Use of the dummy approach for the synthesis of ion imprinted polymers with Ni(II) or Zn(II) as template ion for the solid-phase extraction of Cu(II).

There is a strong interest in monitoring copper in environmental waters, but its direct analysis suffers from strong matrix interferences. This is why, a sample pretreatment based on solid-phase extraction (SPE) is often used but conventional sorbents usually lack specificity. It is overcome with ion-imprinted polymers (IIPs). This work evaluates for the first time the use of the dummy approach for the synthesis of Cu(II)-targeting IIPs. Two analog ions Ni(II) and Zn(II) were tested as templates and the resulting IIPs were packed in SPE cartridges. The SPE procedure was designed by optimizing a washing step following the sample percolation, to eliminate the interfering ions retained on the IIP by non-specific interactions. To optimize the washing step, solutions at different pH or containing tris(hydroxymethyl)aminomethane as a complexing agent at different concentrations were tested and combined. Zn-IIP appeared more promising than Ni-IIP, showing excellent specificity and a high selectivity. Its retention capacity was determined to be 100 µg/g, and different isotherm models were evaluated to fit with the adsorption data. Finally, applications to mineral and sea waters were successfully completed and led to high and repeatable extraction recoveries for Cu(II) (88 ± 1% and 83 ± 3%, respectively).

Development of setups for real-time analysis of the effluent of a microreactor by mass spectrometry.

Monitoring a synthesis reaction in real time could allow not only the detection of the intermediates involved in the synthesis, to better understand its mechanisms, but also the impurities. Spectroscopic methods could be performed but are not so performant when analyzing complex mixtures and could require specific properties for the detection of the molecules of interest, the presence of a chromophore moiety for example. Mass spectrometry (MS) may overcome these limitations and is able to reach the accuracy and sensitivity required to efficiently detect, quantify, identify, and characterize the reagents and species produced during the synthesis. This is why the hyphenation of a microreactor with MS has already allowed synthesis processes to be monitored, but most of the time it targets a specific reaction or compounds and involves solvents compatible with MS. In this study, a universal setup for the hyphenation of a microreactor with MS and based on two valves has been developed. This two-valve setup has proven itself for the analysis of molecules of different nature and hydrophilicity, soluble in a large number of solvents even in non-MS-compatible ones. The developed setup evidenced a good repeatability and a linear response for the detection of the studied compounds. In addition, the dilution step included in the two-valve setup allows the MS monitoring of compounds initially synthesized at different concentrations. Finally, it was successfully used to study an amination reaction allowing the detection of the reaction products in 4 min with good repeatability as RSD values of MS signals were lower than 17%.

Molecularly imprinted polymers in miniaturized extraction and separation devices.

Molecularly imprinted polymers are highly selective and cost-effective materials, which have attracted significant interest in various areas such as sample pretreatment and chromatographic and electrophoretic separations. This review aims to present the state of the art concerning the miniaturization of these materials in order to meet the societal demand for reliable, fast, cheap, and solvent/sample saving analyses. The polymerization route specificities for the production of miniaturized molecularly imprinted polymers in capillaries or chip channels, such as open tubular, packed particles, magnetic nanoparticles, and in situ imprinted monoliths, are investigated. Their performances as selective supports in solid phase extraction and as stationary phases in electrochromatography and liquid chromatography, as well as their possible perspectives are discussed.

Analysis of the human chorionic gonadotropin protein at the intact level by HILIC-MS and comparison with RPLC-MS.

In the present work, the human chorionic gonadotropin (hCG) hormone was characterized for the first time by hydrophilic interaction liquid chromatography (HILIC) coupled to high-resolution (HR) quadrupole/time-of-flight (qTOF) mass spectrometry (MS) at the intact level. This heterodimeric protein, consisting of two subunits (hCGα and hCGß), possesses 8 potential glycosylation sites leading to a high number of glycoforms and has a molecular weight of about 35 kDa. The HILIC conditions optimized in a first paper but using UV detection were applied here with MS for the analysis of two hCG-based drugs, a recombinant hCG and a hCG isolated from the urine of pregnant women. An amide column (150 × 2.1 mm, 2.6 µm, 150 Å), a mobile phase composed of acetonitrile and water both containing 0.1% of trifluoroacetic acid, and a temperature of 60 °C were used. The gradient was from 85 to 40% ACN in 30 min. The use of TFA that had been shown to be necessary for the separation of glycoforms caused, as expected, an ion suppression effect in MS that was partially overcome by increasing the amount of protein injected (2 µL at 1 mg mL-1) and reducing the detection m/z range (from 1500 to 300). These conditions allowed the detection of different glycoforms of hCGα. The performance of the HILIC-HRMS method was compared with that previously obtained in RPLC-HRMS in terms of the number of detected glycoforms, selectivity, and sensitivity. The complementarity and orthogonality of the HILIC and RP modes for the analysis of hCG at the intact level were demonstrated.

