Nitrite anodic oxidation at Ni(II)/Ni(III)-decorated mesoporous SnO2 and its analytical applications.

Hydrothermally formed mesoporous SnO2 was used as a support for nickel chemical deposition and, after subsequent thermal treatment, a high specific surface area (36 m2 g-1) Ni/SnO2 material was obtained. XPS analysis has shown that in the Sn 3d region the spectrum is similar to that of pristine SnO2, whereas Ni species are present on the surface as NiO, Ni2O3 and Ni(OH)2. Mixing Ni/SnO2 with a small amount of Black Pearls (BP) leads to a significant enhancement of the resulting Ni/SnO2-BP composite activity for nitrite anodic oxidation, presumably due to the higher surface area (115 m2 g-1), to better electrical conductivity and to a certain contribution of the BP to an increase in surface density of the active sites. Ni/SnO2-BP also outperforms pristine BP (in terms of Tafel slopes and electron-transfer rates), most likely due to the fact that the Ni(II)/Ni(III) couple can act as an electrocatalyst for nitrite oxidation. A voltammetric method is proposed for the determination of nitrite, over a concentration range of three orders of magnitude (0.05 to 20 mM), with good reproducibility, high stability and excellent sensitivity. The high upper limit of the dynamic range of the analytically useful response might provide a basis for the reliable quantification of nitrite in wastewater.

Optoelectronic and stability properties of quasi-2D alkylammonium based perovskites.

Electronic and stability properties of quasi-2D alkylammonium perovskites are investigated using density functional theory (DFT) calculations and validated experimentally on selected classes of compounds. Our analysis is focused on perovskite structures of formula (A)2(A')n-1PbnX3n+1, with large cations A = butyl-, pentyl-, hexylammonium (BA, PA, HXA), small cations A' = methylammonium, formamidinium, ethylammonium, guanidinium (MA, FA, EA, GA) and halogens X = I, Br, Cl. The role of the halogen ions is outlined for the band structure, stability and defect formation energies. Two opposing trends are found for the absorption efficiency versus stability, the latter being assessed with respect to possible degradation mechanisms. Experimental validation is performed on quasi-2D perovskites based on pentylammonium cations, namely: (PA)2PbX4 and (PA)2(MA)Pb2X7, synthesized by antisolvent-assisted vapor crystallization. Structural and optical analysis are inline with the DFT based calculations. In addition, the thermogravimetric analysis shows an enhanced stability of bromide and chloride based compounds, in agreement with the theoretical predictions.

Carbon-Coated SiO2 Composites as Promising Anode Material for Li-Ion Batteries.

Porous silica-based materials are a promising alternative to graphite anodes for Li-ion batteries due to their high theoretical capacity, low discharge potential similar to pure silicon, superior cycling stability compared to silicon, abundance, and environmental friendliness. However, several challenges prevent the practical application of silica anodes, such as low coulombic efficiency and irreversible capacity losses during cycling. The main strategy to tackle the challenges of silica as an anode material has been developed to prepare carbon-coated SiO2 composites by carbonization in argon atmosphere. A facile and eco-friendly method of preparing carbon-coated SiO2 composites using sucrose is reported herein. The carbon-coated SiO2 composites were characterized using X-ray diffraction, X-ray photoelectron spectroscopy, thermogravimetry, transmission and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy, cyclic voltammetry, and charge-discharge cycling. A C/SiO2-0.085 M calendered electrode displays the best cycling stability, capacity of 714.3 mAh·g-1, and coulombic efficiency as well as the lowest charge transfer resistance over 200 cycles without electrode degradation. The electrochemical performance improvement could be attributed to the positive effect of the carbon thin layer that can effectively diminish interfacial impedance.

Defect induced tunable near infrared emission of Er-CeO2 by heterovalent co-dopants.

We investigate the effects of heterovalent co-dopants on the structural and emission properties of 1% Er-CeO2 nanoparticles. The CeO2 oxide host was selected on the basis of its fairly well-understood defect chemistry in either a pure or doped state. As a luminescent activator, Er is acknowledged as an interesting element due to its rich luminescence and excitation properties spanning the visible to near-infrared range. The optically inactive trivalent La and monovalent Li metal ions with a concentration of up to 20% were chosen to presumably generate a variable amount of defects in the Er-CeO2 lattice. It was found that La and Li co-dopants induced distinct changes related to the size, lattice constant, bandgap energy, lattice and surface defects of Er-CeO2. As a result of these changes, a strong modulation of the luminescence intensity and shape was measured using a suite of excitation conditions (charge-transfer absorption band of CeO2, direct/up-conversion into Er absorptions and X-ray excitation modes). The use of Eu as a luminescent probe offered additional information concerning the effects of La/Li co-doping on the local structure surrounding the luminescent activator. Remarkably high percentages of 90 and 98% of the total emission of Er measured between 500 and 1100 nm are measured in the near-infrared region at 980 nm under X-ray and up-conversion excitation at ∼1500 nm, respectively. The optical properties suggest that Li, Er co-doped CeO2 has good potential for therapy and biological imaging.

