Amine coupling versus biotin capture for the assessment of sulfonamide as ligands of hCA isoforms.

This work was dedicated to the development of a reliable SPR method allowing the simultaneous and quick determination of the affinity and selectivity of designed sulfonamide derivatives for hCAIX and hCAXII versus hCAII, in order to provide an efficient tool to discover drugs for anticancer therapy of solid tumors. We performed for the first time a comparison of two immobilization approaches of hCA isoforms. First one relies on the use of an amine coupling strategy, using a CM7 chip to obtain higher immobilization levels than with a CM5 chip and consequently the affinity with an higher precision (CV% < 10%). The second corresponds to a capture of proteins on a streptavidin chip, named CAP chip, after optimization of biotinylation conditions (amine versus carboxyl coupling, biotin to protein ratio). Thanks to the amine coupling approach, only hCAII and hCAXII isoforms were efficiently biotinylated to reach relevant immobilization (3000 RU and 2700 RU, respectively) to perform affinity studies. For hCAIX, despite a successful biotinylation, capture on the CAP chip was a failure. Finally, concordance between affinities obtained for the three derivatives to CAs isozymes on both chips has allowed to valid the approaches for a further screening of new derivatives.

Control of natural transformation in salivarius Streptococci through specific degradation of σX by the MecA-ClpCP protease complex.

Competence for natural DNA transformation is a tightly controlled developmental process in streptococci. In mutans and salivarius species, the abundance of the central competence regulator σ(X) is regulated at two levels: transcriptional, by the ComRS signaling system via the σ(X)/ComX/SigX-inducing peptide (XIP), and posttranscriptional, by the adaptor protein MecA and its associated Clp ATPase, ClpC. In this study, we further investigated the mechanism and function of the MecA-ClpC control system in the salivarius species Streptococcus thermophilus. Using in vitro approaches, we showed that MecA specifically interacts with both σ(X) and ClpC, suggesting the formation of a ternary σ(X)-MecA-ClpC complex. Moreover, we demonstrated that MecA ultimately targets σ(X) for its degradation by the ClpCP protease in an ATP-dependent manner. We also identify a short sequence (18 amino acids) in the N-terminal domain of σ(X) as essential for the interaction with MecA and subsequent σ(X) degradation. Finally, increased transformability of a MecA-deficient strain in the presence of subinducing XIP concentrations suggests that the MecA-ClpCP proteolytic complex acts as an additional locking device to prevent competence under inappropriate conditions. A model of the interplay between ComRS and MecA-ClpCP in the control of σ(X) activity is proposed.

Label-free characterization of carbonic anhydrase-novel inhibitor interactions using surface plasmon resonance, isothermal titration calorimetry and fluorescence-based thermal shift assays.

This work describes the development of biophysical unbiased methods to study the interactions between new designed compounds and carbonic anhydrase II (CAII) enzyme. These methods have to permit both a screening of a series of sulfonamide derivatives and the identification of a lead compound after a thorough study of the most promising molecules. Interactions data were collected using surface plasmon resonance (SPR) and thermal shift assay (TSA). In the first step, experiments were performed with bovine CAII isoform and were extended to human CAII. Isothermal titration calorimetry (ITC) experiments were also conducted to obtain thermodynamics parameters necessary for the processing of the TSA data. Results obtained with this reference methodology demonstrate the effectiveness of SPR and TSA. KD values obtained from SPR data were in perfect accordance with ITC. For TSA, despite the fact that the absolute values of KD were quite different, the same affinity scale was obtained for all compounds. The binding affinities of the analytes studied vary by more than 50 orders of magnitude; for example, the KD value determined by SPR were 6 ± 4 and 299 ± 25 nM for compounds 1 and 3, respectively. This paper discusses some of the theoretical and experimental aspects of the affinity-based methods and evaluates the protein consumption to develop methods for the screening of further new compounds. The double interest of SPR, that is, for screening and for the quick thorough study of the interactions parameters (ka , kd , and KD ), leads us to choose this methodology for the study of new potential inhibitors.

Optimization of the enantioseparation of a diaryl-pyrazole sulfonamide derivative by capillary electrophoresis in a dual CD mode using experimental design.

