício/síntese química , Cinza de Carvão , Concentração de Íons de Hidrogênio , Espectroscopia de Ressonância Magnética , Microscopia Eletrônica de VarreduraRESUMO
Single phase chamfered-edge zeolite 4A samples in pure form with a high crystallinity were synthesized by applying step-change of synthesis temperature during hydrothermal treatment of coal fly ash. The calcium binding capacity of these zeolite 4A samples (prepared from coal fly ash) and the commercial detergent grade zeolite 4A were tested for usage as a detergent builder. The results show that these zeolite 4A samples behaved similarly as the commercial one in removing calcium ions during the washing cycle. Moreover, from the leaching tests (evaluation of toxicological safety), the results show that these zeolite 4A samples leached the same elements (Sb, As, Se and Tl) as the commercial one with the concentrations in the same order of magnitude. This shows that the toxicological effect of the coal fly ash converted zeolite 4A was not worse than that of the commercial sample. Finally, economic and environmental aspects of converting coal fly ash to useful products were discussed.
Assuntos
Carbono/química , Carvão Mineral , Detergentes/química , Material Particulado/química , Eliminação de Resíduos Líquidos/instrumentação , Eliminação de Resíduos Líquidos/métodos , Poluentes Químicos da Água/química , Zeolitas/química , Adsorção , Cálcio/química , Cinza de Carvão , Análise Custo-Benefício , Cristalização , Incineração , Metais Pesados , Microscopia Eletrônica de Varredura , Modelos Químicos , Eliminação de ResíduosRESUMO
The removal performance and the selectivity sequence of mixed metal ions (Co(2+), Cr(3+), Cu(2+), Zn(2+) and Ni(2+)) in aqueous solution were investigated by adsorption process on pure and chamfered-edge zeolite 4A prepared from coal fly ash (CFA), commercial grade zeolite 4A and the residual products recycled from CFA. The pure zeolite 4A (prepared from CFA) was synthesized under a novel temperature step-change method with reduced synthesis time. Batch method was employed to study the influential parameters such as initial metal ions concentration, adsorbent dose, contact time and initial pH of the solution on the adsorption process. The experimental data were well fitted by the pseudo-second-order kinetics model (for Co(2+), Cr(3+), Cu(2+) and Zn(2+) ions) and the pseudo-first-order kinetics model (for Ni(2+) ions). The equilibrium data were well fitted by the Langmuir model and showed the affinity order: Cu(2+) > Cr(3+) > Zn(2+) > Co(2+) > Ni(2+) (CFA prepared and commercial grade zeolite 4A). The adsorption process was found to be pH and concentration dependent. The sorption rate and sorption capacity of metal ions could be significantly improved by increasing pH value. The removal mechanism of metal ions was by adsorption and ion exchange processes. Compared to commercial grade zeolite 4A, the CFA prepared adsorbents could be alternative materials for the treatment of wastewater.
Assuntos
Carbono , Metais Pesados/farmacocinética , Poluentes Químicos da Água/isolamento & purificação , Zeolitas/farmacologia , Adsorção , Carvão Mineral , Cinza de Carvão , Conservação dos Recursos Naturais , Íons , Material ParticuladoRESUMO
Experiments were conducted in a continuous flow reactor at room temperature to evaluate the elimination of low-concentration toluene in the gas phase to verify if fly-ash products from biomass combustion in an ozonation system could be used in the removal of volatile organic compounds. The fly-ash products from pure biomass combustion (Ash(100)) demonstrated the highest ozonation activities upon the removal of low-concentration toluene (1.5 ppmv), followed by the fly-ash products from co-combustion (Ash(30)) and the coal combustion (Ash(0)). Kinetic experiments showed that the activation energy of the toluene elimination process was substantially reduced with the use of ozone and the reaction intermediates, such as formic acids, aldehydes, etc. Results also showed that the intermediates were reduced with increasing humidity level. The combined use of fly-ash products and zeolite 13X enhanced the removal of toluene to above 90% and suppressed the release of residual ozone and intermediates by holding them in the adsorbed phase.