Pure and almost pure NIR emission of Tm and Tm,Yb-CeO2 under UV, X-ray and NIR up-conversion excitation: key roles of level selective antenna sensitization and charge-compensation.

Herein, we report on the pure and almost pure near-infrared (NIR) emission at around 807 nm observed for Tm(Yb) (co)-doped CeO2 nanoparticles (NPs) under UV, X-ray and NIR up-conversion excitation. The optical responses are attributed to the low-lying charge-transfer of CeO2 that acts as a selective antenna sensitizer of the Tm (3)H4 emission and Yb doping that lowers the local symmetry at Tm sites and introduces additional phonon modes. Selective antenna sensitization is also observed for Er/Ho (Yb) (co)-doped CeO2 NPs. To the best of our knowledge, this is a first study which correlates the down- and up-conversion emission properties of lanthanide(s)-(co) dopants with the CeO2 structure highlighting also the outstanding potential of these NPs in high-penetration tissue imaging and therapy.

Green synthesis of aminated hyaluronic acid-based silver nanoparticles on modified titanium dioxide surface: Influence of size and chemical composition on their biological properties.

This is the first report on an efficient, "environmentally friendly" chemical reduction method for the synthesis of aminated hyaluronic acid-based silver nanoparticles on the modified surface of titanium dioxide nanoparticles aimed for biological applications. Silver nanoparticles exhibit well-known physical-chemical and optical properties appropriate for different biological applications. Modifying the nanoparticles leads to a change in their expected bioactivity. This represents an important topic for the current research. We have developed a novel aminated hyaluronic acid (HA-EDA)-based protocol to obtain silver nanoparticles, in which HA-EDA was used for the first time as a reducing and stabilizing agent. The effect of the size of silver nanoparticles on the titanium dioxide surface and the chemical composition of the obtained materials were investigated by TEM, XRD, XPS, ATR-FTIR, Raman spectroscopy, NMR and H2-TPR analyses. The antioxidant, in vitro biocompatibility, and antimicrobial activity of the fabricated composites have been evaluated. The results prove that the prepared materials exhibit antimicrobial, antioxidant, and anti-inflammatory activity, thus providing protection against infection and supporting tissue regeneration, these two key effects being of paramount importance for promoting wound healing.

Influence of Ferroelectric Filler Size and Clustering on the Electrical Properties of (Ag-BaTiO3)-PVDF Sub-Percolative Hybrid Composites.

The paper presents a study concerning the role of ferroelectric filler size and clustering in the dielectric properties of 20%BaTiO3-80%PVDF and of 20% (2%Ag-98%BaTiO3)-PVDF hybrid nanocomposites. By finite element calculations, it was shown that using fillers with ε > 103 does not provide a permittivity rise in the composites and the effective dielectric constant tends to saturate to specific values determined by the filler size and agglomeration degree. Irrespective of the ferroelectric filler sizes, the addition of metallic ultrafine nanoparticles (Ag) results in permittivity intensification and the effect is even stronger if the metallic nanoparticles are connected to a higher degree with the ferroelectric particles' surfaces. When using coarse ferroelectric fillers, the probability of clustering is higher, thus favoring the permittivity increase by field concentration in small regions close to the interfaces separating dissimilar materials. The modeling results were validated by an experimental dielectric analysis performed in a series of PVDF-based thick films with the same amount of BaTiO3 fillers or with Ag-BaTiO3 hybrid fillers. Similar trends as predicted by simulations were found experimentally but with slightly higher permittivity values which were assigned to the modifications of the polymer phase composition due to the presence of nanofillers and the local sample inhomogeneity (the presence of clustering, in particular for coarse BaTiO3 grains), which create regions with enhanced local fields.

A robust metal-organic framework constructed from alkoxo-bridged binuclear nodes and hexamethylenetetramine spacers: crystal structure and sorption studies.

