Nylon Fabric/GO Based Self-Powered Humidity Sensor Based on the Galvanic Cell Principle with High Air Permeability and Rapid-Response.

Flexible humidity sensors have received more and more attention in people's lives, and the problems of gas permeability and power supply issues of the device have long been areas in need of improvement. In this work, inspired by the high air permeability of daily wear clothing and galvanic batteries, a self-powered humidity sensor with high air permeability and fast response is designed. A nylon fabric/GO net (as a humidity sensitive layer and solid electrolyte) is obtained by spraying technique. This structure enables the sensor to have fast response/recovery (0.78 s/0.93 s, calculated at 90% of the final value), ultra-high response (0.83 V) and excellent stability (over 150 cycles) at 35 °C. Such sensors are useful for health monitoring, such as non-contact monitoring of human respiratory rate before and after exercise, and monitoring a level of humidity in the palms, arms, and fingers. This research provides an idea for developing a flexible wearable humidity sensor that is both breathable and self-powered and can also be mass-produced similar to wearable clothing.

Extraordinary Five-Wave Mixing in a Zinc Oxide Microwire on a Au Film.

Coherent multiwave mixing is in demand for optical frequency conversion, imaging, quantum information science, etc., but has rarely been demonstrated in solid-state systems. Here, we observed three- and five-wave mixing (5WM) in a c-axis growth zinc oxide microwire on a Au film with picosecond pulses in the near-infrared region. An output 5WM of 4.7 × 10-7 µW, only 2-3 orders smaller than the three-wave mixing, is achieved when the excitation power is as low as 1.5 mW and the peak power density as weak as ∼107 W/cm2. The excitation power dependence of 5WM agrees well with the perturbation limit under the low intensity but exhibits a strong deviation at a high pumping power. This extraordinary behavior is attributed to the cooperative resonant enhancement effect when pumping in the near-infrared range. Our study offers a potential solid-state platform for on-chip multiwave mixing and quantum nonlinear optics, such as generating many-photon entangled states or the construction of photon-photon quantum logic gates.

3D Porous Structure in MXene/PANI Foam for a High-Performance Flexible Pressure Sensor.

The fields of electronic skin, man-machine interaction, and health monitoring require flexible pressure sensors with great sensitivity. However, most microstructure designs utilized to fabricate high-performance pressure sensors require complex preparation processes. Here, MXene/polyaniline (PANI) foam with 3D porous structure is achieved by using a steam-induced foaming method. Based on the structure, a flexible piezoresistive sensor is fabricated. It exhibits high sensitivity (690.91 kPa-1 ), rapid response, and recovery times (106/95 ms) and outstanding fatigue resistance properties (10 000 cycles). The MXene/PANI foam-based pressure sensor can swiftly detect minor pressure and be further used for human activity and health monitoring.

Study of the Growth Mechanism of Solution-Synthesized Symmetric Tellurium Nanoflakes at Atomic Resolution.

As a new member of 2D materials, 2D tellurium (Te) has recently attracted much attention due to its intriguing properties. Through hydrothermal processing, 2D Te with tunable thickness and size has been realized, and its growth mechanism has also been studied. However, the tailored growth of 2D Te nanoflakes with symmetrical morphologies and interfacial moiré fringes has never been reported. Here, 2D Te nanoflakes have been prepared using the hydrothermal method, and mirror-symmetrical shapes (including "V-shape," "heart-shape," and "paper airplane-shape") with obvious moiré fringes in the middle of the nanoflakes are observed. Comprehensive transmission electron microscopy (TEM) techniques are utilized for structural characterization of these nanoflakes, especially the moiré fringes in the symmetry axis region of the nanoflakes. The systematic analyses of the moiré fringes and the observation of obvious overlapping edges of the composing nanoflakes from the cross-sectional samples reveal the possible mechanism of morphological evolution for these symmetrical nanoflakes. These details may fill the research gap in the controllable growth of 2D Te nanomaterials, pave the way for the fabrication of 2D Te moiré superlattices and in-plane homojunctions, and promote their future versatile applications.

Positive and negative photoconductivity characteristics in CsPbBr3/graphene heterojunction.

