A very rare vascular complication of the Edwards expandable eSheath during transcatheter aortic valve replacement.

Transcatheter aortic valve replacement (TAVR) has revolutionized the management of severe symptomatic aortic valve stenosis. TAVR is now indicated as an alternative to surgical replacement in a wide risk profile ranging from high to low surgical risk. Although vascular complications have decreased in frequency over time, with the introduction of lower profile delivery systems and sheaths, they remain one of the most frequently encountered and serious complications of TAVR. Patient-specific predisposing factors have been well characterized. However, much less is known about device-specific complications. Awareness of the possible device-related complications may lead to earlier identification, prompt management, and better outcomes. We report a previously unreported complication of the Edwards expandable eSheath that lead to avulsion of the external iliac artery following successful TAVR with a 29-mm Edwards Sapien 3 transcatheter heart valve. Bleeding was promptly controlled with an occlusion balloon and emergency surgical repair was required with a favorable outcome.

Routine postaccess-closure angiography to detect vascular complications following transfemoral TAVR.

BACKGROUND: Vascular complications following transfemoral TAVR are associated with increased morbidity and mortality. Measures that may mitigate this risk are important. AIM: To evaluate the utility of routine, access-vessel angiography post sheath-removal in the detection and management of complications in patients undergoing transcatheter aortic valve replacement (TAVR). METHODS: This was a retrospective study of 512 consecutive patients who underwent transfemoral TAVR with routine post access-closure angiography from the radial artery. Rates of mild angiographically evident bleeding, bleeding requiring surgery/interventional-radiology, ischemia, 90-day access-site-related events, and major and minor vascular complications using Valve Academic Research Consortium 3 definitions were recorded. RESULTS: Of 512 patients, digital subtraction angiography (DSA) was undertaken via the radial artery in 467 patients (91%). In the remaining patients (9%) DSA was either not attempted, due to concerns regarding kidney disease and contrast volume, or failed due to anatomical factors (aortic tortuosity/calcification). Significant chronic kidney disease was present at baseline in 72.4% of this cohort (stages III-IV or dialysis). Ninety-four percent of cases underwent TAVR using a balloon-expandable platform. Mild iliofemoral extravasation was observed in 7.7% of the DSA cases. These cases were managed by manual compression with none requiring any vascular intervention subsequently. Valve Academic Research Consortium 3 major and minor access-site-related complications were observed in 0.4% and 12.2%, respectively. Access-site-related bleeding and ischemic events requiring interventional-radiology or vascular-surgery were observed in 0.9% and 1.7% of the DSA cases, respectively. No new renal replacement therapy was needed in any of the DSA cases. Discharge to 90-day access-related complications was 0.8%. CONCLUSIONS: Routine post access-closure angiography is feasible via the radial artery in patients undergoing transfemoral TAVR and appears safe. It facilitates early identification of complications and mitigates risk by enabling prompt action to be taken. Larger studies are needed to confirm these findings.

Long-term durability of self-expanding and balloon-expandable transcatheter aortic valve prostheses: UK TAVI registry.

BACKGROUND: With expansion of transcatheter aortic valve implantation (TAVI) into younger patients, valve durability is critically important. AIMS: We aimed to evaluate long-term valve function and incidence of severe structural valve deterioration (SVD) among patients ≥ 10-years post-TAVI and with echocardiographic follow-up at least 5-years postprocedure. METHODS: Data on patients who underwent TAVI from 2007 to 2011 were obtained from the UK TAVI registry. Patients with paired echocardiograms postprocedure and ≥5-years post-TAVI were included. Severe SVD was determined according to European task force guidelines. RESULTS: 221 patients (79.4 ± 7.3 years; 53% male) were included with median echocardiographic follow-up 7.0 years (range 5-13 years). Follow-up exceeded 10 years in 43 patients (19.5%). Valve types were the supra-annular self-expanding CoreValve (SEV; n = 143, 67%), balloon-expandable SAPIEN/XT (BEV; n = 67, 31%), Portico (n = 4, 5%) and unknown (n = 7, 3%). There was no difference between postprocedure and follow-up peak gradient in the overall cohort (19.3 vs. 18.4 mmHg; p = NS) or in those with ≥10-years follow-up (21.1 vs. 21.1 mmHg; p = NS). Severe SVD occurred in 13 patients (5.9%; median 7.8-years post-TAVI). Three cases (23.1%) were due to regurgitation and 10 (76.9%) to stenosis. Valve-related reintervention/death occurred in 5 patients (2.3%). Severe SVD was more frequent with BEV than SEV (11.9% vs. 3.5%; p = 0.02), driven by a difference in patients treated with small valves (BEV 28.6% vs. SEV 3.0%; p < 0.01). CONCLUSIONS: Hemodynamic function of transcatheter heart valves remains stable up to more than 10 years post-TAVI. Severe SVD occurred in 5.9%, and valve-related death/reintervention in 2.3%. Severe SVD was more common with BEV than SEV.