A neutral 3D metal-organic framework, (3)(∞)[Cu(2)(mand)(2)(hmt)]·H(2)O (1), was constructed from binuclear Cu(2)O(2) alkoxo-bridged nodes, generated by the doubly deprotonated mandelic acid. The nodes are connected by hexamethylenetetramine (hmt) spacers, which act as biconnective bridging ligands, and by carboxylato groups. Channels are observed along the crystallographic c axis. The water molecules from the channels can be easily removed, preserving the architecture of the crystal, which is stable up to 280 °C. The Langmuir surface area was found to be 610 m(2) g(-1). The sorption ability of 1 was investigated using H(2) and CO(2).

Electrocatalytic Properties of Mixed-Oxide-Containing Composite-Supported Platinum for Polymer Electrolyte Membrane (PEM) Fuel Cells.

TiO2-based mixed oxide-carbon composite supports have been suggested to provide enhanced stability for platinum (Pt) electrocatalysts in polymer electrolyte membrane (PEM) fuel cells. The addition of molybdenum (Mo) to the mixed oxide is known to increase the CO tolerance of the electrocatalyst. In this work Pt catalysts, supported on Ti1-xMoxO2-C composites with a 25/75 oxide/carbon mass ratio and prepared from different carbon materials (C: Vulcan XC-72, unmodified and functionalized Black Pearls 2000), were compared in the hydrogen oxidation reaction (HOR) and in the oxygen reduction reaction (ORR) with a commercial Pt/C reference catalyst in order to assess the influence of the support on the electrocatalytic behavior. Our aim was to perform electrochemical studies in preparation for fuel cell tests. The ORR kinetic parameters from the Koutecky-Levich plot suggested a four-electron transfer per oxygen molecule, resulting in H2O. The similarity between the Tafel slopes suggested the same reaction mechanism for electrocatalysts supported by these composites. The HOR activity of the composite-supported electrocatalysts was independent of the type of carbonaceous material. A noticeable difference in the stability of the catalysts appeared only after 5000 polarization cycles; the Black Pearl-containing sample showed the highest stability.

Increasing Permittivity and Mechanical Harvesting Response of PVDF-Based Flexible Composites by Using Ag Nanoparticles onto BaTiO3 Nanofillers.

The role of Ag addition on the structural, dielectric, and mechanical harvesting response of 20%(xAg - (1 - x)BaTiO3) - 80%PVDF (x = 0, 2, 5, 7 and 27 vol.%) flexible composites is investigated. The inorganic fillers were realized by precipitating fine (~3 nm) silver nanoparticles onto BaTiO3 nanoparticles (~60 nm average size). The hybrid admixtures with a total filling factor of 20 vol.% were embedded into the PVDF matrix. The presence of filler enhances the amount of ß-PVDF polar phase and the BaTiO3 filler induces an increase of the permittivity from 11 to 18 (1 kHz) in the flexible composites. The addition of increasing amounts of Ag is further beneficial for permittivity increase; with the maximum amount (x = 27 vol.%), permittivity is three times larger than in pure PVDF (εr ~ 33 at 1 kHz) with a similar level of tangent losses. This result is due to the local field enhancement in the regions close to the filler-PVDF interfaces which are additionally intensified by the presence of silver nanoparticles. The metallic addition is also beneficial for the mechanical harvesting ability of such composites: the amplitude of the maximum piezoelectric-triboelectric combined output collected in open circuit conditions increases from 0.2 V/cm2 (PVDF) to 30 V/cm2 for x = 27 vol.% Ag in a capacitive configuration. The role of ferroelectric and metallic nanoparticles on the increasing mechanical-electric conversion response is also been explained.

Structural Details of BaTiO3 Nano-Powders Deduced from the Anisotropic XRD Peak Broadening.