Identification and semi-relative quantification of intact glycoforms by nano-LC-(Orbitrap)MS: application to the α-subunit of human chorionic gonadotropin and follicle-stimulating hormone.

Human chorionic gonadotropin (hCG) and follicle-stimulating hormone (FSH) belong to the family of glycoprotein polypeptide hormones called gonadotropins. They are heterodimers sharing the α-subunit structure that has 2 N-glycosylation sites. A method based on nano-reversed-phase liquid chromatography coupled to high-resolution mass spectrometry with an Orbitrap analyzer was developed for the first time to characterize the glycosylation state of the α-subunit at the intact level. A recombinant hCG-based drug, Ovitrelle®, was analyzed. This method combined with an appropriate data treatment allowed the detection of not only the major isoforms but also the minority ones with a high mass accuracy. More than 30 hCGα glycoforms were detected without overlapping of the isotopic patterns. The figures of merit of the method were assessed. The relative standard deviations (RSDs) of the retention time ranged between 0.1 and 6.08% (n = 3), with an average of 0.4%. The RSDs of the peak area measured on the extracted ion chromatogram of each glycoform are below 38% (n = 3), with an average of 16%, thus allowing semi-relative quantification. The ability to accurately profile glycosylated variants of hCGα was next demonstrated by comparing qualitatively and semi-quantitatively 3 batches of Ovitrelle®. The method was also used to analyze 3 batches of a recombinant FSH-based drug, Puregon®, and 30 FSHα glycoforms were detected and semi-quantified. This demonstrates the high potential of this method for fast quality control or comparison of the glycosylation of glycoprotein-based pharmaceutical preparations. Graphical abstract.

Interinstrumental transfer of a fast short-end injection capillary electrophoresis method: Application to the separation of niobium, tantalum, and their substituted ions.

The interinstrumental transfer of a short-end CE method was studied. A model separation of the hexameric forms of niobium, tantalum, and their substituted ions (Nb6-x Tax with 0 ≤ x ≤ 6) was selected as test case. The method was first optimized on a Beckman instrument and in a second step transferred to an Agilent instrument. The transfer needed updated guidelines that tackled differences in effective capillary length, 8.5 (Agilent) versus 10 cm (Beckman), because of instrumental different capillary cartridges. Differences in effective length lead to migration time and separation efficiency inequalities, illustrated by a decrease in resolution between the substituted ions. The difference in effective length was overcome by adapting the lift offset parameter of the Agilent instrument. The lift offset default setting is 4 mm and by increasing this parameter both the inlet and outlet lifts are lowered and thus the detection window can be displaced and consequently the effective length was increased. The decrease in effective length difference and the effect on the separation efficiency was investigated and led finally to a restored separation of the substituted ions. The adaptation of the lift offset parameter during short-end injection methods was added to earlier developed guidelines to facilitate interinstrumental method transfer of CE methods.

Regulation of Catalytic and Non-catalytic Functions of the Drosophila Ste20 Kinase Slik by Activation Segment Phosphorylation.

Protein kinases carry out important functions in cells both by phosphorylating substrates and by means of regulated non-catalytic activities. Such non-catalytic functions have been ascribed to many kinases, including some members of the Ste20 family. The Drosophila Ste20 kinase Slik phosphorylates and activates Moesin in developing epithelial tissues to promote epithelial tissue integrity. It also functions non-catalytically to promote epithelial cell proliferation and tissue growth. We carried out a structure-function analysis to determine how these two distinct activities of Slik are controlled. We find that the conserved C-terminal coiled-coil domain of Slik, which is necessary and sufficient for apical localization of the kinase in epithelial cells, is not required for Moesin phosphorylation but is critical for the growth-promoting function of Slik. Slik is auto- and trans-phosphorylated in vivo. Phosphorylation of at least two of three conserved sites in the activation segment is required for both efficient catalytic activity and non-catalytic signaling. Slik function is thus dependent upon proper localization of the kinase via the C-terminal coiled-coil domain and activation via activation segment phosphorylation, which enhances both phosphorylation of substrates like Moesin and engagement of effectors of its non-catalytic growth-promoting activity.