Development of Stable Boron Nitride Nanotube and Hexagonal Boron Nitride Dispersions for Electrophoretic Deposition.

Boron nitride nanotubes (BNNTs) represent a relatively new class of materials that provides alternative electrical and thermal properties to the carbon analogue. The high chemical and thermal stability and large band gap combined with high electrical resistance make BNNTs desirable in several thin-film applications. In this study, stable BNNT and hexagonal boron nitride (hBN) particle dispersions have been developed using environmentally friendly advanced oxidation processing (AOP) that can be further modified for electrophoretic deposition (EPD) to produce thin films. The characterization of the dispersions has revealed how the hydroxyl radicals produced in AOP react with BNNT/hBN and contaminant boron nanoparticles (BNPs). While the radicals remove the carbon contaminant present on BNNT/hBN and increase dispersion stability, they also oxidize the BNPs and the boron oxide produced, which, conversely, reduces the dispersion stability. The use of high- or low-powered ultrasonication in combination with the AOP affects the rate of the competing reactions, with low-powered sonication and AOP providing the best combination for producing stable dispersions with high concentrations. BNNT/hBN dispersions were functionalized with polyethyleneimine to facilitate EPD, where films of several micrometer thickness were readily deposited onto stainless steel and glass-fiber fabrics. BNNT/hBN films produced on glass fabrics by EPD exhibited a consistent through-thickness macroporosity that was facilitated by platelet and nanotube stacking. The film macroporosity present on the coated fabrics was suitable for use as separator layers in supercapacitors and provided improved device robustness with a minimal impact on electrochemical performance.

Initial experience of a large, self-expanding, and fully recapturable transcatheter aortic valve: The UK & Ireland Implanters' registry.

OBJECTIVES: The UK & Ireland Implanters' registry is a multicenter registry which reports on real-world experience with novel transcatheter heart valves. BACKGROUND: The 34 mm Evolut R transcatheter aortic valve is a self-expanding and fully recapturable transcatheter aortic valve, designed to treat patients with a large aortic annulus. METHODS: Between January 2017 and April 2018, clinical, procedural and 30-day outcome data were prospectively collected from all patients receiving the 34 mm Evolut R valve across 17 participating centers in the United Kingdom and Ireland. The primary efficacy outcome was the Valve Academic Research Consortium-2(VARC-2)-defined endpoint of device success. The primary safety outcome was the VARC-2-defined composite endpoint of early safety at 30 days. RESULTS: A total of 217 patients underwent attempted implant. Mean age was 79.5 ± 8.8 years and Society of Thoracic Surgeons Predicted Risk of Mortality Score 5.2% ± 3.4%. Iliofemoral access was used in 91.2% of patients. Device success was 79.7%. Mean gradient was 7.0 ± 4.6 mmHg and effective orifice area 2.0 ± 0.6 cm2 . Paravalvular regurgitation was more than mild in 7.2%. A new permanent pacemaker was implanted in 15.7%. Early safety was demonstrated in 91.2%. At 30 days, all-cause mortality was 3.2%, stroke 3.7%, and major vascular complication 2.3%. CONCLUSIONS: Real-world experience of the 34 mm Evolut R transcatheter aortic valve demonstrated acceptable procedural success, safety, valve function, and incidence of new permanent pacemaker implantation.

A feasibility study of transaxillary TAVI with the lotus valve.

