Redox centers evolution in phospho-olivine type (LiFe0.5Mn0.5 PO4) nanoplatelets with uniform cation distribution.

In phospho-olivine type structures with mixed cations (LiM1M2PO4), the octahedral M1 and M2 sites that dictate the degree of intersites order/disorder play a key role in determining their electrochemical redox potentials. In the case of LiFexMn1-xPO4, for example, in micrometer-sized particles synthesized via hydrothermal route, two separate redox centers corresponding to Fe(2+)/Fe(3+) (3.5 V vs Li/Li(+)) and Mn(2+)/Mn(3+) (4.1 V vs Li/Li(+)), due to the collective Mn-O-Fe interactions in the olivine lattice, are commonly observed in the electrochemical measurements. These two redox processes are directly reflected as two distinct peak potentials in cyclic voltammetry (CV) and equivalently as two voltage plateaus in their standard charge/discharge characteristics (in Li ion batteries). On the contrary, we observed a single broad peak in CV from LiFe0.5Mn0.5PO4 platelet-shaped (∼10 nm thick) nanocrystals that we are reporting in this work. Structural and compositional analysis showed that in these nanoplatelets the cations (Fe, Mn) are rather homogeneously distributed in the lattice, which is apparently the reason for a synergetic effect on the redox potentials, in contrast to LiFe0.5Mn0.5PO4 samples obtained via hydrothermal routes. After a typical carbon-coating process in a reducing atmosphere (Ar/H2), these LiFe0.5Mn0.5PO4 nanoplatelets undergo a rearrangement of their cations into Mn-rich and Fe-rich domains. Only after such cation rearrangement (via segregation) in the nanocrystals, the redox processes evolved at two distinct potentials, corresponding to the standard Fe(2+)/Fe(3+) and Mn(2+)/Mn(3+) redox centers. Our experimental findings provide new insight into mixed-cation olivine structures in which the degree of cations mixing in the olivine lattice directly influences the redox potentials, which in turn determine their charge/discharge characteristics.

Etched colloidal LiFePO4 nanoplatelets toward high-rate capable Li-ion battery electrodes.

LiFePO4 has been intensively investigated as a cathode material in Li-ion batteries, as it can in principle enable the development of high power electrodes. LiFePO4, on the other hand, is inherently "plagued" by poor electronic and ionic conductivity. While the problems with low electron conductivity are partially solved by carbon coating and further by doping or by downsizing the active particles to nanoscale dimensions, poor ionic conductivity is still an issue. To develop colloidally synthesized LiFePO4 nanocrystals (NCs) optimized for high rate applications, we propose here a surface treatment of the NCs. The particles as delivered from the synthesis have a surface passivated with long chain organic surfactants, and therefore can be dispersed only in aprotic solvents such as chloroform or toluene. Glucose that is commonly used as carbon source for carbon-coating procedure is not soluble in these solvents, but it can be dissolved in water. In order to make the NCs hydrophilic, we treated them with lithium hexafluorophosphate (LiPF6), which removes the surfactant ligand shell while preserving the structural and morphological properties of the NCs. Only a roughening of the edges of NCs was observed due to a partial etching of their surface. Electrodes prepared from these platelet NCs (after carbon coating) delivered a capacity of ∼ 155 mAh/g, ∼ 135 mAh/g, and ∼ 125 mAh/g, at 1 C, 5 C, and 10 C, respectively, with significant capacity retention and remarkable rate capability. For example, at 61 C (10.3 A/g), a capacity of ∼ 70 mAh/g was obtained, and at 122 C (20.7 A/g), the capacity was ∼ 30 mAh/g. The rate capability and the ease of scalability in the preparation of these surface-treated nanoplatelets make them highly suitable as electrodes in Li-ion batteries.

Investigating how nitrogen nutrition and pruning impacts on CBD and THC concentration and plant biomass of Cannabis sativa.

Precise crop fertilization requires an in-depth understanding of plant uptake and utilisation to optimise sustainable production. This study investigated the influence of nitrogen (N) nutrition and pruning on the cannabinoid concentrations and biomass of a commercial cannabis cultivar; the rationale for this study is how N supply and pruning affect cannabinoid yields and concentration in a commercial setting. Clones of a Cannabis sativa L. (CBD-type) were grown in a controlled-environment glasshouse in pots with coarse sand. After five weeks of vegetative growth under 210 mg/L N and an 18 h light regime, rates of 30, 60, 210, and 500 mg/L N were applied to plants for twelve weeks and a light regime set at 12 h. Double stem pruning was applied as an additional treatment to investigate efficacy on biomass increase. Biomass, N concentrations, and cannabinoid concentrations were measured after the final harvest. Pruning treatment did not increase cannabinoid concentrations or affect biomass. It was coincidentally found that plants on the glasshouse edge with higher exposure to sunlight developed more biomass and higher cannabinoid concentrations. Only biomass in leaves was increased significantly via higher nitrogen nutrition. Cannabinoid concentration, as well as cannabinoid yield per plant were decreased with the increase in N supply. High rates of fertilizer are not recommended because of reduced cannabinoid concentration and biomass yield: the ideal N supply is likely to be between 60 and 210 mg/L. This research will benefit growers and advisors in understanding the complexity of effects of nitrogen fertiliser and pruning practices on plant biomass and secondary metabolite production in medicinal cannabis.

Relevance of LiPF6 as Etching Agent of LiMnPO4 Colloidal Nanocrystals for High Rate Performing Li-ion Battery Cathodes.

LiMnPO4 is an attractive cathode material for the next-generation high power Li-ion batteries, due to its high theoretical specific capacity (170 mA h g(-1)) and working voltage (4.1 V vs Li(+)/Li). However, two main drawbacks prevent the practical use of LiMnPO4: its low electronic conductivity and the limited lithium diffusion rate, which are responsible for the poor rate capability of the cathode. The electronic resistance is usually lowered by coating the particles with carbon, while the use of nanosize particles can alleviate the issues associated with poor ionic conductivity. It is therefore of primary importance to develop a synthetic route to LiMnPO4 nanocrystals (NCs) with controlled size and coated with a highly conductive carbon layer. We report here an effective surface etching process (using LiPF6) on colloidally synthesized LiMnPO4 NCs that makes the NCs dispersible in the aqueous glucose solution used as carbon source for the carbon coating step. Also, it is likely that the improved exposure of the NC surface to glucose facilitates the formation of a conductive carbon layer that is in intimate contact with the inorganic core, resulting in a high electronic conductivity of the electrode, as observed by us. The carbon coated etched LiMnPO4-based electrode exhibited a specific capacity of 118 mA h g(-1) at 1C, with a stable cycling performance and a capacity retention of 92% after 120 cycles at different C-rates. The delivered capacities were higher than those of electrodes based on not etched carbon coated NCs, which never exceeded 30 mA h g(-1). The rate capability here reported for the carbon coated etched LiMnPO4 nanocrystals represents an important result, taking into account that in the electrode formulation 80% wt is made of the active material and the adopted charge protocol is based on reasonable fast charge times.