Analysis of underivatized cellodextrin oligosaccharides by capillary electrophoresis with direct photochemically induced UV-detection.

This work focuses on the development of a CE method allowing, for the first time, the simultaneous separation of the underivatized first seven cellodextrin oligomers (glucose, cellobiose, cellotriose, cellotetraose, cellopentaose, cellohexaose, and celloheptaose), with a view to analyze the hydrolysates obtained after partial acid depolymerization of nitrocellulose, and eight carbohydrates (ribose, xylose, fructose, mannose, galactose, maltose, lactose, and sucrose), which might be potential interfering compounds in explosives samples. Separation was achieved with a highly alkaline BGE containing sodium chloride and direct mid-UV-absorbance detection was performed after photo-oxidation in the detection window. EOF was reversed to speed up the analysis using a dynamic capillary coating by hexadimethrine bromide. A central composite design was carried out to determine the effects of BGE conductivity and sodium hydroxide concentration on resolutions between neighboring peaks, and analysis time. A desirability analysis on modeled responses was applied to maximize resolutions and to minimize analysis time. The simultaneous analysis in 20 min total runtime of the 15 carbohydrates plus internal reference (naphthalene sulfonate) was carried out at 25°C with a BGE composed of 77.4 mM NaOH and 183 mM NaCl to adjust the conductivity at the optimum value. Finally, the resolution robustness was checked. This new method should also be of interest to monitor food and nonfood crop products.

Capillary and microchip electrophoretic analysis of polycyclic aromatic hydrocarbons.

Polycyclic aromatic hydrocarbons (PAHs) are ubiquitous contaminants which can reach the environment and food in different ways. Because of their high toxicity, two international regulatory institutions, the US Environmental Protection Agency and the European Food Safety Authority, have classified PAHs as priority pollutants, generating an important demand for the detection and identification of PAHs. Thus, sensitive, fast, and cheap methods for the analysis of PAHs in environmental and food samples are urgently needed. Within this context, electrophoresis, in capillary or microchip format, displays attractive features. This review presents and critically discusses the published literature on the different approaches to capillary and microchip electrophoresis analysis of PAHs.

Salt assisted liquid-liquid extraction combined with dispersive liquid-liquid microextraction for the determination of 24 regulated polycyclic aromatic hydrocarbons in human serum.

Polycyclic aromatic hydrocarbons (PAHs) are persistent organic pollutants of great concern due to their carcinogenicity and mutagenicity. Their determination in human serum, particularly in at-risk populations, is necessary but difficult because they are distributed over a wide range of polarity and are present at trace level. A new method combining salting-out assisted liquid-liquid extraction (SALLE) and dispersive liquid-liquid microextraction with solidification of floating organic drop (DLLME-SFO) adapted to a reduced volume of sample (100 µl) was developed to determine 24 PAHs in human serum. Some key parameters of DLLME-SFO (volume of extraction solvent, ratio of extraction/dispersive solvent volumes, and salt addition) were first studied by applying it to spiked pure water. For its application to serum, a sample treatment step involving SALLE was optimized in terms of nature and content of salts and applied upstream of DLLME-SFO. It was applied to the extraction of 24 regulated PAHs from spiked serum followed by an analysis by liquid chromatography coupled with UV and fluorescence detection. The extraction recoveries ranged from 48.2 and 116.0 % (relative standard deviations: 2.0-14.6 %, n=5-9), leading to limits of quantification of PAHs in human serum from 0.04 to 1.03 µg/L using fluorescence detection and from 10 to 40 µg/L using UV detection. This final method combining SALLE and DLLME-SFO showed numerous advantages such as no evaporation step, high efficiency and low solvent-consumption and will be useful for monitoring PAHs in low volumes of serum.

Characterization of Concanavalin A-based lectin sorbents for the extraction of the human chorionic gonadotropin glycoforms prior to analysis by nano liquid chromatography-high resolution mass spectrometry.