A CE method using dual cationic and neutral cyclodextrins (CD) was optimized for the enantiomeric separation of a compound presenting a diaryl sulfonamide group. Preliminary studies were made to select the optimal CDs and pH of the BGE. Two CDs (amino-ß-CD and ß-CD) were selected to separate the enantiomers in a 67 mM phosphate buffer at pH 7.4. However, the repeatability of the analyses obtained on bare-fused silica capillary was not acceptable owing to the adsorption of the amino-ß-CD to the capillary. To prevent this, a dynamic coating of the capillary was used employing five layers of ionic-polymer (poly(diallyldimethylammonium) chloride (PDADMAC) and poly(sodium 4-styrenesulfonate). The efficiency of the coating was assessed by measuring the EOF stability. Repeatability of the injections was obtained when intermediate coating with PDADMAC was performed between each run. Secondly, this enantioseparation method was optimized using a central composite circumscribed design including three factors: amino-ß-CD and ß-CD concentrations and the percentage of methanol. Under the optimal conditions (i.e. 16.6 mM of amino-ß-CD, 2.6 mM of ß-CD, 0% MeOH in 67 mM phosphate buffer (pH 7.4) as BGE, cathodic injection 0.5 psi, 5 s, separation voltage 15 kV and a temperature of 15°C), complete enantioresolution of the analyte was obtained. It is worth mentioning that the design of experiments (DOE) protocol employed showed a significant interaction between CDs, highlighting the utility of DOE in method development. Finally, small variations in the ionic-polymer concentrations did not significantly influence the EOF, confirming the robustness of the coating method.

New selective carbonic anhydrase IX inhibitors: synthesis and pharmacological evaluation of diarylpyrazole-benzenesulfonamides.

Carbonic anhydrase (CA) IX expression is increased upon hypoxia and has been proposed as a therapeutic target since it has been associated with poor prognosis, tumor progression and pH regulation. We report the synthesis and the pharmacological evaluation of a new class of human carbonic anhydrase (hCA) inhibitors, 4-(5-aryl-2-hydroxymethyl-pyrazol-1-yl)-benzenesulfonamides. A molecular modeling study was conducted in order to simulate the binding mode of this new family of enzyme inhibitors within the active site of hCA IX. Pharmacological studies revealed high hCA IX inhibitory potency in the parameters nanomolar range. This study showed that the position of sulfonamide group in meta of the 1-phenylpyrazole increase a selectivity hCA IX versus hCA II of our compounds. An in vitro antiproliferative screening has been performed on the breast cancer MDA-MB-231 cell using doxorubicin as cytotoxic agent and in presence of selected CA IX inhibitor. The results shown that the cytotoxic efficiency of doxorubicin in an hypoxic environment, expressed in IC50 value, is restored at 20% level with 1µM CA IX inhibitor.

Behavior of Regular Insulin in a Parenteral Nutrition Admixture: Validation of an LC/MS-MS Assay and the In Vitro Evaluation of Insulin Glycation.

Parenteral-nutrition (PN)-induced hyperglycemia increases morbidity and mortality and must be treated with insulin. Unfortunately, the addition of insulin to a ternary PN admixture leads to a rapid decrease in insulin content. Our study's objective was to determine the mechanistic basis of insulin's disappearance. The literature data suggested the presence of a glycation reaction; we therefore validated an LC-MS/MS assay for insulin and glycated insulin. In a 24-h stability study, 20 IU/L of insulin was added to a binary PN admixture at pH 3.6 or 6.3. When the samples were diluted before analysis with a near-neutral diluent, insulin was fully stable at pH 3.6, while a loss of around 50% was observed at pH 6.3. Its disappearance was shown to be inversely correlated with the appearance of monoglycated insulin (probably a Schiff base adduct). Monoglycated insulin might also undergo a back-reaction to form insulin after acidic dilution. Furthermore, a second monoglycated insulin species appeared in the PN admixture after more than 24 h at high temperature (40 °C) and a high insulin concentration (1000 IU/L). It was stable at acidic pH and might be an Amadori product. The impact of insulin glycation under non-forced conditions on insulin's bioactivity requires further investigation.

Heat-based transdermal delivery of a ramipril loaded cream for treating hypertension.

Angiotensin-converting enzyme (ACE) inhibitors play an important role in the development of anti-hypertension approaches, with ramipril being one of the most widely used ACE inhibitor prodrugs orally administered once or twice a day. Due to its low bioavailability, large amounts have to be administered to obtain a therapeutic effect. In this work, we propose a ramipril loaded pharmaceutical formulation in contact with an electrothermal actuator based on a gold nanohole array as an efficient approach to increase the transdermal ramipril flux. Using rats as an in vivo model, the effect on the systolic and diastolic blood pressure is evaluated, showing that under optimized conditions the blood pressure could be regulated. Heat activation resulted in total drug delivery out of a bandage loaded with 1 mg ramipril, revealing a flux of 50.9 ± 2.8 µg cm-2 h-1. Importantly, heat-based transdermal dispensing allowed efficient and rapid delivery of ramipril in spontaneously hypertensive rats, with its active form (ramiprilat) detected in blood as early as 5 minutes after delivery onset, accompanied by significant decrease in blood pressure.