Broadband response photodetectors have received great research interest in optical sensing field. Usually, materials with positive photoconductivity (PPC) are general and the lack of negative photoconductivity (NPC) materials limits the application of photoelectric effect, especially in the broadband photodetecting field. Therefore, the finding of NPC materials is very important. Integrating PPC and NPC response into a single device is extremely meaningful to the development of broadband photodetector. In this work, we fabricated CsPbBr3 nanocrystals (NCs)-multilayered graphene heterojunction, which achieved persistent NPC response to ultra violet (300-390 nm) and PPC response to visible light (420-510 nm). The persistent NPC relies on the desorption of H2O vapor, and varies its intensity with the power intensity of laser. The PPC relies on the holes transmission from NCs to graphene. The recombination of NPC and PPC effect provides background knowledge for the development of broadband photodetector.

Tensible and flexible high-sensitive spandex fiber strain sensor enhanced by carbon nanotubes/Ag nanoparticles.

Although the wearable strain sensors have received extensive research interest in recent years, it remains a huge challenge conforming the requirements in both of ultrahigh stretchability and high strain coefficient (gauge factor). Herein, a stretchable and flexible spandex fiber strain sensor coupled with carbon nanotubes (CNTs)/Ag nanoparticles (Ag NPs) that assembled through an efficient and large-scale layer-by layer self-assembly is presented. To ensure CNTs and Ag NPs can attach well to the spandex fiber without falling off, achieving high sensitivity under large tensile, sodium dodecyl benzene sulfonate, polyvinyl alcohol, and polystyrene sulfonic acid are introduced to improve the adhesion via the molecular entanglement and other interactions between them. Consequently, the strain sensor exhibits remarkable performance, such as an ultrahigh gauge factor of 58.5 in the low-strain range from 0% to 20%, a wide strain range (0%-200%), a fast response time of 42 ms and good working stability (>5000 stretching-releasing cycles). Subsequently, detailed mechanism of the sensor and its use in full range of human motion monitoring are further studied. It is worth noting that with the distinctive mechanism and structure, the special spandex fiber sensor is able to monitor minimum strain as low as 0.053%, showing tremendous prospect for the field of smart fabrics and wearable health care devices.

Atomically Thin Oxyhalide Solar-Blind Photodetectors.

2D wide-bandgap semiconductors demonstrate great potential in fabricating solar-blind ultraviolet (SBUV) photodetectors. However, the low responsivity of 2D solar-blind photodetectors still limits their practical applications. Here, high-responsivity solar-blind photodetectors are achieved based on 2D bismuth oxychloride (BiOCl) flakes. The 2D BiOCl photodetectors exhibit a responsivity up to 35.7 A W-1 and a specific detectivity of 2.2 × 1010 Jones under 250 nm illumination with 17.8 µW cm-2 power density. In particular, the enhanced photodetective performances are demonstrated in BiOCl photodetectors with increasing ambient temperature. Surprisingly, their responsivity can reach 2060 A W-1 at 450 K under solar-blind light illumination, maybe owing to the formation of defective BiOCl grains evidenced by in situ transmission electron microscopy. The high responsivity throughout the solar-blind range indicates that 2D BiOCl is a promising candidate for SBUV detection.

Study of nanometer-scale structures and electrostatic properties of InAs quantum dots decorating GaAs/AlAs core/shell nanowires.

The configurations of core/shell nanowires (NWs) and quantum dots (QDs) decorating NWs have found great applications in forming optoelectronic devices thanks to their superior performances. The combination of the two configurations would expect to bring more benefits, however, the nanometer-scale electrostatic properties of the QD/buffer layer/NW heterostructures are still unrevealed. In this study, the InAs QDs decorating GaAs/AlAs core/shell NWs are systemically studied both experimentally and theoretically. The layered atomic structures, chemical information, and anisotropic strain conditions are characterized by comprehensive transmission electron microscopy (TEM) techniques. Quantitative electron holography analyses show a large number of electrons accumulating in the InAs QD, especially at the dot apex, and charges of reversed signs and similar densities are observed to distribute at the sequential interfaces, leaving great amounts of holes in the NW core. Theoretical calculations including simulated heterostructural band structures, interfacial charge transfer, and chemical bonding analysis are in good accordance with the experimental results, and prove the important role of the AlAs buffer layer in adjusting the heterostructural band structure as well as forming stable InAs QDs on the NW surfaces. These results could be significant for achieving related optoelectronic devices with better stability and higher efficiency.

Homogeneous ZnO nanowire arrays p-n junction for blue light-emitting diode applications.