Human chorionic gonadotropin (hCG) is constituted of the hCGα and hCGß subunits and is a highly glycosylated protein. Affinity supports based on immobilized Concanavalin A (Con A) lectin were used in solid phase extraction (SPE) to fractionate the hCG glycoforms according to their glycosylation state. For the first time, the lectin SPE fractions were off-line analysed by a nano liquid chromatography - high-resolution mass spectrometry (nanoLC-HRMS) method keeping the glycoforms intact. For this, home-made Con A sorbents were prepared by immobilizing lectin on Sepharose with a mean grafting yield of 98.2% (relative standard deviation (RSD) of 3.5%, n = 15). A capacity of about 100 µg of purified urinary hCG (uhCG) per ml of sorbent, grafted with a density of 10 mg of Con A per ml, was estimated. Average extraction yields of around 60% for both hCGα and hCGß glycoforms were obtained after optimization of the extraction protocol. Intra- and inter-assay evaluation led to average RSD values of around 10%, indicating a repeatable extraction procedure. Similar results were obtained with commercial Con A-based sorbents but only after their 3rd use or after an extensive pre-conditioning step. Finally, the Con A SPE led to the fractionation of some glycoforms of uhCG, allowing the detection of an hCGα glycoform with two tetra-antennary N-glycans that couldn't be detected by direct analysis in nanoLC-HRMS without Con A SPE. Regarding a recombinant hCG, a fractionation was also observed leading to the detection of unretained hCGα glycoforms with tri-antennary N-glycans. Therefore, the combination of lectin SPE with intact protein analysis by nanoLC-HRMS can contribute to a more detailed glycosylation characterization of the hCG protein.

Influence of high-conductivity buffer composition on field-enhanced sample injection coupled to sweeping in CE.

The aim of this work was to clarify the mechanism taking place in field-enhanced sample injection coupled to sweeping and micellar EKC (FESI-Sweep-MEKC), with the utilization of two acidic high-conductivity buffers (HCBs), phosphoric acid or sodium phosphate buffer, in view of maximizing sensitivity enhancements. Using cationic model compounds in acidic media, a chemometric approach and simulations with SIMUL5 were implemented. Experimental design first enabled to identify the significant factors and their potential interactions. Simulation demonstrates the formation of moving boundaries during sample injection, which originate at the initial sample/HCB and HCB/buffer discontinuities and gradually change the compositions of HCB and BGE. With sodium phosphate buffer, the HCB conductivity increased during the injection, leading to a more efficient preconcentration by staking (about 1.6 times) than with phosphoric acid alone, for which conductivity decreased during injection. For the same injection time at constant voltage, however, a lower amount of analytes was injected with sodium phosphate buffer than with phosphoric acid. Consequently sensitivity enhancements were lower for the whole FESI-Sweep-MEKC process. This is why, in order to maximize sensitivity enhancements, it is proposed to work with sodium phosphate buffer as HCB and to use constant current during sample injection.

Development of ion-imprinted polymers for the selective extraction of Cu(II) ions in environmental waters.

Several ion-imprinted polymers (IIPs) were synthesized via bulk polymerization with Cu(II) as template ion, methacrylic acid as functional monomer, ethylene glycol dimethacrylate as crosslinking agent, and azobisisobutyronitrile as initiator in acetonitrile or methanol as porogen solvent. Non-imprinted polymers (NIPs) were similarly synthesized but without Cu(II). After grounding and sieving, the template ions were removed from IIPs particles through several cycles of elimination in 3 M HCl. All NIPs were equally subjected to this acid treatment with the exception of one NIP, called unwashed NIP. The resulting IIP/NIP particles were packed in solid phase extraction (SPE) cartridges for characterization. The SPE protocol was designed by optimizing a washing step following the sample percolation to eliminate potential interfering ions prior to the elution of Cu(II), all fractions analyzed by inductively coupled plasma mass spectrometry. The best IIP showed a high specificity (recovery of Cu(II) vs. interfering ions) and a good selectivity (retention on IIP vs. NIP). Its adsorption capacity was determined to be 63 µg g-1. Then, a volume of 50 mL was percolated with 30 mg of IIP, thus giving rise to an enrichment factor of 24. Finally, applications to real samples (mineral and sea waters) were successfully performed. In addition, Brunauer-Emmett-Teller analyses showed that the surface area of the washed NIP was almost double that of the unwashed one (140.70 vs. 74.49 m2 g-1), demonstrating for the first time that the post-treatment of a NIP after its synthesis may have a significant impact on its porous structure, and thus need to be more precisely detailed by authors in the future papers.