A multivariate approach for the determination of isoelectric point of human carbonic anhydrase isoforms by capillary isoelectric focusing.

Human carbonic anhydrase (hCA) IX and XII are isoenzymes which are highly overexpressed in many cancer types. Recently, it has been shown that hCA IX contributes to the acidification of the tumor environment leading to chemoresistance with basic antitumoral drugs. The development of selective hCA inhibitors constitutes a new therapeutic axis. In order to elucidate the specific interactions between hCA and inhibitors, physico-chemical properties of hCA must be evaluated. This work reports the determination of the isoelectric point (pI) of a series of hCA isoforms by capillary isoelectric focusing. First, the method was optimized with synthetic UV-detectable pI markers using a central composite design. The separation was performed in a fused-silica capillary chemically derivatized with hydroxypropylcellulose and using a glycerol-water medium as the anticonvective gel. Three main factors (ampholyte content, focusing time and mobilization pressure) were optimized in order to obtain the best resolution, detection threshold and precision on the pI determination. Then, the model was validated through the analysis of standard proteins mixture having known pI values, before investigating the pI of hCA isoforms.

Capillary electrophoresis as a versatile tool for quality control and epidermis permeation studies of transdermal formulations.

Capillary electrophoresis has been investigated to evaluate the performances of new transdermal formulations containing antiemetics. After optimization of the background electrolyte (sodium phosphate buffer (pH 2.5; 60 mM) containing 12% of ethanol (v/v)), domperidone, diphenhydramine, haloperidol, metoclopramide and promethazine were base-line resolved in 10 min. After hydrodynamic injection of the sample (0.5 psi for 7 s), the method was fully validated through the build of the accuracy profile. Trueness values ranged from -1.85 and 5.43% and relative standard deviation of intra-day and inter-day precision was lower than 6.20%. This method was found convenient for quality control of extemporaneous ready-to-use transdermal formulations with recoveries ranging from 91.2-107.8%. However, using hydrodynamic injection, limits of quantitation in the 0.3-2.6 µg.mL-1 range, were not low enough to evaluate the permeation rate of antimetics through epidermis. Field amplified sample injection was used to improve both sensitivity and quantitation thresholds. Several parameters (nature and concentration of the protonation agent, composition of the injected solvent, applied voltage and duration of the injection) have been optimized using a multivariate approach. In the optimized conditions, signal-to-noise ratios were improved by a 600- to 2000-fold factor, regarding the antiemetic. However, the presence of salts in the simulated body fluid solution, used as receptor medium to perform permeation kinetic study, was improper to allow the stacking effect. Therefore, a liquid-liquid extraction has been developed and applied on simulated body fluid solution. Finally, this new method has been shown strongly useful to evaluate the permeation kinetic of metoclopramide through pig epidermis.

Analysis of Phthalates and Alternative Plasticizers in Gloves by Gas Chromatography-Mass Spectrometry and Liquid Chromatography-UV Detection: A Comparative Study.

Gloves represent an essential feature for hand protection because it is a requirement in the professional framework to comply with both hand hygiene standards and the principles of good laboratory practice. Despite their wide use, there is a knowledge gap regarding their composition, including phthalates. The purpose of the present study was to develop two orthogonal methods, GC-MS and HPLC-DAD, for the screening of plasticizers in gloves. Performances of these two methods were compared in terms of ease of use, number of analyzed plasticizers, and sample preparation. The two methods were validated and applied for the identification and quantification of plasticizers in ten gloves made with different materials (vinyl, nitrile, latex, and neoprene). Results revealed the presence of three main ones: DEHP, DEHT, and DINP. Additionally, the contents of plasticizers were extremely variable, depending on the glove material. As expected, the results point out a predominant use of plasticizers in vinyl gloves with an amount that should be of concern. While DEHP is classified as a toxic substance for reproduction 1B, it was, however, quantified in the ten different glove samples studied. This study provides new data regarding the plasticizers' content in protective gloves, which could be useful for risk assessment.