ZnO is a promising short-wavelength light-emitting materials for its wide bandgap (3.37 eV) and large exciton binding energy (∼60 meV), however, practical p-type doped ZnO is the main challenge in this field. Here, Blue light-emitting diodes (LEDs) based on the homogeneous junctions of Sb doped ZnO nanowire arrays grown on Ga doped ZnO single crystal substrate are fabricated. Element analysis, FET and Hall-effect measurements demonstrate that the Sb atom has been successfully doped into ZnO nanowires to from p-type conductivity. On the benefit of high quality of nano-size homojunction, the fabricated LED shows low turn-on voltage turn-on voltage as low as 3.4 V and strong blue emission peak located at 425 nm at room temperature, which originate from interfacial recombination of ZnO nanowire p-n homojunctions. The present blue LED based on ZnO material may have potential applications in short-wavelength optoelectronic devices.

Controlled Growth of an Mo2C-Graphene Hybrid Film as an Electrode in Self-Powered Two-Sided Mo2C-Graphene/Sb2S0.42Se2.58/TiO2 Photodetectors.

The monotonic work function of graphene makes it difficult to meet the electrode requirements of every device with different band structures. Two-dimensional (2D) transition metal carbides (TMCs), such as carbides in MXene, are considered good candidates for electrodes as a complement to graphene. Carbides in MXene have been used to make electrodes for use in devices such as lithium batteries. However, the small lateral size and thermal instability of carbides in MXene, synthesized by the chemically etching method, limit its application in optoelectronic devices. The chemical vapor deposition (CVD) method provides a new way to obtain high-quality ultrathin TMCs without functional groups. However, the TMCs film prepared by the CVD method tends to grow vertically during the growth process, which is disadvantageous for its application in the transparent electrode. Herein, we prepared an ultrathin Mo2C-graphene (Mo2C-Gr) hybrid film by CVD to solve the above problem. The work function of Mo2C-Gr is between that of graphene and a pure Mo2C film. The Mo2C-Gr hybrid film was selected as a transparent hole-transporting layer to fabricate novel Mo2C-Gr/Sb2S0.42Se2.58/TiO2 two-sided photodetectors. The Mo2C-Gr/Sb2S0.42Se2.58/TiO2/fluorine-doped tin oxide (FTO) device could detect light from both the FTO side and the Mo2C-Gr side. The device could realize a short response time (0.084 ms) and recovery time (0.100 ms). This work is believed to provide a powerful method for preparing Mo2C-graphene hybrid films and reveals its potential applications in optoelectronic devices.

In Situ TEM Observation of Crystal Structure Transformation in InAs Nanowires on Atomic Scale.

In situ transmission electron microscopy investigation of structural transformation in III-V nanowires is essential for providing direct insight into the structural stability of III-V nanowires under elevated temperature. In this study, through in situ heating investigation in a transmission electron microscope, the detailed structural transformation of InAs nanowires from wurtzite structure to zinc-blende structure at the catalyst/nanowire interface is witnessed on the atomic level. Through detailed structural and dynamic analysis, it was found that the nucleation site of each new layer of InAs and catalyst surface energy play a decisive role in the growth of the zinc-blende structure. This study provides new insights into the growth mechanism of zinc-blende-structured III-V nanowires.

Electron Holographic Study of Semiconductor Light-Emitting Diodes.

Semiconductor light-emitting diodes (LEDs), especially GaN-based heterostructures, are widely used in light illumination. The lack of inversion symmetry of wurtzite crystal structures and the lattice mismatch at heterointerfaces cause large polarization fields with contributions from both spontaneous polarization and piezoelectric polarization, which in turn results in obvious quantum confined stark effect. It is possible to alleviate this effect if the local electrostatic fields and band alignment induced charge redistribution can be quantitatively determined across the heterostructures. In this Concept, the applications of electron holography to investigate semiconductor LEDs are summarized. Following the off-axis electron holography scheme, the GaN-based LED heterostructures including InGaN/GaN-based quantum wells, other GaN-based quantum wells, and other forms of GaN-based LED materials are discussed, focusing on the local potential drops, polarization fields, and charge distributions. Moreover, GaAs-based LED heterostructures are briefly discussed. The in-line electron holography scheme emphasizes the capability of large area strain mapping across LED heterostructures with high spatial resolution and accuracy, which is combined with quantitative electrostatic measurements and other advanced transmission electron microscopy characterizations to provide an overall nanometer scale perspective of LED devices for further improvement in their electric and optical properties.