OBJECTIVES: To assess the feasibility of axillary transcatheter aortic valve implantation (TAVI) using the Lotus valve. BACKGROUND: TAVI is used to treat patients with severe aortic stenosis, with transfemoral (TF) access being the safest and most widely used route. In patients unsuitable for this, there are reports that the axillary artery may be safest alternative access route. The Lotus device is a fully retrievable 2nd generation transcatheter heart valve which is licensed for femoral and transaortic access. There are limited data on the suitability of this valve for axillary access. METHODS: We assessed the feasibility of transaxillary TAVI with the Lotus valve in patients unsuitable for TF TAVI. Between January and October 2016, we identified 10 patients who underwent transaxillary TAVI with the Lotus valve. This cohort was compared with 347 (85%) patients who underwent TF TAVI, 45 (11%) patients who underwent and trans-apical or direct-aortic TAVI and the total group of 16 (4%) patients who underwent axillary TAVI. RESULTS: Ten patients aged 75 years (69-83) underwent attempted TAVI with the Lotus via axillary access. Device success was 100%. In-hospital and 30-day mortality was zero. There were no neurological events, no major vascular complications and no myocardial infarctions. Four of 10 patients required a pacemaker post-TAVI. No patient was left with moderate or greater aortic regurgitation. Median length of stay was 3 days CONCLUSIONS: TAVI with the Lotus valve is feasible via the axillary artery and appears safe in our small cohort of patients.

Feasibility and efficacy of the 2.5 L and 3.8 L impella percutaneous left ventricular support device during high-risk, percutaneous coronary intervention in patients with severe aortic stenosis.

OBJECTIVE: Assessment of the feasibility and outcomes of the 2.5 L and 3.8 L Impella cardiac pump in patients with severe aortic stenosis (AS) and left ventricular impairment undergoing percutaneous revascularization (PCI) with or without balloon aortic valvuloplasty (BAV). METHODS: We reviewed the clinical and procedural findings from a consecutive series of unselected patients with severe AS who underwent PCI during Impella support. In addition, we describe novel "balloon-assist" techniques that allowed implantation of Impella into the left ventricle (LV) when initial unassisted attempts failed. RESULTS: Five patients with severe AS were identified (four males, age 78.2 years, aortic valve area (AVA) 0.6 cm(2) , left ventricular ejection fraction (LVEF) 24 ± 5%, mean Society of Thoracic Surgeons (STS) mortality 11% (range 3-17%)). The Impella catheter traversed the aortic valve (AV) unassisted in only one patient, with four cases requiring balloon-assist techniques. All patients underwent planned revascularisation; mean procedure time 177 min (range 135-252 min), mean number of stents 3.4 (range 1-8), with three patients requiring rotational atherectomy. All procedures were well tolerated, with absence of arrhythmia, hypotension, pulmonary edema, stroke, or myocardial infarction. One patient died 48 hr post-PCI of multi-organ failure. The four remaining patients were well at 30 days. CONCLUSION: Implantation of the 2.5 and 3.8 L Impella appears feasible in patients with severe AS and left ventricle (LV) impairment. A balloon-assist technique may be used to facilitate device implantation when initial unassisted attempts fail. Improved hemodynamic stability may enhance the tolerability of lengthy and complex procedures.

Use of left ventricular support devices during acute coronary syndrome and percutaneous coronary intervention.

In an effort to improve outcomes in percutaneous coronary intervention (PCI), percutaneous ventricular assist devices (PVADs) have been investigated in (1) high-risk PCI, (2) acute myocardial infarction (AMI) complicated by cardiogenic shock (CS) and (3) in AMI without CS. PCI has become an increasing complex due to an ageing population with complex disease and the frequent presence of impaired LV function. Patients undergoing high-risk PCI in these circumstances are prone to acute cardiovascular collapse. Additionally, mortality in AMI complicated by CS remains high. Lastly, LV support during AMI may reduce infarct size and therefore preserve LV function. At present, four commercially available devices exist: intra-aortic balloon pump counterpulsation (IABP), Impella, TandemHeart and extracorporeal membrane oxygenation (ECMO). These devices are employed in an effort to increase cardiac output, mean arterial pressure (MAP) and coronary perfusion and to reduce pulmonary capillary wedge pressure (PCWP). The mechanism of action differs with each device, and there are advantages and disadvantages. In this update, we discuss recent data describing the use of PVADs to support patients with AMI with or without cardiogenic shock and during high-risk PCI. We focus on the unique features of each device, highlighting strengths, weaknesses and frequently encountered complications, which may be important when tailoring the most appropriate PVAD therapy to an individual patient's need.