Design, solid-phase synthesis, and biological evaluation of novel 1,5-diarylpyrrole-3-carboxamides as carbonic anhydrase IX inhibitors.

Following previous studies we herein report the synthesis and the pharmacological evaluation of a new class of human carbonic anhydrase (hCA) inhibitors, 1,5-diarylpyrrole-3-carboxamides prepared by a solid-phase strategy involving a PS(HOBt) resin. A molecular modeling study was conducted in order to simulate the binding mode of this new family of enzyme inhibitors within the active site of hCA IX. This study revealed that the 3-position of the pyrrole was opened to the solvent, so we introduced an amino side-chain, protonated at physiological pH both to enhance the aqueous solubility and to decrease the cell membrane penetration. This strategy consisted of preparing membrane-impermeant inhibitors that may selectively target the tumor-associated hCA IX. Physico-chemical characterizations including aqueous solubility and lipophilic parameters are described. Pharmacological studies revealed high hCA IX inhibitory potency in the nanomolar range. Some compounds are selective for hCA IX displaying hCA I/hCA IX and hCA II/hCA IX ratios higher than 20 and 5, respectively.

Determination of the stoichiometry between a drug and its counter-ion by supercritical fluid chromatography using ultra-violet and evaporative light scattering detections: Application to ondansetron hydrochloride.

In this paper, a supercritical fluid chromatography method using ultra-violet and evaporative light scattering detections (SFC-UV/ELSD) has been developed and validated for the stoichiometry determination of an antiemetic drug with its counter-ion i.e. ondansetron hydrochloride. Seven stationary phases were first screened using a CO2-methanol-diethylamine mobile phase. Best conditions were determined using Derringer's desirability functions regarding chromatographic separation: selectivity, resolution, peak shape and runtime. The influence of co-solvent composition on resolution was evaluated. After optimization, best chromatographic results were obtained using 2-ethylpyridine stationary phase and a co-solvent composed of 0.2% diethylamine and 2% water in methanol. While ondansetron was quantified using UV detection (214 nm) and an external calibration curve, the determination of chloride was carried out using ELSD and an internal calibration curve. Then, the method was validated using the accuracy profile approach with a total error included in the ±10%. Finally, the proposed method was applied for the determination of the molar ratio between ondansetron and chloride. A value of 1.001 ± 0.003 demonstrated that the stoichiometry of this drug with its counter-ion was 1:1.

Publisher Correction: MUC4-ErbB2 Oncogenic Complex: Binding studies using Microscale Thermophoresis.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

Determination of acetaminophen and its main metabolites in urine by capillary electrophoresis hyphenated to mass spectrometry.

In this study, a capillary electrophoresis-tandem mass spectrometry method combining efficient separation and sensitive detection has been developed and validated, for the first time, to quantify acetaminophen and five of its metabolites in urine samples. Optimization of the method has led us to perform detection in positive ESI mode using MeOH-ammonium hydroxide (0.1%) (50:50, v/v) as sheath liquid. Moreover, optimal separation has been obtained in less than 9 min after anodic injection, using an ammonium acetate solution (40 mM, pH 10) as BGE. It was shown that the dilution solvent and the dilution factor to use for sample preparation are critical parameters to avoid peak splitting, to gain in sensitivity and then to obtain an effective analysis method. While a 200-fold factor dilution was shown to be suitable for quantitation of acetaminophen, acetaminophen mercapturate, acetaminophen sulfate and acetaminophen glucuronide, a 20-fold dilution was finally selected for methoxy-acetaminophen and 3-methylthioacetaminophen analysis, thus requiring two successive analyses to be carried out in order to quantify all metabolites. Hyphenation of CE with MS/MS versus UV permits to improve LOQ (10-20-fold factor with respect to previous works for acetaminophen, acetaminophen sulfate and acetaminophen glucuronide). Moreover, use of CE versus HPLC, permits to quantify two additional metabolites, i.e. 3-methylthio-acetaminophen and methoxy-acetaminophen. The method has been validated using the accuracy profile approach with a total error (accuracy) included in the ± 20% range. Thereby, the method allows the quantitation of acetaminophen and acetaminophen mercapturate in the range (0.1-1 mg mL-1), and of acetaminophen sulfate, methoxy-acetaminophen, acetaminophen glutathione and 3-methylthio-acetaminophen in the ranges (0.5-5 mg mL-1), (0.025-0.4 mg mL-1), (9.22-30 mg mL-1) and (0.073-0.4 mg mL-1), respectively. The method was finally applied to the analysis of urine samples of eighteen patients belonging to three different inclusion groups of the ongoing clinical trial, demonstrating that the method is suitable to highlight different metabolic profiles. This work will be subsequently extended to the analysis two hundred and seventy urine samples from patients included in a clinical trial dedicated to the study of acetaminophen metabolism changes after hepatic resection.