A chemometric approach for the elucidation of the parameter impact in the hyphenation of field-enhanced sample injection and sweeping in capillary electrophoresis.

The aim of this work was to elucidate the impacts of parameters influencing cation-selective exhaustive injection coupled to sweeping and micellar electrokinetic chromatography (MEKC). A chemometric approach using cationic compounds, acidic conditions (phosphate buffer, pH 2.3) and polyacrylamide-coated capillaries to suppress electroosmotic flow were used. It was demonstrated that the water plug was not useful because of long electrokinetic injections. If conductivity of the high conductivity buffer (HCB) and the HCB to sample conductivity ratio are sufficiently high (>1.66 S/m and >30, respectively), variations of HCB conductivity do not impact sensitivity. The length of the HCB must be long enough so that the most mobile cation remains stacked in this zone for a given injection time. SDS concentration should be as high as possible (the maximum concentration is dictated by MEKC, here 90 mM), so sensitivity is not impacted. We have shown analytes can be lost after electrokinetic injection, when the polarity of the voltage is reversed. Introducing a plug of micellar electrolyte before polarity reversal avoids these losses. Following these recommendations only injection time and sample conductivity impacted sensitivity enhancement. Sample conductivity had to be the lowest as possible and controlled in real case analyses to obtain repeatable enrichment factors.

On the use of response surface strategy to elucidate the electrophoretic migration of carbohydrates and optimize their separation.

This paper focuses on the optimization with a design of experiments of a new CE method for the simultaneous separation of four carbohydrates of interest (fructose, glucose, lactose, and sucrose) and five potentially interfering carbohydrates (ribose, xylose, maltose, mannose, and galactose) with a highly alkaline separation electrolyte for subsequent applications to food, beverage, forensic, or pharmaceutical samples. First, the factors that potentially affect the carbohydrate migration were identified: NaOH concentration in the separation electrolyte, separation temperature, and separation electrolyte conductivity. A central composite design was then carried out to determine and model the effects of these three factors on normalized migration times and separation efficiency. From the model, an optimization of the separation was carried out using a desirability analysis based on resolutions between adjacent peaks and analysis time. The optimum conditions obtained were a separation electrolyte composed of 98 mM NaOH and 120 mM NaCl to adjust the conductivity at 4.29 S/m and a separation temperature fixed at 26.5°C. Finally, these conditions were experimentally confirmed and the robustness of the obtained separation was checked.

226Ra and 137Cs determination by inductively coupled plasma mass spectrometry: state of the art and perspectives including sample pretreatment and separation steps.

Achieving precise and accurate quantification of radium (226Ra) and cesium (137Cs) by inductively coupled plasma mass spectrometry (ICP-MS) is of particular interest in the field of radiological monitoring and more widely in environmental and biological sciences. However, the accuracy and sensitivity of the quantification depend on the analytical strategy implemented. Eliminating interferences during the sample handling step and/or during the analysis step is critical since presence of matrix elements can lead to spectral and non-spectral interferences in ICP-MS. Consequently, before the ICP-MS analysis, multiple sample preparation approaches have been applied to purify and/or pre-concentrate environmental and biological samples containing radium and cesium through years, such as (co)-precipitation, solid phase extraction (SPE) or dispersive SPE (dSPE). Separation steps using liquid chromatography and capillary electrophoresis can also be useful in complement with the abovementioned sample preparation techniques. The most attractive sample handling technique remains SPE but efficiency of the extraction procedures is currently limited by sorbent specificity. Indeed, with the recent advances in ICP-MS instrumentation, it becomes indispensable to eliminate residual interferences and improve sensitivity. It is in this direction that it will be possible to meet analytical challenges, e.g. analyzing radium and cesium at concentrations below the pg L-1 range in complex matrices of small volumes, as they are found for instance in pore waters or in biological samples. Development of new innovative sorbents based for example on hybrid and nanostructured materials has been reported with the aim of enhancing sorbent specificity and/or capacity. In the present review, the performances of the different analytical approaches are discussed, followed by an overview of applications.