Automated cardiopulmonary resuscitation: a case study.

Rates of survival after cardiac arrest are low and correlate with the quality of cardiopulmonary resuscitation (CPR). Devices that deliver automated CPR (A-CPR) can provide sustained and effective chest compressions, which are especially useful during patient transfer and while simultaneous invasive procedures are being performed. The use of such devices can also release members of resuscitation teams for other work. This article presents a case study involving a man with acute myocardial infarction complicated by cardiogenic shock and pulmonary oedema. It describes how ED nursing and medical teams worked together to deliver A-CPR, discusses the use of A-CPR devices in a tertiary cardiac centre, and highlights the advantages of using such devices.

Prevalence and Impact of Concomitant Atrial Fibrillation in Patients Undergoing Percutaneous Coronary Intervention for Acute Myocardial Infarction.

Background: Concomitant atrial fibrillation (AF) is associated with an adverse prognosis in patients with acute myocardial infarction (MI). However, it remains unclear whether this is due to a causal effect of AF or whether AF acts as a surrogate marker for comorbidities in this population. Furthermore, there are limited data on whether coronary artery disease distribution impacts the risk of developing AF. Methods: Consecutive patients admitted with acute MI and treated using percutaneous coronary intervention (PCI) at a single centre were retrospectively identified. Associations between AF and major adverse cardiac and cerebrovascular events (MACCEs) over a median of five years of follow-up were assessed using Cox regression, with adjustment for confounding factors performed using both multivariable modelling and a propensity-score-matched analysis. Results: AF was identified in N = 65/1000 (6.5%) of cases; these patients were significantly older (mean: 73 vs. 65 years, p < 0.001), with lower creatinine clearance (p < 0.001), and were more likely to have a history of cerebrovascular disease (p = 0.011) than those without AF. In addition, patients with AF had a greater propensity for left main stem (p = 0.001) or left circumflex artery (p = 0.004) involvement. Long-term MACCE rates were significantly higher in the AF group than in the non-AF group (50.8% vs. 34.2% at five years), yielding an unadjusted hazard ratio (HR) of 1.86 (95% CI: 1.32-2.64, p < 0.001). However, after adjustment for confounding factors, AF was no longer independently associated with MACCEs, either on multivariable (adjusted HR: 1.25, 95% CI: 0.81-1.92, p = 0.319) or propensity-score-matched (HR: 1.04, 95% CI: 0.59-1.82, p = 0.886) analyses. Conclusions: AF is observed in 6.5% of patients admitted with acute MI, and those with AF are more likely to have significant diseases involving left main or circumflex arteries. Although unadjusted MACCE rates were significantly higher in patients with AF, this effect was not found to remain significant after adjustment for comorbidities. As such, this study provided no evidence to suggest that AF is independently associated with MACCEs.

Adhesion Characterization and Enhancement between Polyimide-Silica Composite and Nodulated Copper for Applications in Next-Generation Microelectronics.

