Bioaerosols in urban environments: Trends and interactions with pollutants and meteorological variables based on quasi-climatological series.

Pollen grains emitted by urban vegetation are the main primary biological airborne particles (PBAPs) which alter the biological quality of urban air and have a significant impact on human health. This work analyses the interactions which exist between pollen-type PBAPs, meteorological variables, and air pollutants in the urban atmosphere so that the complex relationships and trends in future scenarios of changing environmental conditions can be assessed. For this study, the 1992-2018 pollen data series from the city of Granada (southeast Spain) was used, in which the dynamics of the total pollen as well as the 8 main pollen types (Cupressaceae, Olea, Pinus, Platanus, Poaceae, Populus, Quercus and Urticaceae) were analysed. The trend analysis showed that all except Urticaceae trended upward throughout the series. Spearman's correlations with meteorological variables showed that, in general, the most influential variables on the pollen concentrations were the daily maximum temperature, relative humidity, water vapor pressure, global radiation, and insolation, with different effects on different pollen types. Parallel analysis by neural networks (ANN) confirmed these variables as the predominant ones, especially global radiation. The correlation with atmospheric pollutants revealed that ozone was the pollutant with the highest influence, although some pollen types also showed correlation with NO2, SO2, CO and PM10. The Generalized Linear Models (GLM) between pollen and pollutants also indicated O3 as the most prominent variable. These results highlight the active role that pollen-type PBAPs have on urban air quality by establishing their interactions with meteorological variables and pollutants, thereby providing information on the behaviour of pollen emissions under changing environmental conditions.

Implementation of UV rotational Raman channel to improve aerosol retrievals from multiwavelength lidar.

Vibrational Raman effect is widely used in atmospheric lidar systems, but rotational Raman present several advantages. We have implemented a new setup in the ultraviolet branch of an existing multiwavelength lidar system to collect signal from rotational Raman lines of Oxygen and Nitrogen. We showed that, with an appropriate filter wavelength selection, the systematic error introduced in the particle optical properties due to temperature dependence was less than 4%. With this new setup, we have been able to retrieve aerosol extinction and backscatter coefficients profiles at 355 nm with 1-h time resolution during daytime and up to 1-min time resolution during nighttime.

Multispectral elastic scanning lidar for industrial flare research: characterizing the electronic subsystem and application.

This work deals with the analysis of the electronic subsystem of a multiwavelength elastic scanning lidar. Several calibration tests are applied to the Cubatão scanning lidar placed at the industrial area of Cubatão in the State of São Paulo (Brazil), in order to improve the knowledge of its performing itself and to design protocols for correcting lidar signal for undesirable instrumental effects. In particular, the trigger delay is assessed by means of zero-bin and bin-shift tests for analog (AN) and photo-counting (PC) signals, respectively. Dark current test is also performed to detect potential range-dependency that could affect lidar products. All tests were performed at different spatial resolutions. These instrumental corrections were applied to a case study of data acquired for characterizing the optical and microphysical properties of particles in an industrial flare. To that aim, a graphical method based on the space defined by the extinction-related Angström exponent versus its spectral curvature is used to derive the contribution of fine aerosol to extinction and the size of the fine aerosols in the industrial flare, therefore revealing features of the processes occurring inside the flame. Our study demonstrates the potential of this new technique for the study and measurement of industrial emissions.

Forest fire smoke layers observed in the free troposphere over Portugal with a multiwavelength Raman lidar: optical and microphysical properties.

Vertically resolved optical and microphysical properties of biomass burning aerosols, measured in 2011 with a multiwavelength Raman lidar, are presented. The transportation time, within 1-2 days (or less), pointed towards the presence of relatively fresh smoke particles over the site. Some strong layers aloft were observed with particle backscatter and extinction coefficients (at 355 nm) greater than 5 Mm(-1)sr(-1) and close to 300 Mm(-1), respectively. The particle intensive optical properties showed features different from the ones reported for aged smoke, but rather consistent with fresh smoke. The Ångström exponents were generally high, mainly above 1.4, indicating a dominating accumulation mode. Weak depolarization values, as shown by the small depolarization ratio of 5% or lower, were measured. Furthermore, the lidar ratio presented no clear wavelength dependency. The inversion of the lidar signals provided a set of microphysical properties including particle effective radius below 0.2 µm, which is less than values previously observed for aged smoke particles. Real and imaginary parts of refractive index of about 1.5-1.6 and 0.02i, respectively, were derived. The single scattering albedo was in the range between 0.85 and 0.93; these last two quantities indicate the nonnegligible absorbing characteristics of the observed particles.

Infrared lidar overlap function: an experimental determination.

The most recent works demonstrate that the lidar overlap function, which describes the overlap between the laser beam and the receiver field of view, can be determined experimentally for the 355 and 532 nm channels using Raman signals. Nevertheless, the Raman channels cannot be used to determine the lidar overlap for the infrared channel (1064 nm) because of their low intensity. In addition, many Raman lidar systems only provide inelastic signals with reasonable signal-to-noise ratio at nighttime. In view of this fact, this work presents a modification of that method, based on the comparison of attenuated backscatter profiles derived from lidar and ceilometer, to retrieve the overlap function for the lidar infrared channel. Similarly to the Raman overlap method, the approach presented here allows to derive the overlap correction without an explicit knowledge of all system parameters. The application of the proposed methodology will improve the potential of Raman lidars to investigate the aerosol microphysical properties in the planetary boundary layer, extending the information of 1064 nm backscatter profiles to the ground and allowing the retrieval of microphysical properties practically close to the surface.