New avenue for mid-UV-range detection of underivatized carbohydrates and amino acids in capillary electrophoresis.

Capillary electrophoresis (CE) appeared as an interesting alternative to chromatographic methods for carbohydrate analysis, but it can be difficult to implement, because of the lack of easily ionizable functions and chromophore groups. Recently, a promising method was proposed by Rovio et al. for the CE separation under extremely high alkaline conditions of neutral carbohydrates under their alcoholate form and their direct UV detection [Rovio et al. Electrophoresis 2007, 28, 3129-3135; and Rovio et al. J. Chromatogr. A 2008, 1185, 139-144], which is claimed to be due to the absorption of enediolate at 270 nm. Even so, most of the detected compounds in Rovio's paper (for example, sucrose) cannot give such enediolate, lacking a carbonyl group. In this work, a deeper insight was paid to the understanding of detection mechanism. In effect, unusual detection phenomena were observed in comparing reducing and nonreducing carbohydrate behaviors, which pointed to the existence of photochemical reactions in the detection window. A more systematic study of the influence of many parameters (carbohydrate nature, electrolyte pH, residence time in the detection window, and capillary diameter) was undertaken. In addition to this, most of this work was performed under cathodic (reversed) electro-osmotic flow conditions (using Polybrene-modified capillaries), to obtain much faster separations than under Rovio's conditions. This study also opens up new avenues for the detection in mid-UV range of non-UV-absorbing compounds bearing reducing moieties, such as amino acids.

Capillary electrophoresis analysis of inorganic cations in post-blast residue extracts applying a guanidinium-based electrolyte and bilayer-coated capillaries.

A new CE method was developed for the identification and quantitation of inorganic cations in post-blast residues. The simultaneous analysis in 20 min total runtime of eight cations in post-blast residues (ammonium, potassium, monomethylammonium, calcium, sodium, magnesium, strontium), plus lithium cation as the internal reference, was carried out with a BGE involving a non-CMR (carcinogenic, mutagenic, and harmful to reproduction) chromophore (guanidinium cation) and a double-layer modified capillary (hexadimethrine bromide/polyvinylsulfonate). A study of UV detection conditions using guanidinium ion as the probe led us to set the analysis and reference wavelengths and their associated bandwidths as well as the probe concentration fixed at 15 mM. The successive multiple ionic-polymer layer approach limited the cation adsorption on capillary wall and improved the EOF stability. These caused a significant improvement in method repeatability. Intermediate precisions were 2.4% for corrected areas and 1.3% for normalized migration times. Limits of detection close to 1 mg/L for all cations were obtained. The matrix effects were studied with chemometric approach for different matrices representative of those collected after explosion. Tests with blank matrix extracts of soil, cloth, and with simulated matrix extract containing 800 mg/L Ca²âº and 500 mg/L Fe²âº were carried out and no significant matrix effects were observed. Finally, analyses of real residues collected after cash dispenser and homemade firework explosions demonstrate excellent correlation between the CE results and those obtained with the ion chromatography method used routinely.

Recent Advances in Lectin-Based Affinity Sorbents for Protein Glycosylation Studies.

Glycosylation is one of the most significant post-translational modifications occurring to proteins, since it affects some of their basic properties, such as their half-life or biological activity. The developments in analytical methodologies has greatly contributed to a more comprehensive understanding of the quantitative and qualitative characteristics of the glycosylation state of proteins. Despite those advances, the difficulty of a full characterization of glycosylation still remains, mainly due to the complexity of the glycoprotein and/or glycopeptide mixture especially when they are present in complex biological samples. For this reason, various techniques that allow a prior selective enrichment of exclusively glycosylated proteins or glycopeptides have been developed in the past and are coupled either on- or off- line with separation and detection methods. One of the most commonly implemented enrichment methods includes the use of lectin proteins immobilized on various solid supports. Lectins are a group of different, naturally occurring proteins that share a common characteristic, which concerns their affinity for specific sugar moieties of glycoproteins. This review presents the different formats and conditions for the use of lectins in affinity chromatography and in solid phase extraction, including their use in dispersive mode, along with the recent progress made on either commercial or home-made lectin-based affinity sorbents, which can lead to a fast and automated glycosylation analysis.