As the need for high-speed electronics continues to rise rapidly, printed wiring board (PWB) requirements become ever-more demanding. A typical PWB is fabricated by bonding dielectric films such as polyimide to electrically conductive copper foil such as rolled annealed (RA) copper and is expected to become thinner, flexible, durable, and compatible with high-frequency 5G performance. Polyimide films inherently feature a higher coefficient of thermal expansion (CTE) than copper foils; this mismatch causes residual thermal stresses. To attenuate the mismatch, silica nanoparticles may be used to reduce the CTE of PI. A nodulated copper surface can be used to enhance the Cu/PI adhesion by additional bonding mechanisms that could include a type of mechanical bonding, which is a focus of this study. In this investigation, a 90° peel test was used to measure the peel strength in copper/polyimide/copper laminates containing nodulated copper and polyimide reinforced with 0, 20, and 40 wt % silica nanoparticles. The influence of silica nanoparticles on the peel strength was quantitatively evaluated. Laminates incorporating polyimide films lacking silica nanoparticles had a ∼3.75× higher peel strength compared with laminates reinforced with 40% silica. Their failure surfaces were analyzed by using scanning electron microscopy (SEM), energy-dispersive X-ray analysis (EDX), and X-ray photoelectron spectroscopy to identify the mode of failure and to understand bonding mechanisms. The key bonding mechanism, mechanical interlocking, was achieved when the polyimide surrounded or engulfed the copper nodules when the laminate was created. Post-testing failure surface analysis revealed the presence of copper on the polyimide side and polyimide on the copper side, indicating mixed mode failure. An analytical model was developed to determine the impact of applied pressure, temperature, and time on the polyimide penetration and mechanical interlocking around the copper nodules. The model was validated by measuring the peel strength on another set of specimens fabricated using increased temperature and pressure that showed a 3× increase in peel strength compared to lower temperature/pressure processing conditions. This enhanced adhesion resulted from the lower polymer material viscosity at higher temperatures, which fosters deeper and more complete penetration around the copper nodules during processing at higher pressures for longer durations. The methodology of combining peel testing, viscosity and CTE measurement, SEM/EDX, surface chemical analysis, and penetration depth calculation developed herein enables the calculation of the desired processing parameters to enhance functionality and improve adhesion.

Bleeding outcomes after routine transradial primary angioplasty for acute myocardial infarction using eptifibatide and unfractionated heparin: a single-center experience following the HORIZONS-AMI trial.

OBJECTIVES: We sought to (1) determine the bleeding rates after primary percutaneous coronary intervention (PPCI) in our institution, where the default strategy has been transradial (TR) access in combination with unfractionated heparin (UFH) plus eptifibatide, and (2) compare these with the outcomes of patients treated with bivalirudin in HORIZONS-AMI. BACKGROUND: HORIZONS-AMI demonstrated that in PPCI undertaken via the transfemoral route, routine use of bivalirudin was associated with lower bleeding rates and improved mortality compared to routine use of UFH plus glycoprotein IIb/IIIa inhibitor (GPI). METHODS: This was a single-center prospective registry of consecutive patients undergoing PPCI from January 2009 to August 2011 at the Queen Elizabeth Hospital Birmingham, UK. Thirty-day major bleeding was defined as per the HORIZONS-AMI criteria and also according to TIMI and GUSTO scales. RESULTS: Of the 432 consecutive patients, 350 fulfilled entry criteria for HORIZONS-AMI. In contrast with HORIZONS-AMI, these subjects were older (62.5 ± 13.7 yr vs. 59.8 ± 11.1 yr, P < 0.05) with a higher rate of cardiogenic shock (6.3% vs. 0.8%, P < 0.0001). Despite this higher risk population, the rate of major bleeding was favorable (3.7% [95% CI: 2.0-6.3%] vs. 4.9% [4.0-6.1%], P = 0.32). Similarly, TIMI major bleeding (2.0% [0.8-4.1%] vs. 3.1% [2.3-3.4%], P = 0.10) and GUSTO severe or life-threatening bleeding (0.6% [0.1-2.5%] vs. 0.4% [0.2-0.9%], P = 0.75) were comparable. CONCLUSIONS: Routine TR access for PPCI using UFH plus GPI is associated with a low 30-day rate of major bleeding equivalent to the bivalirudin arm of HORIZONS-AMI. Default transradial access for PPCI permits routine use of a GPI without the penalty of high bleeding rates.

Standalone balloon aortic valvuloplasty: indications and outcomes from the UK in the transcatheter valve era.