In this study, nano-BaTiO3 (BTO) powders were obtained via the solvothermal method at different reaction times and were investigated using transmission electron microscopy (TEM), X-ray diffraction (XRD) and Raman spectroscopy. The results were compared with those obtained for a larger crystallite size BTO powder (BTO-m). The sizes of the cuboid crystallites (as determined by XRD and TEM) ranged from about 18 to 24 nm, depending on the reaction time. The evolution with temperature of the structure parameters of nano-BTO was monitored by means of X-ray diffraction and Raman spectroscopy and no signs of phase transition were found up to 170 °C. Careful monitoring of the dependence of the XRD peak widths on the hkl indices showed that the effect of the cubic crystallite shape upon the XRD peak widths was buried by the effect of hidden tetragonal line splits and by anisotropic microstrain. The good correlation of the line widths with the tetragonal split amplitudes, observed especially for BTO-m above the transition temperature, indicates tetragonal deformations, as also revealed by Raman spectroscopy. The large anisotropic microstrain shown by the nano-powders, which had a maximum value in the <100> directions, was considered evidence of the phenomenon of surface relaxation of cubic crystallites edged by {100} faces. The observed behavior of the nano-BTO structures with increasing temperature may suggest a correlation between the surface relaxation and tetragonal deformation in the nano-cubes. The experimental results for both nano-BTO and mezoscale-BTO are in agreement with the core-shell model.

CuWO4 with CuO and Cu(OH)2 Native Surface Layers for H2S Detection under in-Field Conditions.

The paper presents the possibility of detecting low H2S concentrations using CuWO4. The applicative challenge was to obtain sensitivity, selectivity, short response time, and full recovery at a low operating temperature under in-field atmosphere, which means variable relative humidity (%RH). Three different chemical synthesis routes were used for obtaining the samples labeled as: CuW1, CuW2, and CuW3. The materials have been fully characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). While CuWO4 is the common main phase with triclinic symmetry, different native layers of CuO and Cu(OH)2 have been identified on top of the surfaces. The differences induced into their structural, morphological, and surface chemistry revealed different degrees of surface hydroxylation. Knowing the poisonous effect of H2S, the sensing properties evaluation allowed the CuW2 selection based on its specific surface recovery upon gas exposure. Simultaneous electrical resistance and work function measurements confirmed the weak influence of moisture over the sensing properties of CuW2, due to the pronounced Cu(OH)2 native surface layer, as shown by XPS investigations. Moreover, the experimental results obtained at 150 °C highlight the linear sensor signal for CuW2 in the range of 1 to 10 ppm H2S concentrations and a pronounced selectivity towards CO, CH4, NH3, SO2, and NO2. Therefore, the applicative potential deserves to be noted. The study has been completed by a theoretical approach aiming to link the experimental findings with the CuW2 intrinsic properties.

CeO2:Mn3O4 Catalytic Micro-Converters Tuned for CH4 Detection Based on Catalytic Combustion under Real Operating Conditions.

Mesoporous CeO2:Mn3O4 materials (3:7 and 7:3 molar ratio) were prepared by co-precipitation and deposited as porous thick films over alumina (Al2O3) planar substrate provided with Pt meander. The aim was oriented towards detecting low levels methane (CH4) at moderate operating temperatures. Herein we demonstrated that the sensitivity of catalytic micro-converters (CMCs) towards a given peak of CH4 concentration corresponds to specific gas-surface interaction phenomena. More precisely, a transition from thermal conductivity to combustion rate is likely to occur when CMCs are operated under real atmospheric conditions (normal pressure, presence of relative humidity, and constant operating temperature). The response to CH4 was analyzed over different gas flows and different gas concentrations under the same operating regime. The materials were fully characterized by adsorption-desorption isotherms, H2-Temperature Programmed Reduction (H2-TPR), X-ray Diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Scanning Electron Microscopy (SEM), and Raman spectroscopies. Thus, the applicative aspect of using CeO2:Mn3O4 as moderate temperature CMC for CH4 detection is brought to the fore.

Decompensation of a Thoracic Meningioma Below the Operated Level: A Dramatic and Unexpected Complication.

BACKGROUND: Paraplegia after lumbar spinal surgery has been previously described. It was generally provoked by a missed thoracic compression because of degenerative processes, arachnoid cyst, and spinal cord tumor such as meningioma. We describe here a case of a patient with neurofibromatosis type 2 (NF-2) with multiple spinal meningiomas that developed postoperative paraplegia because of decompensation of spinal cord compression below and far from the operated level. CASE DESCRIPTION: A 54-year-old woman with NF-2 was followed-up for multiple spinal meningiomas (C7-T1, T6-7, T9-10 levels). Surgery for the symptomatic and larger lesion (C7-T1) was scheduled. Postoperatively, the patient was found to have paraplegia with sensor anesthesia below the level of the T6 vertebra. An urgent spinal magnetic resonance imaging (MRI) scan was performed revealing the absence of complication at the operated level (C7-T1) but the appearance of a marked intramedullary hyperintensity at the T6-7 level. An urgent T6-7 laminectomy and removal of the meningioma was performed. The postoperative phase was marked by a poor recuperation. Spinal MRI scan at 3 months clearly showed a severely injured spinal cord at the T6-7 level consistent with the neurologic status of the patient. CONCLUSIONS: We report here the first case of acute neurologic deterioration after decompensation of a spinal cord compression below the operated level in spinal intradural surgery. Neurosurgeons must be aware of this possible complication when treating patients with multiple spinal meningiomas.

