Effect of Oxyfluorination of PFA-Coated Metal Mesh with Superhydrophobic Properties on the Filtration Performance of SiO2 Microparticles.

Recently, semiconductor wastewater treatment has received much attention due to the emergence of environmental issues. Acid-resistant coatings are essential for metal prefilters used in semiconductor wastewater treatment. Perfluoroalkoxy alkane is mainly used as an acid-resistant coating agent, since PFA has inherent superhydrophobicity, water permeability is lowered. To solve this problem, the surface of the PFA-coated metal mesh was treated via an oxyfluorination method in which an injected mixed gas of fluorine and oxygen reacted with the surface functional groups. Surface analysis, water contact angle measurement, and water permeability tests were performed on the surface-treated PFA-coated mesh. Consequently, the superhydrophobic surface was effectively converted to a hydrophobic surface as the PFA coating layer was surface-modified with C-O-OH functional groups via the oxyfluorination reaction. As a result of using simulation solutions that float silica particles of various sizes, the permeability and particle removal rate of the surface-modified PFA-coated stainless-steel mesh were improved compared to those before surface modification. Therefore, the oxyfluorination treatment used in this study was suitable for improving the filtration performance of SiO2 microparticles in the PFA-coated stainless-steel mesh.

Coil spring-powered pump with inertial microfluidic chip for size-based isolation and enrichment of biological cells.

Microfluidic chips have been widely used for in vitro diagnostics using pretreatment of biological samples; however, biologists and clinical researchers have difficulties using them in resource-limited settings. Sample injection systems for microfluidic chips are bulky, expensive, electricity-powered, and complex. A coiled spring-powered device, which can be used to isolate variously sized cells with high efficiency continuously and passively, was developed for portable, low-cost, electricity-free, and simple sample injection. The flow driving power was provided by releasing the compression spring in the mechanical syringe driver with a one-click action. In general, a syringe pump generates a stable passive flow rate. However, the syringe pumps are large in size and expensive because they have many functions such as infusion/withdrawal flow injection and the use of syringes of various sizes, allowing them to be applied in a variety of applications performed in the laboratory. In addition, it is not suitable for portable devices because of the considerable amount of electric power required. To overcome these drawbacks, we developed a device prototype that sorts different-sized particles and separates rare tumor cells or blood cells from blood with high efficiency. The performance of the coiled spring-powered device was evaluated and found to be comparable with that of syringe pump-powered devices. In situations where trained personnel cannot handle microfluidic chips for isolating circulating biomarkers (CTCs, WBCs, or plasma) from blood samples, the coiled spring-powered device can provide diagnostic tools, especially in resource-limited countries.

Terrain Feature Estimation Method for a Lower Limb Exoskeleton Using Kinematic Analysis and Center of Pressure.

While controlling a lower limb exoskeleton providing walking assistance to wearers, the walking terrain is an important factor that should be considered for meeting performance and safety requirements. Therefore, we developed a method to estimate the slope and elevation using the contact points between the limb exoskeleton and ground. We used the center of pressure as a contact point on the ground and calculated the location of the contact points on the walking terrain based on kinematic analysis of the exoskeleton. Then, a set of contact points collected from each step during walking was modeled as the plane that represents the surface of the walking terrain through the least-square method. Finally, by comparing the normal vectors of the modeled planes for each step, features of the walking terrain were estimated. We analyzed the estimation accuracy of the proposed method through experiments on level ground, stairs, and a ramp. Classification using the estimated features showed recognition accuracy higher than 95% for all experimental motions. The proposed method approximately analyzed the movement of the exoskeleton on various terrains even though no prior information on the walking terrain was provided. The method can enable exoskeleton systems to actively assist walking in various environments.

Modularized dynamic cell culture platform for efficient production of extracellular vesicles and sequential analysis.

Extracellular vesicles (EVs) are nanometer-sized particles naturally secreted by cells for intercellular communication that encapsulate bioactive cargo, such as proteins and RNA, with a lipid bilayer. Tumor cell-derived EVs (tdEVs) are particularly promising biomarkers for cancer research because their contents reflect the cell of origin. In most studies, tdEVs have been obtained from cancer cells cultured under static conditions, thus lacking the ability to recapitulate the microenvironment of cells in vivo. Recent developments in perfusable cell culture systems have allowed oxygen and a nutrient gradient to mimic the physiological and cellular microenvironment. However, as these systems are perfused by circulating the culture medium within the unified structure, independently harvesting cells and EVs at each time point for analysis presents a limitation. In this study, a modularized cell culture system is designed for the perfusion and real-time collection of EVs. The system consists of three detachable chambers, one each for fresh medium, cell culture, and EV collection. The fresh medium flows from the medium chamber to the culture chamber at a flow rate controlled by the hydraulic pressure injected with a syringe pump. When the culture medium containing EVs exceeds a certain volume within the chamber, it overflows into the collection chamber to harvest EVs. The compact and modularized chambers are highly interoperable with conventional cell culture modalities used in the laboratory, thus enabling various EV-based assays.

Bone Regeneration Using a Mixture of Silicon-Substituted Coral HA and ß-TCP in a Rat Calvarial Bone Defect Model.

The demand of bone graft materials has been increasing. Among various origins of bone graft materials, natural coral composed of up to 99% calcium carbonate was chosen and converted into hydroxyapatite (HA); silicon was then substituted into the HA. Then, the Si-HA was mixed with ß-tricalcium phosphate (TCP) in the ratios 100:0 (S100T0), 70:30 (S70T30), 60:40 (S60T40), and 50:50 (S50T50). The materials were implanted for four and eight weeks in a rat calvarial bone defect model (8 mm). The MBCPTM (HA:ß-TCP = 60:40, Biomatalante, Vigneux de Bretagne, France) was used as a control. After euthanasia, the bone tissue was analyzed by making histological slides. From the results, S60T40 showed the fastest bone regeneration in four weeks (p < 0.05). In addition, S60T40, S50T50, and MBCPTM showed significant new bone formation in eight weeks (p < 0.05). In conclusion, Si-HA/TCP showed potential as a bone graft material.