OBJECTIVES: We sought to characterize UK-wide balloon aortic valvuloplasty (BAV) experience in the TAVI era. BACKGROUND: BAV for acquired calcific aortic stenosis is in a phase of renaissance, largely due to the development of transcatheter aortic valve implantation (TAVI). METHODS: Data from 423 patients at 14 centers across the UK were analyzed. RESULTS: Patients were aged 80.9 ± 9.5 years; 52.5% were male. Mean logistic EuroScore was 27.3% ± 16.8%. Mean peak transaortic gradient fell from 62.0 ± 26.3 to 28.3 ± 16.2 mm Hg. Aortic valve area increased from 0.58 ± 0.19 to 0.80 ± 0.25 cm(2) echocardiographically. Procedural complication rate was 6.3%, comprising death (2.4%), blood transfusion ≥ 2 U (1.2%), cardiac tamponade (1.0%), stroke (1.0%), vascular surgical repair (1.0%), coronary embolism (0.5%), and permanent pacemaker (0.2%). Mortality was 13.8% at 30 days and 36.3% at 12 months. Subsequently, 18.3% of patients underwent TAVI and 7.0% sAVR, with improved survival compared to those who had no further intervention (logrank < 0.0001). Multivariate Cox proportional hazard analysis demonstrated that survival was adversely effected by the presence of coronary artery disease (HR 1.53, 95%CI 1.08-2.17, P = 0.018), poor LV function (HR 1.54, 95%CI 1.09-2.16, P = 0.014), and either urgent (HR 1.70, 95%CI 1.18-2.45; P = 0.004) or emergent presentation (HR 3.72, 95%CI 2.27-6.08; P < 0.0001). CONCLUSION: Balloon aortic valvuloplasty offers good immediate hemodynamic efficacy at an acceptable risk of major complications. Medium-term prognosis is poor in the absence of definitive therapy.

VersaCross Transseptal System for Mitral Transcatheter Edge-To-Edge Repair With the PASCAL Repair Platform.

Background: VersaCross is a novel radiofrequency transseptal solution that may improve the efficiency and workflow of transseptal puncture (TSP). The aim of this study was to compare the VersaCross transseptal system with mechanical needle systems during mitral transcatheter edge-to-edge repair (M-TEER) with the PASCAL device. Methods: This is a single-center retrospective study of consecutive patients who underwent M-TEER with the PASCAL. Transseptal puncture was undertaken with either a mechanical needle or the VersaCross wire. The primary endpoints were success of TSP and successful delivery of the Edwards sheath on the chosen delivery wire. Secondary endpoints included number of wires used, tamponade rate, interval from femoral venous access to TSP and first PASCAL device deployment, procedural death, and stroke. Results: Thirty-three consecutive patients (10 with mechanical needle, 23 with VersaCross) who underwent M-TEER with the Edwards PASCAL device were identified. All patients had successful TSP. In the mechanical needle group, the Edwards sheath was successfully delivered on the Superstiff Amplatz wire in all cases. In the VersaCross arm, the radiofrequency wire was used successfully for delivery of the sheath in all cases. There were no cases of pericardial effusion/tamponade in either arm. Interval from femoral venous access to TSP and to deployment of the first PASCAL device was shorter with the VersaCross system. Significantly fewer wires were used with VersaCross. There were no procedural deaths or strokes in either group. Conclusions: VersaCross appears a safe and effective method of TSP and for delivery of the 22Fr sheath for M-TEER with PASCAL.

Estimating ground reaction force with novel carbon nanotube-based textile insole pressure sensors.

This study presents a new wearable insole pressure sensor (IPS), composed of fabric coated in a carbon nanotube-based composite thin film, and validates its use for quantifying ground reaction forces (GRFs) during human walking. Healthy young adults (n = 7) walked on a treadmill at three different speeds while data were recorded simultaneously from the IPS and a force plate (FP). The IPS was compared against the FP by evaluating differences between the two instruments under two different assessments: (1) comparing the two peak forces at weight acceptance and push-off (2PK) and (2) comparing the absolute maximum (MAX) of each gait cycle. Agreement between the two systems was evaluated using the Bland-Altman method. For the 2PK assessment, the group mean of differences (MoD) was -1.3 ± 4.3% body weight (BW) and the distance between the MoD and the limits of agreement (2S) was 25.4 ± 11.1% BW. For the MAX assessment, the average MoD across subjects was 1.9 ± 3.0% BW, and 2S was 15.8 ± 9.3% BW. The results of this study show that this sensor technology can be used to obtain accurate measurements of peak walking forces with a basic calibration and consequently open new opportunities to monitor GRF outside of the laboratory.