MUC4-ErbB2 Oncogenic Complex: Binding studies using Microscale Thermophoresis.

The MUC4 membrane-bound mucin is a large O-glycoprotein involved in epithelial homeostasis. At the cancer cell surface MUC4 interacts with ErbB2 receptor via EGF domains to promote cell proliferation and migration. MUC4 is highly regarded as a therapeutic target in pancreatic cancer as it is not expressed in healthy pancreas, while it is neoexpressed in early preneoplastic stages (PanINs). However, the association/dissociation constant of MUC4-ErbB2 complex is unknown. Protein-protein interactions (PPIs) have become a major area of research in the past years and the characterization of their interactions, especially by biophysical methods, is intensively used in drug discovery. To characterize the MUC4-ErbB2 interaction, we used MicroScale Thermophoresis (MST), a powerful method for quantitative protein interaction analysis under challenging conditions. We worked with CHO cell lysates containing either the transmembrane ß subunit of MUC4 (MUC4ß) or a truncated mutant encompassing only the EGF domains (MUC4EGF3+1+2). MST studies have led to the characterization of equilibrium dissociation constants (Kd) for MUC4ß-ErbB2 (7-25 nM) and MUC4EGF3+1+2/ErbB2 (65-79 nM) complexes. This work provides new information regarding the MUC4-ErbB2 interaction at the biophysical level and also confirms that the presence of the three EGF domains of MUC4 is sufficient to provide efficient interaction. This technological approach will be very useful in the future to validate small molecule binding affinities targeting MUC4-ErbB2 complex for drug discovery development in cancer. It will also be of high interest for the other known membrane mucins forming oncogenic complexes with ErbBs at the cancer cell surface.

Simultaneous determination of inorganic anions and cations by supercritical fluid chromatography using evaporative light scattering detection.

Supercritical fluid chromatography (SFC) is commonly used for the analysis of non-polar compounds, but remains poorly explored for the separation of polar and ionized molecules. In this paper, SFC has been investigated for the separation of 14 inorganic ions sampled in aqueous solutions. Four polar stationary phases were first screened using CO2-methanol-based mobile phases containing water or different acidic or basic additives, in order to select the most efficient conditions for the simultaneous retention of inorganic cations and anions and to favor their detection using evaporative light scattering detector (ELSD). Orthogonal selectivity was obtained depending on the stationary phase used: whereas anions are less retained on HILIC stationary phase, 2-ethylpyridine (2-EP) stationary phase exhibits strong interaction for anions. Best results were obtained under gradient elution mode using a 2-EP stationary phase and by adding 0.2% triethylamine in the CO2-methanol-based mobile phase. The composition of the injection solvent was also investigated. The results showed that a methanolic sample containing a percentage of water not exceeding 20% does not affect the analytical performances obtained on 2-EP. Moreover, the presence of triethylamine in the injection solvent contributes to eliminate peaks shoulders. Among the 14 inorganic ions tested, three cations (Li+, Ca2+ and Mg2+) and five anions (Cl-, Br-, NO3-, I-, SCN-) were totally resolved in 15 min. NO3- and NO2- still coeluted in the final optimized conditions. The other investigated ions were either strongly retained on the stationary phase or not detected by the ELSD.

Toward the Discovery of a Novel Class of YAP⁻TEAD Interaction Inhibitors by Virtual Screening Approach Targeting YAP⁻TEAD Protein⁻Protein Interface.

Intrinsically disordered protein YAP (yes-associated protein) interacts with TEADs transcriptional factors family (transcriptional enhancer associated domain) creating three interfaces. Interface 3, between the Ω-loop of YAP and a shallow pocket of TEAD was identified as the most important TEAD zone for YAP-TEAD interaction. Using the first X-ray structure of the hYAP50⁻71-hTEAD1209⁻426 complex (PDB 3KYS) published in 2010, a protein-protein interaction inhibitors-enriched library (175,000 chemical compounds) was screened against this hydrophobic pocket of TEAD. Four different chemical families have been identified and evaluated using biophysical techniques (thermal shift assay, microscale thermophoresis) and in cellulo assays (luciferase activity in transfected HEK293 cells, RTqPCR in MDA-MB231 cells). A first promising hit with micromolar inhibition in the luciferase gene reporter assay was discovered. This hit also decreased mRNA levels of TEAD target genes.