Assuntos
Poluentes Atmosféricos/isolamento & purificação , Biomassa , Carbono , Material Particulado , Adsorção , Poluentes Atmosféricos/química , Aldeídos/química , Biotecnologia/métodos , Catálise , Carvão Mineral , Cinza de Carvão , Desenho de Equipamento , Formiatos/química , Umidade , Resíduos Industriais/análise , Cinética , Compostos Orgânicos/química , Ozônio/química , Temperatura , Tolueno/química , Zeolitas/químicaRESUMO
The performance of multimetal-(Cu, Cr, Zn, Ni, and Co)-ion-exchanged zeolite A prepared from both a commercial-grade sample and one produced from coal fly ash in methane emissions abatement was evaluated in this study. The ion-exchange process was used to load the metal ions in zeolite A samples. The methane conversion efficiency by the samples was studied under various parameters including the amount of metal loading (7.3-19.4 wt%), reaction temperature (25-500 degrees C), space velocity (8400-41 900 h(-1)), and methane concentration (0.5-3.2 vol %). At 500 degrees C, the original commercial-grade zeolite A catalyzed 3% of the methane only, whereas the addition of different percentages of metals in the sample enhanced the methane conversion efficiency by 40-85%. Greater methane conversion was observed by increasing the percentage of metals added to the zeolite even though the BET surface area of the zeolite consequently decreased. Higher percentage methane conversion over the multi-ion-exchanged samples was observed at lower space velocities indicating the importance of the mass diffusion of reactants and products in the zeolite. Compared to the multi-ion-exchanged zeolite A prepared from the commercial-grade zeolite, the one produced from coal fly ash demonstrated similar performances in methane emissions abatement, showing the potential use of this low cost recycled material in gaseous pollutant treatment.
Assuntos
Carbono/química , Carvão Mineral , Metano/isolamento & purificação , Material Particulado/química , Zeolitas/química , Cinza de Carvão , Troca Iônica , Oxirredução , Temperatura , TermodinâmicaRESUMO
The effects of passing ozone over different zeolite and MCM-41 materials to remove toluene were investigated. Different ozone-to-toluene ratios were used to evaluate the catalytic performance during ozonation. The micro- and meso-porous materials removed about 50% of the toluene via adsorption and another 20-40% was decomposed by ozonation, which was catalytically enhanced by the zeolite and MCM-41 materials. The catalytic reaction portion increased by using a higher ozone inlet concentration and it was further enhanced to around 50% with the use of more adsorbents or with longer residence times. Inside the porous structure of the material, ozone was either decomposed into active atomic oxygen for reactions or converted into oxygen for active site regeneration. The number of Lewis acid sites in the adsorbents for ozone decomposition and byproduct generation during the reactions limit the catalytic activities. Trace amounts of intermediates including aldehydes and organic acids were quantified in the ozonation process. A higher ozone inlet concentration helped to reduce intermediate species formation but it led to more residual ozone in the exhaust. The high adsorption capability of the zeolite and MCM-41 adsorbents could serve as reservoirs for suppressing the release of intermediate species to the exhaust.