Methane Combustion Using Pd Deposited on CeOx-MnOx/La-Al2O3 Pellistors.

Pd deposited on CeOx-MnOx/La-Al2O3 has been prepared as a sensitive material for methane (CH4) detection. The effect of different amounts (1.25%, 2.5% and 5%) of Pd loading has been investigated. The as prepared materials were deposited on Pt microcoils using a drop-coating method, as a way of developing pellistors operated using a Wheatstone bridge configuration. By spanning the operating temperature range between 300 °C and 550 °C, we established the linearity region as well as the maximum sensitivity towards 4900 ppm of CH4. By making use of the sigmoid dependence of the output voltage signal from the Wheatstone bridge, the gas surface reaction and diffusion phenomena have been decoupled. The pellistor with 5% Pd deposited on CeOx-MnOx/La-Al2O3 exhibited the highest selective-sensitivity in the benefit of CH4 detection against threshold limits of carbon monoxide (CO), sulfur dioxide (SO2) and hydrogen sulfide (H2S). Accordingly, adjusting the percent of Pd makes the preparation strategies of pellistors good candidates towards CH4 detection.

Undoped SnO2 as a Support for Ni Species to Boost Oxygen Generation through Alkaline Water Electrolysis.

In this study, the synergistic behavior of Ni species and bimodal mesoporous undoped SnO2 is investigated in oxygen evolution reactions (OERs) under alkaline conditions without any other modification of the compositional phases or using noble metals. An efficient and environmentally friendly hydrothermal method to prepare bimodal mesoporous undoped SnO2 with a very high surface area (>130 m2 g-1) and a general deposition-precipitation method for the synthesis of well-dispersed Ni species on undoped SnO2 are reported. The powders were characterized by adsorption-desorption isotherms, TG-DTA, XRD, SEM, TEM, Raman, TPR-H2, and XPS. The best NiSn composite generates, under certain experimental conditions, a very high TOF value of 1.14 s-1 and a mass activity higher than 370 A g-1, which are remarkable results considering the low amount of Ni deposited on the electrode (3.78 ng). Moreover, in 1 M NaOH electrolyte, this material produces more than 24 mA cm-2 at an overpotential value of approximately +0.33 V, with only 5 wt % Ni species. This performance stems from the dual role of undoped SnO2, on the one hand, as a support for active and well-dispersed Ni species and on the other hand as an active player through the oxygen vacancies generated upon Ni deposition.

Imaging dopant distribution across complete phase transformation by TEM and upconversion emission.

Correlating dopant distribution to its optical response represents a complex challenge for nanomaterials science. Differentiating the "true" clustering nature from dopant pairs formed in statistical distribution complicates even more the elucidation of doping-functionality relationship. The present study associates lanthanide dopant distribution, including all significant events (enrichment, depletion and surface segregation), to its optical response in upconversion (UPC) at the ensemble and single-nanoparticle level. A small deviation from the Er nominal concentration of a few percent is able to induce clear differences in Er UPC emission color, intensity, excited-state dynamics and ultimately, UPC mechanisms, across tetragonal to monoclinic phase transformation in rationally designed Er doped ZrO2 nanoparticles. Rare evidence of a heterogeneous dopant distribution leading to the coexistence of two polymorphs in a single nanoparticle is revealed by Z- and phase contrast transmission electron microscopy (TEM). Despite their spatial proximity, Er in the two polymorphs are spectroscopically isolated, i.e. they do not communicate by energy transfer. Segregated Er, which is well imaged in TEM, is absent in UPC, while the minor phase content overlooked by X-ray diffraction and TEM is revealed by UPC. The outstanding sensitivity of combined TEM and UPC emission to subtle deviations from uniform doping in the diluted concentration regime renders such an approach relevant for various functional oxides supporting lanthanide dopants as emitters.

Behavior of Molybdenum⁻Vanadium Mixed Oxides in Selective Oxidation and Disproportionation of Toluene.