Piezoresistive Pressure Sensor Based on Synergistical Innerconnect Polyvinyl Alcohol Nanowires/Wrinkled Graphene Film.

Piezoresistive sensor is a promising pressure sensor due to its attractive advantages including uncomplicated signal collection, simple manufacture, economical and practical characteristics. Here, a flexible and highly sensitive pressure sensor based on wrinkled graphene film (WGF)/innerconnected polyvinyl alcohol (PVA) nanowires/interdigital electrodes is fabricated. Due to the synergistic effect between WGF and innerconnected PVA nanowires, the as-prepared pressure sensor realizes a high sensitivity of 28.34 kPa-1 . In addition, the device is able to discern lightweight rice about 22.4 mg (≈2.24 Pa) and shows excellent durability and reliability after 6000 repeated loading and unloading cycles. What is more, the device can detect subtle pulse beat and monitor various human movement behaviors in real-time.

Recent Progress in Micro-Supercapacitors with In-Plane Interdigital Electrode Architecture.

Due to the boom of miniaturized electronic devices in the last decade, there are great demands for ultrathin and flexible on-chip rechargeable energy storage microdevices. Supercapacitor, as one of the most hopeful appearing energy storage devices, can provide a wonderful alternative to batteries or electrolytic capacitors, owing to its fast charge and discharge rates, high power density, and long cycling stability. Especially for the recently developed micro-supercapacitors, the unique in-plane interdigital electrode architecture can fully meet the integration requirements of rapidly developed miniaturized electronic devices, and improve the power density of the unit via shortening the ionic diffusion distance between the interdigital electrodes. This concept introduces the recent advances on the design, fabrication, and application of planar micro-supercapacitors for on-chip energy storage from an overall perspective. Moreover, challenges and future development trends are discussed.

Ag nanoparticles modified large area monolayer MoS2 phototransistors with high responsivity.

Monolayer MoS2 is considered to be one of the best candidates for next generation electronics because of its ultra-thin body and direct band gap. However, MoS2 based transistors have relatively low photoresponsivity, field effect mobility and narrow response spectrum range, which hinder the application of MoS2 in optoelectronic devices. Here, based on the enhancement of localized surface plasmon resonance (LSPR), a simple method of depositing Ag nanoparticles on the MoS2 surface is used. By adjusting the size of Ag nanoparticles, the response spectral range of phototransistor is broadened from red to near ultra-violet. The photoresponsivity gains an increase of 470% up to 2.97 × 104 A W-1 at 610 nm, and the response time also shows a decrease to some extent. The enhanced responsivity is comparable to those of devices encapsulated with high-quality dielectrics, and superior over other reported monolayer MoS2 in ambient conditions. The high responsivity and working current enables a wide range of device applications. This work provides a viable route towards performance enhancement of two-dimensional phototransistors.

Enhancing light emission in flexible AC electroluminescent devices by tetrapod-like zinc oxide whiskers.

Flexible alternating current electroluminescent devices (ACEL) are more and more popular and widely used in liquid-crystal display back-lighting, large-scale architectural and decorative lighting due to their uniform light emission, low power consumption and high resolution. However, presently how to acquire high brightness under a certain voltage are confronted with challenges. Here, we demonstrate an electroluminescence (EL) enhancing strategy that tetrapod-like ZnO whiskers (T-ZnOw) are added into the bottom electrode of carbon nanotubes (CNTs) instead of phosphor layer in flexible ACEL devices emitting blue, green and orange lights, and the brightness is greatly enhanced due to the coupling between the T-ZnOw and ZnS phosphor dispersed in the flexible polydimethylsiloxane (PDMS) layer. This strategy provides a new routine for the development of high performance, flexible and large-area ACEL devices.

UV-free red electroluminescence from the cross-connected p-ZnO:Cu nanobushes/n-GaN light emitting diode.

A p-ZnO:Cu/n-GaN heterojunction light emitting diode (LED) is fabricated by growing cross-connected p-ZnO:Cu nanobushes on n-GaN film using chemical vapor deposition under oxygen-rich condition. This LED emits stable UV-free red light of 677 nm and 745 nm. The electroluminescence (EL) light of this LED is tuned from ultraviolet (UV) of ZnO/GaN to UV-free red by the electronic interfacial transition from the conduction band of n-GaN to the deep acceptor levels of p-ZnO:Cu. Both room temperature and low temperature (5K) photoluminescence spectra of ZnO:Cu indicate that the UV emission of ZnO is suppressed and the green emission is enhanced, which implies the formation of Cu-related deep levels introduced by intentionally doping Cu in ZnO. These deep levels help the EL red emission in the LED device.