Antithrombotic therapy following transcatheter aortic valve intervention.

Transcatheter aortic valve replacement (TAVR) is increasingly being performed to treat symptomatic patients with aortic stenosis and annual procedure volume has overtaken surgical aortic valve replacement in the United States. However, current international guidelines were written prior to the publication of several important recent studies. Furthermore, European and American guidelines differ in their recommendations of antithrombotic therapy following TAVR. Consequently, there is a need to examine the literature to provide clinicians guidance on the optimum antithrombotic strategy, particularly as different patient populations exist. In this review, we examine the data for antiplatelet and anticoagulation therapy post-TAVR.

Intraprocedural versus next day transthoracic echocardiography following minimalist transfemoral TAVI.

BACKGROUND: Routine pre-discharge echocardiography (ECHO) is recommended post transcatheter aortic valve implantation (TAVI) as a baseline for future comparison. However, there is no clear guidance on the optimal timing of this study. AIM: The purpose of this retrospective study was to investigate the safety and work-force efficiency of intraprocedural same-day ECHO versus next-day ECHO, following transfemoral TAVI. METHODS AND RESULTS: In this retrospective study 100 consecutive patients who underwent intraprocedural ECHO only were compared with 100 consecutive patients undergoing both intraprocedural and routine next-day ECHO following elective transfemoral TAVI. All patients received the Sapien 3/Ultra transcatheter heart valve and were treated with a minimalist procedure with conscious sedation. The composite of in-hospital mortality, urgent ECHO and new tamponade after leaving the cath lab and before discharge was not different between the two groups (4 vs. 4%, P = 1). There was no paravalvular leak more than mild in any of the cases. Length of stay was similar (1 day). CONCLUSIONS: Intraprocedural post-TAVI ECHO appears as safe as next day pre-discharge ECHO and obviates the need for a routine next day study, thereby reducing burden on echocardiography services and allows better utilisation of resources.

Carbon Additive Manufacturing with a Near-Replica "Green-to-Brown" Transformation.

Nanocomposites containing nanoscale materials offer exciting opportunities to encode nanoscale features into macroscale dimensions, which produces unprecedented impact in material design and application. However, conventional methods cannot process nanocomposites with a high particle loading, as well as nanocomposites with the ability to be tailored at multiple scales. A composite architected mesoscale process strategy that brings particle loading nanoscale materials combined with multiscale features including nanoscale manipulation, mesoscale architecture, and macroscale formation to create spatially programmed nanocomposites with high particle loading and multiscale tailorability is reported. The process features a low-shrinking (<10%) "green-to-brown" transformation, making a near-geometric replica of the 3D design to produce a "brown" part with full nanomaterials to allow further matrix infill. This demonstration includes additively manufactured carbon nanocomposites containing carbon nanotubes (CNTs) and thermoset epoxy, leading to multiscale CNTs tailorability, performance improvement, and 3D complex geometry feasibility. The process can produce nanomaterial-assembled architectures with 3D geometry and multiscale features and can incorporate a wide range of matrix materials, such as polymers, metals, and ceramics, to fabricate nanocomposites for new device structures and applications.

Kissing drug eluting balloons for in-stent restenosis complicating bifurcations treated with drug-eluting stents.

The management of in-stent restenosis (ISR) complicating bifurcation lesions is technically challenging and implant of further stents may not be feasible. The use of drug-eluting balloons provides an attractive option for treatment of such lesions allowing a technically simple procedure without the need for further complex stenting. The SeQuent Please paclitaxel-eluting balloon (B. Braun, Berlin, Germany) has been shown to be superior to a paclitaxel eluting stent or balloon angioplasty for ISR complicating a bare-metal stent. However, there is no data on the efficacy of the SeQuent Please in ISR complicating drug-eluting stents or bifurcation lesions. We report two cases where the SeQuent Please was used in this setting with angiographic success and freedom from target vessel failure and angina at 24 months. In both cases the Sheathless Eau Cath guide (Asahi Intecc, Japan) was employed to perform a kissing-balloon dilatation with the SeQuent Please, so allowing treatment via radial access.