This study deals with the behavior of molybdenum⁻vanadium (Mo/V) mixed oxides catalysts in both disproportionation and selective oxidation of toluene. Samples containing different Mo/V ratios were prepared by a modified method using tetradecyltrimethylammonium bromide and acetic acid. The catalysts were characterized using several techniques: nitrogen adsorption⁻desorption isotherms, X-Ray diffraction (XRD), ammonia temperature-programmed desorption (TPD-NH3), temperature-programmed reduction by hydrogen (H2-TPR), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, Fourier-transform infrared-spectroscopy (FTIR) and ultraviolet-visible spectroscopies (UV⁻VIS). The XRD results evidenced the presence of orthorhombic α-MoO3 and V2O5 phases, as well as monoclinic ß-MoO3 and V2MoO8 phases, their abundance depending on the Mo to V ratio, while the TPD-NH3 emphasized that, the total amount of the acid sites diminished with the increase of the Mo loading. The TPR investigations indicated that the samples with higher Mo/V ratio possess a higher reducibility. The main findings of this study led to the conclusion that the presence of strong acid sites afforded a high conversion in toluene disproportionation (Mo/V = 1), while a higher reducibility is a prerequisite to accomplishing high conversion in toluene oxidation (Mo/V = 2). The catalyst with Mo/V = 1 acquires the best yield to xylenes from the toluene disproportionation reaction, while the catalyst with Mo/V = 0.33 presents the highest yield to benzaldehyde.

Bulk Versus Surface Modification of Alumina with Mn and Ce Based Oxides for CH4 Catalytic Combustion.

This study presents the synthesis and characterization of lanthanum-modified alumina supported cerium-manganese mixed oxides, which were prepared by three different methods (coprecipitation, impregnation and citrate-based sol-gel method) followed by calcination at 500 °C. The physicochemical properties of the synthesized materials were investigated by various characterization techniques, namely: nitrogen adsorption-desorption isotherms, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and H2-temperature programmed reduction (TPR). This experimental study demonstrated that the role of the catalytic surface is much more important than the bulk one. Indeed, the incipient impregnation of CeO2-MnOx catalyst, supported on an optimized amount of 4 wt.% La2O3-Al2O3, provided the best results of the catalytic combustion of methane on our catalytic micro-convertors. This is mainly due to: (i) the highest pore size dimensions according to the Brunauer-Emmett-Teller (BET) investigations, (ii) the highest amount of Mn4+ or/and Ce4+ on the surface as revealed by XPS, (iii) the presence of a mixed phase (Ce2MnO6) as shown by X-ray diffraction; and (iv) a higher reducibility of Mn4+ or/and Ce4+ species as displayed by H2-TPR and therefore more reactive oxygen species.

Heavy doping of ceria by wet impregnation: a viable alternative to bulk doping approaches.

To avoid the deleterious effects of dopant segregation, synthesis methods that facilitate a homogenous dopant distribution in the ceria lattice were employed. Though doping ceria by wet impregnation was also credited to induce a homogeneous solid solution even in the heavy regime (concentration ≥20%, A. Corma, P. Atienzar, H. Garcia and J. Chane-Ching, Nat. Mater., 2004, 3, 394-397), no follow up investigation has been reported. Herein, we investigated ceria nanoparticles (1%Tm-CeO2 and 1%Eu-CeO2) wet-impregnated with trivalent rare-earth (Yb, 20%), bivalent (Ca, 20%) and isovalent (Zr, 30%) metals, followed by annealing in air. Homogeneity of the solid solutions of Yb-impregnated ceria was confirmed by a two-feature characterization toolbox that included X-ray diffraction, Raman spectroscopy, transmission electron microscopy, as well as up-conversion emission as a probe tool. Since the up-conversion emission of Tm was not detectable in the absence of Yb while its efficiency depends on the average distance between Yb and Tm ions, the Yb incorporation and its migration from the surface to the lattice bulk sites in wet-impregnated ceria can be "visualized" and compared with that of the Yb bulk-doped counterpart. The use of Eu luminescence as a local probe confirmed the homogeneity of solid solutions of Ca and Zr-impregnated ceria and also sustained the opposite roles of Ca and Zr as the repeller and the scavenger of oxygen vacancies, respectively. All these results suggested that heavy doping of ceria by wet impregnation with metals with +2, +3 and +4 valencies represent a facile alternative to conventional doping approaches. Therefore, the effects of the amount and the type of metal dopant on the structural properties of CeO2 could be investigated in a more systematic and probably a more reproducible manner, which would significantly increase the potential of ceria in catalysis and other applications.