Omega-3 Polyunsaturated Fatty Acids Inhibited Tumor Growth via Preventing the Decrease of Genomic DNA Methylation in Colorectal Cancer Rats.

Omge-3 polyunsaturated fatty acids (PUFAs) exhibited significant effect in inhibiting various tumors. However, the mechanisms of its anticancer role have not been fully demonstrated. The declination of 5-methylcytosine (5 mC) was closely associated with poor prognosis of tumors. To explore whether omega-3 PUFAs influences on DNA methylation level in tumors, colorectal cancer (CRC) rat model were constructed using N-methyl phosphite nitrourea and omega-3 PUFAs were fed to part of the rats during tumor induction. The PUFAs contents in the rats of 3 experimental groups were measured using gas chromatography and 5 mC level were detected by liquid chromatography tandem mass spectrometry. The results showed that tumor incidence in omega-3 treated rats was much lower than in CRC model rats, which confirmed significant antitumor role of omega-3 PUFAs. Six PUFA members categorized to omega-3 and omega-6 families were quantified and the ratio of omega-6/omega-3 PUFAs was remarkably lower in omega-3 PUFAs treatment group than in CRC model group. 5 mC content in omega-3 PUFAs treated rats was higher than in CRC model rats, suggesting omega-3 PUFAs promoted 5 mC synthesis. Therefore, omega-3 PUFAs probably inhibited tumor growth via regulating DNA methylation process, which provided a novel anticancer mechanism of omega-3 PUFAs from epigenetic view.

Enhanced photo-response properties of a single ZnO microwire photodetector by coupling effect between localized Schottky barriers and piezoelectric potential.

The coupling effect between localized Schottky barriers (SBs) and piezoelectric potential that impact the photo-response properties of a single ZnO microwire (MW) photodetector (PD) is studied. Localized SBs is introduced by Au NPs decoration. The negatively charged Au NPs deplete more carriers near the ZnO surface, which raises the SB height and sharply reduces the recover time of the PD from 142.4 s to 0.7 s. Moreover, after applying the compressive strain, the band structure of ZnO MW changes and piezoelectric potential generates, which further raises the SB height, thickens the depletion region and improves photo-response properties of the detector. The dark current is reduced by about 5 orders and its on/off current ratio increased by about 6 orders, which decreases the power consumption of the detector significantly. Under the above coupling effect between piezoelectric potential and localized SBs, the recover time of the detector is further reduced to 0.1 s ultimately. This work suggests that rational integration of localized SBs and piezoelectric potential is a viable approach to get ZnO MW PDs with high on/off ratio, ultrafast response speed and low power consumption.

Association between medical insurance type and survival in patients undergoing peritoneal dialysis.

BACKGROUND: Socioeconomic characteristics may affect the outcomes of patients treated with peritoneal dialysis (PD). There are two major medical insurances in China: the New Cooperative Medical Scheme (NCMS), mainly for rural residents, and the Urban Employees' Medical Insurance (UEMI). The aim of the present study was to assess the effect of medical insurance type on survival of patient undergoing PD. METHOD: This was a prospective study in adult patients who underwent PD at the Wuhan No.1 Hospital between January 2008 and December 2013. Patients had received continuous ambulatory PD for >3 months. Patients were divided according to their medical insurance. Demographic and socioeconomic data, biochemical parameters and primary clinical outcomes including all-cause mortality, switch to hemodialysis and kidney transplantation were analyzed. RESULT: There were 415 patients with UEMI and 149 with NCMS. Compared with UEMI, patients with NCMS were younger, and had shorter dialysis duration, smaller proportion of diabetic nephropathy, more severe anemia, and more frequent hyperphosphatemia and hyperuricemia. Total Kt/V, creatinine clearance and residual renal function were not different. There was no difference in technique survival (P > 0.05) between the two groups, but rural patients showed lower overall survival (P < 0.05). Multivariate analysis showed that NCMS was independently associated with lower survival (RR = 1.49; 95% CI = 1.04-2.15). CONCLUSIONS: Medical insurance model is independently associated with PD patient survival.