Assuntos
Ozônio/química , Dióxido de Silício/química , Solventes/química , Tolueno/química , Zeolitas/química , Adsorção , Catálise , Humanos , PorosidadeRESUMO
Expiratory droplets and droplet nuclei can be pathogen carriers for airborne diseases. Their transport characteristics were studied in detail in two idealized floor-supply-type ventilation flow patterns: Unidirectional-upward and single-side-floor, using a multiphase numerical model. The model was validated by running interferometric Mie imaging experiments using test droplets with nonvolatile content, which formed droplet nuclei, ultimately, in a class-100 clean-room chamber. By comparing the droplet dispersion and removal characteristics with data of two other ceiling-supply ventilation systems collected from a previous work, deviations from the perfectly mixed ventilation condition were found to exist in various cases to different extent. The unidirectional-upward system was found to be more efficient in removing the smallest droplet nuclei (formed from 1.5 mum droplets) by air extraction, but it became less effective for larger droplets and droplet nuclei. Instead, the single-side-floor system was shown to be more favorable in removing these large droplets and droplet nuclei. In the single-side-floor system, the lateral overall dispersion coefficients for the small droplets and nuclei (initial size =45 mum) were about an order of magnitude higher than those in the unidirectional-upward system. It indicated that bulk lateral airflow transport in the single-side-floor system was much stronger than the lateral dispersion mechanism induced mainly by air turbulence in the unidirectional-upward system. The time required for the droplets and droplet nuclei to be transported to the exhaust vent or deposition surfaces for removal varied with different ventilation flow patterns. Possible underestimation of exposure level existed if the perfectly mixed condition was assumed. For example, the weak lateral dispersion in the unidirectional ventilation systems made expiratory droplets and droplet nuclei stay at close distance to the source leading to highly nonuniform spatial distributions. The distance between the source and susceptible patients became an additional concern in exposure analysis. Relative significance of the air-extraction removal mechanism was studied. This can have impact to the performance evaluation of filtration and disinfection systems installed in the indoor environment. These findings revealed the need for further development in a risk-assessment model incorporating the effect of different ventilation systems on distributing expiratory droplets and droplet nuclei nonuniformly in various indoor spaces, such as buildings, aircraft cabins, trains, etc.
Assuntos
Movimentos do Ar , Poluição do Ar em Ambientes Fechados , Expiração/fisiologia , Modelos Teóricos , Ventilação , Simulação por Computador , Reprodutibilidade dos TestesRESUMO
There have been few recent studies demonstrating a definitive association between the transmission of airborne infections and the ventilation of buildings. The severe acute respiratory syndrome (SARS) epidemic in 2003 and current concerns about the risk of an avian influenza (H5N1) pandemic, have made a review of this area timely. We searched the major literature databases between 1960 and 2005, and then screened titles and abstracts, and finally selected 40 original studies based on a set of criteria. We established a review panel comprising medical and engineering experts in the fields of microbiology, medicine, epidemiology, indoor air quality, building ventilation, etc. Most panel members had experience with research into the 2003 SARS epidemic. The panel systematically assessed 40 original studies through both individual assessment and a 2-day face-to-face consensus meeting. Ten of 40 studies reviewed were considered to be conclusive with regard to the association between building ventilation and the transmission of airborne infection. There is strong and sufficient evidence to demonstrate the association between ventilation, air movements in buildings and the transmission/spread of infectious diseases such as measles, tuberculosis, chickenpox, influenza, smallpox and SARS. There is insufficient data to specify and quantify the minimum ventilation requirements in hospitals, schools, offices, homes and isolation rooms in relation to spread of infectious diseases via the airborne route. PRACTICAL IMPLICATION: The strong and sufficient evidence of the association between ventilation, the control of airflow direction in buildings, and the transmission and spread of infectious diseases supports the use of negatively pressurized isolation rooms for patients with these diseases in hospitals, in addition to the use of other engineering control methods. However, the lack of sufficient data on the specification and quantification of the minimum ventilation requirements in hospitals, schools and offices in relation to the spread of airborne infectious diseases, suggest the existence of a knowledge gap. Our study reveals a strong need for a multidisciplinary study in investigating disease outbreaks, and the impact of indoor air environments on the spread of airborne infectious diseases.
Assuntos
Microbiologia do Ar/normas , Doenças Transmissíveis/transmissão , Controle de Infecções/normas , Ventilação/normas , Movimentos do Ar , Infecção Hospitalar , HumanosRESUMO
Dispersion characteristics of expiratory aerosols were investigated in an enclosure with two different idealized airflow patterns: the ceiling-return and the unidirectional downward. A multiphase numerical model, which was able to capture the polydispersity and evaporation features of the aerosols, was adopted. Experiments employing optical techniques were conducted in a chamber with downward airflow pattern to measure the dispersion of aerosols. Some of the numerical results were compared with the chamber measurement results. Reasonable agreement was found. Small aerosols (initial size Assuntos
Aerossóis
, Movimentos do Ar
, Modelos Teóricos
, Poluição do Ar em Ambientes Fechados
, Expiração
, Ventilação