Photothermally triggered on-demand insulin release from reduced graphene oxide modified hydrogels.

On-demand delivery of therapeutics plays an essential role in simplifying and improving patient care. The high loading capacity of reduced graphene oxide (rGO) for drugs has made this matrix of particular interest for its hybridization with therapeutics. In this work, we describe the formulation of rGO impregnated poly(ethylene glycol) dimethacrylate based hydrogels (PEGDMA-rGO) and their efficient loading with insulin. Near-infrared (NIR) light induced heating of the PEGDMA-rGO hydrogels allows for highly efficient insulin release. Most importantly, we validate that the NIR irradiation of the hydrogel has no effect on the biological and metabolic activities of the released insulin. The ease of insulin loading/reloading makes this photothermally triggered release strategy of interest for diabetic patients. Additionally, the rGO-based protein releasing platform fabricated here can be expanded towards 'on demand' release of various other therapeutically relevant biomolecules.

Transdermal skin patch based on reduced graphene oxide: A new approach for photothermal triggered permeation of ondansetron across porcine skin.

The development of a skin-mounted patch capable of controlled transcutaneous delivery of therapeutics through thermal activation provides a unique solution for the controlled release of active principles over long-term periods. Here, we report on a flexible transdermal patch for photothermal triggered release of ondansetron (ODS), a commonly used drug for the treatment of chemotherapy-induced nausea and vomiting and used as model compound here. To achieve this, a dispersion of ODS-loaded reduced graphene oxide (rGO-ODS) nanosheets were deposited onto Kapton to produce a flexible polyimide-based patch. It is demonstrated that ODS loaded Kapton/rGO patches have a high drug delivery performance upon irradiation with a continuous laser beam at 980nm for 10min due to an induced photothermal heating effect. The ability of ODS impregnated Kapton/rGO patches as transdermal delivery scaffolds for ODS across the skin is in addition investigated using porcine ear skin as a model. We show that the cumulative quantity and flux of ODS passing the skin are highly depending on the laser power density used. At 5Wcm-2 irradiation, the ODS flux across pig skin was determined to be 1.6µgcm-2h-1 comparable to other approaches. The use of tween 20 as skin enhancer could significantly increase the ODS flux to 13.2µgcm-2h-1. While the skin penetration enhancement is comparable to that obtained using other well-known permeation enhancers, the actual superiority and interest of the proposed approach is that the Kapton/rGO photoactivatable skin patch can be loaded with any drugs and therapeutics of interest, making the approach extremely versatile. The on demand delivery of drugs upon local laser irradiation and the possibility to reload the interface with the drug makes this new drug administration route very appealing.

Chiral separation of new sulfonamide derivatives and evaluation of their enantioselective affinity for human carbonic anhydrase II by microscale thermophoresis and surface plasmon resonance.

The aim of this study was to develop a method combining chiral separation and biophysical techniques to evaluate the enantioselective affinity of original sulfonamide derivatives towards their therapeutic target, the human carbonic anhydrase II (hACII). The first step consisted in the preparation of the enantiomers by chromatographic separation. The performances of HPLC and Supercritical Fluid Chromatography (SFC) were studied at the analytical scale by optimization of various experimental conditions using adsorbed polysaccharide chiral stationary phases (amylose AD-H and cellulose OD-H). Since SFC allowed obtaining higher enantioresolutions per time unit, it was selected for the semi-preparative scale and successfully used to isolate each enantiomer with a satisfactory enantiomeric purity (>98%). Secondly, microscale thermophoresis (MST) method and surface plasmon resonance (SPR) used as reference method were developed to measure potential enantioselective affinities of these enantiomers towards the hACII. The optimizations of both methods were performed using a reference compound, i.e. acetazolamide, which affinity for hCAII has previously been demonstrated. For all compounds, KD values obtained using MST and SPR were in good agreement, leading to similar affinity scales despite both approaches totally differ (labeling for MST versus immobilization of the protein for SPR). The equilibrium dissociation constants of our original compounds for the hCAII were in the range 100-1000nM and an enantioselectivity was observed using the MST and SPR methods for the diarylpyrazole 2. Finally, by comparing the MST and SPR techniques, MST appears especially adapted for further screening of a series of sulfonamide derivatives due to the lower time required to estimate a binding constant while consuming as little hCAII as SPR.